提交 5e877369 编写于 作者: M Maxime Ripard

ARM: sun4i: pcduino: Convert to DT label based syntax

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
上级 a86d26c8
......@@ -58,91 +58,6 @@
model = "LinkSprite pcDuino";
compatible = "linksprite,a10-pcduino", "allwinner,sun4i-a10";
soc@01c00000 {
emac: ethernet@01c0b000 {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
pinctrl@01c20800 {
led_pins_pcduino: led_pins@0 {
allwinner,pins = "PH15", "PH16";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
key_pins_pcduino: key_pins@0 {
allwinner,pins = "PH17", "PH18", "PH19";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
mdio@01c0b080 {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
mmc0: mmc@01c0f000 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci0: usb@01c14000 {
status = "okay";
};
ohci0: usb@01c14400 {
status = "okay";
};
ehci1: usb@01c1c000 {
status = "okay";
};
ohci1: usb@01c1c400 {
status = "okay";
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
i2c0: i2c@01c2ac00 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
};
leds {
compatible = "gpio-leds";
......@@ -185,12 +100,96 @@
gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
};
};
};
&ehci0 {
status = "okay";
};
reg_usb1_vbus: usb1-vbus {
status = "okay";
&ehci1 {
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
reg_usb2_vbus: usb2-vbus {
status = "okay";
&mdio {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
cd-inverted;
status = "okay";
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&pio {
led_pins_pcduino: led_pins@0 {
allwinner,pins = "PH15", "PH16";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
key_pins_pcduino: key_pins@0 {
allwinner,pins = "PH17", "PH18", "PH19";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&reg_usb1_vbus {
status = "okay";
};
&reg_usb2_vbus {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册