Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Arnd Bergmann:
 "The DT branch adds a lot of new stuff for additional SoC and board
  support.  The branch is the largest one and contains 513 out of the
  total 972 non-merge arm-soc changesets for 3.19.

  Most of the changes are about enabling additional on-chip devices for
  existing machines, but there are also an unusual number of new SoC
  types being added this time:

   - AMLogic Meson8
   - ARM Realview in DT mode
   - Allwinner A80
   - Broadcom BCM47081
   - Broadcom Cygnus
   - Freescale LS1021A
   - Freescale Vybrid 500 series
   - Mediatek MT6592, MT8127, MT8135
   - STMicroelectronics STiH410
   - Samsung Exynos4415

  The level of support for the above differs widely, some are just stubs
  with nothing more than CPU, memory and a UART, but others are fairly
  complete.  As usual, these get extended over time.

  There are also many new boards getting added, this is the list of
  model strings that are showing up in new dts files:

   - ARM RealView PB1176
   - Altera SOCFPGA Arria 10
   - Asus RT-N18U (BCM47081)
   - Buffalo WZR-1750DHP (BCM4708)
   - Buffalo WZR-600DHP2 (BCM47081)
   - Cygnus Enterprise Phone (BCM911360_ENTPHN)
   - D-Link DIR-665
   - Google Spring
   - IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
   - IGEPv2 Rev. F (TI OMAP AM/DM37x)
   - LS1021A QDS Board
   - LS1021A TWR Board
   - LeMaker Banana Pi
   - MarsBoard RK3066
   - MediaTek MT8127 Moose Board
   - MediaTek MT8135 evaluation board
   - Mele M3
   - Merrii A80 Optimus Board
   - Netgear R6300 V2 (BCM4708)
   - Nomadik STN8815NHK
   - NovaTech OrionLXm
   - Olimex A20-OLinuXino-LIME2
   - Raspberry Pi Model B+
   - STiH410 B2120
   - Samsung Monk board
   - Samsung Rinato board
   - Synology DS213j
   - Synology DS414
   - TBS2910 Matrix ARM mini PC
   - TI AM5728 BeagleBoard-X15
   - Toradex Colibri VF50 on Colibri Evaluation Board
   - Zynq ZYBO Development Board

  Other notable changes include:

   - exynos: cleanup of existing dts files
   - mvebu: improved pinctrl support for Armada 370/XP
   - nomadik: restructuring dts files
   - omap: added CAN bus support
   - shmobile: added clock support for some SoCs
   - shmobile: added sound support for some SoCs
   - sirf: reset controller support
   - sunxi: continuing the relicensing under dual GPL/MIT
   - sunxi: lots of new on-chip device support
   - sunxi: working simplefb support (long awaited)
   - various: provide stdout-path property for earlycon"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (510 commits)
  ARM: dts: rk3288: add arm,cpu-registers-not-fw-configured
  Revert "ARM: dts: rockchip: temporarily disable smp on rk3288"
  ARM: BCM5301X: Add DT for Buffalo WZR-600DHP2
  ARM: BCM5301X: Add DT for Asus RT-N18U
  ARM: BCM5301X: Add DT for Buffalo WZR-1750DHP
  ARM: BCM5301X: Add DT for Netgear R6300 V2
  ARM: BCM5301X: Add buttons for Netgear R6250
  ARM: dts: rockchip: Add input voltage supply regulators in pmic for Marsboard
  ARM: BCM5301X: Add IRQs to Broadcom's bus-axi in DTS file
  arm: dts: zynq: Add Digilent ZYBO board
  arm: dts: zynq: Move crystal freq. to board level
  doc: dt: vendor-prefixes: Add Digilent Inc
  Documentation: devicetree: Fix Xilinx VDMA specification
  ARM: dts: rockchip: set FIFO size for SDMMC, SDIO and EMMC on rk3066 and rk3188
  ARM: dts: rockchip: add label property for leds on Radxa Rock
  ARM: BCM5301X: Add LEDs for Netgear R6250 V1
  ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file
  ARM: dts: add sysreg phandle to i2c device nodes for exynos
  ARM: dts: Remove unused bootargs from exynos3250-rinato
  ARM: dts: add board dts file for Exynos3250-based Monk board
  ...

Documentation/devicetree/bindings/arm/arm-boards

@@ -92,3 +92,68 @@ Required nodes:
 - core-module: the root node to the Versatile platforms must have
   a core-module with regs and the compatible strings
   "arm,core-module-versatile", "syscon"
+
+ARM RealView Boards
+-------------------
+The RealView boards cover tailored evaluation boards that are used to explore
+the ARM11 and Cortex A-8 and Cortex A-9 processors.
+
+Required properties (in root node):
+	/* RealView Emulation Baseboard */
+	compatible = "arm,realview-eb";
+	 /* RealView Platform Baseboard for ARM1176JZF-S */
+	compatible = "arm,realview-pb1176";
+	/* RealView Platform Baseboard for ARM11 MPCore */
+	compatible = "arm,realview-pb11mp";
+	/* RealView Platform Baseboard for Cortex A-8 */
+	compatible = "arm,realview-pba8";
+	/* RealView Platform Baseboard Explore for Cortex A-9 */
+	compatible = "arm,realview-pbx";
+
+Required nodes:
+
+- soc: some node of the RealView platforms must be the SoC
+  node that contain the SoC-specific devices, withe the compatible
+  string set to one of these tuples:
+   "arm,realview-eb-soc", "simple-bus"
+   "arm,realview-pb1176-soc", "simple-bus"
+   "arm,realview-pb11mp-soc", "simple-bus"
+   "arm,realview-pba8-soc", "simple-bus"
+   "arm,realview-pbx-soc", "simple-bus"
+
+- syscon: some subnode of the RealView SoC node must be a
+  system controller node pointing to the control registers,
+  with the compatible string set to one of these tuples:
+   "arm,realview-eb-syscon", "syscon"
+   "arm,realview-pb1176-syscon", "syscon"
+   "arm,realview-pb11mp-syscon", "syscon"
+   "arm,realview-pba8-syscon", "syscon"
+   "arm,realview-pbx-syscon", "syscon"
+
+  Required properties for the system controller:
+  - regs: the location and size of the system controller registers,
+    one range of 0x1000 bytes.
+
+Example:
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "skeleton.dtsi"
+
+/ {
+	model = "ARM RealView PB1176 with device tree";
+	compatible = "arm,realview-pb1176";
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "arm,realview-pb1176-soc", "simple-bus";
+		ranges;
+
+		syscon: syscon@10000000 {
+			compatible = "arm,realview-syscon", "syscon";
+			reg = <0x10000000 0x1000>;
+		};
+
+	};
+};

Documentation/devicetree/bindings/arm/bcm/cygnus.txt

+Broadcom Cygnus device tree bindings
+------------------------------------
+
+
+Boards with Cygnus SoCs shall have the following properties:
+
+Required root node property:
+
+BCM11300
+compatible = "brcm,bcm11300", "brcm,cygnus";
+
+BCM11320
+compatible = "brcm,bcm11320", "brcm,cygnus";
+
+BCM11350
+compatible = "brcm,bcm11350", "brcm,cygnus";
+
+BCM11360
+compatible = "brcm,bcm11360", "brcm,cygnus";
+
+BCM58300
+compatible = "brcm,bcm58300", "brcm,cygnus";
+
+BCM58302
+compatible = "brcm,bcm58302", "brcm,cygnus";
+
+BCM58303
+compatible = "brcm,bcm58303", "brcm,cygnus";
+
+BCM58305
+compatible = "brcm,bcm58305", "brcm,cygnus";

Documentation/devicetree/bindings/arm/fsl.txt

@@ -74,3 +74,41 @@ Required root node properties:
 i.MX6q generic board
 Required root node properties:
     - compatible = "fsl,imx6q";
+
+
+Freescale LS1021A Platform Device Tree Bindings
+------------------------------------------------
+
+Required root node compatible properties:
+  - compatible = "fsl,ls1021a";
+
+Freescale LS1021A SoC-specific Device Tree Bindings
+-------------------------------------------
+
+Freescale SCFG
+  SCFG is the supplemental configuration unit, that provides SoC specific
+configuration and status registers for the chip. Such as getting PEX port
+status.
+  Required properties:
+  - compatible: should be "fsl,ls1021a-scfg"
+  - reg: should contain base address and length of SCFG memory-mapped registers
+
+Example:
+	scfg: scfg@1570000 {
+		compatible = "fsl,ls1021a-scfg";
+		reg = <0x0 0x1570000 0x0 0x10000>;
+	};
+
+Freescale DCFG
+  DCFG is the device configuration unit, that provides general purpose
+configuration and status for the device. Such as setting the secondary
+core start address and release the secondary core from holdoff and startup.
+  Required properties:
+  - compatible: should be "fsl,ls1021a-dcfg"
+  - reg : should contain base address and length of DCFG memory-mapped registers
+
+Example:
+	dcfg: dcfg@1ee0000 {
+		compatible = "fsl,ls1021a-dcfg";
+		reg = <0x0 0x1ee0000 0x0 0x10000>;
+	};

Documentation/devicetree/bindings/arm/gic.txt

@@ -17,6 +17,7 @@ Main node required properties:
 	"arm,cortex-a7-gic"
 	"arm,arm11mp-gic"
 	"brcm,brahma-b15-gic"
+	"arm,arm1176jzf-devchip-gic"
 - interrupt-controller : Identifies the node as an interrupt controller
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source.  The type shall be a <u32> and the value shall be 3.

Documentation/devicetree/bindings/arm/marvell,berlin.txt

@@ -106,11 +106,21 @@ Required subnode-properties:
 - groups: a list of strings describing the group names.
 - function: a string describing the function used to mux the groups.
 
+* Reset controller binding
+
+A reset controller is part of the chip control registers set. The chip control
+node also provides the reset. The register set is not at the same offset between
+Berlin SoCs.
+
+Required property:
+- #reset-cells: must be set to 2
+
 Example:
 
 chip: chip-control@ea0000 {
 	compatible = "marvell,berlin2-chip-ctrl";
 	#clock-cells = <1>;
+	#reset-cells = <2>;
 	reg = <0xea0000 0x400>;
 	clocks = <&refclk>, <&externaldev 0>;
 	clock-names = "refclk", "video_ext0";

Documentation/devicetree/bindings/arm/mediatek.txt

-Mediatek MT6589 Platforms Device Tree Bindings
+MediaTek mt65xx & mt81xx Platforms Device Tree Bindings
 
-Boards with a SoC of the Mediatek MT6589 shall have the following property:
+Boards with a MediaTek mt65xx/mt81xx SoC shall have the following property:
 
 Required root node property:
 
-compatible: must contain "mediatek,mt6589"
+compatible: Must contain one of
+   "mediatek,mt6589"
+   "mediatek,mt6592"
+   "mediatek,mt8127"
+   "mediatek,mt8135"
 
 
 Supported boards:
@@ -12,3 +16,12 @@ Supported boards:
 - bq Aquaris5 smart phone:
     Required root node properties:
       - compatible = "mundoreader,bq-aquaris5", "mediatek,mt6589";
+- Evaluation board for MT6592:
+    Required root node properties:
+      - compatible = "mediatek,mt6592-evb", "mediatek,mt6592";
+- MTK mt8127 tablet moose EVB:
+    Required root node properties:
+      - compatible = "mediatek,mt8127-moose", "mediatek,mt8127";
+- MTK mt8135 tablet EVB:
+    Required root node properties:
+      - compatible = "mediatek,mt8135-evbp1", "mediatek,mt8135";

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -132,6 +132,9 @@ Boards:
 - AM335X Bone : Low cost community board
   compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
 
+- AM335X OrionLXm : Substation Automation Platform
+  compatible = "novatech,am335x-lxm", "ti,am33xx"
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"
 

Documentation/devicetree/bindings/arm/rockchip.txt

 Rockchip platforms device tree bindings
 ---------------------------------------
 
+- MarsBoard RK3066 board:
+    Required root node properties:
+      - compatible = "haoyu,marsboard-rk3066", "rockchip,rk3066a";
+
 - bq Curie 2 tablet:
     Required root node properties:
       - compatible = "mundoreader,bq-curie2", "rockchip,rk3066a";

Documentation/devicetree/bindings/arm/samsung-boards.txt

-* Samsung's Exynos4210 based SMDKV310 evaluation board
-
-SMDKV310 evaluation board is based on Samsung's Exynos4210 SoC.
+* Samsung's Exynos SoC based boards
 
 Required root node properties:
     - compatible = should be one or more of the following.
-        (a) "samsung,smdkv310" - for Samsung's SMDKV310 eval board.
-        (b) "samsung,exynos4210"  - for boards based on Exynos4210 SoC.
+	- "samsung,monk"	- for Exynos3250-based Samsung Simband board.
+	- "samsung,rinato"	- for Exynos3250-based Samsung Gear2 board.
+	- "samsung,smdkv310"	- for Exynos4210-based Samsung SMDKV310 eval board.
+	- "samsung,trats"	- for Exynos4210-based Tizen Reference board.
+	- "samsung,universal_c210" - for Exynos4210-based Samsung board.
+	- "samsung,smdk4412",	- for Exynos4412-based Samsung SMDK4412 eval board.
+	- "samsung,trats2"	- for Exynos4412-based Tizen Reference board.
+	- "samsung,smdk5250"	- for Exynos5250-based Samsung SMDK5250 eval board.
+	- "samsung,xyref5260"	- for Exynos5260-based Samsung board.
+	- "samsung,smdk5410"	- for Exynos5410-based Samsung SMDK5410 eval board.
+	- "samsung,smdk5420"	- for Exynos5420-based Samsung SMDK5420 eval board.
+	- "samsung,sd5v1"	- for Exynos5440-based Samsung board.
+	- "samsung,ssdk5440"	- for Exynos5440-based Samsung board.
 
 Optional:
     - firmware node, specifying presence and type of secure firmware:

Documentation/devicetree/bindings/arm/ste-nomadik.txt

@@ -10,6 +10,12 @@ Required root node property: src
 
 Boards with the Nomadik SoC include:
 
+Nomadik NHK-15 board manufactured by ST Microelectronics:
+
+Required root node property:
+
+compatible="st,nomadik-nhk-15";
+
 S8815 "MiniKit" manufactured by Calao Systems:
 
 Required root node property:

Documentation/devicetree/bindings/clock/bcm-cygnus-clock.txt

+Broadcom Cygnus Clocks
+
+This binding uses the common clock binding:
+Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Currently various "fixed" clocks are declared for peripheral drivers that use
+the common clock framework to reference their core clocks. Proper support of
+these clocks will be added later
+
+Device tree example:
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <1>;
+			clock-frequency = <25000000>;
+		};
+
+		apb_clk: apb_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		periph_clk: periph_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <500000000>;
+		};
+	};

Documentation/devicetree/bindings/clock/vf610-clock.txt

@@ -5,6 +5,19 @@ Required properties:
 - reg: Address and length of the register set
 - #clock-cells: Should be <1>
 
+Optional properties:
+- clocks: list of clock identifiers which are external input clocks to the
+	given clock controller. Please refer the next section to find
+	the input clocks for a given controller.
+- clock-names: list of names of clocks which are exteral input clocks to the
+	given clock controller.
+
+Input clocks for top clock controller:
+	- sxosc (external crystal oscillator 32KHz, recommended)
+	- fxosc (external crystal oscillator 24MHz, recommended)
+	- audio_ext
+	- enet_ext
+
 The clock consumer should specify the desired clock by having the clock
 ID in its "clocks" phandle cell. See include/dt-bindings/clock/vf610-clock.h
 for the full list of VF610 clock IDs.
@@ -15,6 +28,8 @@ clks: ccm@4006b000 {
 	compatible = "fsl,vf610-ccm";
 	reg = <0x4006b000 0x1000>;
 	#clock-cells = <1>;
+	clocks = <&sxosc>, <&fxosc>;
+	clock-names = "sxosc", "fxosc";
 };
 
 uart1: serial@40028000 {

Documentation/devicetree/bindings/dma/xilinx/xilinx_vdma.txt

@@ -25,7 +25,7 @@ Required child node properties:
 - compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or
 	"xlnx,axi-vdma-s2mm-channel".
 - interrupts: Should contain per channel VDMA interrupts.
-- xlnx,data-width: Should contain the stream data width, take values
+- xlnx,datawidth: Should contain the stream data width, take values
 	{32,64...1024}.
 
 Optional child node properties:

Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt

@@ -32,6 +32,7 @@ Optional properties:
     specified, default value is 0.
   - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
     specified, the default value in Hz is 100000.
+  - samsung,sysreg-phandle - handle to syscon used to control the system registers
 
 Example:
 

Documentation/devicetree/bindings/i2c/trivial-devices.txt

@@ -56,6 +56,8 @@ gmt,g751		G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire In
 infineon,slb9635tt	Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz)
 infineon,slb9645tt	Infineon SLB9645 I2C TPM (new protocol, max 400khz)
 isl,isl12057		Intersil ISL12057 I2C RTC Chip
+isil,isl29028           (deprecated, use isl)
+isl,isl29028            Intersil ISL29028 Ambient Light and Proximity Sensor
 maxim,ds1050		5 Bit Programmable, Pulse-Width Modulator
 maxim,max1237		Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs
 maxim,max6625		9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface

Documentation/devicetree/bindings/timer/renesas,mtu2.txt

-* Renesas R-Car Multi-Function Timer Pulse Unit 2 (MTU2)
+* Renesas Multi-Function Timer Pulse Unit 2 (MTU2)
 
 The MTU2 is a multi-purpose, multi-channel timer/counter with configurable
 clock inputs and programmable compare match.

Documentation/devicetree/bindings/timer/renesas,tmu.txt

-* Renesas R-Car Timer Unit (TMU)
+* Renesas R-Mobile/R-Car Timer Unit (TMU)
 
 The TMU is a 32-bit timer/counter with configurable clock inputs and
 programmable compare match.
@@ -9,6 +9,8 @@ are independent. The TMU hardware supports up to three channels.
 Required Properties:
 
   - compatible: must contain one or more of the following:
+    - "renesas,tmu-r8a7740" for the r8a7740 TMU
+    - "renesas,tmu-r8a7778" for the r8a7778 TMU
     - "renesas,tmu-r8a7779" for the r8a7779 TMU
     - "renesas,tmu" for any TMU.
       This is a fallback for the above renesas,tmu-* entries

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -41,6 +41,7 @@ dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 denx	Denx Software Engineering
 digi	Digi International Inc.
+digilent	Diglent, Inc.
 dlg	Dialog Semiconductor
 dlink	D-Link Corporation
 dmo	Data Modul AG
@@ -78,6 +79,7 @@ innolux	Innolux Corporation
 intel	Intel Corporation
 intercontrol	Inter Control Group
 isee	ISEE 2007 S.L.
+isil    Intersil (deprecated, use isl)
 isl	Intersil
 karo	Ka-Ro electronics GmbH
 keymile	Keymile GmbH
@@ -150,6 +152,7 @@ st	STMicroelectronics
 ste	ST-Ericsson
 stericsson	ST-Ericsson
 synology	Synology, Inc.
+tbs	TBS Technologies
 thine	THine Electronics, Inc.
 ti	Texas Instruments
 tlm	Trusted Logic Mobility

arch/arm/boot/dts/Makefile

@@ -54,8 +54,17 @@ dtb-$(CONFIG_ARCH_AT91)	+= at91-sama5d4ek.dtb
 dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_AXXIA) += axm5516-amarillo.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
-dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
+dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b-plus.dtb
+dtb-$(CONFIG_ARCH_BCM_5301X) += \
+	bcm4708-buffalo-wzr-1750dhp.dtb \
+	bcm4708-netgear-r6250.dtb \
+	bcm4708-netgear-r6300-v2.dtb \
+	bcm47081-asus-rt-n18u.dtb \
+	bcm47081-buffalo-wzr-600dhp2.dtb
 dtb-$(CONFIG_ARCH_BCM_63XX) += bcm963138dvt.dtb
+dtb-$(CONFIG_ARCH_BCM_CYGNUS) += bcm911360_entphn.dtb \
+	bcm911360k.dtb \
+	bcm958300k.dtb
 dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \
 	bcm21664-garnet.dtb
 dtb-$(CONFIG_ARCH_BERLIN) += \
@@ -67,7 +76,9 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \
 dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
 dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
-dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
+dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-monk.dtb \
+	exynos3250-rinato.dtb \
+	exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
 	exynos4210-trats.dtb \
 	exynos4210-universal_c210.dtb \
@@ -81,6 +92,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
+	exynos5250-spring.dtb \
 	exynos5260-xyref5260.dtb \
 	exynos5410-smdk5410.dtb \
 	exynos5420-arndale-octa.dtb \
@@ -104,6 +116,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-b3.dtb \
 	kirkwood-d2net.dtb \
 	kirkwood-db-88f6281.dtb \
 	kirkwood-db-88f6282.dtb \
+	kirkwood-dir665.dtb \
 	kirkwood-dns320.dtb \
 	kirkwood-dns325.dtb \
 	kirkwood-dockstar.dtb \
@@ -240,6 +253,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-sabrelite.dtb \
 	imx6q-sabresd.dtb \
 	imx6q-sbc6x.dtb \
+	imx6q-tbs2910.dtb \
 	imx6q-udoo.dtb \
 	imx6q-wandboard.dtb \
 	imx6q-wandboard-revb1.dtb \
@@ -250,6 +264,9 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx6q-tx6q-1110.dtb \
 	imx6sl-evk.dtb \
 	imx6sx-sdb.dtb \
+	ls1021a-qds.dtb \
+	ls1021a-twr.dtb \
+	vf500-colibri-eval-v3.dtb \
 	vf610-colibri-eval-v3.dtb \
 	vf610-cosmic.dtb \
 	vf610-twr.dtb
@@ -274,7 +291,8 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
 	imx28-tx28.dtb
-dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb
+dtb-$(CONFIG_ARCH_NOMADIK) += ste-nomadik-s8815.dtb \
+	ste-nomadik-nhk15.dtb
 dtb-$(CONFIG_ARCH_NSPIRE) += nspire-cx.dtb \
 	nspire-tp.dtb \
 	nspire-clp.dtb
@@ -302,7 +320,9 @@ dtb-$(CONFIG_ARCH_OMAP3) += am3517-craneboard.dtb \
 	omap3-ha.dtb \
 	omap3-ha-lcd.dtb \
 	omap3-igep0020.dtb \
+	omap3-igep0020-rev-f.dtb \
 	omap3-igep0030.dtb \
+	omap3-igep0030-rev-g.dtb \
 	omap3-ldp.dtb \
 	omap3-lilly-dbb056.dtb \
 	omap3-n900.dtb \
@@ -331,7 +351,8 @@ dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
 	am335x-nano.dtb \
-	am335x-pepper.dtb
+	am335x-pepper.dtb \
+	am335x-lxm.dtb
 dtb-$(CONFIG_ARCH_OMAP4) += omap4-duovero-parlor.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
@@ -347,6 +368,7 @@ dtb-$(CONFIG_SOC_OMAP5) += omap5-cm-t54.dtb \
 	omap5-sbc-t54.dtb \
 	omap5-uevm.dtb
 dtb-$(CONFIG_SOC_DRA7XX) += dra7-evm.dtb \
+	am57xx-beagle-x15.dtb \
 	dra72-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \
 	orion5x-lacie-ethernet-disk-mini-v2.dtb \
@@ -363,8 +385,10 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8974-sony-xperia-honami.dtb
+dtb-$(CONFIG_ARCH_REALVIEW) += arm-realview-pb1176.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += \
 	rk3066a-bqcurie2.dtb \
+	rk3066a-marsboard.dtb \
 	rk3188-radxarock.dtb \
 	rk3288-evb-act8846.dtb \
 	rk3288-evb-rk808.dtb
@@ -396,6 +420,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += emev2-kzm9d.dtb \
 	r8a7791-koelsch.dtb \
 	r8a7794-alt.dtb
 dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_arria5_socdk.dtb \
+	socfpga_arria10_socdk.dtb \
 	socfpga_cyclone5_socdk.dtb \
 	socfpga_cyclone5_sockit.dtb \
 	socfpga_cyclone5_socrates.dtb \
@@ -408,6 +433,7 @@ dtb-$(CONFIG_ARCH_SPEAR3XX)+= spear300-evb.dtb \
 	spear320-hmi.dtb
 dtb-$(CONFIG_ARCH_SPEAR6XX)+= spear600-evb.dtb
 dtb-$(CONFIG_ARCH_STI)+= stih407-b2120.dtb \
+	stih410-b2120.dtb \
 	stih415-b2000.dtb \
 	stih415-b2020.dtb \
 	stih416-b2000.dtb \
@@ -434,15 +460,20 @@ dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31-hummingbird.dtb \
 	sun6i-a31-m9.dtb
 dtb-$(CONFIG_MACH_SUN7I) += \
+	sun7i-a20-bananapi.dtb \
 	sun7i-a20-cubieboard2.dtb \
 	sun7i-a20-cubietruck.dtb \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-m3.dtb \
 	sun7i-a20-olinuxino-lime.dtb \
+	sun7i-a20-olinuxino-lime2.dtb \
 	sun7i-a20-olinuxino-micro.dtb \
 	sun7i-a20-pcduino3.dtb
 dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-a23-ippo-q8h-v5.dtb
+dtb-$(CONFIG_MACH_SUN9I) += \
+	sun9i-a80-optimus.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
 	tegra20-medcom-wide.dtb \
@@ -488,13 +519,15 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-parallella.dtb \
 	zynq-zc702.dtb \
 	zynq-zc706.dtb \
-	zynq-zed.dtb
+	zynq-zed.dtb \
+	zynq-zybo.dtb
 dtb-$(CONFIG_MACH_ARMADA_370) += \
 	armada-370-db.dtb \
 	armada-370-mirabox.dtb \
 	armada-370-netgear-rn102.dtb \
 	armada-370-netgear-rn104.dtb \
-	armada-370-rd.dtb
+	armada-370-rd.dtb \
+	armada-370-synology-ds213j.dtb
 dtb-$(CONFIG_MACH_ARMADA_375) += \
 	armada-375-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_38X) += \
@@ -507,14 +540,18 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \
 	armada-xp-lenovo-ix4-300d.dtb \
 	armada-xp-matrix.dtb \
 	armada-xp-netgear-rn2120.dtb \
-	armada-xp-openblocks-ax3-4.dtb
+	armada-xp-openblocks-ax3-4.dtb \
+	armada-xp-synology-ds414.dtb
 dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
 	dove-cubox.dtb \
 	dove-cubox-es.dtb \
 	dove-d2plug.dtb \
 	dove-d3plug.dtb \
 	dove-dove-db.dtb
-dtb-$(CONFIG_ARCH_MEDIATEK) += mt6589-aquaris5.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt6589-aquaris5.dtb \
+	mt6592-evb.dtb \
+	mt8127-moose.dtb \
+	mt8135-evbp1.dtb
 
 endif
 

arch/arm/boot/dts/am335x-evm.dts

@@ -307,6 +307,13 @@
 			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
 		>;
 	};
+
+	dcan1_pins_default: dcan1_pins_default {
+		pinctrl-single,pins = <
+			0x168 (PIN_OUTPUT | MUX_MODE2) /* uart0_ctsn.d_can1_tx */
+			0x16c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* uart0_rtsn.d_can1_rx */
+		>;
+	};
 };
 
 &uart0 {
@@ -437,9 +444,9 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&nandflash_pins_s0>;
-	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
 	nand@0,0 {
-		reg = <0 0 0>; /* CS0, offset 0 */
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
 		ti,nand-ecc-opt = "bch8";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -664,3 +671,9 @@
 &aes {
 	status = "okay";
 };
+
+&dcan1 {
+	status = "disabled";	/* Enable only if Profile 1 is selected */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_pins_default>;
+};

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -126,10 +126,10 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&nandflash_pins>;
 
-	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
-		reg = <0 0 0>; /* CS0, offset 0 */
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
 		gpmc,device-width = <1>;

arch/arm/boot/dts/am335x-lxm.dts

+/*
+ * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "NovaTech OrionLXm";
+	compatible = "novatech,am335x-lxm", "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>; /* 512 MB */
+	};
+
+	/* Power supply provides a fixed 5V @2A */
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	/* Power supply provides a fixed 3.3V @3A */
+	vmmcsd_fixed: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+};
+
+&am33xx_pinmux {
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3 */
+			0xf4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat2 */
+			0xf8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat1 */
+			0xfc (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat0 */
+			0x100 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk */
+			0x104 (PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd */
+		>;
+	};
+
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_int */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* rmii1_crs_dv */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* rmii1_rxer */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* rmii1_txen */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* rmii1_td1 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)	/* rmii1_td0 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* rmii1_rd1 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* rmii1_rd0 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* rmii1_refclk */
+
+			/* Slave 2 */
+			0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* rmii2_txen */
+			0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* rmii2_td1 */
+			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* rmii2_td0 */
+			0x68 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* rmii2_rd1 */
+			0x6c (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* rmii2_rd0 */
+			0x70 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* rmii2_crs_dv */
+			0x74 (PIN_INPUT_PULLDOWN | MUX_MODE3)	/* rmii2_rxer */
+			0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_int */
+			0x108 (PIN_INPUT_PULLDOWN | MUX_MODE1)	/* rmii2_refclk */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_int */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_crs_dv */
+			0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_rxer */
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_txen */
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_td1 */
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_td0 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_rd1 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_rd0 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii1_refclk */
+
+			/* Slave 2 reset value*/
+			0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_txen */
+			0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_td1 */
+			0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_td0 */
+			0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_rd1 */
+			0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_rd0 */
+			0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_crs_dv */
+			0x74 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_rxer */
+			0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_int */
+			0x108 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* rmii2_refclk */
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	emmc_pins: pinmux_emmc_pins {
+		pinctrl-single,pins = <
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	serial_config1: serial_config1@20 {
+		compatible = "nxp,pca9539";
+		reg = <0x20>;
+	};
+
+	serial_config2: serial_config2@21 {
+		compatible = "nxp,pca9539";
+		reg = <0x21>;
+	};
+
+	tps: tps@2d {
+		compatible = "ti,tps65910";
+		reg = <0x2d>;
+	};
+};
+
+/include/ "tps65910.dtsi"
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		/* vrtc - unused */
+
+		vio_reg: regulator@1 {
+			regulator-name = "vio_1v5,ddr";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			regulator-name = "vdd1,mpu";
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			regulator-name = "vdd2_1v1,core";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		/* vdd3 - unused */
+
+		/* vdig1 - unused */
+
+		vdig2_reg: regulator@6 {
+			regulator-name = "vdig2_1v8,vdds_pll";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		/* vpll - unused */
+
+		vdac_reg: regulator@8 {
+			regulator-name = "vdac_1v8,vdds";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-name = "vaux1_1v8,usb";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-name = "vaux2_3v3,io";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-name = "vaux33_3v3,usb";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-name = "vmmc_3v3,io";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <5>;
+	phy-mode = "rmii";
+	dual_emac_res_vlan = <2>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <4>;
+	phy-mode = "rmii";
+	dual_emac_res_vlan = <3>;
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac = <1>;
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <8>;
+	ti,non-removable;
+	status = "okay";
+};
+

arch/arm/boot/dts/am33xx.dtsi

@@ -83,6 +83,11 @@
 		};
 	};
 
+	am33xx_control_module: control_module@4a002000 {
+		compatible = "syscon";
+		reg = <0x44e10000 0x7fc>;
+	};
+
 	am33xx_pinmux: pinmux@44e10800 {
 		compatible = "pinctrl-single";
 		reg = <0x44e10800 0x0238>;
@@ -204,6 +209,8 @@
 			reg = <0x44e09000 0x2000>;
 			interrupts = <72>;
 			status = "disabled";
+			dmas = <&edma 26>, <&edma 27>;
+			dma-names = "tx", "rx";
 		};
 
 		uart1: serial@48022000 {
@@ -213,6 +220,8 @@
 			reg = <0x48022000 0x2000>;
 			interrupts = <73>;
 			status = "disabled";
+			dmas = <&edma 28>, <&edma 29>;
+			dma-names = "tx", "rx";
 		};
 
 		uart2: serial@48024000 {
@@ -222,6 +231,8 @@
 			reg = <0x48024000 0x2000>;
 			interrupts = <74>;
 			status = "disabled";
+			dmas = <&edma 30>, <&edma 31>;
+			dma-names = "tx", "rx";
 		};
 
 		uart3: serial@481a6000 {
@@ -333,20 +344,24 @@
 			interrupts = <91>;
 		};
 
-		dcan0: d_can@481cc000 {
-			compatible = "bosch,d_can";
+		dcan0: can@481cc000 {
+			compatible = "ti,am3352-d_can";
 			ti,hwmods = "d_can0";
-			reg = <0x481cc000 0x2000
-				0x44e10644 0x4>;
+			reg = <0x481cc000 0x2000>;
+			clocks = <&dcan0_fck>;
+			clock-names = "fck";
+			syscon-raminit = <&am33xx_control_module 0x644 0>;
 			interrupts = <52>;
 			status = "disabled";
 		};
 
-		dcan1: d_can@481d0000 {
-			compatible = "bosch,d_can";
+		dcan1: can@481d0000 {
+			compatible = "ti,am3352-d_can";
 			ti,hwmods = "d_can1";
-			reg = <0x481d0000 0x2000
-				0x44e10644 0x4>;
+			reg = <0x481d0000 0x2000>;
+			clocks = <&dcan1_fck>;
+			clock-names = "fck";
+			syscon-raminit = <&am33xx_control_module 0x644 1>;
 			interrupts = <55>;
 			status = "disabled";
 		};
@@ -356,6 +371,7 @@
 			reg = <0x480C8000 0x200>;
 			interrupts = <77>;
 			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <8>;
 			mbox_wkupm3: wkup_m3 {

arch/arm/boot/dts/am4372.dtsi

@@ -57,6 +57,11 @@
 		cache-level = <2>;
 	};
 
+	am43xx_control_module: control_module@4a002000 {
+		compatible = "syscon";
+		reg = <0x44e10000 0x7f4>;
+	};
+
 	am43xx_pinmux: pinmux@44e10800 {
 		compatible = "ti,am437-padconf", "pinctrl-single";
 		reg = <0x44e10800 0x31c>;
@@ -168,6 +173,7 @@
 			reg = <0x480C8000 0x200>;
 			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 			ti,hwmods = "mailbox";
+			#mbox-cells = <1>;
 			ti,mbox-num-users = <4>;
 			ti,mbox-num-fifos = <8>;
 			mbox_wkupm3: wkup_m3 {
@@ -667,6 +673,26 @@
 			};
 		};
 
+		tscadc: tscadc@44e0d000 {
+			compatible = "ti,am3359-tscadc";
+			reg = <0x44e0d000 0x1000>;
+			ti,hwmods = "adc_tsc";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&adc_tsc_fck>;
+			clock-names = "fck";
+			status = "disabled";
+
+			tsc {
+				compatible = "ti,am3359-tsc";
+			};
+
+			adc {
+				#io-channel-cells = <1>;
+				compatible = "ti,am3359-adc";
+			};
+
+		};
+
 		sham: sham@53100000 {
 			compatible = "ti,omap5-sham";
 			ti,hwmods = "sham";
@@ -896,6 +922,28 @@
 			compatible = "mmio-sram";
 			reg = <0x40300000 0x40000>; /* 256k */
 		};
+
+		dcan0: can@481cc000 {
+			compatible = "ti,am4372-d_can", "ti,am3352-d_can";
+			ti,hwmods = "d_can0";
+			clocks = <&dcan0_fck>;
+			clock-names = "fck";
+			reg = <0x481cc000 0x2000>;
+			syscon-raminit = <&am43xx_control_module 0x644 0>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		dcan1: can@481d0000 {
+			compatible = "ti,am4372-d_can", "ti,am3352-d_can";
+			ti,hwmods = "d_can1";
+			clocks = <&dcan1_fck>;
+			clock-names = "fck";
+			reg = <0x481d0000 0x2000>;
+			syscon-raminit = <&am43xx_control_module 0x644 1>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -254,6 +254,20 @@
 			0x238 (PIN_OUTPUT_PULLUP | MUX_MODE7)
 		>;
 	};
+
+	dcan0_default: dcan0_default_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_OUTPUT | MUX_MODE2)		/* uart1_ctsn.d_can0_tx */
+			0x17c (PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_rtsn.d_can0_rx */
+		>;
+	};
+
+	dcan1_default: dcan1_default_pins {
+		pinctrl-single,pins = <
+			0x180 (PIN_OUTPUT | MUX_MODE2)		/* uart1_rxd.d_can1_tx */
+			0x184 (PIN_INPUT_PULLUP | MUX_MODE2)	/* uart1_txd.d_can1_rx */
+		>;
+	};
 };
 
 &i2c0 {
@@ -343,6 +357,14 @@
 	status = "okay";
 };
 
+&tscadc {
+	status = "okay";
+
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
 &ecap0 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -511,3 +533,15 @@
 		};
 	};
 };
+
+&dcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan0_default>;
+	status = "okay";
+};
+
+&dcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_default>;
+	status = "okay";
+};

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -438,9 +438,9 @@
 	status = "okay";	/* Disable QSPI when enabling GPMC (NAND) */
 	pinctrl-names = "default";
 	pinctrl-0 = <&nand_flash_x8>;
-	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	ranges = <0 0 0x08000000 0x1000000>;	/* CS0: 16MB for NAND */
 	nand@0,0 {
-		reg = <0 0 0>; /* CS0, offset 0 */
+		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
 		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
@@ -519,6 +519,14 @@
 	status = "okay";
 };
 
+&tscadc {
+	status = "okay";
+
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
 &ecap0 {
 		status = "okay";
 		pinctrl-names = "default";

arch/arm/boot/dts/am57xx-beagle-x15.dts

+/*
+ * Copyright (C) 2014 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "dra74x.dtsi"
+#include <dt-bindings/clk/ti-dra7-atl.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "TI AM5728 BeagleBoard-X15";
+	compatible = "ti,am572x-beagle-x15", "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7";
+
+	aliases {
+		rtc0 = &mcp_rtc;
+		rtc1 = &tps659038_rtc;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	vdd_3v3: fixedregulator-vdd_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		vin-supply = <&regen1>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vtt_fixed: fixedregulator-vtt {
+		/* TPS51200 */
+		compatible = "regulator-fixed";
+		regulator-name = "vtt_fixed";
+		vin-supply = <&smps3_reg>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins_default>;
+
+		led@0 {
+			label = "beagle-x15:usr0";
+			gpios = <&gpio7 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@1 {
+			label = "beagle-x15:usr1";
+			gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "beagle-x15:usr2";
+			gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "beagle-x15:usr3";
+			gpios = <&gpio7 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ide-disk";
+			default-state = "off";
+		};
+	};
+};
+
+&dra7_pmx_core {
+	leds_pins_default: leds_pins_default {
+		pinctrl-single,pins = <
+			0x3a8 (PIN_OUTPUT | MUX_MODE14)	/* spi1_d1.gpio7_8 */
+			0x3ac (PIN_OUTPUT | MUX_MODE14)	/* spi1_d0.gpio7_9 */
+			0x3c0 (PIN_OUTPUT | MUX_MODE14)	/* spi2_sclk.gpio7_14 */
+			0x3c4 (PIN_OUTPUT | MUX_MODE14)	/* spi2_d1.gpio7_15 */
+		>;
+	};
+
+	i2c1_pins_default: i2c1_pins_default {
+		pinctrl-single,pins = <
+			0x400 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_sda.sda */
+			0x404 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c1_scl.scl */
+		>;
+	};
+
+	i2c3_pins_default: i2c3_pins_default {
+		pinctrl-single,pins = <
+			0x2a4 (PIN_INPUT| MUX_MODE10)	/* mcasp1_aclkx.i2c3_sda */
+			0x2a8 (PIN_INPUT| MUX_MODE10)	/* mcasp1_fsx.i2c3_scl */
+		>;
+	};
+
+	uart3_pins_default: uart3_pins_default {
+		pinctrl-single,pins = <
+			0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
+			0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
+		>;
+	};
+
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			0x36c (PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
+			0x354 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			0x358 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			0x35c (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			0x360 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			0x364 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			0x368 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			0x9c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			0xb0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			0xa0 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			0xa4 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			0xa8 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			0xac (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			0x8c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			0x90 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			0x94 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			0x98 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
+
+	tps659038_pins_default: tps659038_pins_default {
+		pinctrl-single,pins = <
+			0x418 (PIN_INPUT_PULLUP | MUX_MODE14)	/* wakeup0.gpio1_0 */
+		>;
+	};
+
+	tmp102_pins_default: tmp102_pins_default {
+		pinctrl-single,pins = <
+			0x3C8 (PIN_INPUT_PULLUP | MUX_MODE14)	/* spi2_d0.gpio7_16 */
+		>;
+	};
+
+	mcp79410_pins_default: mcp79410_pins_default {
+		pinctrl-single,pins = <
+			0x424 (PIN_INPUT_PULLUP | MUX_MODE1)	/* wakeup3.sys_nirq1 */
+		>;
+	};
+
+	usb1_pins: pinmux_usb1_pins {
+		pinctrl-single,pins = <
+			0x280 (PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
+		>;
+	};
+
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	tps659038: tps659038@58 {
+		compatible = "ti,tps659038";
+		reg = <0x58>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tps659038_pins_default>;
+
+		#interrupt-cells = <2>;
+		interrupt-controller;
+
+		ti,system-power-controller;
+
+		tps659038_pmic {
+			compatible = "ti,tps659038-pmic";
+
+			regulators {
+				smps12_reg: smps12 {
+					/* VDD_MPU */
+					regulator-name = "smps12";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps3_reg: smps3 {
+					/* VDD_DDR */
+					regulator-name = "smps3";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps45_reg: smps45 {
+					/* VDD_DSPEVE, VDD_IVA, VDD_GPU */
+					regulator-name = "smps45";
+					regulator-min-microvolt = < 850000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				smps6_reg: smps6 {
+					/* VDD_CORE */
+					regulator-name = "smps6";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1030000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* SMPS7 unused */
+
+				smps8_reg: smps8 {
+					/* VDD_1V8 */
+					regulator-name = "smps8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* SMPS9 unused */
+
+				ldo1_reg: ldo1 {
+					/* VDD_SD  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo2_reg: ldo2 {
+					/* VDD_SHV5 */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo3_reg: ldo3 {
+					/* VDDA_1V8_PHY */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo9_reg: ldo9 {
+					/* VDD_RTC */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldoln_reg: ldoln {
+					/* VDDA_1V8_PLL */
+					regulator-name = "ldoln";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldousb_reg: ldousb {
+					/* VDDA_3V_USB: VDDA_USBHS33 */
+					regulator-name = "ldousb";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				regen1: regen1 {
+					/* VDD_3V3_ON */
+					regulator-name = "regen1";
+					regulator-boot-on;
+					regulator-always-on;
+				};
+			};
+		};
+
+		tps659038_rtc: tps659038_rtc {
+			compatible = "ti,palmas-rtc";
+			interrupt-parent = <&tps659038>;
+			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+		};
+
+		tps659038_pwr_button: tps659038_pwr_button {
+			compatible = "ti,palmas-pwrbutton";
+			interrupt-parent = <&tps659038>;
+			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+			wakeup-source;
+			ti,palmas-long-press-seconds = <12>;
+		};
+	};
+
+	tmp102: tmp102@48 {
+		compatible = "ti,tmp102";
+		reg = <0x48>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tmp102_pins_default>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins_default>;
+	clock-frequency = <400000>;
+
+	mcp_rtc: rtc@6f {
+		compatible = "microchip,mcp7941x";
+		reg = <0x6f>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>;  /* IRQ_SYS_1N */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcp79410_pins_default>;
+
+		vcc-supply = <&vdd_3v3>;
+		wakeup-source;
+	};
+};
+
+&gpio7 {
+	ti,no-reset-on-init;
+	ti,no-idle-on-init;
+};
+
+&cpu0 {
+	cpu0-supply = <&smps12_reg>;
+	voltage-tolerance = <1>;
+};
+
+&uart3 {
+	status = "okay";
+	interrupts-extended = <&gic GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+			      <&dra7_pmx_core 0x248>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins_default>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
+
+	vmmc-supply = <&ldo1_reg>;
+	vmmc_aux-supply = <&vdd_3v3>;
+	pbias-supply = <&pbias_mmc_reg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 27 0>; /* gpio 219 */
+};
+
+&mmc2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_default>;
+
+	vmmc-supply = <&vdd_3v3>;
+	bus-width = <8>;
+	ti,non-removable;
+	cap-mmc-dual-data-rate;
+};
+
+&sata {
+	status = "okay";
+};
+
+&usb2_phy1 {
+	phy-supply = <&ldousb_reg>;
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins>;
+};

arch/arm/boot/dts/arm-realview-pb1176.dts

+/*
+ * Copyright 2014 Linaro Ltd
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "skeleton.dtsi"
+
+/ {
+	model = "ARM RealView PB1176";
+	compatible = "arm,realview-pb1176";
+
+	chosen { };
+
+	aliases {
+		serial0 = &pb1176_serial0;
+		serial1 = &pb1176_serial1;
+		serial2 = &pb1176_serial2;
+		serial3 = &pb1176_serial3;
+		serial4 = &fpga_serial;
+	};
+
+	memory {
+		/* 128 MiB memory @ 0x0 */
+		reg = <0x00000000 0x08000000>;
+	};
+
+	/* The voltage to the MMC card is hardwired at 3.3V */
+	vmmc: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+        };
+
+	xtal24mhz: xtal24mhz@24M {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+	};
+
+	timclk: timclk@1M {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clock-div = <24>;
+		clock-mult = <1>;
+		clocks = <&xtal24mhz>;
+	};
+
+	mclk: mclk@24M {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clock-div = <1>;
+		clock-mult = <1>;
+		clocks = <&xtal24mhz>;
+	};
+
+	kmiclk: kmiclk@24M {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clock-div = <1>;
+		clock-mult = <1>;
+		clocks = <&xtal24mhz>;
+	};
+
+	sspclk: sspclk@24M {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clock-div = <1>;
+		clock-mult = <1>;
+		clocks = <&xtal24mhz>;
+	};
+
+	uartclk: uartclk@24M {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clock-div = <1>;
+		clock-mult = <1>;
+		clocks = <&xtal24mhz>;
+	};
+
+	/* FIXME: this actually hangs off the PLL clocks */
+	pclk: pclk@0 {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <0>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "arm,realview-pb1176-soc", "simple-bus";
+		regmap = <&syscon>;
+		ranges;
+
+		syscon: syscon@10000000 {
+			compatible = "arm,realview-pb1176-syscon", "syscon";
+			reg = <0x10000000 0x1000>;
+
+			led@08.0 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x01>;
+				label = "versatile:0";
+				linux,default-trigger = "heartbeat";
+				default-state = "on";
+			};
+			led@08.1 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x02>;
+				label = "versatile:1";
+				linux,default-trigger = "mmc0";
+				default-state = "off";
+			};
+			led@08.2 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x04>;
+				label = "versatile:2";
+				linux,default-trigger = "cpu0";
+				default-state = "off";
+			};
+			led@08.3 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x08>;
+				label = "versatile:3";
+				default-state = "off";
+			};
+			led@08.4 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x10>;
+				label = "versatile:4";
+				default-state = "off";
+			};
+			led@08.5 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x20>;
+				label = "versatile:5";
+				default-state = "off";
+			};
+			led@08.6 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x40>;
+				label = "versatile:6";
+				default-state = "off";
+			};
+			led@08.7 {
+				compatible = "register-bit-led";
+				offset = <0x08>;
+				mask = <0x80>;
+				label = "versatile:7";
+				default-state = "off";
+			};
+		};
+
+		/* Primary DevChip GIC synthesized with the CPU */
+		intc_dc1176: interrupt-controller@10120000 {
+			compatible = "arm,arm1176jzf-devchip-gic", "arm,arm11mp-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			interrupt-controller;
+			reg = <0x10121000 0x1000>,
+			      <0x10120000 0x100>;
+		};
+
+		L2: l2-cache {
+			compatible = "arm,l220-cache";
+			reg = <0x10110000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>;
+			cache-unified;
+			cache-level = <2>;
+			/*
+			 * Override default cache size, sets and
+			 * associativity as these may be erroneously set
+			 * up by boot loader(s).
+			 */
+			arm,override-auxreg;
+			cache-size = <131072>; // 128kB
+			cache-sets = <512>;
+			cache-line-size = <32>;
+		};
+
+		pmu {
+			compatible = "arm,arm1176-pmu";
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		timer01: timer@10104000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x10104000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, <0 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&timclk>, <&timclk>, <&pclk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+		};
+
+		timer23: timer@10105000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x10105000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>;
+			arm,sp804-has-irq = <1>;
+			clocks = <&timclk>, <&timclk>, <&pclk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+		};
+
+		pb1176_rtc: rtc@10108000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0x10108000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		pb1176_gpio0: gpio@1010a000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x1010a000 0x1000>;
+			gpio-controller;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		pb1176_ssp: ssp@1010b000 {
+			compatible = "arm,pl022", "arm,primecell";
+			reg = <0x1010b000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sspclk>, <&pclk>;
+			clock-names = "SSPCLK", "apb_pclk";
+		};
+
+		pb1176_serial0: serial@1010c000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1010c000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+
+		pb1176_serial1: serial@1010d000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1010d000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+
+		pb1176_serial2: serial@1010e000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1010e000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 20 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+
+		pb1176_serial3: serial@1010f000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1010f000 0x1000>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+	};
+
+	/* These peripherals are inside the FPGA rather than the DevChip */
+	fpga {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges;
+
+		fpga_mci: mmcsd@10005000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			reg = <0x10005000 0x1000>;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 1 IRQ_TYPE_LEVEL_HIGH>,
+					<0 2 IRQ_TYPE_LEVEL_HIGH>;
+			/* Due to frequent FIFO overruns, use just 500 kHz */
+			max-frequency = <500000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			clocks = <&mclk>, <&pclk>;
+			clock-names = "mclk", "apb_pclk";
+			vmmc-supply = <&vmmc>;
+			cd-gpios = <&fpga_gpio1 0 GPIO_ACTIVE_LOW>;
+			wp-gpios = <&fpga_gpio1 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		fpga_kmi0: kmi@10006000 {
+			compatible = "arm,pl050", "arm,primecell";
+			reg = <0x10006000 0x1000>;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&kmiclk>, <&pclk>;
+			clock-names = "KMIREFCLK", "apb_pclk";
+		};
+
+		fpga_kmi1: kmi@10007000 {
+			compatible = "arm,pl050", "arm,primecell";
+			reg = <0x10007000 0x1000>;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&kmiclk>, <&pclk>;
+			clock-names = "KMIREFCLK", "apb_pclk";
+		};
+
+		fpga_charlcd: charlcd@10008000 {
+			compatible = "arm,versatile-lcd";
+			reg = <0x10008000 0x1000>;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		fpga_serial: serial@10009000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x10009000 0x1000>;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&pclk>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+
+		/* This GIC on the board is cascaded off the DevChip GIC */
+		intc_fpga1176: interrupt-controller@10040000 {
+			compatible = "arm,arm1176jzf-devchip-gic", "arm,arm11mp-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			interrupt-controller;
+			reg = <0x10041000 0x1000>,
+			      <0x10040000 0x100>;
+			interrupt-parent = <&intc_dc1176>;
+			interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		fpga_gpio0: gpio@10014000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x10014000 0x1000>;
+			gpio-controller;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		fpga_gpio1: gpio@10015000 {
+			compatible = "arm,pl061", "arm,primecell";
+			reg = <0x10015000 0x1000>;
+			gpio-controller;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+		fpga_rtc: rtc@10017000 {
+			compatible = "arm,pl031", "arm,primecell";
+			reg = <0x10017000 0x1000>;
+			interrupt-parent = <&intc_fpga1176>;
+			interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pclk>;
+			clock-names = "apb_pclk";
+		};
+
+
+	};
+};

arch/arm/boot/dts/armada-370-db.dts

@@ -75,6 +75,7 @@
 				clock-frequency = <100000>;
 				status = "okay";
 				audio_codec: audio-codec@4a {
+					#sound-dai-cells = <0>;
 					compatible = "cirrus,cs42l51";
 					reg = <0x4a>;
 				};
@@ -102,30 +103,6 @@
 				broken-cd;
 			};
 
-			pinctrl {
-				/*
-				 * These pins might be muxed as I2S by
-				 * the bootloader, but it conflicts
-				 * with the real I2S pins that are
-				 * muxed using i2s_pins. We must mux
-				 * those pins to a function other than
-				 * I2S.
-				 */
-				pinctrl-0 = <&hog_pins1 &hog_pins2>;
-				pinctrl-names = "default";
-
-				hog_pins1: hog-pins1 {
-					marvell,pins = "mpp6",  "mpp8", "mpp10",
-						       "mpp12", "mpp13";
-					marvell,function = "gpio";
-				};
-
-				hog_pins2: hog-pins2 {
-					marvell,pins = "mpp5", "mpp7", "mpp9";
-					marvell,function = "gpo";
-				};
-			};
-
 			usb@50000 {
 				status = "okay";
 			};
@@ -135,6 +112,8 @@
 			};
 
 			spi0: spi@10600 {
+				pinctrl-0 = <&spi0_pins2>;
+				pinctrl-names = "default";
 				status = "okay";
 
 				spi-flash@0 {
@@ -167,17 +146,84 @@
 	};
 
 	sound {
-	      compatible = "marvell,a370db-audio";
-	      marvell,audio-controller = <&audio_controller>;
-	      marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>;
-	      status = "okay";
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "Armada 370 DB Audio";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Headphone", "Out Jack",
+			"Line", "In Jack";
+		simple-audio-card,routing =
+			"Out Jack", "HPL",
+			"Out Jack", "HPR",
+			"AIN1L", "In Jack",
+			"AIN1L", "In Jack";
+		status = "okay";
+
+		simple-audio-card,dai-link@0 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 0>;
+			};
+
+			codec {
+				sound-dai = <&audio_codec>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_out>;
+			};
+		};
+
+		simple-audio-card,dai-link@2 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_in>;
+			};
+		};
 	};
 
 	spdif_out: spdif-out {
-	      compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
 	};
 
 	spdif_in: spdif-in {
-	      compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dir";
+	};
+};
+
+&pinctrl {
+	/*
+	 * These pins might be muxed as I2S by
+	 * the bootloader, but it conflicts
+	 * with the real I2S pins that are
+	 * muxed using i2s_pins. We must mux
+	 * those pins to a function other than
+	 * I2S.
+	 */
+	pinctrl-0 = <&hog_pins1 &hog_pins2>;
+	pinctrl-names = "default";
+
+	hog_pins1: hog-pins1 {
+		marvell,pins = "mpp6",  "mpp8", "mpp10",
+			       "mpp12", "mpp13";
+		marvell,function = "gpio";
+	};
+
+	hog_pins2: hog-pins2 {
+		marvell,pins = "mpp5", "mpp7", "mpp9";
+		marvell,function = "gpo";
 	};
 };

arch/arm/boot/dts/armada-370-mirabox.dts

@@ -54,18 +54,6 @@
 				status = "okay";
 			};
 
-			pinctrl {
-				pwr_led_pin: pwr-led-pin {
-					marvell,pins = "mpp63";
-					marvell,function = "gpo";
-				};
-
-				stat_led_pins: stat-led-pins {
-					marvell,pins = "mpp64", "mpp65";
-					marvell,function = "gpio";
-				};
-			};
-
 			gpio_leds {
 				compatible = "gpio-leds";
 				pinctrl-names = "default";
@@ -169,3 +157,16 @@
 		};
 	};
 };
+
+&pinctrl {
+	pwr_led_pin: pwr-led-pin {
+		marvell,pins = "mpp63";
+		marvell,function = "gpo";
+	};
+
+	stat_led_pins: stat-led-pins {
+		marvell,pins = "mpp64", "mpp65";
+		marvell,function = "gpio";
+	};
+};
+

arch/arm/boot/dts/armada-370-netgear-rn102.dts

@@ -35,7 +35,7 @@
 		pcie-controller {
 			status = "okay";
 
-			/* Connected to Marvell SATA controller */
+			/* Connected to Marvell 88SE9170 SATA controller */
 			pcie@1,0 {
 				/* Port 0, Lane 0 */
 				status = "okay";
@@ -53,53 +53,12 @@
 				status = "okay";
 			};
 
+			/* eSATA interface */
 			sata@a0000 {
-				nr-ports = <2>;
+				nr-ports = <1>;
 				status = "okay";
 			};
 
-			pinctrl {
-				power_led_pin: power-led-pin {
-					marvell,pins = "mpp57";
-					marvell,function = "gpio";
-				};
-
-				sata1_led_pin: sata1-led-pin {
-					marvell,pins = "mpp15";
-					marvell,function = "gpio";
-				};
-
-				sata2_led_pin: sata2-led-pin {
-					marvell,pins = "mpp14";
-					marvell,function = "gpio";
-				};
-
-				backup_led_pin: backup-led-pin {
-					marvell,pins = "mpp56";
-					marvell,function = "gpio";
-				};
-
-				backup_button_pin: backup-button-pin {
-					marvell,pins = "mpp58";
-					marvell,function = "gpio";
-				};
-
-				power_button_pin: power-button-pin {
-					marvell,pins = "mpp62";
-					marvell,function = "gpio";
-				};
-
-				reset_button_pin: reset-button-pin {
-					marvell,pins = "mpp6";
-					marvell,function = "gpio";
-				};
-
-				poweroff: poweroff {
-					marvell,pins = "mpp8";
-					marvell,function = "gpio";
-				};
-			};
-
 			mdio {
 				pinctrl-0 = <&mdio_pins>;
 				pinctrl-names = "default";
@@ -204,20 +163,20 @@
 			default-state = "keep";
 		};
 
-		green-sata1-led {
-			label = "rn102:green:sata1";
+		blue-sata1-led {
+			label = "rn102:blue:sata1";
 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		green-sata2-led {
-			label = "rn102:green:sata2";
+		blue-sata2-led {
+			label = "rn102:blue:sata2";
 			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		green-backup-led {
-			label = "rn102:green:backup";
+		blue-backup-led {
+			label = "rn102:blue:backup";
 			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
@@ -256,3 +215,45 @@
 		gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
 	};
 };
+
+&pinctrl {
+	power_led_pin: power-led-pin {
+		marvell,pins = "mpp57";
+		marvell,function = "gpio";
+	};
+
+	sata1_led_pin: sata1-led-pin {
+		marvell,pins = "mpp15";
+		marvell,function = "gpio";
+	};
+
+	sata2_led_pin: sata2-led-pin {
+		marvell,pins = "mpp14";
+		marvell,function = "gpio";
+	};
+
+	backup_led_pin: backup-led-pin {
+		marvell,pins = "mpp56";
+		marvell,function = "gpio";
+	};
+
+	backup_button_pin: backup-button-pin {
+		marvell,pins = "mpp58";
+		marvell,function = "gpio";
+	};
+
+	power_button_pin: power-button-pin {
+		marvell,pins = "mpp62";
+		marvell,function = "gpio";
+	};
+
+	reset_button_pin: reset-button-pin {
+		marvell,pins = "mpp6";
+		marvell,function = "gpio";
+	};
+
+	poweroff: poweroff {
+		marvell,pins = "mpp8";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-370-netgear-rn104.dts

@@ -53,38 +53,6 @@
 				status = "okay";
 			};
 
-			pinctrl {
-				poweroff: poweroff {
-					marvell,pins = "mpp60";
-					marvell,function = "gpio";
-				};
-
-				backup_button_pin: backup-button-pin {
-					marvell,pins = "mpp52";
-					marvell,function = "gpio";
-				};
-
-				power_button_pin: power-button-pin {
-					marvell,pins = "mpp62";
-					marvell,function = "gpio";
-				};
-
-				backup_led_pin: backup-led-pin {
-					marvell,pins = "mpp63";
-					marvell,function = "gpo";
-				};
-
-				power_led_pin: power-led-pin {
-					marvell,pins = "mpp64";
-					marvell,function = "gpio";
-				};
-
-				reset_button_pin: reset-button-pin {
-					marvell,pins = "mpp65";
-					marvell,function = "gpio";
-				};
-			};
-
 			mdio {
 				pinctrl-0 = <&mdio_pins>;
 				pinctrl-names = "default";
@@ -269,3 +237,35 @@
 		gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
 	};
 };
+
+&pinctrl {
+	poweroff: poweroff {
+		marvell,pins = "mpp60";
+		marvell,function = "gpio";
+	};
+
+	backup_button_pin: backup-button-pin {
+		marvell,pins = "mpp52";
+		marvell,function = "gpio";
+	};
+
+	power_button_pin: power-button-pin {
+		marvell,pins = "mpp62";
+		marvell,function = "gpio";
+	};
+
+	backup_led_pin: backup-led-pin {
+		marvell,pins = "mpp63";
+		marvell,function = "gpo";
+	};
+
+	power_led_pin: power-led-pin {
+		marvell,pins = "mpp64";
+		marvell,function = "gpio";
+	};
+
+	reset_button_pin: reset-button-pin {
+		marvell,pins = "mpp65";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-370-rd.dts

@@ -59,18 +59,6 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				fan_pins: fan-pins {
-					marvell,pins = "mpp8";
-					marvell,function = "gpio";
-				};
-
-				led_pins: led-pins {
-					marvell,pins = "mpp32";
-					marvell,function = "gpio";
-				};
-			};
-
 			serial@12000 {
 				status = "okay";
 			};
@@ -85,10 +73,6 @@
 				phy0: ethernet-phy@0 {
 					reg = <0>;
 				};
-
-				phy1: ethernet-phy@1 {
-					reg = <1>;
-				};
 			};
 
 			ethernet@70000 {
@@ -100,8 +84,11 @@
 				pinctrl-0 = <&ge1_rgmii_pins>;
 				pinctrl-names = "default";
 				status = "okay";
-				phy = <&phy1>;
 				phy-mode = "rgmii-id";
+				fixed-link {
+					   speed = <1000>;
+					   full-duplex;
+				};
 			};
 
 			mvsdio@d4000 {
@@ -173,4 +160,56 @@
 			};
 		};
 	};
+
+	dsa@0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth1>;
+		dsa,mii-bus = <&mdio>;
+
+		switch@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x10 0>;	/* MDIO address 16, switch 0 in tree */
+
+			port@0 {
+				reg = <0>;
+				label = "lan0";
+			};
+
+			port@1 {
+			       reg = <1>;
+			       label = "lan1";
+			};
+
+			port@2 {
+			       reg = <2>;
+			       label = "lan2";
+			};
+
+			port@3 {
+			       reg = <3>;
+			       label = "lan3";
+			};
+
+			port@5 {
+			      reg = <5>;
+			      label = "cpu";
+			};
+		};
+	 };
  };
+
+&pinctrl {
+	fan_pins: fan-pins {
+		marvell,pins = "mpp8";
+		marvell,function = "gpio";
+	};
+
+	led_pins: led-pins {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-370-synology-ds213j.dts

+/*
+ * Device Tree file for Synology DS213j
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the old 0xd0000000).
+ * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
+ * bootloaders provided by Marvell. It is used in recent versions of
+ * DSM software provided by Synology. Nonetheless, some earlier boards
+ * were delivered with an older version of u-boot that left internal
+ * registers mapped at 0xd0000000. If you have such a device you will
+ * not be able to directly boot a kernel based on this Device Tree. In
+ * that case, the preferred solution is to update your bootloader (e.g.
+ * by upgrading to latest version of DSM, or building a new one and
+ * installing it from u-boot prompt) or adjust the Devive Tree
+ * (s/0xf1000000/0xd0000000/ in 'ranges' below).
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-370.dtsi"
+
+/ {
+	model = "Synology DS213j";
+	compatible = "synology,ds213j", "marvell,armada370",
+		     "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+
+			/* RTC provided by Seiko S-35390A I2C RTC chip below */
+			rtc@10300 {
+				status = "disabled";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "micron,n25q064";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <20000000>;
+
+					/*
+					 * Warning!
+					 *
+					 * Synology u-boot uses its compiled-in environment
+					 * and it seems Synology did not care to change u-boot
+					 * default configuration in order to allow saving a
+					 * modified environment at a sensible location. So,
+					 * if you do a 'saveenv' under u-boot, your modified
+					 * environment will be saved at 1MB after the start
+					 * of the flash, i.e. in the middle of the uImage.
+					 * For that reason, it is strongly advised not to
+					 * change the default environment, unless you know
+					 * what you are doing.
+					 */
+					partition@00000000 { /* u-boot */
+						label = "RedBoot";
+						reg = <0x00000000 0x000c0000>; /* 768KB */
+					};
+
+					partition@000c0000 { /* uImage */
+						label = "zImage";
+						reg = <0x000c0000 0x002d0000>; /* 2880KB */
+					};
+
+					partition@00390000 { /* uInitramfs */
+						label = "rd.gz";
+						reg = <0x00390000 0x00440000>; /* 4250KB */
+					};
+
+					partition@007d0000 { /* MAC address and serial number */
+						label = "vendor";
+						reg = <0x007d0000 0x00010000>; /* 64KB */
+					};
+
+					partition@007e0000 {
+						label = "RedBoot config";
+						reg = <0x007e0000 0x00010000>; /* 64KB */
+					};
+
+					partition@007f0000 {
+						label = "FIS directory";
+						reg = <0x007f0000 0x00010000>; /* 64KB */
+					};
+				};
+			};
+
+			i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				clock-frequency = <400000>;
+				status = "okay";
+
+				/* Main device RTC chip */
+				s35390a: s35390a@30 {
+					 compatible = "sii,s35390a";
+					 reg = <0x30>;
+				};
+			};
+
+			/* Connected to a header on device's PCB */
+			serial@12000 {
+				status = "okay";
+			};
+
+			/* Connected to a TI MSP430F2111 for power control */
+			serial@12100 {
+				status = "okay";
+			};
+
+			poweroff@12100 {
+				compatible = "synology,power-off";
+				reg = <0x12100 0x100>;
+				clocks = <&coreclk 0>;
+			};
+
+			/* rear USB port, near reset button */
+			usb@50000 {
+				status = "okay";
+			};
+
+			/* rear USB port, near RJ45 port */
+			usb@51000 {
+				status = "okay";
+			};
+
+			mdio {
+				phy1: ethernet-phy@1 { /* Marvell 88E1512 */
+					reg = <1>;
+				};
+			};
+
+			ethernet@70000 {
+			       status = "okay";
+			       phy = <&phy1>;
+			       phy-mode = "sgmii";
+			};
+
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+		};
+	};
+
+	gpio-fan-32-38 {
+		status = "okay";
+		compatible = "gpio-fan";
+		pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin
+			     &fan_ctrl_high_pin &fan_alarm_pin>;
+		pinctrl-names = "default";
+		gpios = <&gpio1 31 GPIO_ACTIVE_HIGH
+			 &gpio2  0 GPIO_ACTIVE_HIGH
+			 &gpio2  1 GPIO_ACTIVE_HIGH>;
+		alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <    0 0
+				       1000 1
+				       1150 2
+				       1350 4
+				       1500 3
+				       1650 5
+				       1750 6
+				       1900 7 >;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&disk1_led_pin
+			     &disk2_led_pin>;
+		pinctrl-names = "default";
+
+		disk1-led-amber {
+			label = "synology:amber:disk1";
+			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+
+		disk2-led-amber {
+			label = "synology:amber:disk2";
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>;
+		pinctrl-names = "default";
+
+		sata1_regulator: sata1-regulator {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <2000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata2_regulator: sata2-regulator {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA2 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <4000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	disk1_led_pin: disk1-led-pin {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+
+	disk2_led_pin: disk2-led-pin {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+
+	sata1_pwr_pin: sata1-pwr-pin {
+		marvell,pins = "mpp37";
+		marvell,function = "gpio";
+	};
+
+	sata2_pwr_pin: sata2-pwr-pin {
+		marvell,pins = "mpp62";
+		marvell,function = "gpio";
+	};
+
+	sata1_pres_pin: sata1-pres-pin {
+		marvell,pins = "mpp60";
+		marvell,function = "gpio";
+	};
+
+	sata2_pres_pin: sata2-pres-pin {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit0_pin: syno-id-bit0-pin {
+		marvell,pins = "mpp55";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit1_pin: syno-id-bit1-pin {
+		marvell,pins = "mpp56";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit2_pin: syno-id-bit2-pin {
+		marvell,pins = "mpp57";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit3_pin: syno-id-bit3-pin {
+		marvell,pins = "mpp58";
+		marvell,function = "gpio";
+	};
+
+	fan_ctrl_low_pin: fan-ctrl-low-pin {
+		marvell,pins = "mpp65";
+		marvell,function = "gpio";
+	};
+
+	fan_ctrl_mid_pin: fan-ctrl-mid-pin {
+		marvell,pins = "mpp64";
+		marvell,function = "gpio";
+	};
+
+	fan_ctrl_high_pin: fan-ctrl-high-pin {
+		marvell,pins = "mpp63";
+		marvell,function = "gpo";
+	};
+
+	fan_alarm_pin: fan-alarm-pin {
+		marvell,pins = "mpp38";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -151,7 +151,7 @@
 				status = "disabled";
 			};
 
-			serial@12000 {
+			uart0: serial@12000 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x12000 0x100>;
 				reg-shift = <2>;
@@ -160,7 +160,8 @@
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
-			serial@12100 {
+
+			uart1: serial@12100 {
 				compatible = "snps,dw-apb-uart";
 				reg = <0x12100 0x100>;
 				reg-shift = <2>;
@@ -170,6 +171,10 @@
 				status = "disabled";
 			};
 
+			pinctrl: pin-ctrl@18000 {
+				reg = <0x18000 0x38>;
+			};
+
 			coredivclk: corediv-clock@18740 {
 				compatible = "marvell,armada-370-corediv-clock";
 				reg = <0x18740 0xc>;
@@ -233,7 +238,7 @@
 				status = "disabled";
 			};
 
-			mdio {
+			mdio: mdio {
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "marvell,orion-mdio";

arch/arm/boot/dts/armada-370.dtsi

@@ -95,81 +95,30 @@
 				compatible = "marvell,aurora-outer-cache";
 				reg = <0x08000 0x1000>;
 				cache-id-part = <0x100>;
+				cache-unified;
 				wt-override;
 			};
 
-			i2c0: i2c@11000 {
-				reg = <0x11000 0x20>;
+			/*
+			 * Default SPI pinctrl setting, can be overwritten on
+			 * board level if a different configuration is used.
+			 */
+			spi0: spi@10600 {
+				pinctrl-0 = <&spi0_pins1>;
+				pinctrl-names = "default";
 			};
 
-			i2c1: i2c@11100 {
-				reg = <0x11100 0x20>;
+			spi1: spi@10680 {
+				pinctrl-0 = <&spi1_pins>;
+				pinctrl-names = "default";
 			};
 
-			system-controller@18200 {
-				compatible = "marvell,armada-370-xp-system-controller";
-				reg = <0x18200 0x100>;
+			i2c0: i2c@11000 {
+				reg = <0x11000 0x20>;
 			};
 
-			pinctrl {
-				compatible = "marvell,mv88f6710-pinctrl";
-				reg = <0x18000 0x38>;
-
-				sdio_pins1: sdio-pins1 {
-					marvell,pins = "mpp9",  "mpp11", "mpp12",
-							"mpp13", "mpp14", "mpp15";
-					marvell,function = "sd0";
-				};
-
-				sdio_pins2: sdio-pins2 {
-					marvell,pins = "mpp47", "mpp48", "mpp49",
-							"mpp50", "mpp51", "mpp52";
-					marvell,function = "sd0";
-				};
-
-				sdio_pins3: sdio-pins3 {
-					marvell,pins = "mpp48", "mpp49", "mpp50",
-							"mpp51", "mpp52", "mpp53";
-					marvell,function = "sd0";
-				};
-
-				i2c0_pins: i2c0-pins {
-					marvell,pins = "mpp2", "mpp3";
-					marvell,function = "i2c0";
-				};
-
-				i2s_pins1: i2s-pins1 {
-					marvell,pins = "mpp5", "mpp6", "mpp7",
-						       "mpp8", "mpp9", "mpp10",
-						       "mpp12", "mpp13";
-					marvell,function = "audio";
-				};
-
-				i2s_pins2: i2s-pins2 {
-					marvell,pins = "mpp49", "mpp47", "mpp50",
-						       "mpp59", "mpp57", "mpp61",
-						       "mpp62", "mpp60", "mpp58";
-					marvell,function = "audio";
-				};
-
-				mdio_pins: mdio-pins {
-					marvell,pins = "mpp17", "mpp18";
-					marvell,function = "ge";
-				};
-
-				ge0_rgmii_pins: ge0-rgmii-pins {
-					marvell,pins = "mpp5", "mpp6", "mpp7", "mpp8",
-						       "mpp9", "mpp10", "mpp11", "mpp12",
-						       "mpp13", "mpp14", "mpp15", "mpp16";
-					marvell,function = "ge0";
-				};
-
-				ge1_rgmii_pins: ge1-rgmii-pins {
-					marvell,pins = "mpp19", "mpp20", "mpp21", "mpp22",
-						       "mpp23", "mpp24", "mpp25", "mpp26",
-						       "mpp27", "mpp28", "mpp29", "mpp30";
-					marvell,function = "ge1";
-				};
+			i2c1: i2c@11100 {
+				reg = <0x11100 0x20>;
 			};
 
 			gpio0: gpio@18100 {
@@ -205,6 +154,26 @@
 				interrupts = <91>;
 			};
 
+			/*
+			 * Default UART pinctrl setting without RTS/CTS, can
+			 * be overwritten on board level if a different
+			 * configuration is used.
+			 */
+			uart0: serial@12000 {
+				pinctrl-0 = <&uart0_pins>;
+				pinctrl-names = "default";
+			};
+
+			uart1: serial@12100 {
+				pinctrl-0 = <&uart1_pins>;
+				pinctrl-names = "default";
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
 			gateclk: clock-gating-control@18220 {
 				compatible = "marvell,armada-370-gating-clock";
 				reg = <0x18220 0x4>;
@@ -249,6 +218,7 @@
 			};
 
 			audio_controller: audio-controller@30000 {
+				#sound-dai-cells = <1>;
 				compatible = "marvell,armada370-audio";
 				reg = <0x30000 0x4000>;
 				interrupts = <93>;
@@ -305,3 +275,91 @@
 		};
 	};
 };
+
+&pinctrl {
+	compatible = "marvell,mv88f6710-pinctrl";
+
+	spi0_pins1: spi0-pins1 {
+		marvell,pins = "mpp33", "mpp34",
+			       "mpp35", "mpp36";
+		marvell,function = "spi0";
+	};
+
+	spi0_pins2: spi0_pins2 {
+		marvell,pins = "mpp32", "mpp63",
+			       "mpp64", "mpp65";
+		marvell,function = "spi0";
+	};
+
+	spi1_pins: spi1-pins {
+		marvell,pins = "mpp49", "mpp50",
+			       "mpp51", "mpp52";
+		marvell,function = "spi1";
+	};
+
+	uart0_pins: uart0-pins {
+		marvell,pins = "mpp0", "mpp1";
+		marvell,function = "uart0";
+	};
+
+	uart1_pins: uart1-pins {
+		marvell,pins = "mpp41", "mpp42";
+		marvell,function = "uart1";
+	};
+
+	sdio_pins1: sdio-pins1 {
+		marvell,pins = "mpp9",  "mpp11", "mpp12",
+				"mpp13", "mpp14", "mpp15";
+		marvell,function = "sd0";
+	};
+
+	sdio_pins2: sdio-pins2 {
+		marvell,pins = "mpp47", "mpp48", "mpp49",
+				"mpp50", "mpp51", "mpp52";
+		marvell,function = "sd0";
+	};
+
+	sdio_pins3: sdio-pins3 {
+		marvell,pins = "mpp48", "mpp49", "mpp50",
+				"mpp51", "mpp52", "mpp53";
+		marvell,function = "sd0";
+	};
+
+	i2c0_pins: i2c0-pins {
+		marvell,pins = "mpp2", "mpp3";
+		marvell,function = "i2c0";
+	};
+
+	i2s_pins1: i2s-pins1 {
+		marvell,pins = "mpp5", "mpp6", "mpp7",
+			       "mpp8", "mpp9", "mpp10",
+			       "mpp12", "mpp13";
+		marvell,function = "audio";
+	};
+
+	i2s_pins2: i2s-pins2 {
+		marvell,pins = "mpp49", "mpp47", "mpp50",
+			       "mpp59", "mpp57", "mpp61",
+			       "mpp62", "mpp60", "mpp58";
+		marvell,function = "audio";
+	};
+
+	mdio_pins: mdio-pins {
+		marvell,pins = "mpp17", "mpp18";
+		marvell,function = "ge";
+	};
+
+	ge0_rgmii_pins: ge0-rgmii-pins {
+		marvell,pins = "mpp5", "mpp6", "mpp7", "mpp8",
+			       "mpp9", "mpp10", "mpp11", "mpp12",
+			       "mpp13", "mpp14", "mpp15", "mpp16";
+		marvell,function = "ge0";
+	};
+
+	ge1_rgmii_pins: ge1-rgmii-pins {
+		marvell,pins = "mpp19", "mpp20", "mpp21", "mpp22",
+			       "mpp23", "mpp24", "mpp25", "mpp26",
+			       "mpp27", "mpp28", "mpp29", "mpp30";
+		marvell,function = "ge1";
+	};
+};

arch/arm/boot/dts/armada-375.dtsi

@@ -36,6 +36,12 @@
 			#clock-cells = <0>;
 			clock-frequency = <2000000000>;
 		};
+		/* 25 MHz reference crystal */
+		refclk: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
 	};
 
 	cpus {
@@ -366,13 +372,15 @@
 						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 						      <&mpic 5>,
 						      <&mpic 6>;
-				clocks = <&coreclk 0>;
+				clocks = <&coreclk 0>, <&refclk>;
+				clock-names = "nbclk", "fixed";
 			};
 
 			watchdog@20300 {
 				compatible = "marvell,armada-375-wdt";
 				reg = <0x20300 0x34>, <0x20704 0x4>, <0x18254 0x4>;
-				clocks = <&coreclk 0>;
+				clocks = <&coreclk 0>, <&refclk>;
+				clock-names = "nbclk", "fixed";
 			};
 
 			cpurst@20800 {

arch/arm/boot/dts/armada-385-db.dts

@@ -116,11 +116,11 @@
 			};
 
 			sdhci@d8000 {
-				clock-frequency = <200000000>;
 				broken-cd;
 				wp-inverted;
 				bus-width = <8>;
 				status = "okay";
+				no-1-8-v;
 			};
 
 			usb3@f0000 {

arch/arm/boot/dts/armada-38x.dtsi

@@ -25,9 +25,9 @@
 	aliases {
 		gpio0 = &gpio0;
 		gpio1 = &gpio1;
-		eth0 = &eth0;
-		eth1 = &eth1;
-		eth2 = &eth2;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
 	};
 
 	soc {

arch/arm/boot/dts/armada-xp-axpwifiap.dts

@@ -60,40 +60,6 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				pinctrl-0 = <&pmx_phy_int>;
-				pinctrl-names = "default";
-
-				pmx_ge0: pmx-ge0 {
-					marvell,pins = "mpp0", "mpp1", "mpp2", "mpp3",
-						       "mpp4", "mpp5", "mpp6", "mpp7",
-						       "mpp8", "mpp9", "mpp10", "mpp11";
-					marvell,function = "ge0";
-				};
-
-				pmx_ge1: pmx-ge1 {
-					marvell,pins = "mpp12", "mpp13", "mpp14", "mpp15",
-						       "mpp16", "mpp17", "mpp18", "mpp19",
-						       "mpp20", "mpp21", "mpp22", "mpp23";
-					marvell,function = "ge1";
-				};
-
-				pmx_keys: pmx-keys {
-					marvell,pins = "mpp33";
-					marvell,function = "gpio";
-				};
-
-				pmx_spi: pmx-spi {
-					marvell,pins = "mpp36", "mpp37", "mpp38", "mpp39";
-					marvell,function = "spi";
-				};
-
-				pmx_phy_int: pmx-phy-int {
-					marvell,pins = "mpp32";
-					marvell,function = "gpio";
-				};
-			};
-
 			serial@12000 {
 				status = "okay";
 			};
@@ -118,14 +84,14 @@
 			};
 
 			ethernet@70000 {
-				pinctrl-0 = <&pmx_ge0>;
+				pinctrl-0 = <&ge0_rgmii_pins>;
 				pinctrl-names = "default";
 				status = "okay";
 				phy = <&phy0>;
 				phy-mode = "rgmii-id";
 			};
 			ethernet@74000 {
-				pinctrl-0 = <&pmx_ge1>;
+				pinctrl-0 = <&ge1_rgmii_pins>;
 				pinctrl-names = "default";
 				status = "okay";
 				phy = <&phy1>;
@@ -134,8 +100,6 @@
 
 			spi0: spi@10600 {
 				status = "okay";
-				pinctrl-0 = <&pmx_spi>;
-				pinctrl-names = "default";
 
 				spi-flash@0 {
 					#address-cells = <1>;
@@ -152,7 +116,7 @@
 		compatible = "gpio-keys";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		pinctrl-0 = <&pmx_keys>;
+		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
 		button@1 {
@@ -162,3 +126,18 @@
 		};
 	};
 };
+
+&pinctrl {
+	pinctrl-0 = <&phy_int_pin>;
+	pinctrl-names = "default";
+
+	keys_pin: keys-pin {
+		marvell,pins = "mpp33";
+		marvell,function = "gpio";
+	};
+
+	phy_int_pin: phy-int-pin {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts

@@ -22,7 +22,7 @@
 
 	chosen {
 		bootargs = "console=ttyS0,115200 earlyprintk";
-		stdout-path = "/soc/internal-regs/serial@12000";
+		stdout-path = &uart0;
 	};
 
 	memory {
@@ -51,37 +51,6 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				poweroff_pin: poweroff-pin {
-					marvell,pins = "mpp24";
-					marvell,function = "gpio";
-				};
-
-				power_button_pin: power-button-pin {
-					marvell,pins = "mpp44";
-					marvell,function = "gpio";
-				};
-
-				reset_button_pin: reset-button-pin {
-					marvell,pins = "mpp45";
-					marvell,function = "gpio";
-				};
-				select_button_pin: select-button-pin {
-					marvell,pins = "mpp41";
-					marvell,function = "gpio";
-				};
-
-				scroll_button_pin: scroll-button-pin {
-					marvell,pins = "mpp42";
-					marvell,function = "gpio";
-				};
-
-				hdd_led_pin: hdd-led-pin {
-					marvell,pins = "mpp26";
-					marvell,function = "gpio";
-				};
-			};
-
 			serial@12000 {
 				status = "okay";
 			};
@@ -97,12 +66,16 @@
 			};
 
 			ethernet@70000 {
+				pinctrl-0 = <&ge0_rgmii_pins>;
+				pinctrl-names = "default";
 				status = "okay";
 				phy = <&phy0>;
 				phy-mode = "rgmii-id";
 			};
 
 			ethernet@74000 {
+				pinctrl-0 = <&ge1_rgmii_pins>;
+				pinctrl-names = "default";
 				status = "okay";
 				phy = <&phy1>;
 				phy-mode = "rgmii-id";
@@ -125,6 +98,11 @@
 					reg = <0x2e>;
 				};
 
+				eeprom@50 {
+					compatible = "atmel,24c64";
+					reg = <0x50>;
+				};
+
 				pcf8563@51 {
 					compatible = "nxp,pcf8563";
 					reg = <0x51>;
@@ -226,7 +204,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			reg = <0>;
-			registers-number = <2>;
+			registers-number = <1>;
 			spi-max-frequency = <100000>;
 		};
 	};
@@ -282,3 +260,34 @@
 		gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
 	};
 };
+
+&pinctrl {
+	poweroff_pin: poweroff-pin {
+		marvell,pins = "mpp24";
+		marvell,function = "gpio";
+	};
+
+	power_button_pin: power-button-pin {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	reset_button_pin: reset-button-pin {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+	select_button_pin: select-button-pin {
+		marvell,pins = "mpp41";
+		marvell,function = "gpio";
+	};
+
+	scroll_button_pin: scroll-button-pin {
+		marvell,pins = "mpp42";
+		marvell,function = "gpio";
+	};
+
+	hdd_led_pin: hdd-led-pin {
+		marvell,pins = "mpp26";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-xp-mv78230.dtsi

@@ -167,17 +167,6 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				compatible = "marvell,mv78230-pinctrl";
-				reg = <0x18000 0x38>;
-
-				sdio_pins: sdio-pins {
-					marvell,pins = "mpp30", "mpp31", "mpp32",
-						       "mpp33", "mpp34", "mpp35";
-					marvell,function = "sd0";
-				};
-			};
-
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
 				reg = <0x18100 0x40>;
@@ -202,3 +191,7 @@
 		};
 	};
 };
+
+&pinctrl {
+	compatible = "marvell,mv78230-pinctrl";
+};

arch/arm/boot/dts/armada-xp-mv78260.dtsi

@@ -251,17 +251,6 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				compatible = "marvell,mv78260-pinctrl";
-				reg = <0x18000 0x38>;
-
-				sdio_pins: sdio-pins {
-					marvell,pins = "mpp30", "mpp31", "mpp32",
-						       "mpp33", "mpp34", "mpp35";
-					marvell,function = "sd0";
-				};
-			};
-
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
 				reg = <0x18100 0x40>;
@@ -305,3 +294,7 @@
 		};
 	};
 };
+
+&pinctrl {
+	compatible = "marvell,mv78260-pinctrl";
+};

arch/arm/boot/dts/armada-xp-mv78460.dtsi

@@ -289,17 +289,6 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				compatible = "marvell,mv78460-pinctrl";
-				reg = <0x18000 0x38>;
-
-				sdio_pins: sdio-pins {
-					marvell,pins = "mpp30", "mpp31", "mpp32",
-						       "mpp33", "mpp34", "mpp35";
-					marvell,function = "sd0";
-				};
-			};
-
 			gpio0: gpio@18100 {
 				compatible = "marvell,orion-gpio";
 				reg = <0x18100 0x40>;
@@ -343,3 +332,7 @@
 		};
 	};
 };
+
+&pinctrl {
+	compatible = "marvell,mv78460-pinctrl";
+};

arch/arm/boot/dts/armada-xp-netgear-rn2120.dts

@@ -55,86 +55,10 @@
 		};
 
 		internal-regs {
-			pinctrl {
-				poweroff: poweroff {
-					marvell,pins = "mpp42";
-					marvell,function = "gpio";
-				};
-
-				power_button_pin: power-button-pin {
-					marvell,pins = "mpp27";
-					marvell,function = "gpio";
-				};
-
-				reset_button_pin: reset-button-pin {
-					marvell,pins = "mpp41";
-					marvell,function = "gpio";
-				};
-
-				sata1_led_pin: sata1-led-pin {
-					marvell,pins = "mpp31";
-					marvell,function = "gpio";
-				};
-
-				sata2_led_pin: sata2-led-pin {
-					marvell,pins = "mpp40";
-					marvell,function = "gpio";
-				};
-
-				sata3_led_pin: sata3-led-pin {
-					marvell,pins = "mpp44";
-					marvell,function = "gpio";
-				};
-
-				sata4_led_pin: sata4-led-pin {
-					marvell,pins = "mpp47";
-					marvell,function = "gpio";
-				};
-
-				sata1_power_pin: sata1-power-pin {
-					marvell,pins = "mpp24";
-					marvell,function = "gpio";
-				};
-
-				sata2_power_pin: sata2-power-pin {
-					marvell,pins = "mpp25";
-					marvell,function = "gpio";
-				};
-
-				sata3_power_pin: sata3-power-pin {
-					marvell,pins = "mpp26";
-					marvell,function = "gpio";
-				};
-
-				sata4_power_pin: sata4-power-pin {
-					marvell,pins = "mpp28";
-					marvell,function = "gpio";
-				};
-
-				sata1_pres_pin: sata1-pres-pin {
-					marvell,pins = "mpp32";
-					marvell,function = "gpio";
-				};
-
-				sata2_pres_pin: sata2-pres-pin {
-					marvell,pins = "mpp33";
-					marvell,function = "gpio";
-				};
-
-				sata3_pres_pin: sata3-pres-pin {
-					marvell,pins = "mpp34";
-					marvell,function = "gpio";
-				};
-
-				sata4_pres_pin: sata4-pres-pin {
-					marvell,pins = "mpp35";
-					marvell,function = "gpio";
-				};
-
-				err_led_pin: err-led-pin {
-					marvell,pins = "mpp45";
-					marvell,function = "gpio";
-				};
+			/* Two rear eSATA ports */
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
 			};
 
 			serial@12000 {
@@ -328,3 +252,85 @@
 		gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
 	};
 };
+
+&pinctrl {
+	poweroff: poweroff {
+		marvell,pins = "mpp42";
+		marvell,function = "gpio";
+	};
+
+	power_button_pin: power-button-pin {
+		marvell,pins = "mpp27";
+		marvell,function = "gpio";
+	};
+
+	reset_button_pin: reset-button-pin {
+		marvell,pins = "mpp41";
+		marvell,function = "gpio";
+	};
+
+	sata1_led_pin: sata1-led-pin {
+		marvell,pins = "mpp31";
+		marvell,function = "gpio";
+	};
+
+	sata2_led_pin: sata2-led-pin {
+		marvell,pins = "mpp40";
+		marvell,function = "gpio";
+	};
+
+	sata3_led_pin: sata3-led-pin {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	sata4_led_pin: sata4-led-pin {
+		marvell,pins = "mpp47";
+		marvell,function = "gpio";
+	};
+
+	sata1_power_pin: sata1-power-pin {
+		marvell,pins = "mpp24";
+		marvell,function = "gpio";
+	};
+
+	sata2_power_pin: sata2-power-pin {
+		marvell,pins = "mpp25";
+		marvell,function = "gpio";
+	};
+
+	sata3_power_pin: sata3-power-pin {
+		marvell,pins = "mpp26";
+		marvell,function = "gpio";
+	};
+
+	sata4_power_pin: sata4-power-pin {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	sata1_pres_pin: sata1-pres-pin {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+
+	sata2_pres_pin: sata2-pres-pin {
+		marvell,pins = "mpp33";
+		marvell,function = "gpio";
+	};
+
+	sata3_pres_pin: sata3-pres-pin {
+		marvell,pins = "mpp34";
+		marvell,function = "gpio";
+	};
+
+	sata4_pres_pin: sata4-pres-pin {
+		marvell,pins = "mpp35";
+		marvell,function = "gpio";
+	};
+
+	err_led_pin: err-led-pin {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -77,12 +77,7 @@
 			serial@12100 {
 				status = "okay";
 			};
-			pinctrl {
-				led_pins: led-pins-0 {
-					marvell,pins = "mpp49", "mpp51", "mpp53";
-					marvell,function = "gpio";
-				};
-			};
+
 			leds {
 				compatible = "gpio-leds";
 				pinctrl-names = "default";
@@ -187,3 +182,10 @@
 		};
 	};
 };
+
+&pinctrl {
+	led_pins: led-pins-0 {
+		marvell,pins = "mpp49", "mpp51", "mpp53";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-xp-synology-ds414.dts

+/*
+ * Device Tree file for Synology DS414
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the old 0xd0000000).
+ * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
+ * bootloaders provided by Marvell. It is used in recent versions of
+ * DSM software provided by Synology. Nonetheless, some earlier boards
+ * were delivered with an older version of u-boot that left internal
+ * registers mapped at 0xd0000000. If you have such a device you will
+ * not be able to directly boot a kernel based on this Device Tree. In
+ * that case, the preferred solution is to update your bootloader (e.g.
+ * by upgrading to latest version of DSM, or building a new one and
+ * installing it from u-boot prompt) or adjust the Devive Tree
+ * (s/0xf1000000/0xd0000000/ in 'ranges' below).
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78230.dtsi"
+
+/ {
+	model = "Synology DS414";
+	compatible = "synology,ds414", "marvell,armadaxp-mv78230",
+		     "marvell,armadaxp", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x40000000>; /* 1GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>;
+
+		pcie-controller {
+			status = "okay";
+
+			/*
+			 * Connected to Marvell 88SX7042 SATA-II controller
+			 * handling the four disks.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			/*
+			 * Connected to EtronTech EJ168A XHCI controller
+			 * providing the two rear USB 3.0 ports.
+			 */
+			pcie@5,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+
+			/* RTC is provided by Seiko S-35390A below */
+			rtc@10300 {
+				status = "disabled";
+			};
+
+			spi0: spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "micron,n25q064";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <20000000>;
+
+					/*
+					 * Warning!
+					 *
+					 * Synology u-boot uses its compiled-in environment
+					 * and it seems Synology did not care to change u-boot
+					 * default configuration in order to allow saving a
+					 * modified environment at a sensible location. So,
+					 * if you do a 'saveenv' under u-boot, your modified
+					 * environment will be saved at 1MB after the start
+					 * of the flash, i.e. in the middle of the uImage.
+					 * For that reason, it is strongly advised not to
+					 * change the default environment, unless you know
+					 * what you are doing.
+					 */
+					partition@00000000 { /* u-boot */
+						label = "RedBoot";
+						reg = <0x00000000 0x000d0000>; /* 832KB */
+					};
+
+					partition@000c0000 { /* uImage */
+						label = "zImage";
+						reg = <0x000d0000 0x002d0000>; /* 2880KB */
+					};
+
+					partition@003a0000 { /* uInitramfs */
+						label = "rd.gz";
+						reg = <0x003a0000 0x00430000>; /* 4250KB */
+					};
+
+					partition@007d0000 { /* MAC address and serial number */
+						label = "vendor";
+						reg = <0x007d0000 0x00010000>; /* 64KB */
+					};
+
+					partition@007e0000 {
+						label = "RedBoot config";
+						reg = <0x007e0000 0x00010000>; /* 64KB */
+					};
+
+					partition@007f0000 {
+						label = "FIS directory";
+						reg = <0x007f0000 0x00010000>; /* 64KB */
+					};
+				};
+			};
+
+			i2c@11000 {
+				clock-frequency = <400000>;
+				status = "okay";
+
+				s35390a: s35390a@30 {
+					 compatible = "sii,s35390a";
+					 reg = <0x30>;
+				};
+			};
+
+			/* Connected to a header on device's PCB. This
+			 * provides the main console for the device.
+			 *
+			 * Warning: the device may not boot with a 3.3V
+			 * USB-serial converter connected when the power
+			 * button is pressed. The converter needs to be
+			 * connected a few seconds after pressing the
+			 * power button. This is possibly due to UART0_TXD
+			 * pin being sampled at reset (bit 0 of SAR).
+			 */
+			serial@12000 {
+				status = "okay";
+			};
+
+			/* Connected to a Microchip PIC16F883 for power control */
+			serial@12100 {
+				status = "okay";
+			};
+
+			poweroff@12100 {
+				compatible = "synology,power-off";
+				reg = <0x12100 0x100>;
+				clocks = <&coreclk 0>;
+			};
+
+			/* Front USB 2.0 port */
+			usb@50000 {
+				status = "okay";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 { /* Marvell 88E1512 */
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 { /* Marvell 88E1512 */
+					reg = <1>;
+				};
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				pinctrl-0 = <&ge0_rgmii_pins>;
+				pinctrl-names = "default";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@74000 {
+				pinctrl-0 = <&ge1_rgmii_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
+			     &sata3_pwr_pin &sata4_pwr_pin>;
+		pinctrl-names = "default";
+
+		sata1_regulator: sata1-regulator {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <2000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata2_regulator: sata2-regulator {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA2 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <4000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata3_regulator: sata3-regulator {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "SATA3 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <6000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata4_regulator: sata4-regulator {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "SATA4 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <8000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	sata1_pwr_pin: sata1-pwr-pin {
+		marvell,pins = "mpp42";
+		marvell,function = "gpio";
+	};
+
+	sata2_pwr_pin: sata2-pwr-pin {
+		marvell,pins = "mpp44";
+		marvell,function = "gpio";
+	};
+
+	sata3_pwr_pin: sata3-pwr-pin {
+		marvell,pins = "mpp45";
+		marvell,function = "gpio";
+	};
+
+	sata4_pwr_pin: sata4-pwr-pin {
+		marvell,pins = "mpp46";
+		marvell,function = "gpio";
+	};
+
+	sata1_pres_pin: sata1-pres-pin {
+		marvell,pins = "mpp34";
+		marvell,function = "gpio";
+	};
+
+	sata2_pres_pin: sata2-pres-pin {
+		marvell,pins = "mpp35";
+		marvell,function = "gpio";
+	};
+
+	sata3_pres_pin: sata3-pres-pin {
+		marvell,pins = "mpp40";
+		marvell,function = "gpio";
+	};
+
+	sata4_pres_pin: sata4-pres-pin {
+		marvell,pins = "mpp41";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit0_pin: syno-id-bit0-pin {
+		marvell,pins = "mpp26";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit1_pin: syno-id-bit1-pin {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	syno_id_bit2_pin: syno-id-bit2-pin {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	fan1_alarm_pin: fan1-alarm-pin {
+		marvell,pins = "mpp33";
+		marvell,function = "gpio";
+	};
+
+	fan2_alarm_pin: fan2-alarm-pin {
+		marvell,pins = "mpp32";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-xp.dtsi

@@ -44,9 +44,15 @@
 				compatible = "marvell,aurora-system-cache";
 				reg = <0x08000 0x1000>;
 				cache-id-part = <0x100>;
+				cache-unified;
 				wt-override;
 			};
 
+			spi0: spi@10600 {
+				pinctrl-0 = <&spi0_pins>;
+				pinctrl-names = "default";
+			};
+
 			i2c0: i2c@11000 {
 				compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
 				reg = <0x11000 0x100>;
@@ -57,8 +63,10 @@
 				reg = <0x11100 0x100>;
 			};
 
-			serial@12200 {
+			uart2: serial@12200 {
 				compatible = "snps,dw-apb-uart";
+				pinctrl-0 = <&uart2_pins>;
+				pinctrl-names = "default";
 				reg = <0x12200 0x100>;
 				reg-shift = <2>;
 				interrupts = <43>;
@@ -66,8 +74,11 @@
 				clocks = <&coreclk 0>;
 				status = "disabled";
 			};
-			serial@12300 {
+
+			uart3: serial@12300 {
 				compatible = "snps,dw-apb-uart";
+				pinctrl-0 = <&uart3_pins>;
+				pinctrl-names = "default";
 				reg = <0x12300 0x100>;
 				reg-shift = <2>;
 				interrupts = <44>;
@@ -204,3 +215,54 @@
 		};
 	};
 };
+
+&pinctrl {
+	ge0_gmii_pins: ge0-gmii-pins {
+		marvell,pins =
+		     "mpp0",  "mpp1",  "mpp2",  "mpp3",
+		     "mpp4",  "mpp5",  "mpp6",  "mpp7",
+		     "mpp8",  "mpp9",  "mpp10", "mpp11",
+		     "mpp12", "mpp13", "mpp14", "mpp15",
+		     "mpp16", "mpp17", "mpp18", "mpp19",
+		     "mpp20", "mpp21", "mpp22", "mpp23";
+		marvell,function = "ge0";
+	};
+
+	ge0_rgmii_pins: ge0-rgmii-pins {
+		marvell,pins =
+		     "mpp0", "mpp1", "mpp2", "mpp3",
+		     "mpp4", "mpp5", "mpp6", "mpp7",
+		     "mpp8", "mpp9", "mpp10", "mpp11";
+		marvell,function = "ge0";
+	};
+
+	ge1_rgmii_pins: ge1-rgmii-pins {
+		marvell,pins =
+		     "mpp12", "mpp13", "mpp14", "mpp15",
+		     "mpp16", "mpp17", "mpp18", "mpp19",
+		     "mpp20", "mpp21", "mpp22", "mpp23";
+		marvell,function = "ge1";
+	};
+
+	sdio_pins: sdio-pins {
+		marvell,pins = "mpp30", "mpp31", "mpp32",
+			       "mpp33", "mpp34", "mpp35";
+		marvell,function = "sd0";
+	};
+
+	spi0_pins: spi0-pins {
+		marvell,pins = "mpp36", "mpp37",
+			       "mpp38", "mpp39";
+		marvell,function = "spi";
+	};
+
+	uart2_pins: uart2-pins {
+		marvell,pins = "mpp42", "mpp43";
+		marvell,function = "uart2";
+	};
+
+	uart3_pins: uart3-pins {
+		marvell,pins = "mpp44", "mpp45";
+		marvell,function = "uart3";
+	};
+};

arch/arm/boot/dts/at91sam9263.dtsi

@@ -677,6 +677,14 @@
 					};
 				};
 
+				can {
+					pinctrl_can_rx_tx: can_rx_tx {
+						atmel,pins =
+							<AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE	/* CANRX, conflicts with IRQ0 */
+							 AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* CANTX, conflicts with PCK0 */
+					};
+				};
+
 				pioA: gpio@fffff200 {
 					compatible = "atmel,at91rm9200-gpio";
 					reg = <0xfffff200 0x200>;
@@ -905,6 +913,17 @@
 				clock-names = "pwm_clk";
 				status = "disabled";
 			};
+
+			can: can@fffac000 {
+				compatible = "atmel,at91sam9263-can";
+				reg = <0xfffac000 0x300>;
+				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 3>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can_rx_tx>;
+				clocks = <&can_clk>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
 		};
 
 		fb0: fb@0x00700000 {

arch/arm/boot/dts/at91sam9x25.dtsi

@@ -10,6 +10,7 @@
 #include "at91sam9x5_usart3.dtsi"
 #include "at91sam9x5_macb0.dtsi"
 #include "at91sam9x5_macb1.dtsi"
+#include "at91sam9x5_can.dtsi"
 
 / {
 	model = "Atmel AT91SAM9X25 SoC";

arch/arm/boot/dts/at91sam9x35.dtsi

@@ -8,6 +8,7 @@
 
 #include "at91sam9x5.dtsi"
 #include "at91sam9x5_macb0.dtsi"
+#include "at91sam9x5_can.dtsi"
 
 / {
 	model = "Atmel AT91SAM9X35 SoC";

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -860,6 +860,9 @@
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
+				dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(8)>,
+				       <&dma1 1 (AT91_DMA_CFG_PER_ID(9) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+				dma-names = "tx", "rx";
 				clocks = <&mck>;
 				clock-names = "usart";
 				status = "disabled";
@@ -871,6 +874,9 @@
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
+				dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(3)>,
+				       <&dma0 1 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+				dma-names = "tx", "rx";
 				clocks = <&usart0_clk>;
 				clock-names = "usart";
 				status = "disabled";
@@ -882,6 +888,9 @@
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
+				dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(5)>,
+				       <&dma0 1 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+				dma-names = "tx", "rx";
 				clocks = <&usart1_clk>;
 				clock-names = "usart";
 				status = "disabled";
@@ -893,6 +902,9 @@
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
+				dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(12)>,
+				       <&dma1 1 (AT91_DMA_CFG_PER_ID(13) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+				dma-names = "tx", "rx";
 				clocks = <&usart2_clk>;
 				clock-names = "usart";
 				status = "disabled";

arch/arm/boot/dts/at91sam9x5_can.dtsi

 /*
- * at91sam9x5_macb0.dtsi - Device Tree Include file for AT91SAM9x5 SoC with 1
+ * at91sam9x5_can.dtsi - Device Tree Include file for AT91SAM9x5 SoC with 1
  * Ethernet interface.
  *
  * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
@@ -20,10 +20,50 @@
 						reg = <29>;
 					};
 
-                                        can1_clk: can1_clk {
-                                                #clock-cells = <0>;
-                                                reg = <30>;
-                                        };
+					can1_clk: can1_clk {
+						#clock-cells = <0>;
+						reg = <30>;
+					};
+				};
+			};
+
+			can0: can@f8000000 {
+				compatible = "atmel,at91sam9x5-can";
+				reg = <0xf8000000 0x300>;
+				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 3>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can0_rx_tx>;
+				clocks = <&can0_clk>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
+
+			can1: can@f8004000 {
+				compatible = "atmel,at91sam9x5-can";
+				reg = <0xf8004000 0x300>;
+				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 3>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can1_rx_tx>;
+				clocks = <&can1_clk>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
+
+			pinctrl@fffff400 {
+				can0 {
+					pinctrl_can0_rx_tx: can0_rx_tx {
+						atmel,pins =
+							<AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX0, conflicts with DRXD */
+							AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* CANTX0, conflicts with DTXD */
+					};
+				};
+
+				can1 {
+					pinctrl_can1_rx_tx: can1_rx_tx {
+						atmel,pins =
+							<AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX1, conflicts with RXD1 */
+							AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* CANTX1, conflicts with TXD1 */
+					};
 				};
 			};
 		};

arch/arm/boot/dts/at91sam9x5_usart3.dtsi

@@ -57,6 +57,9 @@
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
+				dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(14)>,
+				       <&dma1 1 (AT91_DMA_CFG_PER_ID(15) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+				dma-names = "tx", "rx";
 				clocks = <&usart3_clk>;
 				clock-names = "usart";
 				status = "disabled";

arch/arm/boot/dts/atlas6.dtsi

@@ -131,6 +131,7 @@
 				reg = <0x90020000 0x10000>;
 				interrupts = <31>;
 				clocks = <&clks 35>;
+				resets = <&rstc 6>;
 			};
 		};
 
@@ -312,6 +313,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&clks 19>;
+				resets = <&rstc 26>;
 				status = "disabled";
 			};
 
@@ -327,6 +329,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				clocks = <&clks 20>;
+				resets = <&rstc 27>;
 				status = "disabled";
 			};
 
@@ -522,6 +525,18 @@
                                                 sirf,function = "sdmmc5";
                                         };
                                 };
+				i2s_mclk_pins_a: i2s_mclk@0 {
+                                        i2s_mclk {
+                                                sirf,pins = "i2smclkgrp";
+                                                sirf,function = "i2s_mclk";
+                                        };
+                                };
+				i2s_ext_clk_input_pins_a: i2s_ext_clk_input@0 {
+                                        i2s_ext_clk_input {
+                                                sirf,pins = "i2s_ext_clk_inputgrp";
+                                                sirf,function = "i2s_ext_clk_input";
+                                        };
+                                };
                                 i2s_pins_a: i2s@0 {
                                         i2s {
                                                 sirf,pins = "i2sgrp";

arch/arm/boot/dts/bcm-cygnus-clock.dtsi

+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+clocks {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	osc: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <1>;
+		clock-frequency = <25000000>;
+	};
+
+	apb_clk: apb_clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1000000000>;
+	};
+
+	periph_clk: periph_clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <500000000>;
+	};
+
+	sdio_clk: lcpll_ch2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <200000000>;
+	};
+
+	axi81_clk: axi81_clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	keypad_clk: keypad_clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <31806>;
+	};
+
+	adc_clk: adc_clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1562500>;
+	};
+
+	pwm_clk: pwm_clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <1000000>;
+	};
+
+	lcd_clk: mipipll_ch1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+};

arch/arm/boot/dts/bcm-cygnus.dtsi

+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2014 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	compatible = "brcm,cygnus";
+	model = "Broadcom Cygnus SoC";
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+	};
+
+	/include/ "bcm-cygnus-clock.dtsi"
+
+	amba {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "arm,amba-bus", "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		wdt@18009000 {
+			 compatible = "arm,sp805" , "arm,primecell";
+			 reg = <0x18009000 0x1000>;
+			 interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			 clocks = <&axi81_clk>;
+			 clock-names = "apb_pclk";
+		};
+	};
+
+	uart0: serial@18020000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x18020000 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&axi81_clk>;
+		clock-frequency = <100000000>;
+		status = "disabled";
+	};
+
+	uart1: serial@18021000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x18021000 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&axi81_clk>;
+		clock-frequency = <100000000>;
+		status = "disabled";
+	};
+
+	uart2: serial@18022000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x18020000 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&axi81_clk>;
+		clock-frequency = <100000000>;
+		status = "disabled";
+	};
+
+	uart3: serial@18023000 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x18023000 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&axi81_clk>;
+		clock-frequency = <100000000>;
+		status = "disabled";
+	};
+
+	gic: interrupt-controller@19021000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x19021000 0x1000>,
+		      <0x19020100 0x100>;
+	};
+
+	L2: l2-cache {
+		compatible = "arm,pl310-cache";
+		reg = <0x19022000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	timer@19020200 {
+		compatible = "arm,cortex-a9-global-timer";
+		reg = <0x19020200 0x100>;
+		interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&periph_clk>;
+	};
+
+};

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

+/dts-v1/;
+/include/ "bcm2835-rpi.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+	model = "Raspberry Pi Model B+";
+
+	leds {
+		act {
+			gpios = <&gpio 47 0>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&gpio 35 0>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
+		};
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+};

arch/arm/boot/dts/bcm2835-rpi-b.dts

 /dts-v1/;
-/include/ "bcm2835.dtsi"
+/include/ "bcm2835-rpi.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
 	model = "Raspberry Pi Model B";
 
-	memory {
-		reg = <0 0x10000000>;
-	};
-
 	leds {
-		compatible = "gpio-leds";
-
 		act {
-			label = "ACT";
 			gpios = <&gpio 16 1>;
-			default-state = "keep";
-			linux,default-trigger = "heartbeat";
 		};
 	};
 };
 
 &gpio {
-	pinctrl-names = "default";
-	pinctrl-0 = <&gpioout &alt0 &alt2 &alt3>;
-
-	gpioout: gpioout {
-		brcm,pins = <6>;
-		brcm,function = <1>; /* GPIO out */
-	};
-
-	alt0: alt0 {
-		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
-		brcm,function = <4>; /* alt0 */
-	};
-
-	alt3: alt3 {
-		brcm,pins = <48 49 50 51 52 53>;
-		brcm,function = <7>; /* alt3 */
-	};
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
 
 	/* I2S interface */
-	alt2: alt2 {
+	i2s_alt2: i2s_alt2 {
 		brcm,pins = <28 29 30 31>;
 		brcm,function = <6>; /* alt2 */
 	};
 };
-
-&i2c0 {
-	status = "okay";
-	clock-frequency = <100000>;
-};
-
-&i2c1 {
-	status = "okay";
-	clock-frequency = <100000>;
-};
-
-&sdhci {
-	status = "okay";
-	bus-width = <4>;
-};

arch/arm/boot/dts/bcm2835-rpi.dtsi

+/include/ "bcm2835.dtsi"
+
+/ {
+	memory {
+		reg = <0 0x10000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		act {
+			label = "ACT";
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&gpio {
+	pinctrl-names = "default";
+
+	gpioout: gpioout {
+		brcm,pins = <6>;
+		brcm,function = <1>; /* GPIO out */
+	};
+
+	alt0: alt0 {
+		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	alt3: alt3 {
+		brcm,pins = <48 49 50 51 52 53>;
+		brcm,function = <7>; /* alt3 */
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+};
+
+&sdhci {
+	status = "okay";
+	bus-width = <4>;
+};

arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts

+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1750DHP
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1750dhp", "brcm,bcm4708";
+	model = "Buffalo WZR-1750DHP (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <200>;
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		sw_ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm4708-netgear-r6250.dts

@@ -32,4 +32,63 @@
 			status = "okay";
 		};
 	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		logo {
+			label = "bcm53xx:white:logo";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		power0 {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		power1 {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		wireless {
+			label = "bcm53xx:blue:wireless";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <200>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+	};
 };

arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts

+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Netgear R6300 V2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	compatible = "netgear,r6300v2", "brcm,bcm4708";
+	model = "Netgear R6300 V2 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		logo {
+			label = "bcm53xx:white:logo";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		power0 {
+			label = "bcm53xx:green:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		power1 {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		wireless {
+			label = "bcm53xx:blue:wireless";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <200>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts

+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-N18U
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+
+/ {
+	compatible = "asus,rt-n18u", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Asus RT-N18U (BCM47081)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan {
+			label = "bcm53xx:blue:wan";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		lan {
+			label = "bcm53xx:blue:lan";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <200>;
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts

+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-600DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm47081.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-600dhp2", "brcm,bcm47081", "brcm,bcm4708";
+	model = "Buffalo WZR-600DHP2 (BCM47081)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <200>;
+
+		aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch device mode? */
+		mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm47081.dtsi

+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for BCM47081 SoC.
+ *
+ * Copyright © 2014 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "bcm5301x.dtsi"
+
+/ {
+	compatible = "brcm,bcm47081";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+	};
+};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -8,6 +8,8 @@
  * Licensed under the GNU/GPL. See COPYING for details.
  */
 
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include "skeleton.dtsi"
@@ -92,4 +94,53 @@
 			clock-frequency = <400000000>;
 		};
 	};
+
+	axi@18000000 {
+		compatible = "brcm,bus-axi";
+		reg = <0x18000000 0x1000>;
+		ranges = <0x00000000 0x18000000 0x00100000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0x000fffff 0xffff>;
+		interrupt-map = 
+			/* ChipCommon */
+			<0x00000000 0 &gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* USB 2.0 Controller */
+			<0x00021000 0 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* USB 3.0 Controller */
+			<0x00023000 0 &gic GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 0 */
+			<0x00024000 0 &gic GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 1 */
+			<0x00025000 0 &gic GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 2 */
+			<0x00026000 0 &gic GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* Ethernet Controller 3 */
+			<0x00027000 0 &gic GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* NAND Controller */
+			<0x00028000 0 &gic GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 1 &gic GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 2 &gic GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 3 &gic GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 4 &gic GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 5 &gic GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 6 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00028000 7 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+
+		chipcommon: chipcommon@0 {
+			reg = <0x00000000 0x1000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+	};
 };

arch/arm/boot/dts/exynos4.dtsi

@@ -392,8 +392,8 @@
 		reg = <0x13400000 0x10000>;
 		interrupts = <0 94 0>;
 		samsung,power-domain = <&pd_mfc>;
-		clocks = <&clock CLK_MFC>;
-		clock-names = "mfc";
+		clocks = <&clock CLK_MFC>, <&clock CLK_SCLK_MFC>;
+		clock-names = "mfc", "sclk_mfc";
 		status = "disabled";
 	};