staging: iio:: fix some typos

typos in comments, fix ring_sw module description
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/iio/Documentation/device.txt

@@ -12,7 +12,7 @@ struct iio_dev *indio_dev = iio_device_alloc(sizeof(struct chip_state));
 where chip_state is a structure of local state data for this instance of
 the chip.
 
-That data can be accessed using iio_priv(struct iio_dev *)
+That data can be accessed using iio_priv(struct iio_dev *).
 
 Then fill in the following:
 
@@ -39,7 +39,7 @@ Then fill in the following:
 		and for associate parameters such as offsets and scales.
 	* info->write_raw:
 		Raw value writing function. Used for writable device values such
-		as DAC values and caliboffset.
+		as DAC values and calibbias.
 	* info->read_event_config:
 		Typically only set if there are some interrupt lines.  This
 		is used to read if an on sensor event detector is enabled.
@@ -62,8 +62,8 @@ Then fill in the following:
 	Poll function related elements. This controls what occurs when a trigger
 	to which this device is attached sends an event.
 - indio_dev->channels:
-	Specification of device channels. Most attributes etc are built
-	form this spec.
+	Specification of device channels. Most attributes etc. are built
+	from this spec.
 - indio_dev->num_channels:
 	How many channels are there?
 
@@ -76,4 +76,4 @@ be registered afterwards (otherwise the whole parentage of devices
 gets confused)
 
 On remove, iio_device_unregister(indio_dev) will remove the device from
-the core, and iio_device_free will clean up.
+the core, and iio_device_free(indio_dev) will clean up.

drivers/staging/iio/Documentation/overview.txt

@@ -8,7 +8,7 @@ actual devices combine some ADCs with digital to analog converters
 The aim is to fill the gap between the somewhat similar hwmon and
 input subsystems.  Hwmon is very much directed at low sample rate
 sensors used in applications such as fan speed control and temperature
-measurement.  Input is, as it's name suggests focused on input
+measurement.  Input is, as its name suggests focused on input
 devices. In some cases there is considerable overlap between these and
 IIO.
 

drivers/staging/iio/Documentation/ring.txt

@@ -15,8 +15,8 @@ struct iio_ring_buffer contains a struct iio_ring_setup_ops *setup_ops
 which in turn contains the 4 function pointers
 (preenable, postenable, predisable and postdisable).
 These are used to perform device specific steps on either side
-of the core changing it's current mode to indicate that the buffer
-is enabled or disabled (along with enabling triggering etc as appropriate).
+of the core changing its current mode to indicate that the buffer
+is enabled or disabled (along with enabling triggering etc. as appropriate).
 
 Also in struct iio_ring_buffer is a struct iio_ring_access_funcs.
 The function pointers within here are used to allow the core to handle

drivers/staging/iio/ring_sw.c

@@ -24,7 +24,7 @@
  * @read_p:		read pointer (oldest available)
  * @write_p:		write pointer
  * @half_p:		half buffer length behind write_p (event generation)
- * @update_needed:	flag to indicated change in size requested
+ * @update_needed:	flag to indicate change in size requested
  *
  * Note that the first element of all ring buffers must be a
  * struct iio_buffer.
@@ -363,5 +363,5 @@ void iio_sw_rb_free(struct iio_buffer *r)
 }
 EXPORT_SYMBOL(iio_sw_rb_free);
 
-MODULE_DESCRIPTION("Industrialio I/O software ring buffer");
+MODULE_DESCRIPTION("Industrial I/O software ring buffer");
 MODULE_LICENSE("GPL");