Merge tag 'for-linus-3.3' of git://git.infradead.org/~dwmw2/mtd-3.3

 - Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
 - Fix breakage with MTD suspend caused by the API rework
 - Fix a problem with resetting the MX28 BCH module
 - A couple of other trivial fixes

* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
  Revert "mtd: atmel_nand: optimize read/write buffer functions"
  mtd: fix MTD suspend
  jffs2: do not initialize variable unnecessarily
  mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
  mtd: nand: fix typo in comment

drivers/mtd/mtdcore.c

@@ -119,7 +119,7 @@ static int mtd_cls_suspend(struct device *dev, pm_message_t state)
 {
 	struct mtd_info *mtd = dev_get_drvdata(dev);
 
-	return mtd_suspend(mtd);
+	return mtd ? mtd_suspend(mtd) : 0;
 }
 
 static int mtd_cls_resume(struct device *dev)

drivers/mtd/nand/atmel_nand.c

@@ -161,6 +161,37 @@ static int atmel_nand_device_ready(struct mtd_info *mtd)
                 !!host->board->rdy_pin_active_low;
 }
 
+/*
+ * Minimal-overhead PIO for data access.
+ */
+static void atmel_read_buf8(struct mtd_info *mtd, u8 *buf, int len)
+{
+	struct nand_chip	*nand_chip = mtd->priv;
+
+	__raw_readsb(nand_chip->IO_ADDR_R, buf, len);
+}
+
+static void atmel_read_buf16(struct mtd_info *mtd, u8 *buf, int len)
+{
+	struct nand_chip	*nand_chip = mtd->priv;
+
+	__raw_readsw(nand_chip->IO_ADDR_R, buf, len / 2);
+}
+
+static void atmel_write_buf8(struct mtd_info *mtd, const u8 *buf, int len)
+{
+	struct nand_chip	*nand_chip = mtd->priv;
+
+	__raw_writesb(nand_chip->IO_ADDR_W, buf, len);
+}
+
+static void atmel_write_buf16(struct mtd_info *mtd, const u8 *buf, int len)
+{
+	struct nand_chip	*nand_chip = mtd->priv;
+
+	__raw_writesw(nand_chip->IO_ADDR_W, buf, len / 2);
+}
+
 static void dma_complete_func(void *completion)
 {
 	complete(completion);
@@ -235,27 +266,33 @@ static int atmel_nand_dma_op(struct mtd_info *mtd, void *buf, int len,
 static void atmel_read_buf(struct mtd_info *mtd, u8 *buf, int len)
 {
 	struct nand_chip *chip = mtd->priv;
+	struct atmel_nand_host *host = chip->priv;
 
 	if (use_dma && len > mtd->oobsize)
 		/* only use DMA for bigger than oob size: better performances */
 		if (atmel_nand_dma_op(mtd, buf, len, 1) == 0)
 			return;
 
-	/* if no DMA operation possible, use PIO */
-	memcpy_fromio(buf, chip->IO_ADDR_R, len);
+	if (host->board->bus_width_16)
+		atmel_read_buf16(mtd, buf, len);
+	else
+		atmel_read_buf8(mtd, buf, len);
 }
 
 static void atmel_write_buf(struct mtd_info *mtd, const u8 *buf, int len)
 {
 	struct nand_chip *chip = mtd->priv;
+	struct atmel_nand_host *host = chip->priv;
 
 	if (use_dma && len > mtd->oobsize)
 		/* only use DMA for bigger than oob size: better performances */
 		if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) == 0)
 			return;
 
-	/* if no DMA operation possible, use PIO */
-	memcpy_toio(chip->IO_ADDR_W, buf, len);
+	if (host->board->bus_width_16)
+		atmel_write_buf16(mtd, buf, len);
+	else
+		atmel_write_buf8(mtd, buf, len);
 }
 
 /*

drivers/mtd/nand/gpmi-nand/gpmi-lib.c

@@ -69,17 +69,19 @@ static int clear_poll_bit(void __iomem *addr, u32 mask)
  *  [1] enable the module.
  *  [2] reset the module.
  *
- * In most of the cases, it's ok. But there is a hardware bug in the BCH block.
+ * In most of the cases, it's ok.
+ * But in MX23, there is a hardware bug in the BCH block (see erratum #2847).
  * If you try to soft reset the BCH block, it becomes unusable until
  * the next hard reset. This case occurs in the NAND boot mode. When the board
  * boots by NAND, the ROM of the chip will initialize the BCH blocks itself.
  * So If the driver tries to reset the BCH again, the BCH will not work anymore.
- * You will see a DMA timeout in this case.
+ * You will see a DMA timeout in this case. The bug has been fixed
+ * in the following chips, such as MX28.
  *
  * To avoid this bug, just add a new parameter `just_enable` for
  * the mxs_reset_block(), and rewrite it here.
  */
-int gpmi_reset_block(void __iomem *reset_addr, bool just_enable)
+static int gpmi_reset_block(void __iomem *reset_addr, bool just_enable)
 {
 	int ret;
 	int timeout = 0x400;
@@ -206,7 +208,15 @@ int bch_set_geometry(struct gpmi_nand_data *this)
 	if (ret)
 		goto err_out;
 
-	ret = gpmi_reset_block(r->bch_regs, true);
+	/*
+	* Due to erratum #2847 of the MX23, the BCH cannot be soft reset on this
+	* chip, otherwise it will lock up. So we skip resetting BCH on the MX23.
+	* On the other hand, the MX28 needs the reset, because one case has been
+	* seen where the BCH produced ECC errors constantly after 10000
+	* consecutive reboots. The latter case has not been seen on the MX23 yet,
+	* still we don't know if it could happen there as well.
+	*/
+	ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this));
 	if (ret)
 		goto err_out;
 

drivers/mtd/nand/nand_base.c

@@ -2588,7 +2588,7 @@ int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
 	instr->state = MTD_ERASING;
 
 	while (len) {
-		/* Heck if we have a bad block, we do not erase bad blocks! */
+		/* Check if we have a bad block, we do not erase bad blocks! */
 		if (nand_block_checkbad(mtd, ((loff_t) page) <<
 					chip->page_shift, 0, allowbbt)) {
 			pr_warn("%s: attempt to erase a bad block at page 0x%08x\n",

fs/jffs2/erase.c

@@ -335,7 +335,7 @@ static int jffs2_block_check_erase(struct jffs2_sb_info *c, struct jffs2_erasebl
 	void *ebuf;
 	uint32_t ofs;
 	size_t retlen;
-	int ret = -EIO;
+	int ret;
 	unsigned long *wordebuf;
 
 	ret = mtd_point(c->mtd, jeb->offset, c->sector_size, &retlen,

include/linux/mtd/mtd.h

@@ -427,9 +427,7 @@ static inline int mtd_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 
 static inline int mtd_suspend(struct mtd_info *mtd)
 {
-	if (!mtd->suspend)
-		return -EOPNOTSUPP;
-	return mtd->suspend(mtd);
+	return mtd->suspend ? mtd->suspend(mtd) : 0;
 }
 
 static inline void mtd_resume(struct mtd_info *mtd)