Merge branch 'linus' into irq/core

Reason: Pull in upstream fixes on which new patches depend on.

Documentation/ABI/testing/sysfs-platform-dell-laptop

-What:		/sys/class/leds/dell::kbd_backlight/als_setting
-Date:		December 2014
-KernelVersion:	3.19
-Contact:	Gabriele Mazzotta <gabriele.mzt@gmail.com>,
-		Pali Rohár <pali.rohar@gmail.com>
-Description:
-		This file allows to control the automatic keyboard
-		illumination mode on some systems that have an ambient
-		light sensor. Write 1 to this file to enable the auto
-		mode, 0 to disable it.
-
-What:		/sys/class/leds/dell::kbd_backlight/start_triggers
-Date:		December 2014
-KernelVersion:	3.19
-Contact:	Gabriele Mazzotta <gabriele.mzt@gmail.com>,
-		Pali Rohár <pali.rohar@gmail.com>
-Description:
-		This file allows to control the input triggers that
-		turn on the keyboard backlight illumination that is
-		disabled because of inactivity.
-		Read the file to see the triggers available. The ones
-		enabled are preceded by '+', those disabled by '-'.
-
-		To enable a trigger, write its name preceded by '+' to
-		this file. To disable a trigger, write its name preceded
-		by '-' instead.
-
-		For example, to enable the keyboard as trigger run:
-		    echo +keyboard > /sys/class/leds/dell::kbd_backlight/start_triggers
-		To disable it:
-		    echo -keyboard > /sys/class/leds/dell::kbd_backlight/start_triggers
-
-		Note that not all the available triggers can be configured.
-
-What:		/sys/class/leds/dell::kbd_backlight/stop_timeout
-Date:		December 2014
-KernelVersion:	3.19
-Contact:	Gabriele Mazzotta <gabriele.mzt@gmail.com>,
-		Pali Rohár <pali.rohar@gmail.com>
-Description:
-		This file allows to specify the interval after which the
-		keyboard illumination is disabled because of inactivity.
-		The timeouts are expressed in seconds, minutes, hours and
-		days, for which the symbols are 's', 'm', 'h' and 'd'
-		respectively.
-
-		To configure the timeout, write to this file a value along
-		with any the above units. If no unit is specified, the value
-		is assumed to be expressed in seconds.
-
-		For example, to set the timeout to 10 minutes run:
-		    echo 10m > /sys/class/leds/dell::kbd_backlight/stop_timeout
-
-		Note that when this file is read, the returned value might be
-		expressed in a different unit than the one used when the timeout
-		was set.
-
-		Also note that only some timeouts are supported and that
-		some systems might fall back to a specific timeout in case
-		an invalid timeout is written to this file.

Documentation/devicetree/bindings/arm/arm-boards

@@ -23,7 +23,7 @@ Required nodes:
     range of 0x200 bytes.
 
 - syscon: the root node of the Integrator platforms must have a
-  system controller node pointong to the control registers,
+  system controller node pointing to the control registers,
   with the compatible string
   "arm,integrator-ap-syscon"
   "arm,integrator-cp-syscon"

Documentation/devicetree/bindings/arm/fw-cfg.txt

+* QEMU Firmware Configuration bindings for ARM
+
+QEMU's arm-softmmu and aarch64-softmmu emulation / virtualization targets
+provide the following Firmware Configuration interface on the "virt" machine
+type:
+
+- A write-only, 16-bit wide selector (or control) register,
+- a read-write, 64-bit wide data register.
+
+QEMU exposes the control and data register to ARM guests as memory mapped
+registers; their location is communicated to the guest's UEFI firmware in the
+DTB that QEMU places at the bottom of the guest's DRAM.
+
+The guest writes a selector value (a key) to the selector register, and then
+can read the corresponding data (produced by QEMU) via the data register. If
+the selected entry is writable, the guest can rewrite it through the data
+register.
+
+The selector register takes keys in big endian byte order.
+
+The data register allows accesses with 8, 16, 32 and 64-bit width (only at
+offset 0 of the register). Accesses larger than a byte are interpreted as
+arrays, bundled together only for better performance. The bytes constituting
+such a word, in increasing address order, correspond to the bytes that would
+have been transferred by byte-wide accesses in chronological order.
+
+The interface allows guest firmware to download various parameters and blobs
+that affect how the firmware works and what tables it installs for the guest
+OS. For example, boot order of devices, ACPI tables, SMBIOS tables, kernel and
+initrd images for direct kernel booting, virtual machine UUID, SMP information,
+virtual NUMA topology, and so on.
+
+The authoritative registry of the valid selector values and their meanings is
+the QEMU source code; the structure of the data blobs corresponding to the
+individual key values is also defined in the QEMU source code.
+
+The presence of the registers can be verified by selecting the "signature" blob
+with key 0x0000, and reading four bytes from the data register. The returned
+signature is "QEMU".
+
+The outermost protocol (involving the write / read sequences of the control and
+data registers) is expected to be versioned, and/or described by feature bits.
+The interface revision / feature bitmap can be retrieved with key 0x0001. The
+blob to be read from the data register has size 4, and it is to be interpreted
+as a uint32_t value in little endian byte order. The current value
+(corresponding to the above outer protocol) is zero.
+
+The guest kernel is not expected to use these registers (although it is
+certainly allowed to); the device tree bindings are documented here because
+this is where device tree bindings reside in general.
+
+Required properties:
+
+- compatible: "qemu,fw-cfg-mmio".
+
+- reg: the MMIO region used by the device.
+  * Bytes 0x0 to 0x7 cover the data register.
+  * Bytes 0x8 to 0x9 cover the selector register.
+  * Further registers may be appended to the region in case of future interface
+    revisions / feature bits.
+
+Example:
+
+/ {
+	#size-cells = <0x2>;
+	#address-cells = <0x2>;
+
+	fw-cfg@9020000 {
+		compatible = "qemu,fw-cfg-mmio";
+		reg = <0x0 0x9020000 0x0 0xa>;
+	};
+};

Documentation/devicetree/bindings/graph.txt

@@ -19,7 +19,7 @@ type of the connections, they just map their existence. Specific properties
 may be described by specialized bindings depending on the type of connection.
 
 To see how this binding applies to video pipelines, for example, see
-Documentation/device-tree/bindings/media/video-interfaces.txt.
+Documentation/devicetree/bindings/media/video-interfaces.txt.
 Here the ports describe data interfaces, and the links between them are
 the connecting data buses. A single port with multiple connections can
 correspond to multiple devices being connected to the same physical bus.

Documentation/devicetree/bindings/net/davinci_emac.txt

@@ -4,7 +4,8 @@ This file provides information, what the device node
 for the davinci_emac interface contains.
 
 Required properties:
-- compatible: "ti,davinci-dm6467-emac" or "ti,am3517-emac"
+- compatible: "ti,davinci-dm6467-emac", "ti,am3517-emac" or
+  "ti,dm816-emac"
 - reg: Offset and length of the register set for the device
 - ti,davinci-ctrl-reg-offset: offset to control register
 - ti,davinci-ctrl-mod-reg-offset: offset to control module register

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -9,7 +9,6 @@ ad	Avionic Design GmbH
 adapteva	Adapteva, Inc.
 adi	Analog Devices, Inc.
 aeroflexgaisler	Aeroflex Gaisler AB
-ak	Asahi Kasei Corp.
 allwinner	Allwinner Technology Co., Ltd.
 altr	Altera Corp.
 amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
@@ -20,6 +19,7 @@ amstaos	AMS-Taos Inc.
 apm	Applied Micro Circuits Corporation (APM)
 arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
+asahi-kasei	Asahi Kasei Corp.
 atmel	Atmel Corporation
 auo	AU Optronics Corporation
 avago	Avago Technologies
@@ -127,6 +127,7 @@ pixcir  PIXCIR MICROELECTRONICS Co., Ltd
 powervr	PowerVR (deprecated, use img)
 qca	Qualcomm Atheros, Inc.
 qcom	Qualcomm Technologies, Inc
+qemu	QEMU, a generic and open source machine emulator and virtualizer
 qnap	QNAP Systems, Inc.
 radxa	Radxa
 raidsonic	RaidSonic Technology GmbH
@@ -168,6 +169,7 @@ usi	Universal Scientific Industrial Co., Ltd.
 v3	V3 Semiconductor
 variscite	Variscite Ltd.
 via	VIA Technologies, Inc.
+virtio	Virtual I/O Device Specification, developed by the OASIS consortium
 voipac	Voipac Technologies s.r.o.
 winbond Winbond Electronics corp.
 wlf	Wolfson Microelectronics

Documentation/kernel-parameters.txt

@@ -1277,6 +1277,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	i8042.notimeout	[HW] Ignore timeout condition signalled by controller
 	i8042.reset	[HW] Reset the controller during init and cleanup
 	i8042.unlock	[HW] Unlock (ignore) the keylock
+	i8042.kbdreset  [HW] Reset device connected to KBD port
 
 	i810=		[HW,DRM]
 

MAINTAINERS

@@ -696,7 +696,7 @@ L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
 W:	http://blackfin.uclinux.org/
 S:	Supported
 F:	sound/soc/blackfin/*
- 
+
 ANALOG DEVICES INC IIO DRIVERS
 M:	Lars-Peter Clausen <lars@metafoo.de>
 M:	Michael Hennerich <Michael.Hennerich@analog.com>
@@ -754,13 +754,6 @@ L:	linux-media@vger.kernel.org
 S:	Maintained
 F:	drivers/media/i2c/aptina-pll.*
 
-ARASAN COMPACT FLASH PATA CONTROLLER
-M:	Viresh Kumar <viresh.linux@gmail.com>
-L:	linux-ide@vger.kernel.org
-S:	Maintained
-F:	include/linux/pata_arasan_cf_data.h
-F:	drivers/ata/pata_arasan_cf.c
-
 ARC FRAMEBUFFER DRIVER
 M:	Jaya Kumar <jayalk@intworks.biz>
 S:	Maintained
@@ -2346,7 +2339,8 @@ CAN NETWORK LAYER
 M:	Oliver Hartkopp <socketcan@hartkopp.net>
 L:	linux-can@vger.kernel.org
 W:	http://gitorious.org/linux-can
-T:	git git://gitorious.org/linux-can/linux-can-next.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git
 S:	Maintained
 F:	Documentation/networking/can.txt
 F:	net/can/
@@ -2361,7 +2355,8 @@ M:	Wolfgang Grandegger <wg@grandegger.com>
 M:	Marc Kleine-Budde <mkl@pengutronix.de>
 L:	linux-can@vger.kernel.org
 W:	http://gitorious.org/linux-can
-T:	git git://gitorious.org/linux-can/linux-can-next.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git
 S:	Maintained
 F:	drivers/net/can/
 F:	include/linux/can/dev.h
@@ -4755,14 +4750,14 @@ S:	Supported
 F:	drivers/net/ethernet/ibm/ibmveth.*
 
 IBM Power Virtual SCSI Device Drivers
-M:	Nathan Fontenot <nfont@linux.vnet.ibm.com>
+M:	Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
 L:	linux-scsi@vger.kernel.org
 S:	Supported
 F:	drivers/scsi/ibmvscsi/ibmvscsi*
 F:	drivers/scsi/ibmvscsi/viosrp.h
 
 IBM Power Virtual FC Device Drivers
-M:	Brian King <brking@linux.vnet.ibm.com>
+M:	Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
 L:	linux-scsi@vger.kernel.org
 S:	Supported
 F:	drivers/scsi/ibmvscsi/ibmvfc*
@@ -4930,7 +4925,6 @@ F:	include/uapi/linux/inotify.h
 
 INPUT (KEYBOARD, MOUSE, JOYSTICK, TOUCHSCREEN) DRIVERS
 M:	Dmitry Torokhov <dmitry.torokhov@gmail.com>
-M:	Dmitry Torokhov <dtor@mail.ru>
 L:	linux-input@vger.kernel.org
 Q:	http://patchwork.kernel.org/project/linux-input/list/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git
@@ -4952,7 +4946,6 @@ K:	\b(ABS|SYN)_MT_
 INTEL C600 SERIES SAS CONTROLLER DRIVER
 M:	Intel SCU Linux support <intel-linux-scu@intel.com>
 M:	Artur Paszkiewicz <artur.paszkiewicz@intel.com>
-M:	Dave Jiang <dave.jiang@intel.com>
 L:	linux-scsi@vger.kernel.org
 T:	git git://git.code.sf.net/p/intel-sas/isci
 S:	Supported
@@ -5703,6 +5696,49 @@ F:	drivers/lguest/
 F:	include/linux/lguest*.h
 F:	tools/lguest/
 
+LIBATA SUBSYSTEM (Serial and Parallel ATA drivers)
+M:	Tejun Heo <tj@kernel.org>
+L:	linux-ide@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
+S:	Maintained
+F:	drivers/ata/
+F:	include/linux/ata.h
+F:	include/linux/libata.h
+
+LIBATA PATA ARASAN COMPACT FLASH CONTROLLER
+M:	Viresh Kumar <viresh.linux@gmail.com>
+L:	linux-ide@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
+S:	Maintained
+F:	include/linux/pata_arasan_cf_data.h
+F:	drivers/ata/pata_arasan_cf.c
+
+LIBATA PATA DRIVERS
+M:	Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
+M:	Tejun Heo <tj@kernel.org>
+L:	linux-ide@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
+S:	Maintained
+F:	drivers/ata/pata_*.c
+F:	drivers/ata/ata_generic.c
+
+LIBATA SATA AHCI PLATFORM devices support
+M:	Hans de Goede <hdegoede@redhat.com>
+M:	Tejun Heo <tj@kernel.org>
+L:	linux-ide@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
+S:	Maintained
+F:	drivers/ata/ahci_platform.c
+F:	drivers/ata/libahci_platform.c
+F:	include/linux/ahci_platform.h
+
+LIBATA SATA PROMISE TX2/TX4 CONTROLLER DRIVER
+M:	Mikael Pettersson <mikpelinux@gmail.com>
+L:	linux-ide@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
+S:	Maintained
+F:	drivers/ata/sata_promise.*
+
 LIBLOCKDEP
 M:	Sasha Levin <sasha.levin@oracle.com>
 S:	Maintained
@@ -6987,14 +7023,12 @@ OPEN FIRMWARE AND FLATTENED DEVICE TREE
 M:	Grant Likely <grant.likely@linaro.org>
 M:	Rob Herring <robh+dt@kernel.org>
 L:	devicetree@vger.kernel.org
-W:	http://fdt.secretlab.ca
-T:	git git://git.secretlab.ca/git/linux-2.6.git
+W:	http://www.devicetree.org/
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux.git
 S:	Maintained
 F:	drivers/of/
 F:	include/linux/of*.h
 F:	scripts/dtc/
-K:	of_get_property
-K:	of_match_table
 
 OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
 M:	Rob Herring <robh+dt@kernel.org>
@@ -7239,7 +7273,7 @@ S:	Maintained
 F:	drivers/pci/host/*layerscape*
 
 PCI DRIVER FOR IMX6
-M:	Richard Zhu <r65037@freescale.com>
+M:	Richard Zhu <Richard.Zhu@freescale.com>
 M:	Lucas Stach <l.stach@pengutronix.de>
 L:	linux-pci@vger.kernel.org
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -7409,6 +7443,7 @@ F:	drivers/crypto/picoxcell*
 PIN CONTROL SUBSYSTEM
 M:	Linus Walleij <linus.walleij@linaro.org>
 L:	linux-gpio@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git
 S:	Maintained
 F:	drivers/pinctrl/
 F:	include/linux/pinctrl/
@@ -7576,12 +7611,6 @@ W:	http://wireless.kernel.org/en/users/Drivers/p54
 S:	Obsolete
 F:	drivers/net/wireless/prism54/
 
-PROMISE SATA TX2/TX4 CONTROLLER LIBATA DRIVER
-M:	Mikael Pettersson <mikpelinux@gmail.com>
-L:	linux-ide@vger.kernel.org
-S:	Maintained
-F:	drivers/ata/sata_promise.*
-
 PS3 NETWORK SUPPORT
 M:	Geoff Levand <geoff@infradead.org>
 L:	netdev@vger.kernel.org
@@ -8555,25 +8584,6 @@ S:	Maintained
 F:	drivers/misc/phantom.c
 F:	include/uapi/linux/phantom.h
 
-SERIAL ATA (SATA) SUBSYSTEM
-M:	Tejun Heo <tj@kernel.org>
-L:	linux-ide@vger.kernel.org
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
-S:	Supported
-F:	drivers/ata/
-F:	include/linux/ata.h
-F:	include/linux/libata.h
-
-SERIAL ATA AHCI PLATFORM devices support
-M:	Hans de Goede <hdegoede@redhat.com>
-M:	Tejun Heo <tj@kernel.org>
-L:	linux-ide@vger.kernel.org
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata.git
-S:	Supported
-F:	drivers/ata/ahci_platform.c
-F:	drivers/ata/libahci_platform.c
-F:	include/linux/ahci_platform.h
-
 SERVER ENGINES 10Gbps iSCSI - BladeEngine 2 DRIVER
 M:	Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
 L:	linux-scsi@vger.kernel.org

Makefile

 VERSION = 3
 PATCHLEVEL = 19
 SUBLEVEL = 0
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
 NAME = Diseased Newt
 
 # *DOCUMENTATION*

arch/alpha/kernel/pci.c

@@ -285,8 +285,12 @@ pcibios_claim_one_bus(struct pci_bus *b)
 			if (r->parent || !r->start || !r->flags)
 				continue;
 			if (pci_has_flag(PCI_PROBE_ONLY) ||
-			    (r->flags & IORESOURCE_PCI_FIXED))
-				pci_claim_resource(dev, i);
+			    (r->flags & IORESOURCE_PCI_FIXED)) {
+				if (pci_claim_resource(dev, i) == 0)
+					continue;
+
+				pci_claim_bridge_resource(dev, i);
+			}
 		}
 	}
 

arch/arm/boot/dts/dra7.dtsi

@@ -1257,6 +1257,8 @@
 				tx-fifo-resize;
 				maximum-speed = "super-speed";
 				dr_mode = "otg";
+				snps,dis_u3_susphy_quirk;
+				snps,dis_u2_susphy_quirk;
 			};
 		};
 
@@ -1278,6 +1280,8 @@
 				tx-fifo-resize;
 				maximum-speed = "high-speed";
 				dr_mode = "otg";
+				snps,dis_u3_susphy_quirk;
+				snps,dis_u2_susphy_quirk;
 			};
 		};
 
@@ -1299,6 +1303,8 @@
 				tx-fifo-resize;
 				maximum-speed = "high-speed";
 				dr_mode = "otg";
+				snps,dis_u3_susphy_quirk;
+				snps,dis_u2_susphy_quirk;
 			};
 		};
 

arch/arm/boot/dts/imx25.dtsi

@@ -369,7 +369,7 @@
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
 				#pwm-cells = <2>;
 				reg = <0x53fa0000 0x4000>;
-				clocks = <&clks 106>, <&clks 36>;
+				clocks = <&clks 106>, <&clks 52>;
 				clock-names = "ipg", "per";
 				interrupts = <36>;
 			};
@@ -388,7 +388,7 @@
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
 				#pwm-cells = <2>;
 				reg = <0x53fa8000 0x4000>;
-				clocks = <&clks 107>, <&clks 36>;
+				clocks = <&clks 107>, <&clks 52>;
 				clock-names = "ipg", "per";
 				interrupts = <41>;
 			};
@@ -429,7 +429,7 @@
 			pwm4: pwm@53fc8000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
 				reg = <0x53fc8000 0x4000>;
-				clocks = <&clks 108>, <&clks 36>;
+				clocks = <&clks 108>, <&clks 52>;
 				clock-names = "ipg", "per";
 				interrupts = <42>;
 			};
@@ -476,7 +476,7 @@
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
 				#pwm-cells = <2>;
 				reg = <0x53fe0000 0x4000>;
-				clocks = <&clks 105>, <&clks 36>;
+				clocks = <&clks 105>, <&clks 52>;
 				clock-names = "ipg", "per";
 				interrupts = <26>;
 			};

arch/arm/boot/dts/tegra20-seaboard.dts

@@ -406,7 +406,7 @@
 		clock-frequency = <400000>;
 
 		magnetometer@c {
-			compatible = "ak,ak8975";
+			compatible = "asahi-kasei,ak8975";
 			reg = <0xc>;
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(N, 5) IRQ_TYPE_LEVEL_HIGH>;

arch/arm/kernel/entry-header.S

@@ -253,21 +253,22 @@
 	.endm
 
 	.macro	restore_user_regs, fast = 0, offset = 0
-	ldr	r1, [sp, #\offset + S_PSR]	@ get calling cpsr
-	ldr	lr, [sp, #\offset + S_PC]!	@ get pc
+	mov	r2, sp
+	ldr	r1, [r2, #\offset + S_PSR]	@ get calling cpsr
+	ldr	lr, [r2, #\offset + S_PC]!	@ get pc
 	msr	spsr_cxsf, r1			@ save in spsr_svc
 #if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_32v6K)
 	@ We must avoid clrex due to Cortex-A15 erratum #830321
-	strex	r1, r2, [sp]			@ clear the exclusive monitor
+	strex	r1, r2, [r2]			@ clear the exclusive monitor
 #endif
 	.if	\fast
-	ldmdb	sp, {r1 - lr}^			@ get calling r1 - lr
+	ldmdb	r2, {r1 - lr}^			@ get calling r1 - lr
 	.else
-	ldmdb	sp, {r0 - lr}^			@ get calling r0 - lr
+	ldmdb	r2, {r0 - lr}^			@ get calling r0 - lr
 	.endif
 	mov	r0, r0				@ ARMv5T and earlier require a nop
 						@ after ldm {}^
-	add	sp, sp, #S_FRAME_SIZE - S_PC
+	add	sp, sp, #\offset + S_FRAME_SIZE
 	movs	pc, lr				@ return & move spsr_svc into cpsr
 	.endm
 

arch/arm/kernel/perf_event.c

@@ -116,8 +116,14 @@ int armpmu_event_set_period(struct perf_event *event)
 		ret = 1;
 	}
 
-	if (left > (s64)armpmu->max_period)
-		left = armpmu->max_period;
+	/*
+	 * Limit the maximum period to prevent the counter value
+	 * from overtaking the one we are about to program. In
+	 * effect we are reducing max_period to account for
+	 * interrupt latency (and we are being very conservative).
+	 */
+	if (left > (armpmu->max_period >> 1))
+		left = armpmu->max_period >> 1;
 
 	local64_set(&hwc->prev_count, (u64)-left);
 

arch/arm/kernel/setup.c

@@ -657,10 +657,13 @@ int __init arm_add_memory(u64 start, u64 size)
 
 	/*
 	 * Ensure that start/size are aligned to a page boundary.
-	 * Size is appropriately rounded down, start is rounded up.
+	 * Size is rounded down, start is rounded up.
 	 */
-	size -= start & ~PAGE_MASK;
 	aligned_start = PAGE_ALIGN(start);
+	if (aligned_start > start + size)
+		size = 0;
+	else
+		size -= aligned_start - start;
 
 #ifndef CONFIG_ARCH_PHYS_ADDR_T_64BIT
 	if (aligned_start > ULONG_MAX) {

arch/arm/mach-mvebu/coherency.c

@@ -246,9 +246,14 @@ static int coherency_type(void)
 	return type;
 }
 
+/*
+ * As a precaution, we currently completely disable hardware I/O
+ * coherency, until enough testing is done with automatic I/O
+ * synchronization barriers to validate that it is a proper solution.
+ */
 int coherency_available(void)
 {
-	return coherency_type() != COHERENCY_FABRIC_TYPE_NONE;
+	return false;
 }
 
 int __init coherency_init(void)

arch/arm/mach-omap2/common.h

@@ -211,6 +211,7 @@ extern struct device *omap2_get_iva_device(void);
 extern struct device *omap2_get_l3_device(void);
 extern struct device *omap4_get_dsp_device(void);
 
+unsigned int omap4_xlate_irq(unsigned int hwirq);
 void omap_gic_of_init(void);
 
 #ifdef CONFIG_CACHE_L2X0

arch/arm/mach-omap2/omap4-common.c

@@ -256,6 +256,38 @@ static int __init omap4_sar_ram_init(void)
 }
 omap_early_initcall(omap4_sar_ram_init);
 
+static struct of_device_id gic_match[] = {
+	{ .compatible = "arm,cortex-a9-gic", },
+	{ .compatible = "arm,cortex-a15-gic", },
+	{ },
+};
+
+static struct device_node *gic_node;
+
+unsigned int omap4_xlate_irq(unsigned int hwirq)
+{
+	struct of_phandle_args irq_data;
+	unsigned int irq;
+
+	if (!gic_node)
+		gic_node = of_find_matching_node(NULL, gic_match);
+
+	if (WARN_ON(!gic_node))
+		return hwirq;
+
+	irq_data.np = gic_node;
+	irq_data.args_count = 3;
+	irq_data.args[0] = 0;
+	irq_data.args[1] = hwirq - OMAP44XX_IRQ_GIC_START;
+	irq_data.args[2] = IRQ_TYPE_LEVEL_HIGH;
+
+	irq = irq_create_of_mapping(&irq_data);
+	if (WARN_ON(!irq))
+		irq = hwirq;
+
+	return irq;
+}
+
 void __init omap_gic_of_init(void)
 {
 	struct device_node *np;

arch/arm/mach-omap2/omap_hwmod.c

@@ -3534,9 +3534,15 @@ int omap_hwmod_fill_resources(struct omap_hwmod *oh, struct resource *res)
 
 	mpu_irqs_cnt = _count_mpu_irqs(oh);
 	for (i = 0; i < mpu_irqs_cnt; i++) {
+		unsigned int irq;
+
+		if (oh->xlate_irq)
+			irq = oh->xlate_irq((oh->mpu_irqs + i)->irq);
+		else
+			irq = (oh->mpu_irqs + i)->irq;
 		(res + r)->name = (oh->mpu_irqs + i)->name;
-		(res + r)->start = (oh->mpu_irqs + i)->irq;
-		(res + r)->end = (oh->mpu_irqs + i)->irq;
+		(res + r)->start = irq;
+		(res + r)->end = irq;
 		(res + r)->flags = IORESOURCE_IRQ;
 		r++;
 	}

arch/arm/mach-omap2/omap_hwmod.h

@@ -676,6 +676,7 @@ struct omap_hwmod {
 	spinlock_t			_lock;
 	struct list_head		node;
 	struct omap_hwmod_ocp_if	*_mpu_port;
+	unsigned int			(*xlate_irq)(unsigned int);
 	u16				flags;
 	u8				mpu_rt_idx;
 	u8				response_lat;

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -479,6 +479,7 @@ static struct omap_hwmod omap44xx_dma_system_hwmod = {
 	.class		= &omap44xx_dma_hwmod_class,
 	.clkdm_name	= "l3_dma_clkdm",
 	.mpu_irqs	= omap44xx_dma_system_irqs,
+	.xlate_irq	= omap4_xlate_irq,
 	.main_clk	= "l3_div_ck",
 	.prcm = {
 		.omap4 = {
@@ -640,6 +641,7 @@ static struct omap_hwmod omap44xx_dss_dispc_hwmod = {
 	.class		= &omap44xx_dispc_hwmod_class,
 	.clkdm_name	= "l3_dss_clkdm",
 	.mpu_irqs	= omap44xx_dss_dispc_irqs,
+	.xlate_irq	= omap4_xlate_irq,
 	.sdma_reqs	= omap44xx_dss_dispc_sdma_reqs,
 	.main_clk	= "dss_dss_clk",
 	.prcm = {
@@ -693,6 +695,7 @@ static struct omap_hwmod omap44xx_dss_dsi1_hwmod = {
 	.class		= &omap44xx_dsi_hwmod_class,
 	.clkdm_name	= "l3_dss_clkdm",
 	.mpu_irqs	= omap44xx_dss_dsi1_irqs,
+	.xlate_irq	= omap4_xlate_irq,
 	.sdma_reqs	= omap44xx_dss_dsi1_sdma_reqs,
 	.main_clk	= "dss_dss_clk",
 	.prcm = {
@@ -726,6 +729,7 @@ static struct omap_hwmod omap44xx_dss_dsi2_hwmod = {
 	.class		= &omap44xx_dsi_hwmod_class,
 	.clkdm_name	= "l3_dss_clkdm",
 	.mpu_irqs	= omap44xx_dss_dsi2_irqs,
+	.xlate_irq	= omap4_xlate_irq,
 	.sdma_reqs	= omap44xx_dss_dsi2_sdma_reqs,
 	.main_clk	= "dss_dss_clk",
 	.prcm = {
@@ -784,6 +788,7 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = {
 	 */
 	.flags		= HWMOD_SWSUP_SIDLE,
 	.mpu_irqs	= omap44xx_dss_hdmi_irqs,
+	.xlate_irq	= omap4_xlate_irq,
 	.sdma_reqs	= omap44xx_dss_hdmi_sdma_reqs,
 	.main_clk	= "dss_48mhz_clk",
 	.prcm = {

arch/arm/mach-omap2/omap_hwmod_54xx_data.c

@@ -288,6 +288,7 @@ static struct omap_hwmod omap54xx_dma_system_hwmod = {
 	.class		= &omap54xx_dma_hwmod_class,
 	.clkdm_name	= "dma_clkdm",
 	.mpu_irqs	= omap54xx_dma_system_irqs,
+	.xlate_irq	= omap4_xlate_irq,
 	.main_clk	= "l3_iclk_div",
 	.prcm = {
 		.omap4 = {

arch/arm/mach-omap2/prcm-common.h

@@ -498,6 +498,7 @@ struct omap_prcm_irq_setup {
 	u8 nr_irqs;
 	const struct omap_prcm_irq *irqs;
 	int irq;
+	unsigned int (*xlate_irq)(unsigned int);
 	void (*read_pending_irqs)(unsigned long *events);
 	void (*ocp_barrier)(void);
 	void (*save_and_clear_irqen)(u32 *saved_mask);

arch/arm/mach-omap2/prm44xx.c

@@ -49,6 +49,7 @@ static struct omap_prcm_irq_setup omap4_prcm_irq_setup = {
 	.irqs			= omap4_prcm_irqs,
 	.nr_irqs		= ARRAY_SIZE(omap4_prcm_irqs),
 	.irq			= 11 + OMAP44XX_IRQ_GIC_START,
+	.xlate_irq		= omap4_xlate_irq,
 	.read_pending_irqs	= &omap44xx_prm_read_pending_irqs,
 	.ocp_barrier		= &omap44xx_prm_ocp_barrier,
 	.save_and_clear_irqen	= &omap44xx_prm_save_and_clear_irqen,
@@ -751,8 +752,10 @@ static int omap44xx_prm_late_init(void)
 		}
 
 		/* Once OMAP4 DT is filled as well */
-		if (irq_num >= 0)
+		if (irq_num >= 0) {
 			omap4_prcm_irq_setup.irq = irq_num;
+			omap4_prcm_irq_setup.xlate_irq = NULL;
+		}
 	}
 
 	omap44xx_prm_enable_io_wakeup();

arch/arm/mach-omap2/prm_common.c

@@ -187,6 +187,7 @@ int omap_prcm_event_to_irq(const char *name)
  */
 void omap_prcm_irq_cleanup(void)
 {
+	unsigned int irq;
 	int i;
 
 	if (!prcm_irq_setup) {
@@ -211,7 +212,11 @@ void omap_prcm_irq_cleanup(void)
 	kfree(prcm_irq_setup->priority_mask);
 	prcm_irq_setup->priority_mask = NULL;
 
-	irq_set_chained_handler(prcm_irq_setup->irq, NULL);
+	if (prcm_irq_setup->xlate_irq)
+		irq = prcm_irq_setup->xlate_irq(prcm_irq_setup->irq);
+	else
+		irq = prcm_irq_setup->irq;
+	irq_set_chained_handler(irq, NULL);
 
 	if (prcm_irq_setup->base_irq > 0)
 		irq_free_descs(prcm_irq_setup->base_irq,
@@ -259,6 +264,7 @@ int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup)
 	int offset, i;
 	struct irq_chip_generic *gc;
 	struct irq_chip_type *ct;
+	unsigned int irq;
 
 	if (!irq_setup)
 		return -EINVAL;
@@ -298,7 +304,11 @@ int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup)
 				1 << (offset & 0x1f);
 	}
 
-	irq_set_chained_handler(irq_setup->irq, omap_prcm_irq_handler);
+	if (irq_setup->xlate_irq)
+		irq = irq_setup->xlate_irq(irq_setup->irq);
+	else
+		irq = irq_setup->irq;
+	irq_set_chained_handler(irq, omap_prcm_irq_handler);
 
 	irq_setup->base_irq = irq_alloc_descs(-1, 0, irq_setup->nr_regs * 32,
 		0);

arch/arm/mach-omap2/twl-common.c

@@ -66,19 +66,24 @@ void __init omap_pmic_init(int bus, u32 clkrate,
 	omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
 }
 
+#ifdef CONFIG_ARCH_OMAP4
 void __init omap4_pmic_init(const char *pmic_type,
 		    struct twl4030_platform_data *pmic_data,
 		    struct i2c_board_info *devices, int nr_devices)
 {
 	/* PMIC part*/
+	unsigned int irq;
+
 	omap_mux_init_signal("sys_nirq1", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
 	omap_mux_init_signal("fref_clk0_out.sys_drm_msecure", OMAP_PIN_OUTPUT);
-	omap_pmic_init(1, 400, pmic_type, 7 + OMAP44XX_IRQ_GIC_START, pmic_data);
+	irq = omap4_xlate_irq(7 + OMAP44XX_IRQ_GIC_START);
+	omap_pmic_init(1, 400, pmic_type, irq, pmic_data);
 
 	/* Register additional devices on i2c1 bus if needed */
 	if (devices)
 		i2c_register_board_info(1, devices, nr_devices);
 }
+#endif
 
 void __init omap_pmic_late_init(void)
 {

arch/arm/mach-shmobile/setup-r8a7778.c

@@ -576,11 +576,18 @@ void __init r8a7778_init_irq_extpin(int irlm)
 void __init r8a7778_init_irq_dt(void)
 {
 	void __iomem *base = ioremap_nocache(0xfe700000, 0x00100000);
+#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
+	void __iomem *gic_dist_base = ioremap_nocache(0xfe438000, 0x1000);
+	void __iomem *gic_cpu_base = ioremap_nocache(0xfe430000, 0x1000);
+#endif
 
 	BUG_ON(!base);
 
+#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
+	gic_init(0, 29, gic_dist_base, gic_cpu_base);
+#else
 	irqchip_init();
-
+#endif
 	/* route all interrupts to ARM */
 	__raw_writel(0x73ffffff, base + INT2NTSR0);
 	__raw_writel(0xffffffff, base + INT2NTSR1);

arch/arm/mach-shmobile/setup-r8a7779.c

@@ -720,10 +720,17 @@ static int r8a7779_set_wake(struct irq_data *data, unsigned int on)
 
 void __init r8a7779_init_irq_dt(void)
 {
+#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
+	void __iomem *gic_dist_base = ioremap_nocache(0xf0001000, 0x1000);
+	void __iomem *gic_cpu_base = ioremap_nocache(0xf0000100, 0x1000);
+#endif
 	gic_arch_extn.irq_set_wake = r8a7779_set_wake;
 
+#ifdef CONFIG_ARCH_SHMOBILE_LEGACY
+	gic_init(0, 29, gic_dist_base, gic_cpu_base);
+#else
 	irqchip_init();
-
+#endif
 	/* route all interrupts to ARM */
 	__raw_writel(0xffffffff, INT2NTSR0);
 	__raw_writel(0x3fffffff, INT2NTSR1);

arch/arm64/Makefile

@@ -85,6 +85,7 @@ vdso_install:
 # We use MRPROPER_FILES and CLEAN_FILES now
 archclean:
 	$(Q)$(MAKE) $(clean)=$(boot)
+	$(Q)$(MAKE) $(clean)=$(boot)/dts
 
 define archhelp
   echo  '* Image.gz      - Compressed kernel image (arch/$(ARCH)/boot/Image.gz)'

arch/arm64/boot/dts/Makefile

@@ -3,6 +3,4 @@ dts-dirs += apm
 dts-dirs += arm
 dts-dirs += cavium
 
-always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)
-clean-files	:= *.dtb

arch/arm64/boot/dts/arm/juno.dts

@@ -22,7 +22,7 @@
 	};
 
 	chosen {
-		stdout-path = &soc_uart0;
+		stdout-path = "serial0:115200n8";
 	};
 
 	psci {

arch/arm64/mm/dump.c

@@ -15,6 +15,7 @@
  */
 #include <linux/debugfs.h>
 #include <linux/fs.h>
+#include <linux/io.h>
 #include <linux/mm.h>
 #include <linux/sched.h>
 #include <linux/seq_file.h>

arch/avr32/kernel/module.c

@@ -19,12 +19,10 @@
 #include <linux/moduleloader.h>
 #include <linux/vmalloc.h>
 
-void module_free(struct module *mod, void *module_region)
+void module_arch_freeing_init(struct module *mod)
 {
 	vfree(mod->arch.syminfo);
 	mod->arch.syminfo = NULL;
-
-	vfree(module_region);
 }
 
 static inline int check_rela(Elf32_Rela *rela, struct module *module,
@@ -291,12 +289,3 @@ int apply_relocate_add(Elf32_Shdr *sechdrs, const char *strtab,
 
 	return ret;
 }
-
-int module_finalize(const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs,
-		    struct module *module)
-{
-	vfree(module->arch.syminfo);
-	module->arch.syminfo = NULL;
-
-	return 0;
-}

arch/cris/arch-v32/drivers/sync_serial.c

@@ -604,7 +604,7 @@ static ssize_t __sync_serial_read(struct file *file,
 				  struct timespec *ts)
 {
 	unsigned long flags;
-	int dev = MINOR(file->f_dentry->d_inode->i_rdev);
+	int dev = MINOR(file_inode(file)->i_rdev);
 	int avail;
 	struct sync_port *port;
 	unsigned char *start;

arch/cris/kernel/module.c

@@ -36,7 +36,7 @@ void *module_alloc(unsigned long size)
 }
 
 /* Free memory returned from module_alloc */
-void module_free(struct module *mod, void *module_region)
+void module_memfree(void *module_region)
 {
 	kfree(module_region);
 }

arch/frv/mb93090-mb00/pci-frv.c

@@ -94,7 +94,7 @@ static void __init pcibios_allocate_bus_resources(struct list_head *bus_list)
 				r = &dev->resource[idx];
 				if (!r->start)
 					continue;
-				pci_claim_resource(dev, idx);
+				pci_claim_bridge_resource(dev, idx);
 			}
 		}
 		pcibios_allocate_bus_resources(&bus->children);

arch/ia64/kernel/module.c

@@ -305,14 +305,12 @@ plt_target (struct plt_entry *plt)
 #endif /* !USE_BRL */
 
 void
-module_free (struct module *mod, void *module_region)
+module_arch_freeing_init (struct module *mod)
 {
-	if (mod && mod->arch.init_unw_table &&
-	    module_region == mod->module_init) {
+	if (mod->arch.init_unw_table) {
 		unw_remove_unwind_table(mod->arch.init_unw_table);
 		mod->arch.init_unw_table = NULL;
 	}
-	vfree(module_region);
 }
 
 /* Have we already seen one of these relocations? */

arch/ia64/pci/pci.c

@@ -487,45 +487,39 @@ int pcibios_root_bridge_prepare(struct pci_host_bridge *bridge)
 	return 0;
 }
 
-static int is_valid_resource(struct pci_dev *dev, int idx)
+void pcibios_fixup_device_resources(struct pci_dev *dev)
 {
-	unsigned int i, type_mask = IORESOURCE_IO | IORESOURCE_MEM;
-	struct resource *devr = &dev->resource[idx], *busr;
+	int idx;
 
 	if (!dev->bus)
-		return 0;
-
-	pci_bus_for_each_resource(dev->bus, busr, i) {
-		if (!busr || ((busr->flags ^ devr->flags) & type_mask))
-			continue;
-		if ((devr->start) && (devr->start >= busr->start) &&
-				(devr->end <= busr->end))
-			return 1;
-	}
-	return 0;
-}
+		return;
 
-static void pcibios_fixup_resources(struct pci_dev *dev, int start, int limit)
-{
-	int i;
+	for (idx = 0; idx < PCI_BRIDGE_RESOURCES; idx++) {
+		struct resource *r = &dev->resource[idx];
 
-	for (i = start; i < limit; i++) {
-		if (!dev->resource[i].flags)
+		if (!r->flags || r->parent || !r->start)
 			continue;
-		if ((is_valid_resource(dev, i)))
-			pci_claim_resource(dev, i);
-	}
-}
 
-void pcibios_fixup_device_resources(struct pci_dev *dev)
-{
-	pcibios_fixup_resources(dev, 0, PCI_BRIDGE_RESOURCES);
+		pci_claim_resource(dev, idx);
+	}
 }
 EXPORT_SYMBOL_GPL(pcibios_fixup_device_resources);
 
 static void pcibios_fixup_bridge_resources(struct pci_dev *dev)
 {
-	pcibios_fixup_resources(dev, PCI_BRIDGE_RESOURCES, PCI_NUM_RESOURCES);
+	int idx;
+
+	if (!dev->bus)
+		return;
+
+	for (idx = PCI_BRIDGE_RESOURCES; idx < PCI_NUM_RESOURCES; idx++) {
+		struct resource *r = &dev->resource[idx];
+
+		if (!r->flags || r->parent || !r->start)
+			continue;
+
+		pci_claim_bridge_resource(dev, idx);
+	}
 }
 
 /*

arch/microblaze/pci/pci-common.c

@@ -1026,6 +1026,8 @@ static void pcibios_allocate_bus_resources(struct pci_bus *bus)
 			 pr, (pr && pr->name) ? pr->name : "nil");
 
 		if (pr && !(pr->flags & IORESOURCE_UNSET)) {
+			struct pci_dev *dev = bus->self;
+
 			if (request_resource(pr, res) == 0)
 				continue;
 			/*
@@ -1035,6 +1037,12 @@ static void pcibios_allocate_bus_resources(struct pci_bus *bus)
 			 */
 			if (reparent_resources(pr, res) == 0)
 				continue;
+
+			if (dev && i < PCI_BRIDGE_RESOURCE_NUM &&
+			    pci_claim_bridge_resource(dev,
+						 i + PCI_BRIDGE_RESOURCES) == 0)
+				continue;
+
 		}
 		pr_warn("PCI: Cannot allocate resource region ");
 		pr_cont("%d of PCI bridge %d, will remap\n", i, bus->number);
@@ -1227,7 +1235,10 @@ void pcibios_claim_one_bus(struct pci_bus *bus)
 				 (unsigned long long)r->end,
 				 (unsigned int)r->flags);
 
-			pci_claim_resource(dev, i);
+			if (pci_claim_resource(dev, i) == 0)
+				continue;
+
+			pci_claim_bridge_resource(dev, i);
 		}
 	}
 

arch/mips/net/bpf_jit.c

@@ -1388,7 +1388,7 @@ void bpf_jit_compile(struct bpf_prog *fp)
 void bpf_jit_free(struct bpf_prog *fp)
 {
 	if (fp->jited)
-		module_free(NULL, fp->bpf_func);
+		module_memfree(fp->bpf_func);
 
 	bpf_prog_unlock_free(fp);
 }

arch/mn10300/unit-asb2305/pci-asb2305.c

@@ -106,7 +106,7 @@ static void __init pcibios_allocate_bus_resources(struct list_head *bus_list)
 				if (!r->flags)
 					continue;
 				if (!r->start ||
-				    pci_claim_resource(dev, idx) < 0) {
+				    pci_claim_bridge_resource(dev, idx) < 0) {
 					printk(KERN_ERR "PCI:"
 					       " Cannot allocate resource"
 					       " region %d of bridge %s\n",

arch/mn10300/unit-asb2305/pci.c

@@ -281,42 +281,37 @@ static int __init pci_check_direct(void)
 	return -ENODEV;
 }
 
-static int is_valid_resource(struct pci_dev *dev, int idx)
+static void pcibios_fixup_device_resources(struct pci_dev *dev)
 {
-	unsigned int i, type_mask = IORESOURCE_IO | IORESOURCE_MEM;
-	struct resource *devr = &dev->resource[idx], *busr;
-
-	if (dev->bus) {
-		pci_bus_for_each_resource(dev->bus, busr, i) {
-			if (!busr || (busr->flags ^ devr->flags) & type_mask)
-				continue;
-
-			if (devr->start &&
-			    devr->start >= busr->start &&
-			    devr->end <= busr->end)
-				return 1;
-		}
-	}
+	int idx;
 
-	return 0;
+	if (!dev->bus)
+		return;
+
+	for (idx = 0; idx < PCI_BRIDGE_RESOURCES; idx++) {
+		struct resource *r = &dev->resource[idx];
+
+		if (!r->flags || r->parent || !r->start)
+			continue;
+
+		pci_claim_resource(dev, idx);
+	}
 }
 
-static void pcibios_fixup_device_resources(struct pci_dev *dev)
+static void pcibios_fixup_bridge_resources(struct pci_dev *dev)
 {
-	int limit, i;
+	int idx;
 
-	if (dev->bus->number != 0)
+	if (!dev->bus)
 		return;
 
-	limit = (dev->hdr_type == PCI_HEADER_TYPE_NORMAL) ?
-		PCI_BRIDGE_RESOURCES : PCI_NUM_RESOURCES;
+	for (idx = PCI_BRIDGE_RESOURCES; idx < PCI_NUM_RESOURCES; idx++) {
+		struct resource *r = &dev->resource[idx];
 
-	for (i = 0; i < limit; i++) {
-		if (!dev->resource[i].flags)
+		if (!r->flags || r->parent || !r->start)
 			continue;
 
-		if (is_valid_resource(dev, i))
-			pci_claim_resource(dev, i);
+		pci_claim_bridge_resource(dev, idx);
 	}
 }
 
@@ -330,7 +325,7 @@ void pcibios_fixup_bus(struct pci_bus *bus)
 
 	if (bus->self) {
 		pci_read_bridge_bases(bus);
-		pcibios_fixup_device_resources(bus->self);
+		pcibios_fixup_bridge_resources(bus->self);
 	}
 
 	list_for_each_entry(dev, &bus->devices, bus_list)

arch/nios2/kernel/module.c

@@ -36,7 +36,7 @@ void *module_alloc(unsigned long size)
 }
 
 /* Free memory returned from module_alloc */
-void module_free(struct module *mod, void *module_region)
+void module_memfree(void *module_region)
 {
 	kfree(module_region);
 }

arch/nios2/kernel/signal.c

@@ -200,7 +200,7 @@ static int setup_rt_frame(struct ksignal *ksig, sigset_t *set,
 
 	/* Set up to return from userspace; jump to fixed address sigreturn
 	   trampoline on kuser page.  */
-	regs->ra = (unsigned long) (0x1040);
+	regs->ra = (unsigned long) (0x1044);
 
 	/* Set up registers for signal handler */
 	regs->sp = (unsigned long) frame;

arch/parisc/kernel/module.c

@@ -298,14 +298,10 @@ static inline unsigned long count_stubs(const Elf_Rela *rela, unsigned long n)
 }
 #endif
 
-
-/* Free memory returned from module_alloc */
-void module_free(struct module *mod, void *module_region)
+void module_arch_freeing_init(struct module *mod)
 {
 	kfree(mod->arch.section);
 	mod->arch.section = NULL;
-
-	vfree(module_region);
 }
 
 /* Additional bytes needed in front of individual sections */

arch/powerpc/crypto/sha1.c

@@ -154,4 +154,5 @@ module_exit(sha1_powerpc_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("SHA1 Secure Hash Algorithm");
 
+MODULE_ALIAS_CRYPTO("sha1");
 MODULE_ALIAS_CRYPTO("sha1-powerpc");

arch/powerpc/kernel/pci-common.c

@@ -1184,6 +1184,8 @@ static void pcibios_allocate_bus_resources(struct pci_bus *bus)
 			 pr, (pr && pr->name) ? pr->name : "nil");
 
 		if (pr && !(pr->flags & IORESOURCE_UNSET)) {
+			struct pci_dev *dev = bus->self;
+
 			if (request_resource(pr, res) == 0)
 				continue;
 			/*
@@ -1193,6 +1195,11 @@ static void pcibios_allocate_bus_resources(struct pci_bus *bus)
 			 */
 			if (reparent_resources(pr, res) == 0)
 				continue;
+
+			if (dev && i < PCI_BRIDGE_RESOURCE_NUM &&
+			    pci_claim_bridge_resource(dev,
+						i + PCI_BRIDGE_RESOURCES) == 0)
+				continue;
 		}
 		pr_warning("PCI: Cannot allocate resource region "
 			   "%d of PCI bridge %d, will remap\n", i, bus->number);
@@ -1401,7 +1408,10 @@ void pcibios_claim_one_bus(struct pci_bus *bus)
 				 (unsigned long long)r->end,
 				 (unsigned int)r->flags);
 
-			pci_claim_resource(dev, i);
+			if (pci_claim_resource(dev, i) == 0)
+				continue;
+
+			pci_claim_bridge_resource(dev, i);
 		}
 	}
 

arch/powerpc/net/bpf_jit_comp.c

@@ -699,7 +699,7 @@ void bpf_jit_compile(struct bpf_prog *fp)
 void bpf_jit_free(struct bpf_prog *fp)
 {
 	if (fp->jited)
-		module_free(NULL, fp->bpf_func);
+		module_memfree(fp->bpf_func);
 
 	bpf_prog_unlock_free(fp);
 }

arch/s390/kernel/module.c

@@ -55,14 +55,10 @@ void *module_alloc(unsigned long size)
 }
 #endif
 
-/* Free memory returned from module_alloc */
-void module_free(struct module *mod, void *module_region)
+void module_arch_freeing_init(struct module *mod)
 {
-	if (mod) {
-		vfree(mod->arch.syminfo);
-		mod->arch.syminfo = NULL;
-	}
-	vfree(module_region);
+	vfree(mod->arch.syminfo);
+	mod->arch.syminfo = NULL;
 }
 
 static void check_rela(Elf_Rela *rela, struct module *me)

arch/s390/net/bpf_jit.S

@@ -22,8 +22,8 @@
  * skb_copy_bits takes 4 parameters:
  *   %r2 = skb pointer
  *   %r3 = offset into skb data
- *   %r4 = length to copy
- *   %r5 = pointer to temp buffer
+ *   %r4 = pointer to temp buffer
+ *   %r5 = length to copy
  */
 #define SKBDATA	%r8
 
@@ -44,8 +44,9 @@ ENTRY(sk_load_word)
 
 sk_load_word_slow:
 	lgr	%r9,%r2			# save %r2
-	lhi	%r4,4			# 4 bytes
-	la	%r5,160(%r15)		# pointer to temp buffer
+	lgr	%r3,%r1			# offset
+	la	%r4,160(%r15)		# pointer to temp buffer
+	lghi	%r5,4			# 4 bytes
 	brasl	%r14,skb_copy_bits	# get data from skb
 	l	%r5,160(%r15)		# load result from temp buffer
 	ltgr	%r2,%r2			# set cc to (%r2 != 0)
@@ -69,8 +70,9 @@ ENTRY(sk_load_half)
 
 sk_load_half_slow:
 	lgr	%r9,%r2			# save %r2
-	lhi	%r4,2			# 2 bytes
-	la	%r5,162(%r15)		# pointer to temp buffer
+	lgr	%r3,%r1			# offset
+	la	%r4,162(%r15)		# pointer to temp buffer
+	lghi	%r5,2			# 2 bytes
 	brasl	%r14,skb_copy_bits	# get data from skb
 	xc	160(2,%r15),160(%r15)
 	l	%r5,160(%r15)		# load result from temp buffer
@@ -95,8 +97,9 @@ ENTRY(sk_load_byte)
 
 sk_load_byte_slow:
 	lgr	%r9,%r2			# save %r2
-	lhi	%r4,1			# 1 bytes
-	la	%r5,163(%r15)		# pointer to temp buffer
+	lgr	%r3,%r1			# offset
+	la	%r4,163(%r15)		# pointer to temp buffer
+	lghi	%r5,1			# 1 byte
 	brasl	%r14,skb_copy_bits	# get data from skb
 	xc	160(3,%r15),160(%r15)
 	l	%r5,160(%r15)		# load result from temp buffer
@@ -104,11 +107,11 @@ sk_load_byte_slow:
 	lgr	%r2,%r9			# restore %r2
 	br	%r8
 
-	/* A = (*(u8 *)(skb->data+K) & 0xf) << 2 */
+	/* X = (*(u8 *)(skb->data+K) & 0xf) << 2 */
 ENTRY(sk_load_byte_msh)
 	llgfr	%r1,%r3			# extend offset
 	clr	%r11,%r3		# hlen < offset ?
-	jle	sk_load_byte_slow
+	jle	sk_load_byte_msh_slow
 	lhi	%r12,0
 	ic	%r12,0(%r1,%r10)	# get byte from skb
 	nill	%r12,0x0f
@@ -118,8 +121,9 @@ ENTRY(sk_load_byte_msh)
 
 sk_load_byte_msh_slow:
 	lgr	%r9,%r2			# save %r2
-	lhi	%r4,2			# 2 bytes
-	la	%r5,162(%r15)		# pointer to temp buffer
+	lgr	%r3,%r1			# offset
+	la	%r4,163(%r15)		# pointer to temp buffer
+	lghi	%r5,1			# 1 byte
 	brasl	%r14,skb_copy_bits	# get data from skb
 	xc	160(3,%r15),160(%r15)
 	l	%r12,160(%r15)		# load result from temp buffer

arch/s390/net/bpf_jit_comp.c

@@ -448,15 +448,12 @@ static int bpf_jit_insn(struct bpf_jit *jit, struct sock_filter *filter,
 		mask = 0x800000; /* je */
 kbranch:	/* Emit compare if the branch targets are different */
 		if (filter->jt != filter->jf) {
-			if (K <= 16383)
-				/* chi %r5,<K> */
-				EMIT4_IMM(0xa75e0000, K);
-			else if (test_facility(21))
+			if (test_facility(21))
 				/* clfi %r5,<K> */
 				EMIT6_IMM(0xc25f0000, K);
 			else
-				/* c %r5,<d(K)>(%r13) */
-				EMIT4_DISP(0x5950d000, EMIT_CONST(K));
+				/* cl %r5,<d(K)>(%r13) */
+				EMIT4_DISP(0x5550d000, EMIT_CONST(K));
 		}
 branch:		if (filter->jt == filter->jf) {
 			if (filter->jt == 0)

arch/sparc/kernel/pci.c

@@ -639,7 +639,10 @@ static void pci_claim_bus_resources(struct pci_bus *bus)
 				       (unsigned long long)r->end,
 				       (unsigned int)r->flags);
 
-			pci_claim_resource(dev, i);
+			if (pci_claim_resource(dev, i) == 0)
+				continue;
+
+			pci_claim_bridge_resource(dev, i);
 		}
 	}
 

arch/sparc/net/bpf_jit_comp.c

@@ -776,7 +776,7 @@ cond_branch:			f_offset = addrs[i + filter[i].jf];
 				if (unlikely(proglen + ilen > oldproglen)) {
 					pr_err("bpb_jit_compile fatal error\n");
 					kfree(addrs);
-					module_free(NULL, image);
+					module_memfree(image);
 					return;
 				}
 				memcpy(image + proglen, temp, ilen);
@@ -822,7 +822,7 @@ cond_branch:			f_offset = addrs[i + filter[i].jf];
 void bpf_jit_free(struct bpf_prog *fp)
 {
 	if (fp->jited)
-		module_free(NULL, fp->bpf_func);
+		module_memfree(fp->bpf_func);
 
 	bpf_prog_unlock_free(fp);
 }

arch/tile/kernel/module.c

@@ -74,7 +74,7 @@ void *module_alloc(unsigned long size)
 
 
 /* Free memory returned from module_alloc */
-void module_free(struct module *mod, void *module_region)
+void module_memfree(void *module_region)
 {
 	vfree(module_region);
 
@@ -83,7 +83,7 @@ void module_free(struct module *mod, void *module_region)
 		     0, 0, 0, NULL, NULL, 0);
 
 	/*
-	 * FIXME: If module_region == mod->module_init, trim exception
+	 * FIXME: Add module_arch_freeing_init to trim exception
 	 * table entries.
 	 */
 }

arch/x86/Kconfig

@@ -857,7 +857,7 @@ source "kernel/Kconfig.preempt"
 
 config X86_UP_APIC
 	bool "Local APIC support on uniprocessors"
-	depends on X86_32 && !SMP && !X86_32_NON_STANDARD && !PCI_MSI
+	depends on X86_32 && !SMP && !X86_32_NON_STANDARD
 	---help---
 	  A local APIC (Advanced Programmable Interrupt Controller) is an
 	  integrated interrupt controller in the CPU. If you have a single-CPU
@@ -868,6 +868,10 @@ config X86_UP_APIC
 	  performance counters), and the NMI watchdog which detects hard
 	  lockups.
 
+config X86_UP_APIC_MSI
+	def_bool y
+	select X86_UP_APIC if X86_32 && !SMP && !X86_32_NON_STANDARD && PCI_MSI
+
 config X86_UP_IOAPIC
 	bool "IO-APIC support on uniprocessors"
 	depends on X86_UP_APIC

arch/x86/boot/compressed/misc.c

@@ -373,6 +373,8 @@ asmlinkage __visible void *decompress_kernel(void *rmode, memptr heap,
 				  unsigned long output_len,
 				  unsigned long run_size)
 {
+	unsigned char *output_orig = output;
+
 	real_mode = rmode;
 
 	sanitize_boot_params(real_mode);
@@ -421,7 +423,12 @@ asmlinkage __visible void *decompress_kernel(void *rmode, memptr heap,
 	debug_putstr("\nDecompressing Linux... ");
 	decompress(input_data, input_len, NULL, NULL, output, NULL, error);
 	parse_elf(output);
-	handle_relocations(output, output_len);
+	/*
+	 * 32-bit always performs relocations. 64-bit relocations are only
+	 * needed if kASLR has chosen a different load address.
+	 */
+	if (!IS_ENABLED(CONFIG_X86_64) || output != output_orig)
+		handle_relocations(output, output_len);
 	debug_putstr("done.\nBooting the kernel.\n");
 	return output;
 }

arch/x86/crypto/sha-mb/sha1_mb.c

@@ -931,4 +931,4 @@ module_exit(sha1_mb_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("SHA1 Secure Hash Algorithm, multi buffer accelerated");
 
-MODULE_ALIAS("sha1");
+MODULE_ALIAS_CRYPTO("sha1");

arch/x86/include/asm/acpi.h

@@ -50,6 +50,7 @@ void acpi_pic_sci_set_trigger(unsigned int, u16);
 
 extern int (*__acpi_register_gsi)(struct device *dev, u32 gsi,
 				  int trigger, int polarity);
+extern void (*__acpi_unregister_gsi)(u32 gsi);
 
 static inline void disable_acpi(void)
 {

arch/x86/include/asm/desc.h

@@ -251,7 +251,8 @@ static inline void native_load_tls(struct thread_struct *t, unsigned int cpu)
 		gdt[GDT_ENTRY_TLS_MIN + i] = t->tls_array[i];
 }
 
-#define _LDT_empty(info)				\
+/* This intentionally ignores lm, since 32-bit apps don't have that field. */
+#define LDT_empty(info)					\
 	((info)->base_addr		== 0	&&	\
 	 (info)->limit			== 0	&&	\
 	 (info)->contents		== 0	&&	\
@@ -261,11 +262,18 @@ static inline void native_load_tls(struct thread_struct *t, unsigned int cpu)
 	 (info)->seg_not_present	== 1	&&	\
 	 (info)->useable		== 0)
 
-#ifdef CONFIG_X86_64
-#define LDT_empty(info) (_LDT_empty(info) && ((info)->lm == 0))
-#else
-#define LDT_empty(info) (_LDT_empty(info))
-#endif
+/* Lots of programs expect an all-zero user_desc to mean "no segment at all". */
+static inline bool LDT_zero(const struct user_desc *info)
+{
+	return (info->base_addr		== 0 &&
+		info->limit		== 0 &&
+		info->contents		== 0 &&
+		info->read_exec_only	== 0 &&
+		info->seg_32bit		== 0 &&
+		info->limit_in_pages	== 0 &&
+		info->seg_not_present	== 0 &&
+		info->useable		== 0);
+}
 
 static inline void clear_LDT(void)
 {

arch/x86/include/asm/mmu_context.h

@@ -130,7 +130,25 @@ static inline void arch_bprm_mm_init(struct mm_struct *mm,
 static inline void arch_unmap(struct mm_struct *mm, struct vm_area_struct *vma,
 			      unsigned long start, unsigned long end)
 {
-	mpx_notify_unmap(mm, vma, start, end);
+	/*
+	 * mpx_notify_unmap() goes and reads a rarely-hot
+	 * cacheline in the mm_struct.  That can be expensive
+	 * enough to be seen in profiles.
+	 *
+	 * The mpx_notify_unmap() call and its contents have been
+	 * observed to affect munmap() performance on hardware
+	 * where MPX is not present.
+	 *
+	 * The unlikely() optimizes for the fast case: no MPX
+	 * in the CPU, or no MPX use in the process.  Even if
+	 * we get this wrong (in the unlikely event that MPX
+	 * is widely enabled on some system) the overhead of
+	 * MPX itself (reading bounds tables) is expected to
+	 * overwhelm the overhead of getting this unlikely()
+	 * consistently wrong.
+	 */
+	if (unlikely(cpu_feature_enabled(X86_FEATURE_MPX)))
+		mpx_notify_unmap(mm, vma, start, end);
 }
 
 #endif /* _ASM_X86_MMU_CONTEXT_H */

arch/x86/kernel/acpi/boot.c

@@ -611,20 +611,20 @@ void __init acpi_pic_sci_set_trigger(unsigned int irq, u16 trigger)
 
 int acpi_gsi_to_irq(u32 gsi, unsigned int *irqp)
 {
-	int irq;
-
-	if (acpi_irq_model == ACPI_IRQ_MODEL_PIC) {
-		*irqp = gsi;
-	} else {
-		mutex_lock(&acpi_ioapic_lock);
-		irq = mp_map_gsi_to_irq(gsi,
-					IOAPIC_MAP_ALLOC | IOAPIC_MAP_CHECK);
-		mutex_unlock(&acpi_ioapic_lock);
-		if (irq < 0)
-			return -1;
-		*irqp = irq;
+	int rc, irq, trigger, polarity;
+
+	rc = acpi_get_override_irq(gsi, &trigger, &polarity);
+	if (rc == 0) {
+		trigger = trigger ? ACPI_LEVEL_SENSITIVE : ACPI_EDGE_SENSITIVE;
+		polarity = polarity ? ACPI_ACTIVE_LOW : ACPI_ACTIVE_HIGH;
+		irq = acpi_register_gsi(NULL, gsi, trigger, polarity);
+		if (irq >= 0) {
+			*irqp = irq;
+			return 0;
+		}
 	}
-	return 0;
+
+	return -1;
 }
 EXPORT_SYMBOL_GPL(acpi_gsi_to_irq);
 

arch/x86/kernel/cpu/mshyperv.c

@@ -107,6 +107,7 @@ static struct clocksource hyperv_cs = {
 	.rating		= 400, /* use this when running on Hyperv*/
 	.read		= read_hv_clock,
 	.mask		= CLOCKSOURCE_MASK(64),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
 };
 
 static void __init ms_hyperv_init_platform(void)

arch/x86/kernel/ftrace.c

@@ -674,7 +674,7 @@ static inline void *alloc_tramp(unsigned long size)
 }
 static inline void tramp_free(void *tramp)
 {
-	module_free(NULL, tramp);
+	module_memfree(tramp);
 }
 #else
 /* Trampolines can only be created if modules are supported */

arch/x86/kernel/irq.c

@@ -127,7 +127,7 @@ int arch_show_interrupts(struct seq_file *p, int prec)
 	seq_puts(p, "  Machine check polls\n");
 #endif
 #if IS_ENABLED(CONFIG_HYPERV) || defined(CONFIG_XEN)
-	seq_printf(p, "%*s: ", prec, "THR");
+	seq_printf(p, "%*s: ", prec, "HYP");
 	for_each_online_cpu(j)
 		seq_printf(p, "%10u ", irq_stats(j)->irq_hv_callback_count);
 	seq_puts(p, "  Hypervisor callback interrupts\n");

arch/x86/kernel/tls.c

@@ -29,7 +29,28 @@ static int get_free_idx(void)
 
 static bool tls_desc_okay(const struct user_desc *info)
 {
-	if (LDT_empty(info))
+	/*
+	 * For historical reasons (i.e. no one ever documented how any
+	 * of the segmentation APIs work), user programs can and do
+	 * assume that a struct user_desc that's all zeros except for
+	 * entry_number means "no segment at all".  This never actually
+	 * worked.  In fact, up to Linux 3.19, a struct user_desc like
+	 * this would create a 16-bit read-write segment with base and
+	 * limit both equal to zero.
+	 *
+	 * That was close enough to "no segment at all" until we
+	 * hardened this function to disallow 16-bit TLS segments.  Fix
+	 * it up by interpreting these zeroed segments the way that they
+	 * were almost certainly intended to be interpreted.
+	 *
+	 * The correct way to ask for "no segment at all" is to specify
+	 * a user_desc that satisfies LDT_empty.  To keep everything
+	 * working, we accept both.
+	 *
+	 * Note that there's a similar kludge in modify_ldt -- look at
+	 * the distinction between modes 1 and 0x11.
+	 */
+	if (LDT_empty(info) || LDT_zero(info))
 		return true;
 
 	/*
@@ -71,7 +92,7 @@ static void set_tls_desc(struct task_struct *p, int idx,
 	cpu = get_cpu();
 
 	while (n-- > 0) {
-		if (LDT_empty(info))
+		if (LDT_empty(info) || LDT_zero(info))
 			desc->a = desc->b = 0;
 		else
 			fill_ldt(desc, info);

arch/x86/kernel/tsc.c

@@ -617,7 +617,7 @@ static unsigned long quick_pit_calibrate(void)
 			goto success;
 		}
 	}
-	pr_err("Fast TSC calibration failed\n");
+	pr_info("Fast TSC calibration failed\n");
 	return 0;
 
 success:

arch/x86/kvm/emulate.c

@@ -2348,7 +2348,7 @@ static int em_sysenter(struct x86_emulate_ctxt *ctxt)
 	 * Not recognized on AMD in compat mode (but is recognized in legacy
 	 * mode).
 	 */
-	if ((ctxt->mode == X86EMUL_MODE_PROT32) && (efer & EFER_LMA)
+	if ((ctxt->mode != X86EMUL_MODE_PROT64) && (efer & EFER_LMA)
 	    && !vendor_intel(ctxt))
 		return emulate_ud(ctxt);
 
@@ -2359,25 +2359,13 @@ static int em_sysenter(struct x86_emulate_ctxt *ctxt)
 	setup_syscalls_segments(ctxt, &cs, &ss);
 
 	ops->get_msr(ctxt, MSR_IA32_SYSENTER_CS, &msr_data);
-	switch (ctxt->mode) {
-	case X86EMUL_MODE_PROT32:
-		if ((msr_data & 0xfffc) == 0x0)
-			return emulate_gp(ctxt, 0);
-		break;
-	case X86EMUL_MODE_PROT64:
-		if (msr_data == 0x0)
-			return emulate_gp(ctxt, 0);
-		break;
-	default:
-		break;
-	}
+	if ((msr_data & 0xfffc) == 0x0)
+		return emulate_gp(ctxt, 0);
 
 	ctxt->eflags &= ~(EFLG_VM | EFLG_IF);
-	cs_sel = (u16)msr_data;
-	cs_sel &= ~SELECTOR_RPL_MASK;
+	cs_sel = (u16)msr_data & ~SELECTOR_RPL_MASK;
 	ss_sel = cs_sel + 8;
-	ss_sel &= ~SELECTOR_RPL_MASK;
-	if (ctxt->mode == X86EMUL_MODE_PROT64 || (efer & EFER_LMA)) {
+	if (efer & EFER_LMA) {
 		cs.d = 0;
 		cs.l = 1;
 	}
@@ -2386,10 +2374,11 @@ static int em_sysenter(struct x86_emulate_ctxt *ctxt)
 	ops->set_segment(ctxt, ss_sel, &ss, 0, VCPU_SREG_SS);
 
 	ops->get_msr(ctxt, MSR_IA32_SYSENTER_EIP, &msr_data);
-	ctxt->_eip = msr_data;
+	ctxt->_eip = (efer & EFER_LMA) ? msr_data : (u32)msr_data;
 
 	ops->get_msr(ctxt, MSR_IA32_SYSENTER_ESP, &msr_data);
-	*reg_write(ctxt, VCPU_REGS_RSP) = msr_data;
+	*reg_write(ctxt, VCPU_REGS_RSP) = (efer & EFER_LMA) ? msr_data :
+							      (u32)msr_data;
 
 	return X86EMUL_CONTINUE;
 }
@@ -3791,8 +3780,8 @@ static const struct opcode group5[] = {
 };
 
 static const struct opcode group6[] = {
-	DI(Prot,	sldt),
-	DI(Prot,	str),
+	DI(Prot | DstMem,	sldt),
+	DI(Prot | DstMem,	str),
 	II(Prot | Priv | SrcMem16, em_lldt, lldt),
 	II(Prot | Priv | SrcMem16, em_ltr, ltr),
 	N, N, N, N,

arch/x86/mm/init.c

@@ -43,7 +43,7 @@ uint16_t __cachemode2pte_tbl[_PAGE_CACHE_MODE_NUM] = {
 	[_PAGE_CACHE_MODE_WT]		= _PAGE_PCD,
 	[_PAGE_CACHE_MODE_WP]		= _PAGE_PCD,
 };
-EXPORT_SYMBOL_GPL(__cachemode2pte_tbl);
+EXPORT_SYMBOL(__cachemode2pte_tbl);
 uint8_t __pte2cachemode_tbl[8] = {
 	[__pte2cm_idx(0)] = _PAGE_CACHE_MODE_WB,
 	[__pte2cm_idx(_PAGE_PWT)] = _PAGE_CACHE_MODE_WC,
@@ -54,7 +54,7 @@ uint8_t __pte2cachemode_tbl[8] = {
 	[__pte2cm_idx(_PAGE_PCD | _PAGE_PAT)] = _PAGE_CACHE_MODE_UC_MINUS,
 	[__pte2cm_idx(_PAGE_PWT | _PAGE_PCD | _PAGE_PAT)] = _PAGE_CACHE_MODE_UC,
 };
-EXPORT_SYMBOL_GPL(__pte2cachemode_tbl);
+EXPORT_SYMBOL(__pte2cachemode_tbl);
 
 static unsigned long __initdata pgt_buf_start;
 static unsigned long __initdata pgt_buf_end;

arch/x86/mm/mpx.c

@@ -348,6 +348,12 @@ static __user void *task_get_bounds_dir(struct task_struct *tsk)
 	if (!cpu_feature_enabled(X86_FEATURE_MPX))
 		return MPX_INVALID_BOUNDS_DIR;
 
+	/*
+	 * 32-bit binaries on 64-bit kernels are currently
+	 * unsupported.
+	 */
+	if (IS_ENABLED(CONFIG_X86_64) && test_thread_flag(TIF_IA32))
+		return MPX_INVALID_BOUNDS_DIR;
 	/*
 	 * The bounds directory pointer is stored in a register
 	 * only accessible if we first do an xsave.

arch/x86/mm/pat.c

@@ -234,8 +234,13 @@ void pat_init(void)
 	      PAT(4, WB) | PAT(5, WC) | PAT(6, UC_MINUS) | PAT(7, UC);
 
 	/* Boot CPU check */
-	if (!boot_pat_state)
+	if (!boot_pat_state) {
 		rdmsrl(MSR_IA32_CR_PAT, boot_pat_state);
+		if (!boot_pat_state) {
+			pat_disable("PAT read returns always zero, disabled.");
+			return;
+		}
+	}
 
 	wrmsrl(MSR_IA32_CR_PAT, pat);
 

arch/x86/pci/i386.c

@@ -216,7 +216,7 @@ static void pcibios_allocate_bridge_resources(struct pci_dev *dev)
 			continue;
 		if (r->parent)	/* Already allocated */
 			continue;
-		if (!r->start || pci_claim_resource(dev, idx) < 0) {
+		if (!r->start || pci_claim_bridge_resource(dev, idx) < 0) {
 			/*
 			 * Something is wrong with the region.
 			 * Invalidate the resource to prevent

arch/x86/pci/xen.c

@@ -458,6 +458,7 @@ int __init pci_xen_hvm_init(void)
 	 * just how GSIs get registered.
 	 */
 	__acpi_register_gsi = acpi_register_gsi_xen_hvm;
+	__acpi_unregister_gsi = NULL;
 #endif
 
 #ifdef CONFIG_PCI_MSI
@@ -471,52 +472,6 @@ int __init pci_xen_hvm_init(void)
 }
 
 #ifdef CONFIG_XEN_DOM0
-static __init void xen_setup_acpi_sci(void)
-{
-	int rc;
-	int trigger, polarity;
-	int gsi = acpi_sci_override_gsi;
-	int irq = -1;
-	int gsi_override = -1;
-
-	if (!gsi)
-		return;
-
-	rc = acpi_get_override_irq(gsi, &trigger, &polarity);
-	if (rc) {
-		printk(KERN_WARNING "xen: acpi_get_override_irq failed for acpi"
-				" sci, rc=%d\n", rc);
-		return;
-	}
-	trigger = trigger ? ACPI_LEVEL_SENSITIVE : ACPI_EDGE_SENSITIVE;
-	polarity = polarity ? ACPI_ACTIVE_LOW : ACPI_ACTIVE_HIGH;
-
-	printk(KERN_INFO "xen: sci override: global_irq=%d trigger=%d "
-			"polarity=%d\n", gsi, trigger, polarity);
-
-	/* Before we bind the GSI to a Linux IRQ, check whether
-	 * we need to override it with bus_irq (IRQ) value. Usually for
-	 * IRQs below IRQ_LEGACY_IRQ this holds IRQ == GSI, as so:
-	 *  ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
-	 * but there are oddballs where the IRQ != GSI:
-	 *  ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
-	 * which ends up being: gsi_to_irq[9] == 20
-	 * (which is what acpi_gsi_to_irq ends up calling when starting the
-	 * the ACPI interpreter and keels over since IRQ 9 has not been
-	 * setup as we had setup IRQ 20 for it).
-	 */
-	if (acpi_gsi_to_irq(gsi, &irq) == 0) {
-		/* Use the provided value if it's valid. */
-		if (irq >= 0)
-			gsi_override = irq;
-	}
-
-	gsi = xen_register_gsi(gsi, gsi_override, trigger, polarity);
-	printk(KERN_INFO "xen: acpi sci %d\n", gsi);
-
-	return;
-}
-
 int __init pci_xen_initial_domain(void)
 {
 	int irq;
@@ -527,8 +482,8 @@ int __init pci_xen_initial_domain(void)
 	x86_msi.restore_msi_irqs = xen_initdom_restore_msi_irqs;
 	pci_msi_ignore_mask = 1;
 #endif
-	xen_setup_acpi_sci();
 	__acpi_register_gsi = acpi_register_gsi_xen;
+	__acpi_unregister_gsi = NULL;
 	/* Pre-allocate legacy irqs */
 	for (irq = 0; irq < nr_legacy_irqs(); irq++) {
 		int trigger, polarity;

block/blk-mq-sysfs.c

@@ -15,6 +15,26 @@
 
 static void blk_mq_sysfs_release(struct kobject *kobj)
 {
+	struct request_queue *q;
+
+	q = container_of(kobj, struct request_queue, mq_kobj);
+	free_percpu(q->queue_ctx);
+}
+
+static void blk_mq_ctx_release(struct kobject *kobj)
+{
+	struct blk_mq_ctx *ctx;
+
+	ctx = container_of(kobj, struct blk_mq_ctx, kobj);
+	kobject_put(&ctx->queue->mq_kobj);
+}
+
+static void blk_mq_hctx_release(struct kobject *kobj)
+{
+	struct blk_mq_hw_ctx *hctx;
+
+	hctx = container_of(kobj, struct blk_mq_hw_ctx, kobj);
+	kfree(hctx);
 }
 
 struct blk_mq_ctx_sysfs_entry {
@@ -318,13 +338,13 @@ static struct kobj_type blk_mq_ktype = {
 static struct kobj_type blk_mq_ctx_ktype = {
 	.sysfs_ops	= &blk_mq_sysfs_ops,
 	.default_attrs	= default_ctx_attrs,
-	.release	= blk_mq_sysfs_release,
+	.release	= blk_mq_ctx_release,
 };
 
 static struct kobj_type blk_mq_hw_ktype = {
 	.sysfs_ops	= &blk_mq_hw_sysfs_ops,
 	.default_attrs	= default_hw_ctx_attrs,
-	.release	= blk_mq_sysfs_release,
+	.release	= blk_mq_hctx_release,
 };
 
 static void blk_mq_unregister_hctx(struct blk_mq_hw_ctx *hctx)
@@ -355,6 +375,7 @@ static int blk_mq_register_hctx(struct blk_mq_hw_ctx *hctx)
 		return ret;
 
 	hctx_for_each_ctx(hctx, ctx, i) {
+		kobject_get(&q->mq_kobj);
 		ret = kobject_add(&ctx->kobj, &hctx->kobj, "cpu%u", ctx->cpu);
 		if (ret)
 			break;

block/blk-mq.c

@@ -1641,10 +1641,8 @@ static void blk_mq_free_hw_queues(struct request_queue *q,
 	struct blk_mq_hw_ctx *hctx;
 	unsigned int i;
 
-	queue_for_each_hw_ctx(q, hctx, i) {
+	queue_for_each_hw_ctx(q, hctx, i)
 		free_cpumask_var(hctx->cpumask);
-		kfree(hctx);
-	}
 }
 
 static int blk_mq_init_hctx(struct request_queue *q,
@@ -2002,11 +2000,9 @@ void blk_mq_free_queue(struct request_queue *q)
 
 	percpu_ref_exit(&q->mq_usage_counter);
 
-	free_percpu(q->queue_ctx);
 	kfree(q->queue_hw_ctx);
 	kfree(q->mq_map);
 
-	q->queue_ctx = NULL;
 	q->queue_hw_ctx = NULL;
 	q->mq_map = NULL;
 

crypto/aes_generic.c

@@ -1475,3 +1475,4 @@ module_exit(aes_fini);
 MODULE_DESCRIPTION("Rijndael (AES) Cipher Algorithm");
 MODULE_LICENSE("Dual BSD/GPL");
 MODULE_ALIAS_CRYPTO("aes");
+MODULE_ALIAS_CRYPTO("aes-generic");

crypto/ansi_cprng.c

@@ -477,3 +477,4 @@ MODULE_PARM_DESC(dbg, "Boolean to enable debugging (0/1 == off/on)");
 module_init(prng_mod_init);
 module_exit(prng_mod_fini);
 MODULE_ALIAS_CRYPTO("stdrng");
+MODULE_ALIAS_CRYPTO("ansi_cprng");

crypto/blowfish_generic.c

@@ -139,3 +139,4 @@ module_exit(blowfish_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Blowfish Cipher Algorithm");
 MODULE_ALIAS_CRYPTO("blowfish");
+MODULE_ALIAS_CRYPTO("blowfish-generic");

crypto/camellia_generic.c

@@ -1099,3 +1099,4 @@ module_exit(camellia_fini);
 MODULE_DESCRIPTION("Camellia Cipher Algorithm");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS_CRYPTO("camellia");
+MODULE_ALIAS_CRYPTO("camellia-generic");

crypto/cast5_generic.c

@@ -550,3 +550,4 @@ module_exit(cast5_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Cast5 Cipher Algorithm");
 MODULE_ALIAS_CRYPTO("cast5");
+MODULE_ALIAS_CRYPTO("cast5-generic");

crypto/cast6_generic.c

@@ -292,3 +292,4 @@ module_exit(cast6_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Cast6 Cipher Algorithm");
 MODULE_ALIAS_CRYPTO("cast6");
+MODULE_ALIAS_CRYPTO("cast6-generic");

crypto/crc32c_generic.c

@@ -171,4 +171,5 @@ MODULE_AUTHOR("Clay Haapala <chaapala@cisco.com>");
 MODULE_DESCRIPTION("CRC32c (Castagnoli) calculations wrapper for lib/crc32c");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS_CRYPTO("crc32c");
+MODULE_ALIAS_CRYPTO("crc32c-generic");
 MODULE_SOFTDEP("pre: crc32c");

crypto/crct10dif_generic.c

@@ -125,3 +125,4 @@ MODULE_AUTHOR("Tim Chen <tim.c.chen@linux.intel.com>");
 MODULE_DESCRIPTION("T10 DIF CRC calculation.");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS_CRYPTO("crct10dif");
+MODULE_ALIAS_CRYPTO("crct10dif-generic");

crypto/des_generic.c

@@ -983,8 +983,6 @@ static struct crypto_alg des_algs[2] = { {
 	.cia_decrypt		=	des3_ede_decrypt } }
 } };
 
-MODULE_ALIAS_CRYPTO("des3_ede");
-
 static int __init des_generic_mod_init(void)
 {
 	return crypto_register_algs(des_algs, ARRAY_SIZE(des_algs));
@@ -1001,4 +999,7 @@ module_exit(des_generic_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("DES & Triple DES EDE Cipher Algorithms");
 MODULE_AUTHOR("Dag Arne Osvik <da@osvik.no>");
-MODULE_ALIAS("des");
+MODULE_ALIAS_CRYPTO("des");
+MODULE_ALIAS_CRYPTO("des-generic");
+MODULE_ALIAS_CRYPTO("des3_ede");
+MODULE_ALIAS_CRYPTO("des3_ede-generic");

crypto/ghash-generic.c

@@ -173,3 +173,4 @@ module_exit(ghash_mod_exit);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("GHASH Message Digest Algorithm");
 MODULE_ALIAS_CRYPTO("ghash");
+MODULE_ALIAS_CRYPTO("ghash-generic");

crypto/krng.c

@@ -63,3 +63,4 @@ module_exit(krng_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Kernel Random Number Generator");
 MODULE_ALIAS_CRYPTO("stdrng");
+MODULE_ALIAS_CRYPTO("krng");

crypto/salsa20_generic.c

@@ -249,3 +249,4 @@ module_exit(salsa20_generic_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION ("Salsa20 stream cipher algorithm");
 MODULE_ALIAS_CRYPTO("salsa20");
+MODULE_ALIAS_CRYPTO("salsa20-generic");

crypto/serpent_generic.c

@@ -667,3 +667,4 @@ MODULE_DESCRIPTION("Serpent and tnepres (kerneli compatible serpent reversed) Ci
 MODULE_AUTHOR("Dag Arne Osvik <osvik@ii.uib.no>");
 MODULE_ALIAS_CRYPTO("tnepres");
 MODULE_ALIAS_CRYPTO("serpent");
+MODULE_ALIAS_CRYPTO("serpent-generic");

crypto/sha1_generic.c

@@ -154,3 +154,4 @@ MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("SHA1 Secure Hash Algorithm");
 
 MODULE_ALIAS_CRYPTO("sha1");
+MODULE_ALIAS_CRYPTO("sha1-generic");

crypto/sha256_generic.c

@@ -385,4 +385,6 @@ MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("SHA-224 and SHA-256 Secure Hash Algorithm");
 
 MODULE_ALIAS_CRYPTO("sha224");
+MODULE_ALIAS_CRYPTO("sha224-generic");
 MODULE_ALIAS_CRYPTO("sha256");
+MODULE_ALIAS_CRYPTO("sha256-generic");

crypto/sha512_generic.c

@@ -289,4 +289,6 @@ MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("SHA-512 and SHA-384 Secure Hash Algorithms");
 
 MODULE_ALIAS_CRYPTO("sha384");
+MODULE_ALIAS_CRYPTO("sha384-generic");
 MODULE_ALIAS_CRYPTO("sha512");
+MODULE_ALIAS_CRYPTO("sha512-generic");

crypto/tea.c

@@ -270,6 +270,7 @@ static void __exit tea_mod_fini(void)
 	crypto_unregister_algs(tea_algs, ARRAY_SIZE(tea_algs));
 }
 
+MODULE_ALIAS_CRYPTO("tea");
 MODULE_ALIAS_CRYPTO("xtea");
 MODULE_ALIAS_CRYPTO("xeta");
 

crypto/tgr192.c

@@ -676,6 +676,7 @@ static void __exit tgr192_mod_fini(void)
 	crypto_unregister_shashes(tgr_algs, ARRAY_SIZE(tgr_algs));
 }
 
+MODULE_ALIAS_CRYPTO("tgr192");
 MODULE_ALIAS_CRYPTO("tgr160");
 MODULE_ALIAS_CRYPTO("tgr128");
 

crypto/twofish_generic.c

@@ -212,3 +212,4 @@ module_exit(twofish_mod_fini);
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION ("Twofish Cipher Algorithm");
 MODULE_ALIAS_CRYPTO("twofish");
+MODULE_ALIAS_CRYPTO("twofish-generic");

crypto/wp512.c

@@ -1167,6 +1167,7 @@ static void __exit wp512_mod_fini(void)
 	crypto_unregister_shashes(wp_algs, ARRAY_SIZE(wp_algs));
 }
 
+MODULE_ALIAS_CRYPTO("wp512");
 MODULE_ALIAS_CRYPTO("wp384");
 MODULE_ALIAS_CRYPTO("wp256");
 

drivers/acpi/pci_irq.c

@@ -512,7 +512,6 @@ void acpi_pci_irq_disable(struct pci_dev *dev)
 	dev_dbg(&dev->dev, "PCI INT %c disabled\n", pin_name(pin));
 	if (gsi >= 0) {
 		acpi_unregister_gsi(gsi);
-		dev->irq = 0;
 		dev->irq_managed = 0;
 	}
 }

drivers/ata/Kconfig

@@ -835,6 +835,7 @@ config PATA_AT32
 config PATA_AT91
 	tristate "PATA support for AT91SAM9260"
 	depends on ARM && SOC_AT91SAM9
+	depends on !ARCH_MULTIPLATFORM
 	help
 	  This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
 

drivers/ata/ahci.c

@@ -325,7 +325,6 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x9d05), board_ahci }, /* Sunrise Point-LP RAID */
 	{ PCI_VDEVICE(INTEL, 0x9d07), board_ahci }, /* Sunrise Point-LP RAID */
 	{ PCI_VDEVICE(INTEL, 0xa103), board_ahci }, /* Sunrise Point-H AHCI */
-	{ PCI_VDEVICE(INTEL, 0xa103), board_ahci }, /* Sunrise Point-H RAID */
 	{ PCI_VDEVICE(INTEL, 0xa105), board_ahci }, /* Sunrise Point-H RAID */
 	{ PCI_VDEVICE(INTEL, 0xa107), board_ahci }, /* Sunrise Point-H RAID */
 	{ PCI_VDEVICE(INTEL, 0xa10f), board_ahci }, /* Sunrise Point-H RAID */

drivers/ata/ahci_xgene.c

@@ -125,10 +125,11 @@ static int xgene_ahci_restart_engine(struct ata_port *ap)
  * xgene_ahci_qc_issue - Issue commands to the device
  * @qc: Command to issue
  *
- * Due to Hardware errata for IDENTIFY DEVICE command, the controller cannot
- * clear the BSY bit after receiving the PIO setup FIS. This results in the dma
- * state machine goes into the CMFatalErrorUpdate state and locks up. By
- * restarting the dma engine, it removes the controller out of lock up state.
+ * Due to Hardware errata for IDENTIFY DEVICE command and PACKET
+ * command of ATAPI protocol set, the controller cannot clear the BSY bit
+ * after receiving the PIO setup FIS. This results in the DMA state machine
+ * going into the CMFatalErrorUpdate state and locks up. By restarting the
+ * DMA engine, it removes the controller out of lock up state.
  */
 static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc)
 {
@@ -137,7 +138,8 @@ static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc)
 	struct xgene_ahci_context *ctx = hpriv->plat_data;
 	int rc = 0;
 
-	if (unlikely(ctx->last_cmd[ap->port_no] == ATA_CMD_ID_ATA))
+	if (unlikely((ctx->last_cmd[ap->port_no] == ATA_CMD_ID_ATA) ||
+	    (ctx->last_cmd[ap->port_no] == ATA_CMD_PACKET)))
 		xgene_ahci_restart_engine(ap);
 
 	rc = ahci_qc_issue(qc);
@@ -188,7 +190,7 @@ static unsigned int xgene_ahci_read_id(struct ata_device *dev,
 	 *
 	 * Clear reserved bit 8 (DEVSLP bit) as we don't support DEVSLP
 	 */
-	id[ATA_ID_FEATURE_SUPP] &= ~(1 << 8);
+	id[ATA_ID_FEATURE_SUPP] &= cpu_to_le16(~(1 << 8));
 
 	return 0;
 }

drivers/ata/libahci.c

@@ -2003,7 +2003,7 @@ static void ahci_set_aggressive_devslp(struct ata_port *ap, bool sleep)
 
 	devslp = readl(port_mmio + PORT_DEVSLP);
 	if (!(devslp & PORT_DEVSLP_DSP)) {
-		dev_err(ap->host->dev, "port does not support device sleep\n");
+		dev_info(ap->host->dev, "port does not support device sleep\n");
 		return;
 	}