ARM: ux500: Enable Device Tree support mmci for Snowball

Allow proper initialisation for MMC via the mmci driver
for the Snowball low-cost development board using DT. At
the moment we continue to use DMA setup from platform code.
Once the DMA generic DT bindings have been completed we
can then port the remainder over to DT.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

arch/arm/boot/dts/snowball.dts

@@ -101,15 +101,30 @@
 			};
 		};
 
+		// External Micro SD slot
 		sdi@80126000 {
-			status = "enabled";
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+
+			#gpio-cells = <1>;
 			cd-gpios  = <&gpio6 26 0x4>; // 218
+			cd-inverted;
+
+			status = "okay";
 		};
 
+		// On-board eMMC
 		sdi@80114000 {
-			status = "enabled";
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			mmc-cap-mmc-highspeed;
 			vmmc-supply = <&ab8500_ldo_aux2_reg>;
+
+			status = "okay";
 		};
 
 		uart@80120000 {

arch/arm/mach-ux500/board-mop500-sdi.c

@@ -80,7 +80,7 @@ static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = {
 };
 #endif
 
-static struct mmci_platform_data mop500_sdi0_data = {
+struct mmci_platform_data mop500_sdi0_data = {
 	.ios_handler	= mop500_sdi0_ios_handler,
 	.ocr_mask	= MMC_VDD_29_30,
 	.f_max		= 50000000,
@@ -227,7 +227,7 @@ static struct stedma40_chan_cfg mop500_sdi4_dma_cfg_tx = {
 };
 #endif
 
-static struct mmci_platform_data mop500_sdi4_data = {
+struct mmci_platform_data mop500_sdi4_data = {
 	.ocr_mask	= MMC_VDD_29_30,
 	.f_max		= 50000000,
 	.capabilities	= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA |

arch/arm/mach-ux500/board-mop500.c

@@ -776,6 +776,8 @@ struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("arm,pl011", 0x80007000, "uart2", &uart2_plat),
 	/* Requires DMA bindings. */
 	OF_DEV_AUXDATA("arm,pl022", 0x80002000, "ssp0",  &ssp0_plat),
+	OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0",  &mop500_sdi0_data),
+	OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4",  &mop500_sdi4_data),
 	/* Requires clock name bindings. */
 	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e000, "gpio.0", NULL),
 	OF_DEV_AUXDATA("st,nomadik-gpio", 0x8012e080, "gpio.1", NULL),
@@ -851,7 +853,6 @@ static void __init u8500_init_machine(void)
 		platform_add_devices(snowball_of_platform_devs,
 				ARRAY_SIZE(snowball_of_platform_devs));
 
-		snowball_sdi_init(parent);
 	} else if (of_machine_is_compatible("st-ericsson,hrefv60+")) {
 		/*
 		 * The HREFv60 board removed a GPIO expander and routed

arch/arm/mach-ux500/board-mop500.h

@@ -9,6 +9,7 @@
 
 /* For NOMADIK_NR_GPIO */
 #include <mach/irqs.h>
+#include <linux/amba/mmci.h>
 
 /* Snowball specific GPIO assignments, this board has no GPIO expander */
 #define SNOWBALL_ACCEL_INT1_GPIO	163
@@ -78,6 +79,8 @@
 
 struct device;
 struct i2c_board_info;
+extern struct mmci_platform_data mop500_sdi0_data;
+extern struct mmci_platform_data mop500_sdi4_data;
 
 extern void mop500_sdi_init(struct device *parent);
 extern void snowball_sdi_init(struct device *parent);