phy-sun4i-usb: Add support for the host usb-phys found on the H3 SoC

Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.
Signed-off-by: NReinder de Haan <patchesrdh@mveas.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>

Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt

@@ -9,6 +9,7 @@ Required properties:
   * allwinner,sun7i-a20-usb-phy
   * allwinner,sun8i-a23-usb-phy
   * allwinner,sun8i-a33-usb-phy
+  * allwinner,sun8i-h3-usb-phy
 - reg : a list of offset + length pairs
 - reg-names :
   * "phy_ctrl"

drivers/phy/phy-sun4i-usb.c

@@ -47,6 +47,9 @@
 #define REG_PHYBIST			0x08
 #define REG_PHYTUNE			0x0c
 #define REG_PHYCTL_A33			0x10
+#define REG_PHY_UNK_H3			0x20
+
+#define REG_PMU_UNK_H3			0x10
 
 #define PHYCTL_DATA			BIT(7)
 
@@ -80,7 +83,7 @@
 #define PHY_DISCON_TH_SEL		0x2a
 #define PHY_SQUELCH_DETECT		0x3c
 
-#define MAX_PHYS			3
+#define MAX_PHYS			4
 
 /*
  * Note do not raise the debounce time, we must report Vusb high within 100ms
@@ -92,6 +95,7 @@
 enum sun4i_usb_phy_type {
 	sun4i_a10_phy,
 	sun8i_a33_phy,
+	sun8i_h3_phy,
 };
 
 struct sun4i_usb_phy_cfg {
@@ -239,6 +243,7 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 	struct sun4i_usb_phy *phy = phy_get_drvdata(_phy);
 	struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
 	int ret;
+	u32 val;
 
 	ret = clk_prepare_enable(phy->clk);
 	if (ret)
@@ -250,16 +255,26 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 		return ret;
 	}
 
-	/* Enable USB 45 Ohm resistor calibration */
-	if (phy->index == 0)
-		sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
+	if (data->cfg->type == sun8i_h3_phy) {
+		if (phy->index == 0) {
+			val = readl(data->base + REG_PHY_UNK_H3);
+			writel(val & ~1, data->base + REG_PHY_UNK_H3);
+		}
+
+		val = readl(phy->pmu + REG_PMU_UNK_H3);
+		writel(val & ~2, phy->pmu + REG_PMU_UNK_H3);
+	} else {
+		/* Enable USB 45 Ohm resistor calibration */
+		if (phy->index == 0)
+			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
 
-	/* Adjust PHY's magnitude and rate */
-	sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
+		/* Adjust PHY's magnitude and rate */
+		sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
 
-	/* Disconnect threshold adjustment */
-	sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
-			    data->cfg->disc_thresh, 2);
+		/* Disconnect threshold adjustment */
+		sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
+				    data->cfg->disc_thresh, 2);
+	}
 
 	sun4i_usb_phy_passby(phy, 1);
 
@@ -726,6 +741,13 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
 	.dedicated_clocks = true,
 };
 
+static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
+	.num_phys = 4,
+	.type = sun8i_h3_phy,
+	.disc_thresh = 3,
+	.dedicated_clocks = true,
+};
+
 static const struct of_device_id sun4i_usb_phy_of_match[] = {
 	{ .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg },
 	{ .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg },
@@ -733,6 +755,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
 	{ .compatible = "allwinner,sun7i-a20-usb-phy", .data = &sun7i_a20_cfg },
 	{ .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg },
 	{ .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg },
+	{ .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);