net: mvpp2: do not set GMAC autoneg when using XLG MAC

When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/mvpp2.c

@@ -5735,6 +5735,37 @@ static irqreturn_t mvpp2_isr(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static void mvpp2_gmac_set_autoneg(struct mvpp2_port *port,
+				   struct phy_device *phydev)
+{
+	u32 val;
+
+	if (port->phy_interface != PHY_INTERFACE_MODE_RGMII &&
+	    port->phy_interface != PHY_INTERFACE_MODE_RGMII_ID &&
+	    port->phy_interface != PHY_INTERFACE_MODE_RGMII_RXID &&
+	    port->phy_interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+	    port->phy_interface != PHY_INTERFACE_MODE_SGMII)
+		return;
+
+	val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+	val &= ~(MVPP2_GMAC_CONFIG_MII_SPEED |
+		 MVPP2_GMAC_CONFIG_GMII_SPEED |
+		 MVPP2_GMAC_CONFIG_FULL_DUPLEX |
+		 MVPP2_GMAC_AN_SPEED_EN |
+		 MVPP2_GMAC_AN_DUPLEX_EN);
+
+	if (phydev->duplex)
+		val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+
+	if (phydev->speed == SPEED_1000)
+		val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
+	else if (phydev->speed == SPEED_100)
+		val |= MVPP2_GMAC_CONFIG_MII_SPEED;
+
+	writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+
+}
+
 /* Adjust link */
 static void mvpp2_link_event(struct net_device *dev)
 {
@@ -5745,24 +5776,7 @@ static void mvpp2_link_event(struct net_device *dev)
 	if (phydev->link) {
 		if ((port->speed != phydev->speed) ||
 		    (port->duplex != phydev->duplex)) {
-			u32 val;
-
-			val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
-			val &= ~(MVPP2_GMAC_CONFIG_MII_SPEED |
-				 MVPP2_GMAC_CONFIG_GMII_SPEED |
-				 MVPP2_GMAC_CONFIG_FULL_DUPLEX |
-				 MVPP2_GMAC_AN_SPEED_EN |
-				 MVPP2_GMAC_AN_DUPLEX_EN);
-
-			if (phydev->duplex)
-				val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
-
-			if (phydev->speed == SPEED_1000)
-				val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
-			else if (phydev->speed == SPEED_100)
-				val |= MVPP2_GMAC_CONFIG_MII_SPEED;
-
-			writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+			mvpp2_gmac_set_autoneg(port, phydev);
 
 			port->duplex = phydev->duplex;
 			port->speed  = phydev->speed;
@@ -5773,10 +5787,16 @@ static void mvpp2_link_event(struct net_device *dev)
 		port->link = phydev->link;
 
 		if (phydev->link) {
-			val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
-			val |= (MVPP2_GMAC_FORCE_LINK_PASS |
-				MVPP2_GMAC_FORCE_LINK_DOWN);
-			writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+			if (port->phy_interface == PHY_INTERFACE_MODE_RGMII ||
+			    port->phy_interface == PHY_INTERFACE_MODE_RGMII_ID ||
+			    port->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID ||
+			    port->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID ||
+			    port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+				val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+				val |= (MVPP2_GMAC_FORCE_LINK_PASS |
+					MVPP2_GMAC_FORCE_LINK_DOWN);
+				writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+			}
 
 			mvpp2_interrupts_enable(port);
 			mvpp2_port_enable(port);