提交 669bb4c5 编写于 作者: L Linus Torvalds

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32

Pull AVR32 updates from Hans-Christian Noren Egtvedt.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
  avr32: wire up pkey syscalls
  AVR32-pio: Replace two seq_printf() calls by seq_puts() in pio_bank_show()
  AVR32-pio: Use seq_putc() in pio_bank_show()
  AVR32-clock: Combine nine seq_printf() calls into one call in clk_show()
  AVR32-clock: Use seq_putc() in two functions
...@@ -340,5 +340,8 @@ ...@@ -340,5 +340,8 @@
#define __NR_copy_file_range 325 #define __NR_copy_file_range 325
#define __NR_preadv2 326 #define __NR_preadv2 326
#define __NR_pwritev2 327 #define __NR_pwritev2 327
#define __NR_pkey_mprotect 328
#define __NR_pkey_alloc 329
#define __NR_pkey_free 330
#endif /* _UAPI__ASM_AVR32_UNISTD_H */ #endif /* _UAPI__ASM_AVR32_UNISTD_H */
...@@ -341,4 +341,7 @@ sys_call_table: ...@@ -341,4 +341,7 @@ sys_call_table:
.long __sys_copy_file_range .long __sys_copy_file_range
.long __sys_preadv2 .long __sys_preadv2
.long __sys_pwritev2 .long __sys_pwritev2
.long sys_pkey_mprotect
.long sys_pkey_alloc
.long sys_pkey_free /* 330 */
.long sys_ni_syscall /* r8 is saturated at nr_syscalls */ .long sys_ni_syscall /* r8 is saturated at nr_syscalls */
...@@ -242,7 +242,7 @@ dump_clock(struct clk *parent, struct clkinf *r) ...@@ -242,7 +242,7 @@ dump_clock(struct clk *parent, struct clkinf *r)
clk_get_rate(parent)); clk_get_rate(parent));
if (parent->dev) if (parent->dev)
seq_printf(r->s, ", for %s", dev_name(parent->dev)); seq_printf(r->s, ", for %s", dev_name(parent->dev));
seq_printf(r->s, "\n"); seq_putc(r->s, '\n');
/* cost of this scan is small, but not linear... */ /* cost of this scan is small, but not linear... */
r->nest = nest + NEST_DELTA; r->nest = nest + NEST_DELTA;
...@@ -261,23 +261,32 @@ static int clk_show(struct seq_file *s, void *unused) ...@@ -261,23 +261,32 @@ static int clk_show(struct seq_file *s, void *unused)
struct clk *clk; struct clk *clk;
/* show all the power manager registers */ /* show all the power manager registers */
seq_printf(s, "MCCTRL = %8x\n", pm_readl(MCCTRL)); seq_printf(s,
seq_printf(s, "CKSEL = %8x\n", pm_readl(CKSEL)); "MCCTRL = %8x\n"
seq_printf(s, "CPUMASK = %8x\n", pm_readl(CPU_MASK)); "CKSEL = %8x\n"
seq_printf(s, "HSBMASK = %8x\n", pm_readl(HSB_MASK)); "CPUMASK = %8x\n"
seq_printf(s, "PBAMASK = %8x\n", pm_readl(PBA_MASK)); "HSBMASK = %8x\n"
seq_printf(s, "PBBMASK = %8x\n", pm_readl(PBB_MASK)); "PBAMASK = %8x\n"
seq_printf(s, "PLL0 = %8x\n", pm_readl(PLL0)); "PBBMASK = %8x\n"
seq_printf(s, "PLL1 = %8x\n", pm_readl(PLL1)); "PLL0 = %8x\n"
seq_printf(s, "IMR = %8x\n", pm_readl(IMR)); "PLL1 = %8x\n"
"IMR = %8x\n",
pm_readl(MCCTRL),
pm_readl(CKSEL),
pm_readl(CPU_MASK),
pm_readl(HSB_MASK),
pm_readl(PBA_MASK),
pm_readl(PBB_MASK),
pm_readl(PLL0),
pm_readl(PLL1),
pm_readl(IMR));
for (i = 0; i < 8; i++) { for (i = 0; i < 8; i++) {
if (i == 5) if (i == 5)
continue; continue;
seq_printf(s, "GCCTRL%d = %8x\n", i, pm_readl(GCCTRL(i))); seq_printf(s, "GCCTRL%d = %8x\n", i, pm_readl(GCCTRL(i)));
} }
seq_printf(s, "\n"); seq_putc(s, '\n');
r.s = s; r.s = s;
r.nest = 0; r.nest = 0;
/* protected from changes on the list while dumping */ /* protected from changes on the list while dumping */
......
...@@ -367,13 +367,13 @@ static void pio_bank_show(struct seq_file *s, struct gpio_chip *chip) ...@@ -367,13 +367,13 @@ static void pio_bank_show(struct seq_file *s, struct gpio_chip *chip)
(mask & pdsr) ? "hi" : "lo", (mask & pdsr) ? "hi" : "lo",
(mask & pusr) ? " " : "up"); (mask & pusr) ? " " : "up");
if (ifsr & mask) if (ifsr & mask)
seq_printf(s, " deglitch"); seq_puts(s, " deglitch");
if ((osr & mdsr) & mask) if ((osr & mdsr) & mask)
seq_printf(s, " open-drain"); seq_puts(s, " open-drain");
if (imr & mask) if (imr & mask)
seq_printf(s, " irq-%d edge-both", seq_printf(s, " irq-%d edge-both",
gpio_to_irq(chip->base + i)); gpio_to_irq(chip->base + i));
seq_printf(s, "\n"); seq_putc(s, '\n');
} }
} }
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册