Blackfin arch: add new processor ADSP-BF52x arch/mach support

Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

arch/blackfin/Kconfig

@@ -71,7 +71,7 @@ config GENERIC_CALIBRATE_DELAY
 
 config IRQCHIP_DEMUX_GPIO
 	bool
-	depends on (BF53x || BF561 || BF54x)
+	depends on (BF52x || BF53x || BF561 || BF54x)
 	default y
 
 source "init/Kconfig"
@@ -85,6 +85,21 @@ choice
 	prompt "CPU"
 	default BF533
 
+config BF522
+	bool "BF522"
+	help
+	  BF522 Processor Support.
+
+config BF525
+	bool "BF525"
+	help
+	  BF525 Processor Support.
+
+config BF527
+	bool "BF527"
+	help
+	  BF527 Processor Support.
+
 config BF531
 	bool "BF531"
 	help
@@ -144,13 +159,18 @@ endchoice
 
 choice
 	prompt "Silicon Rev"
+	default BF_REV_0_1 if BF527
 	default BF_REV_0_2 if BF537
 	default BF_REV_0_3 if BF533
 	default BF_REV_0_0 if BF549
 
 config BF_REV_0_0
 	bool "0.0"
-	depends on (BF549)
+	depends on (BF549 || BF527)
+
+config BF_REV_0_1
+	bool "0.2"
+	depends on (BF549 || BF527)
 
 config BF_REV_0_2
 	bool "0.2"
@@ -176,6 +196,11 @@ config BF_REV_NONE
 
 endchoice
 
+config BF52x
+	bool
+	depends on (BF522 || BF525 || BF527)
+	default y
+
 config BF53x
 	bool
 	depends on (BF531 || BF532 || BF533 || BF534 || BF536 || BF537)
@@ -204,6 +229,12 @@ choice
 	  configuration to ensure that all the other settings are
 	  correct.
 
+config BFIN527_EZKIT
+	bool "BF527-EZKIT"
+	depends on (BF522 || BF525 || BF527)
+	help
+	  BF533-EZKIT-LITE board Support.
+
 config BFIN533_EZKIT
 	bool "BF533-EZKIT"
 	depends on (BF533 || BF532 || BF531)
@@ -299,11 +330,17 @@ config MEM_MT48LC8M32B2B5_7
 	depends on (BFIN561_BLUETECHNIX_CM)
 	default y
 
+config MEM_MT48LC32M16A2TG_75
+	bool
+	depends on (BFIN527_EZKIT)
+	default y
+
 config BFIN_SHARED_FLASH_ENET
 	bool
 	depends on (BFIN533_STAMP)
 	default y
 
+source "arch/blackfin/mach-bf527/Kconfig"
 source "arch/blackfin/mach-bf533/Kconfig"
 source "arch/blackfin/mach-bf561/Kconfig"
 source "arch/blackfin/mach-bf537/Kconfig"
@@ -329,7 +366,7 @@ config CLKIN_HZ
 	int "Crystal Frequency in Hz"
 	default "11059200" if BFIN533_STAMP
 	default "27000000" if BFIN533_EZKIT
-	default "25000000" if BFIN537_STAMP
+	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
 	help
@@ -362,7 +399,7 @@ config VCO_MULT
 	range 1 64
 	default "22" if BFIN533_EZKIT
 	default "45" if BFIN533_STAMP
-	default "20" if BFIN537_STAMP
+	default "20" if (BFIN537_STAMP || BFIN527_EZKIT)
 	default "22" if BFIN533_BLUETECHNIX_CM
 	default "20" if BFIN537_BLUETECHNIX_CM
 	default "20" if BFIN561_BLUETECHNIX_CM
@@ -398,7 +435,7 @@ config SCLK_DIV
 	range 1 15
 	default 5 if BFIN533_EZKIT
 	default 5 if BFIN533_STAMP
-	default 4 if BFIN537_STAMP
+	default 4 if (BFIN537_STAMP || BFIN527_EZKIT)
 	default 5 if BFIN533_BLUETECHNIX_CM
 	default 4 if BFIN537_BLUETECHNIX_CM
 	default 4 if BFIN561_BLUETECHNIX_CM
@@ -450,6 +487,7 @@ comment "Memory Setup"
 config MEM_SIZE
 	int "SDRAM Memory Size in MBytes"
 	default  32 if BFIN533_EZKIT
+	default  64 if BFIN527_EZKIT
 	default  64 if BFIN537_STAMP
 	default  64 if BFIN561_EZKIT
 	default 128 if BFIN533_STAMP
@@ -459,6 +497,7 @@ config MEM_ADD_WIDTH
 	int "SDRAM Memory Address Width"
 	default  9 if BFIN533_EZKIT
 	default  9 if BFIN561_EZKIT
+	default 10 if BFIN527_EZKIT
 	default 10 if BFIN537_STAMP
 	default 11 if BFIN533_STAMP
 	default 10 if PNAV10
@@ -751,7 +790,7 @@ config LARGE_ALLOCS
 
 config BFIN_DMA_5XX
 	bool "Enable DMA Support"
-	depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561 || BF54x)
+	depends on (BF52x || BF53x || BF561 || BF54x)
 	default y
 	help
 	  DMA driver for BF5xx.

arch/blackfin/Makefile

@@ -18,6 +18,9 @@ KALLSYMS         += --symbol-prefix=_
 KBUILD_DEFCONFIG := BF537-STAMP_defconfig
 
 # setup the machine name and the machine dependent settings
+machine-$(CONFIG_BF522) := bf527
+machine-$(CONFIG_BF525) := bf527
+machine-$(CONFIG_BF527) := bf527
 machine-$(CONFIG_BF531) := bf533
 machine-$(CONFIG_BF532) := bf533
 machine-$(CONFIG_BF533) := bf533
@@ -32,6 +35,9 @@ machine-$(CONFIG_BF561) := bf561
 MACHINE := $(machine-y)
 export MACHINE
 
+cpu-$(CONFIG_BF522) := bf522
+cpu-$(CONFIG_BF525) := bf525
+cpu-$(CONFIG_BF527) := bf527
 cpu-$(CONFIG_BF531) := bf531
 cpu-$(CONFIG_BF532) := bf532
 cpu-$(CONFIG_BF533) := bf533

arch/blackfin/kernel/bfin_gpio.c

@@ -124,7 +124,7 @@ static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 };
 #endif
 
-#ifdef BF537_FAMILY
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
 static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 	(struct gpio_port_t *) PORTFIO,
 	(struct gpio_port_t *) PORTGIO,
@@ -139,6 +139,21 @@ static unsigned short *port_fer[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 
 #endif
 
+#ifdef BF527_FAMILY
+static unsigned short *port_mux[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
+	(unsigned short *) PORTF_MUX,
+	(unsigned short *) PORTG_MUX,
+	(unsigned short *) PORTH_MUX,
+};
+
+static const
+u8 pmux_offset[][16] =
+	{{ 0, 0, 0, 0, 0, 0, 0, 0, 2, 2, 4, 6, 8, 8, 10, 10 }, /* PORTF */
+	 { 0, 0, 0, 0, 0, 2, 2, 4, 4, 6, 8, 10, 10, 10, 12, 12 }, /* PORTG */
+	 { 0, 0, 0, 0, 0, 0, 0, 0, 2, 4, 4, 4, 4, 4, 4, 4 }, /* PORTH */
+	};
+#endif
+
 #ifdef BF561_FAMILY
 static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = {
 	(struct gpio_port_t *) FIO0_FLAG_D,
@@ -186,6 +201,10 @@ static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG_INTB
 static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG_INTB, IRQ_PORTG_INTB, IRQ_MAC_TX};
 #endif
 
+#ifdef BF527_FAMILY
+static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PORTF_INTB, IRQ_PORTG_INTB, IRQ_PORTH_INTB};
+#endif
+
 #ifdef BF561_FAMILY
 static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG0_INTB, IRQ_PROG1_INTB, IRQ_PROG2_INTB};
 #endif
@@ -238,7 +257,7 @@ static int cmp_label(unsigned short ident, const char *label)
 		return -EINVAL;
 }
 
-#ifdef BF537_FAMILY
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
 static void port_setup(unsigned short gpio, unsigned short usage)
 {
 	if (!check_gpio(gpio)) {
@@ -354,6 +373,18 @@ inline u16 get_portmux(unsigned short portno)
 
 	return (pmux >> (2 * gpio_sub_n(portno)) & 0x3);
 }
+#elif defined(BF527_FAMILY)
+inline void portmux_setup(unsigned short portno, unsigned short function)
+{
+	u16 pmux, ident = P_IDENT(portno);
+	u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)];
+
+	pmux = *port_mux[gpio_bank(ident)];
+	pmux &= ~(3 << offset);
+	pmux |= (function & 3) << offset;
+	*port_mux[gpio_bank(ident)] = pmux;
+	SSYNC();
+}
 #else
 # define portmux_setup(...)  do { } while (0)
 #endif

arch/blackfin/kernel/reboot.c

@@ -11,7 +11,7 @@
 #include <asm/reboot.h>
 #include <asm/system.h>
 
-#if defined(BF537_FAMILY) || defined(BF533_FAMILY)
+#if defined(BF537_FAMILY) || defined(BF533_FAMILY) || defined(BF527_FAMILY)
 #define SYSCR_VAL 	0x0
 #elif defined(BF561_FAMILY)
 #define SYSCR_VAL 	0x20

arch/blackfin/mach-bf527/Kconfig

+if (BF52x)
+
+menu "BF527 Specific Configuration"
+
+comment "Alternative Multiplexing Scheme"
+
+choice
+	prompt "SPORT0"
+	default BF527_SPORT0_PORTG
+	help
+	  Select PORT used for SPORT0. See Hardware Reference Manual
+
+config BF527_SPORT0_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF527_SPORT0_PORTG
+	bool "PORT G"
+	help
+	  PORT G
+endchoice
+
+choice
+	prompt "SPORT0 TSCLK Location"
+	depends on BF527_SPORT0_PORTG
+	default BF527_SPORT0_TSCLK_PG10
+	help
+	  Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual
+
+config BF527_SPORT0_TSCLK_PG10
+	bool "PORT PG10"
+	help
+	  PORT PG10
+
+config BF527_SPORT0_TSCLK_PG14
+	bool "PORT PG14"
+	help
+	  PORT PG14
+endchoice
+
+choice
+	prompt "UART1"
+	default BF527_UART1_PORTG
+	help
+	  Select PORT used for UART1. See Hardware Reference Manual
+
+config BF527_UART1_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF527_UART1_PORTG
+	bool "PORT G"
+	help
+	  PORT G
+endchoice
+
+choice
+	prompt "NAND (NFC) Data"
+	default BF527_NAND_D_PORTH
+	help
+	  Select PORT used for NAND Data Bus. See Hardware Reference Manual
+
+config BF527_NAND_D_PORTF
+	bool "PORT F"
+	help
+	  PORT F
+
+config BF527_NAND_D_PORTH
+	bool "PORT H"
+	help
+	  PORT H
+endchoice
+
+comment "Interrupt Priority Assignment"
+menu "Priority"
+
+config IRQ_PLL_WAKEUP
+	int "IRQ_PLL_WAKEUP"
+	default 7
+config IRQ_DMA0_ERROR
+	int "IRQ_DMA0_ERROR"
+	default 7
+config IRQ_DMAR0_BLK
+	int "IRQ_DMAR0_BLK"
+	default 7
+config IRQ_DMAR1_BLK
+	int "IRQ_DMAR1_BLK"
+	default 7
+config IRQ_DMAR0_OVR
+	int "IRQ_DMAR0_OVR"
+	default 7
+config IRQ_DMAR1_OVR
+	int "IRQ_DMAR1_OVR"
+	default 7
+config IRQ_PPI_ERROR
+	int "IRQ_PPI_ERROR"
+	default 7
+config IRQ_MAC_ERROR
+	int "IRQ_MAC_ERROR"
+	default 7
+config IRQ_SPORT0_ERROR
+	int "IRQ_SPORT0_ERROR"
+	default 7
+config IRQ_SPORT1_ERROR
+	int "IRQ_SPORT1_ERROR"
+	default 7
+config IRQ_UART0_ERROR
+	int "IRQ_UART0_ERROR"
+	default 7
+config IRQ_UART1_ERROR
+	int "IRQ_UART1_ERROR"
+	default 7
+config IRQ_RTC
+	int "IRQ_RTC"
+	default 8
+config IRQ_PPI
+	int "IRQ_PPI"
+	default 8
+config IRQ_SPORT0_RX
+	int "IRQ_SPORT0_RX"
+	default 9
+config IRQ_SPORT0_TX
+	int "IRQ_SPORT0_TX"
+	default 9
+config IRQ_SPORT1_RX
+	int "IRQ_SPORT1_RX"
+	default 9
+config IRQ_SPORT1_TX
+	int "IRQ_SPORT1_TX"
+	default 9
+config IRQ_TWI
+	int "IRQ_TWI"
+	default 10
+config IRQ_SPI
+	int "IRQ_SPI"
+	default 10
+config IRQ_UART0_RX
+	int "IRQ_UART0_RX"
+	default 10
+config IRQ_UART0_TX
+	int "IRQ_UART0_TX"
+	default 10
+config IRQ_UART1_RX
+	int "IRQ_UART1_RX"
+	default 10
+config IRQ_UART1_TX
+	int "IRQ_UART1_TX"
+	default 10
+config IRQ_OPTSEC
+	int "IRQ_OPTSEC"
+	default 11
+config IRQ_CNT
+	int "IRQ_CNT"
+	default 11
+config IRQ_MAC_RX
+	int "IRQ_MAC_RX"
+	default 11
+config IRQ_PORTH_INTA
+	int "IRQ_PORTH_INTA"
+	default 11
+config IRQ_MAC_TX
+	int "IRQ_MAC_TX/NFC"
+	default 11
+config IRQ_PORTH_INTB
+	int "IRQ_PORTH_INTB"
+	default 11
+config IRQ_TMR0
+	int "IRQ_TMR0"
+	default 12
+config IRQ_TMR1
+	int "IRQ_TMR1"
+	default 12
+config IRQ_TMR2
+	int "IRQ_TMR2"
+	default 12
+config IRQ_TMR3
+	int "IRQ_TMR3"
+	default 12
+config IRQ_TMR4
+	int "IRQ_TMR4"
+	default 12
+config IRQ_TMR5
+	int "IRQ_TMR5"
+	default 12
+config IRQ_TMR6
+	int "IRQ_TMR6"
+	default 12
+config IRQ_TMR7
+	int "IRQ_TMR7"
+	default 12
+config IRQ_PORTG_INTA
+	int "IRQ_PORTG_INTA"
+	default 12
+config IRQ_PORTG_INTB
+	int "IRQ_PORTG_INTB"
+	default 12
+config IRQ_MEM_DMA0
+	int "IRQ_MEM_DMA0"
+	default 13
+config IRQ_MEM_DMA1
+	int "IRQ_MEM_DMA1"
+	default 13
+config IRQ_WATCH
+	int "IRQ_WATCH"
+	default 13
+config IRQ_PORTF_INTA
+	int "IRQ_PORTF_INTA"
+	default 13
+config IRQ_PORTF_INTB
+	int "IRQ_PORTF_INTB"
+	default 13
+config IRQ_SPI_ERROR
+	int "IRQ_SPI_ERROR"
+	default 7
+config IRQ_NFC_ERROR
+	int "IRQ_NFC_ERROR"
+	default 7
+config IRQ_HDMA_ERROR
+	int "IRQ_HDMA_ERROR"
+	default 7
+config IRQ_HDMA
+	int "IRQ_HDMA"
+	default 7
+config IRQ_USB_EINT
+	int "IRQ_USB_EINT"
+	default 10
+config IRQ_USB_INT0
+	int "IRQ_USB_INT0"
+	default 10
+config IRQ_USB_INT1
+	int "IRQ_USB_INT1"
+	default 10
+config IRQ_USB_INT2
+	int "IRQ_USB_INT2"
+	default 10
+config IRQ_USB_DMA
+	int "IRQ_USB_DMA"
+	default 10
+
+	help
+	  Enter the priority numbers between 7-13 ONLY.  Others are Reserved.
+	  This applies to all the above.  It is not recommended to assign the
+	  highest priority number 7 to UART or any other device.
+
+endmenu
+
+endmenu
+
+endif

arch/blackfin/mach-bf527/Makefile

+#
+# arch/blackfin/mach-bf527/Makefile
+#
+
+extra-y := head.o
+
+obj-y := ints-priority.o dma.o
+
+obj-$(CONFIG_CPU_FREQ)   += cpu.o

arch/blackfin/mach-bf527/boards/Makefile

+#
+# arch/blackfin/mach-bf532/boards/Makefile
+#
+
+obj-y					+= eth_mac.o
+obj-$(CONFIG_BFIN527_EZKIT)		+= ezkit.o
+

arch/blackfin/mach-bf527/boards/eth_mac.c

+/*
+ *  arch/blackfin/mach-bf537/board/eth_mac.c
+ *
+ *  Copyright (C) 2007 Analog Devices, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+#include <linux/module.h>
+#include <asm/blackfin.h>
+
+#if	defined(CONFIG_GENERIC_BOARD) || defined(CONFIG_BFIN537_STAMP)
+
+/*
+ * Currently the MAC address is saved in Flash by U-Boot
+ */
+#define FLASH_MAC	0x203f0000
+
+void get_bf537_ether_addr(char *addr)
+{
+	unsigned int flash_mac = (unsigned int) FLASH_MAC;
+	*(u32 *)(&(addr[0])) = bfin_read32(flash_mac);
+	flash_mac += 4;
+	*(u16 *)(&(addr[4])) = bfin_read16(flash_mac);
+}
+
+#else
+
+/*
+ * Provide MAC address function for other specific board setting
+ */
+void get_bf537_ether_addr(char *addr)
+{
+	printk(KERN_WARNING "%s: No valid Ethernet MAC address found\n", __FILE__);
+}
+
+#endif
+
+EXPORT_SYMBOL(get_bf537_ether_addr);

arch/blackfin/mach-bf527/boards/ezkit.c

+/*
+ * File:         arch/blackfin/mach-bf527/boards/ezkit.c
+ * Based on:     arch/blackfin/mach-bf537/boards/stamp.c
+ * Author:       Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ *               Copyright 2005 National ICT Australia (NICTA)
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb_isp1362.h>
+#endif
+#include <linux/pata_platform.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/usb_sl811.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/reboot.h>
+#include <linux/spi/ad7877.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+char *bfin_board_name = "ADDS-BF527-EZKIT";
+
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+
+#define ISP1761_BASE       0x203C0000
+#define ISP1761_IRQ        IRQ_PF7
+
+#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+static struct resource bfin_isp1761_resources[] = {
+	[0] = {
+		.name	= "isp1761-regs",
+		.start  = ISP1761_BASE + 0x00000000,
+		.end    = ISP1761_BASE + 0x000fffff,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = ISP1761_IRQ,
+		.end    = ISP1761_IRQ,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_isp1761_device = {
+	.name           = "isp1761",
+	.id             = 0,
+	.num_resources  = ARRAY_SIZE(bfin_isp1761_resources),
+	.resource       = bfin_isp1761_resources,
+};
+
+static struct platform_device *bfin_isp1761_devices[] = {
+	&bfin_isp1761_device,
+};
+
+int __init bfin_isp1761_init(void)
+{
+	unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices);
+
+	printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+	set_irq_type(ISP1761_IRQ, IRQF_TRIGGER_FALLING);
+
+	return platform_add_devices(bfin_isp1761_devices, num_devices);
+}
+
+void __exit bfin_isp1761_exit(void)
+{
+	platform_device_unregister(&bfin_isp1761_device);
+}
+
+arch_initcall(bfin_isp1761_init);
+#endif
+
+#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+static struct resource bfin_pcmcia_cf_resources[] = {
+	{
+		.start = 0x20310000, /* IO PORT */
+		.end = 0x20312000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20311000, /* Attribute Memory */
+		.end = 0x20311FFF,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF4,
+		.end = IRQ_PF4,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+	}, {
+		.start = 6, /* Card Detect PF6 */
+		.end = 6,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pcmcia_cf_device = {
+	.name = "bfin_cf_pcmcia",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
+	.resource = bfin_pcmcia_cf_resources,
+};
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+	{
+		.name = "smc91x-regs",
+		.start = 0x20300300,
+		.end = 0x20300300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+
+		.start = IRQ_PF7,
+		.end = IRQ_PF7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+static struct resource dm9000_resources[] = {
+	[0] = {
+		.start	= 0x203FB800,
+		.end	= 0x203FB800 + 8,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= IRQ_PF9,
+		.end	= IRQ_PF9,
+		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
+	},
+};
+
+static struct platform_device dm9000_device = {
+	.name		= "dm9000",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(dm9000_resources),
+	.resource	= dm9000_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+static struct resource sl811_hcd_resources[] = {
+	{
+		.start = 0x20340000,
+		.end = 0x20340000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20340004,
+		.end = 0x20340004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = CONFIG_USB_SL811_BFIN_IRQ,
+		.end = CONFIG_USB_SL811_BFIN_IRQ,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
+void sl811_port_power(struct device *dev, int is_on)
+{
+	gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
+	gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS);
+
+	if (is_on)
+		gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 1);
+	else
+		gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 0);
+}
+#endif
+
+static struct sl811_platform_data sl811_priv = {
+	.potpg = 10,
+	.power = 250,       /* == 500mA */
+#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
+	.port_power = &sl811_port_power,
+#endif
+};
+
+static struct platform_device sl811_hcd_device = {
+	.name = "sl811-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &sl811_priv,
+	},
+	.num_resources = ARRAY_SIZE(sl811_hcd_resources),
+	.resource = sl811_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+	{
+		.start = 0x20360000,
+		.end = 0x20360000,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = 0x20360004,
+		.end = 0x20360004,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+		.end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+	.sel15Kres = 1,
+	.clknotstop = 0,
+	.oc_enable = 0,
+	.int_act_high = 0,
+	.int_edge_triggered = 0,
+	.remote_wakeup_connected = 0,
+	.no_power_switching = 1,
+	.power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+	.name = "isp1362-hcd",
+	.id = 0,
+	.dev = {
+		.platform_data = &isp1362_priv,
+	},
+	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+	.resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mac_device = {
+	.name = "bfin_mac",
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+	{
+		.start = 0x20300000,
+		.end = 0x20300000 + 0x100,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF7,
+		.end = IRQ_PF7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device net2272_bfin_device = {
+	.name = "net2272",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
+	.resource = net2272_bfin_resources,
+};
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader",
+		.size = 0x00020000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "kernel",
+		.size = 0xe0000,
+		.offset = 0x20000
+	}, {
+		.name = "file system",
+		.size = 0x700000,
+		.offset = 0x00100000,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) \
+	|| defined(CONFIG_SPI_ADC_BF533_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+	.enable_dma = 1,         /* use dma transfer with this chip*/
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+	.enable_dma = 1,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_PBX)
+static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
+	.ctl_reg	= 0x4, /* send zero */
+	.enable_dma	= 0,
+	.bits_per_word	= 8,
+	.cs_change_per_word = 1,
+};
+#endif
+
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+static struct bfin5xx_spi_chip ad5304_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 16,
+};
+
+static const struct ad7877_platform_data bfin_ad7877_ts_info = {
+	.model			= 7877,
+	.vref_delay_usecs	= 50,	/* internal, no capacitor */
+	.x_plate_ohms		= 419,
+	.y_plate_ohms		= 486,
+	.pressure_max		= 1000,
+	.pressure_min		= 0,
+	.stopacq_polarity 	= 1,
+	.first_conversion_delay = 3,
+	.acquisition_time 	= 1,
+	.averaging 		= 1,
+	.pen_down_acc_interval 	= 1,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) \
+	|| defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_SPI_ADC_BF533) \
+	|| defined(CONFIG_SPI_ADC_BF533_MODULE)
+	{
+		.modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+		.max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 1, /* Framework chip select. */
+		.platform_data = NULL, /* No spi_driver specific config */
+		.controller_data = &spi_adc_chip_info,
+	},
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) \
+	|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+	{
+		.modalias = "ad1836-spi",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+		.controller_data = &ad1836_spi_chip_info,
+	},
+#endif
+#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
+	{
+		.modalias = "ad9960-spi",
+		.max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 1,
+		.controller_data = &ad9960_spi_chip_info,
+	},
+#endif
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+	{
+		.modalias = "spi_mmc_dummy",
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 0,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "spi_mmc",
+		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SPI_MMC_CS_CHAN,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_PBX)
+	{
+		.modalias = "fxs-spi",
+		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 8 - CONFIG_J11_JUMPER,
+		.controller_data = &spi_si3xxx_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "fxo-spi",
+		.max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 8 - CONFIG_J19_JUMPER,
+		.controller_data = &spi_si3xxx_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE)
+	{
+		.modalias = "ad5304_spi",
+		.max_speed_hz = 1250000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 2,
+		.platform_data = NULL,
+		.controller_data = &ad5304_chip_info,
+		.mode = SPI_MODE_2,
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
+	{
+		.modalias		= "ad7877",
+		.platform_data		= &bfin_ad7877_ts_info,
+		.irq			= IRQ_PF6,
+		.max_speed_hz	= 12500000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num	= 1,
+		.chip_select  = 1,
+		.controller_data = &spi_ad7877_chip_info,
+	},
+#endif
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+		},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+static struct platform_device bfin_fb_device = {
+	.name = "bf537-lq035",
+};
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+static struct platform_device bfin_fb_adv7393_device = {
+	.name = "bfin-adv7393",
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	{
+		.start = 0xFFC02000,
+		.end = 0xFFC020FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+	[0] = {
+		.start = TWI0_REGBASE,
+		.end   = TWI0_REGBASE,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_TWI,
+		.end   = IRQ_TWI,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+	.name = "i2c-bfin-twi",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
+	.resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT	55
+
+static struct pata_platform_info bfin_pata_platform_data = {
+	.ioport_shift = 1,
+	.irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+	{
+		.start = 0x20314020,
+		.end = 0x2031403F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = 0x2031401C,
+		.end = 0x2031401F,
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.start = PATA_INT,
+		.end = PATA_INT,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bfin_pata_device = {
+	.name = "pata_platform",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(bfin_pata_resources),
+	.resource = bfin_pata_resources,
+	.dev = {
+		.platform_data = &bfin_pata_platform_data,
+	}
+};
+#endif
+
+static struct platform_device *stamp_devices[] __initdata = {
+#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
+	&bfin_pcmcia_cf_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
+	&sl811_hcd_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+	&isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
+	&dm9000_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+	&bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+	&net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
+	&bfin_fb_device,
+#endif
+
+#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
+	&bfin_fb_adv7393_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+	&i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	&bfin_pata_device,
+#endif
+};
+
+static int __init stamp_init(void)
+{
+	printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__);
+	platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	spi_register_board_info(bfin_spi_board_info,
+				ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+	irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+	return 0;
+}
+
+arch_initcall(stamp_init);
+
+void native_machine_restart(char *cmd)
+{
+	/* workaround reboot hang when booting from SPI */
+	if ((bfin_read_SYSCR() & 0x7) == 0x3)
+		bfin_gpio_reset_spi0_ssel1();
+}

arch/blackfin/mach-bf527/cpu.c

+/*
+ * File:         arch/blackfin/mach-bf527/cpu.c
+ * Based on:	arch/blackfin/mach-bf537/cpu.c
+ * Author:       michael.kang@analog.com
+ *
+ * Created:
+ * Description:  clock scaling for the bf527
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <asm/dpmc.h>
+#include <linux/fs.h>
+#include <asm/bfin-global.h>
+
+/* CONFIG_CLKIN_HZ=11059200 */
+#define VCO5 (CONFIG_CLKIN_HZ*45)	/*497664000 */
+#define VCO4 (CONFIG_CLKIN_HZ*36)	/*398131200 */
+#define VCO3 (CONFIG_CLKIN_HZ*27)	/*298598400 */
+#define VCO2 (CONFIG_CLKIN_HZ*18)	/*199065600 */
+#define VCO1 (CONFIG_CLKIN_HZ*9)	/*99532800 */
+#define VCO(x) VCO##x
+
+#define MFREQ(x) {VCO(x), VCO(x)/4}, {VCO(x), VCO(x)/2}, {VCO(x), VCO(x)}
+/* frequency */
+static struct cpufreq_frequency_table bf527_freq_table[] = {
+	MFREQ(1),
+	MFREQ(3),
+	{VCO4, VCO4 / 2}, {VCO4, VCO4},
+	MFREQ(5),
+	{0, CPUFREQ_TABLE_END},
+};
+
+/*
+ * dpmc_fops->ioctl()
+ * static int dpmc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg)
+ */
+static int bf527_getfreq(unsigned int cpu)
+{
+	unsigned long cclk_mhz;
+
+	/* The driver only support single cpu */
+	if (cpu == 0)
+		dpmc_fops.ioctl(NULL, NULL, IOCTL_GET_CORECLOCK, &cclk_mhz);
+	else
+		cclk_mhz = -1;
+
+	return cclk_mhz;
+}
+
+static int bf527_target(struct cpufreq_policy *policy,
+			unsigned int target_freq, unsigned int relation)
+{
+	unsigned long cclk_mhz;
+	unsigned long vco_mhz;
+	unsigned long flags;
+	unsigned int index;
+	struct cpufreq_freqs freqs;
+
+	if (cpufreq_frequency_table_target
+	    (policy, bf527_freq_table, target_freq, relation, &index))
+		return -EINVAL;
+
+	cclk_mhz = bf527_freq_table[index].frequency;
+	vco_mhz = bf527_freq_table[index].index;
+
+	dpmc_fops.ioctl(NULL, NULL, IOCTL_CHANGE_FREQUENCY, &vco_mhz);
+	freqs.old = bf527_getfreq(0);
+	freqs.new = cclk_mhz;
+	freqs.cpu = 0;
+
+	pr_debug
+	    ("cclk begin change to cclk %d,vco=%d,index=%d,target=%d,oldfreq=%d\n",
+	     cclk_mhz, vco_mhz, index, target_freq, freqs.old);
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+	local_irq_save(flags);
+	dpmc_fops.ioctl(NULL, NULL, IOCTL_SET_CCLK, &cclk_mhz);
+	local_irq_restore(flags);
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	vco_mhz = get_vco();
+	cclk_mhz = get_cclk();
+	return 0;
+}
+
+/* make sure that only the "userspace" governor is run -- anything else wouldn't make sense on
+ * this platform, anyway.
+ */
+static int bf527_verify_speed(struct cpufreq_policy *policy)
+{
+	return cpufreq_frequency_table_verify(policy, &bf527_freq_table);
+}
+
+static int __init __bf527_cpu_init(struct cpufreq_policy *policy)
+{
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	policy->governor = CPUFREQ_DEFAULT_GOVERNOR;
+
+	policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;
+	/*Now ,only support one cpu */
+	policy->cur = bf527_getfreq(0);
+	cpufreq_frequency_table_get_attr(bf527_freq_table, policy->cpu);
+	return cpufreq_frequency_table_cpuinfo(policy, bf527_freq_table);
+}
+
+static struct freq_attr *bf527_freq_attr[] = {
+	&cpufreq_freq_attr_scaling_available_freqs,
+	NULL,
+};
+
+static struct cpufreq_driver bf527_driver = {
+	.verify = bf527_verify_speed,
+	.target = bf527_target,
+	.get = bf527_getfreq,
+	.init = __bf527_cpu_init,
+	.name = "bf527",
+	.owner = THIS_MODULE,
+	.attr = bf527_freq_attr,
+};
+
+static int __init bf527_cpu_init(void)
+{
+	return cpufreq_register_driver(&bf527_driver);
+}
+
+static void __exit bf527_cpu_exit(void)
+{
+	cpufreq_unregister_driver(&bf527_driver);
+}
+
+MODULE_AUTHOR("Mickael Kang");
+MODULE_DESCRIPTION("cpufreq driver for bf527 CPU");
+MODULE_LICENSE("GPL");
+
+module_init(bf527_cpu_init);
+module_exit(bf527_cpu_exit);

arch/blackfin/mach-bf527/dma.c

+/*
+ * File:         arch/blackfin/mach-bf527/dma.c
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  This file contains the simple DMA Implementation for Blackfin
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+#include <asm/blackfin.h>
+#include <asm/dma.h>
+
+struct dma_register *base_addr[MAX_BLACKFIN_DMA_CHANNEL] = {
+	(struct dma_register *) DMA0_NEXT_DESC_PTR,
+	(struct dma_register *) DMA1_NEXT_DESC_PTR,
+	(struct dma_register *) DMA2_NEXT_DESC_PTR,
+	(struct dma_register *) DMA3_NEXT_DESC_PTR,
+	(struct dma_register *) DMA4_NEXT_DESC_PTR,
+	(struct dma_register *) DMA5_NEXT_DESC_PTR,
+	(struct dma_register *) DMA6_NEXT_DESC_PTR,
+	(struct dma_register *) DMA7_NEXT_DESC_PTR,
+	(struct dma_register *) DMA8_NEXT_DESC_PTR,
+	(struct dma_register *) DMA9_NEXT_DESC_PTR,
+	(struct dma_register *) DMA10_NEXT_DESC_PTR,
+	(struct dma_register *) DMA11_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_D0_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_S0_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_D1_NEXT_DESC_PTR,
+	(struct dma_register *) MDMA_S1_NEXT_DESC_PTR,
+};
+
+int channel2irq(unsigned int channel)
+{
+	int ret_irq = -1;
+
+	switch (channel) {
+	case CH_PPI:
+		ret_irq = IRQ_PPI;
+		break;
+
+	case CH_EMAC_RX:
+		ret_irq = IRQ_MAC_RX;
+		break;
+
+	case CH_EMAC_TX:
+		ret_irq = IRQ_MAC_TX;
+		break;
+
+	case CH_UART1_RX:
+		ret_irq = IRQ_UART1_RX;
+		break;
+
+	case CH_UART1_TX:
+		ret_irq = IRQ_UART1_TX;
+		break;
+
+	case CH_SPORT0_RX:
+		ret_irq = IRQ_SPORT0_RX;
+		break;
+
+	case CH_SPORT0_TX:
+		ret_irq = IRQ_SPORT0_TX;
+		break;
+
+	case CH_SPORT1_RX:
+		ret_irq = IRQ_SPORT1_RX;
+		break;
+
+	case CH_SPORT1_TX:
+		ret_irq = IRQ_SPORT1_TX;
+		break;
+
+	case CH_SPI:
+		ret_irq = IRQ_SPI;
+		break;
+
+	case CH_UART0_RX:
+		ret_irq = IRQ_UART0_RX;
+		break;
+
+	case CH_UART0_TX:
+		ret_irq = IRQ_UART0_TX;
+		break;
+
+	case CH_MEM_STREAM0_SRC:
+	case CH_MEM_STREAM0_DEST:
+		ret_irq = IRQ_MEM_DMA0;
+		break;
+
+	case CH_MEM_STREAM1_SRC:
+	case CH_MEM_STREAM1_DEST:
+		ret_irq = IRQ_MEM_DMA1;
+		break;
+	}
+	return ret_irq;
+}

arch/blackfin/mach-bf527/head.S

+/*
+ * File:         arch/blackfin/mach-bf527/head.S
+ * Based on:     arch/blackfin/mach-bf533/head.S
+ * Author:       Jeff Dionne <jeff@uclinux.org> COPYRIGHT 1998 D. Jeff Dionne
+ *
+ * Created:      1998
+ * Description:  Startup code for Blackfin BF537
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/linkage.h>
+#include <linux/init.h>
+#include <asm/blackfin.h>
+#include <asm/trace.h>
+
+#if CONFIG_BFIN_KERNEL_CLOCK
+#include <asm/mach-common/clocks.h>
+#include <asm/mach/mem_init.h>
+#endif
+
+.global __rambase
+.global __ramstart
+.global __ramend
+.extern ___bss_stop
+.extern ___bss_start
+.extern _bf53x_relocate_l1_mem
+
+#define INITIAL_STACK	0xFFB01000
+
+__INIT
+
+ENTRY(__start)
+	/* R0: argument of command line string, passed from uboot, save it */
+	R7 = R0;
+	/* Enable Cycle Counter and Nesting Of Interrupts */
+#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES
+	R0 = SYSCFG_SNEN;
+#else
+	R0 = SYSCFG_SNEN | SYSCFG_CCEN;
+#endif
+	SYSCFG = R0;
+	R0 = 0;
+
+	/* Clear Out All the data and pointer Registers */
+	R1 = R0;
+	R2 = R0;
+	R3 = R0;
+	R4 = R0;
+	R5 = R0;
+	R6 = R0;
+
+	P0 = R0;
+	P1 = R0;
+	P2 = R0;
+	P3 = R0;
+	P4 = R0;
+	P5 = R0;
+
+	LC0 = r0;
+	LC1 = r0;
+	L0 = r0;
+	L1 = r0;
+	L2 = r0;
+	L3 = r0;
+
+	/* Clear Out All the DAG Registers */
+	B0 = r0;
+	B1 = r0;
+	B2 = r0;
+	B3 = r0;
+
+	I0 = r0;
+	I1 = r0;
+	I2 = r0;
+	I3 = r0;
+
+	M0 = r0;
+	M1 = r0;
+	M2 = r0;
+	M3 = r0;
+
+	trace_buffer_init(p0,r0);
+	P0 = R1;
+	R0 = R1;
+
+	/* Turn off the icache */
+	p0.l = LO(IMEM_CONTROL);
+	p0.h = HI(IMEM_CONTROL);
+	R1 = [p0];
+	R0 = ~ENICPLB;
+	R0 = R0 & R1;
+
+	/* Anomaly 05000125 */
+#if ANOMALY_05000125
+	CLI R2;
+	SSYNC;
+#endif
+	[p0] = R0;
+	SSYNC;
+#if ANOMALY_05000125
+	STI R2;
+#endif
+
+	/* Turn off the dcache */
+	p0.l = LO(DMEM_CONTROL);
+	p0.h = HI(DMEM_CONTROL);
+	R1 = [p0];
+	R0 = ~ENDCPLB;
+	R0 = R0 & R1;
+
+	/* Anomaly 05000125 */
+#if ANOMALY_05000125
+	CLI R2;
+	SSYNC;
+#endif
+	[p0] = R0;
+	SSYNC;
+#if ANOMALY_05000125
+	STI R2;
+#endif
+
+
+#if defined(CONFIG_BF527)
+	p0.h = hi(EMAC_SYSTAT);
+	p0.l = lo(EMAC_SYSTAT);
+	R0.h = 0xFFFF; /* Clear EMAC Interrupt Status bits */
+	R0.l = 0xFFFF;
+	[P0] = R0;
+	SSYNC;
+#endif
+
+	/* Initialise UART - when booting from u-boot, the UART is not disabled
+	 * so if we dont initalize here, our serial console gets hosed */
+	p0.h = hi(UART1_LCR);
+	p0.l = lo(UART1_LCR);
+	r0 = 0x0(Z);
+	w[p0] = r0.L;	/* To enable DLL writes */
+	ssync;
+
+	p0.h = hi(UART1_DLL);
+	p0.l = lo(UART1_DLL);
+	r0 = 0x0(Z);
+	w[p0] = r0.L;
+	ssync;
+
+	p0.h = hi(UART1_DLH);
+	p0.l = lo(UART1_DLH);
+	r0 = 0x00(Z);
+	w[p0] = r0.L;
+	ssync;
+
+	p0.h = hi(UART1_GCTL);
+	p0.l = lo(UART1_GCTL);
+	r0 = 0x0(Z);
+	w[p0] = r0.L;	/* To enable UART clock */
+	ssync;
+
+	/* Initialize stack pointer */
+	sp.l = lo(INITIAL_STACK);
+	sp.h = hi(INITIAL_STACK);
+	fp = sp;
+	usp = sp;
+
+#ifdef CONFIG_EARLY_PRINTK
+	SP += -12;
+	call _init_early_exception_vectors;
+	SP += 12;
+#endif
+
+	/* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */
+	call _bf53x_relocate_l1_mem;
+#if CONFIG_BFIN_KERNEL_CLOCK
+	call _start_dma_code;
+#endif
+
+	/* Code for initializing Async memory banks */
+
+	p2.h = hi(EBIU_AMBCTL1);
+	p2.l = lo(EBIU_AMBCTL1);
+	r0.h = hi(AMBCTL1VAL);
+	r0.l = lo(AMBCTL1VAL);
+	[p2] = r0;
+	ssync;
+
+	p2.h = hi(EBIU_AMBCTL0);
+	p2.l = lo(EBIU_AMBCTL0);
+	r0.h = hi(AMBCTL0VAL);
+	r0.l = lo(AMBCTL0VAL);
+	[p2] = r0;
+	ssync;
+
+	p2.h = hi(EBIU_AMGCTL);
+	p2.l = lo(EBIU_AMGCTL);
+	r0 = AMGCTLVAL;
+	w[p2] = r0;
+	ssync;
+
+	/* This section keeps the processor in supervisor mode
+	 * during kernel boot.  Switches to user mode at end of boot.
+	 * See page 3-9 of Hardware Reference manual for documentation.
+	 */
+
+	/* EVT15 = _real_start */
+
+	p0.l = lo(EVT15);
+	p0.h = hi(EVT15);
+	p1.l = _real_start;
+	p1.h = _real_start;
+	[p0] = p1;
+	csync;
+
+	p0.l = lo(IMASK);
+	p0.h = hi(IMASK);
+	p1.l = IMASK_IVG15;
+	p1.h = 0x0;
+	[p0] = p1;
+	csync;
+
+	raise 15;
+	p0.l = .LWAIT_HERE;
+	p0.h = .LWAIT_HERE;
+	reti = p0;
+#if ANOMALY_05000281
+	nop; nop; nop;
+#endif
+	rti;
+
+.LWAIT_HERE:
+	jump .LWAIT_HERE;
+ENDPROC(__start)
+
+ENTRY(_real_start)
+	[ -- sp ] = reti;
+	p0.l = lo(WDOG_CTL);
+	p0.h = hi(WDOG_CTL);
+	r0 = 0xAD6(z);
+	w[p0] = r0;	/* watchdog off for now */
+	ssync;
+
+	/* Code update for BSS size == 0
+	 * Zero out the bss region.
+	 */
+
+	p1.l = ___bss_start;
+	p1.h = ___bss_start;
+	p2.l = ___bss_stop;
+	p2.h = ___bss_stop;
+	r0 = 0;
+	p2 -= p1;
+	lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2;
+.L_clear_bss:
+	B[p1++] = r0;
+
+	/* In case there is a NULL pointer reference
+	 * Zero out region before stext
+	 */
+
+	p1.l = 0x0;
+	p1.h = 0x0;
+	r0.l = __stext;
+	r0.h = __stext;
+	r0 = r0 >> 1;
+	p2 = r0;
+	r0 = 0;
+	lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2;
+.L_clear_zero:
+	W[p1++] = r0;
+
+	/* pass the uboot arguments to the global value command line */
+	R0 = R7;
+	call _cmdline_init;
+
+	p1.l = __rambase;
+	p1.h = __rambase;
+	r0.l = __sdata;
+	r0.h = __sdata;
+	[p1] = r0;
+
+	p1.l = __ramstart;
+	p1.h = __ramstart;
+	p3.l = ___bss_stop;
+	p3.h = ___bss_stop;
+
+	r1 = p3;
+	[p1] = r1;
+
+	/*
+	 * load the current thread pointer and stack
+	 */
+	r1.l = _init_thread_union;
+	r1.h = _init_thread_union;
+
+	r2.l = 0x2000;
+	r2.h = 0x0000;
+	r1 = r1 + r2;
+	sp = r1;
+	usp = sp;
+	fp = sp;
+	jump.l _start_kernel;
+ENDPROC(_real_start)
+
+__FINIT
+
+.section .l1.text
+#if CONFIG_BFIN_KERNEL_CLOCK
+ENTRY(_start_dma_code)
+
+	/* Enable PHY CLK buffer output */
+	p0.h = hi(VR_CTL);
+	p0.l = lo(VR_CTL);
+	r0.l = w[p0];
+	bitset(r0, 14);
+	w[p0] = r0.l;
+	ssync;
+
+	p0.h = hi(SIC_IWR0);
+	p0.l = lo(SIC_IWR0);
+	r0.l = 0x1;
+	r0.h = 0x0;
+	[p0] = r0;
+	SSYNC;
+
+	/*
+	 *  Set PLL_CTL
+	 *   - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+	 *   - [8]     = BYPASS    : BYPASS the PLL, run CLKIN into CCLK/SCLK
+	 *   - [7]     = output delay (add 200ps of delay to mem signals)
+	 *   - [6]     = input delay (add 200ps of input delay to mem signals)
+	 *   - [5]     = PDWN      : 1=All Clocks off
+	 *   - [3]     = STOPCK    : 1=Core Clock off
+	 *   - [1]     = PLL_OFF   : 1=Disable Power to PLL
+	 *   - [0]     = DF        : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+	 *   all other bits set to zero
+	 */
+
+	p0.h = hi(PLL_LOCKCNT);
+	p0.l = lo(PLL_LOCKCNT);
+	r0 = 0x300(Z);
+	w[p0] = r0.l;
+	ssync;
+
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITSET (R0, 24);
+	[P2] = R0;
+	SSYNC;
+
+	r0 = CONFIG_VCO_MULT & 63;       /* Load the VCO multiplier         */
+	r0 = r0 << 9;                    /* Shift it over,                  */
+	r1 = CLKIN_HALF;                 /* Do we need to divide CLKIN by 2?*/
+	r0 = r1 | r0;
+	r1 = PLL_BYPASS;                 /* Bypass the PLL?                 */
+	r1 = r1 << 8;                    /* Shift it over                   */
+	r0 = r1 | r0;                    /* add them all together           */
+
+	p0.h = hi(PLL_CTL);
+	p0.l = lo(PLL_CTL);              /* Load the address                */
+	cli r2;                          /* Disable interrupts              */
+	ssync;
+	w[p0] = r0.l;                    /* Set the value                   */
+	idle;                            /* Wait for the PLL to stablize    */
+	sti r2;                          /* Enable interrupts               */
+
+.Lcheck_again:
+	p0.h = hi(PLL_STAT);
+	p0.l = lo(PLL_STAT);
+	R0 = W[P0](Z);
+	CC = BITTST(R0,5);
+	if ! CC jump .Lcheck_again;
+
+	/* Configure SCLK & CCLK Dividers */
+	r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+	p0.h = hi(PLL_DIV);
+	p0.l = lo(PLL_DIV);
+	w[p0] = r0.l;
+	ssync;
+
+	p0.l = lo(EBIU_SDRRC);
+	p0.h = hi(EBIU_SDRRC);
+	r0 = mem_SDRRC;
+	w[p0] = r0.l;
+	ssync;
+
+	p0.l = LO(EBIU_SDBCTL);
+	p0.h = HI(EBIU_SDBCTL);     /* SDRAM Memory Bank Control Register */
+	r0 = mem_SDBCTL;
+	w[p0] = r0.l;
+	ssync;
+
+	P2.H = hi(EBIU_SDGCTL);
+	P2.L = lo(EBIU_SDGCTL);
+	R0 = [P2];
+	BITCLR (R0, 24);
+	p0.h = hi(EBIU_SDSTAT);
+	p0.l = lo(EBIU_SDSTAT);
+	r2.l = w[p0];
+	cc = bittst(r2,3);
+	if !cc jump .Lskip;
+	NOP;
+	BITSET (R0, 23);
+.Lskip:
+	[P2] = R0;
+	SSYNC;
+
+	R0.L = lo(mem_SDGCTL);
+	R0.H = hi(mem_SDGCTL);
+	R1 = [p2];
+	R1 = R1 | R0;
+	[P2] = R1;
+	SSYNC;
+
+	p0.h = hi(SIC_IWR0);
+	p0.l = lo(SIC_IWR0);
+	r0.l = lo(IWR_ENABLE_ALL);
+	r0.h = hi(IWR_ENABLE_ALL);
+	[p0] = r0;
+	SSYNC;
+
+	RTS;
+ENDPROC(_start_dma_code)
+#endif /* CONFIG_BFIN_KERNEL_CLOCK */
+
+.data
+
+/*
+ * Set up the usable of RAM stuff. Size of RAM is determined then
+ * an initial stack set up at the end.
+ */
+
+.align 4
+__rambase:
+.long   0
+__ramstart:
+.long   0
+__ramend:
+.long   0

arch/blackfin/mach-bf527/ints-priority.c

+/*
+ * File:         arch/blackfin/mach-bf537/ints-priority.c
+ * Based on:     arch/blackfin/mach-bf533/ints-priority.c
+ * Author:       Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * Created:
+ * Description:  Set up the interrupt priorities
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/module.h>
+#include <linux/irq.h>
+#include <asm/blackfin.h>
+
+void program_IAR(void)
+{
+	/* Program the IAR0 Register with the configured priority */
+	bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) |
+			((CONFIG_IRQ_DMA0_ERROR - 7) << IRQ_DMA0_ERROR_POS) |
+			((CONFIG_IRQ_DMAR0_BLK - 7) << IRQ_DMAR0_BLK_POS) |
+			((CONFIG_IRQ_DMAR1_BLK - 7) << IRQ_DMAR1_BLK_POS) |
+			((CONFIG_IRQ_DMAR0_OVR - 7) << IRQ_DMAR0_OVR_POS) |
+			((CONFIG_IRQ_DMAR1_OVR - 7) << IRQ_DMAR1_OVR_POS) |
+			((CONFIG_IRQ_PPI_ERROR - 7) << IRQ_PPI_ERROR_POS) |
+			((CONFIG_IRQ_MAC_ERROR - 7) << IRQ_MAC_ERROR_POS));
+
+
+	bfin_write_SIC_IAR1(((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) |
+			((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS) |
+			((CONFIG_IRQ_UART0_ERROR - 7) << IRQ_UART0_ERROR_POS) |
+			((CONFIG_IRQ_UART1_ERROR - 7) << IRQ_UART1_ERROR_POS) |
+			((CONFIG_IRQ_RTC - 7) << IRQ_RTC_POS) |
+			((CONFIG_IRQ_PPI - 7) << IRQ_PPI_POS));
+
+	bfin_write_SIC_IAR2(((CONFIG_IRQ_SPORT0_RX - 7) << IRQ_SPORT0_RX_POS) |
+			((CONFIG_IRQ_SPORT0_TX - 7) << IRQ_SPORT0_TX_POS) |
+			((CONFIG_IRQ_SPORT1_RX - 7) << IRQ_SPORT1_RX_POS) |
+			((CONFIG_IRQ_SPORT1_TX - 7) << IRQ_SPORT1_TX_POS) |
+			((CONFIG_IRQ_TWI - 7) << IRQ_TWI_POS) |
+			((CONFIG_IRQ_SPI - 7) << IRQ_SPI_POS) |
+			((CONFIG_IRQ_UART0_RX - 7) << IRQ_UART0_RX_POS) |
+			((CONFIG_IRQ_UART0_TX - 7) << IRQ_UART0_TX_POS));
+
+	bfin_write_SIC_IAR3(((CONFIG_IRQ_UART1_RX - 7) << IRQ_UART1_RX_POS) |
+			((CONFIG_IRQ_UART1_TX - 7) << IRQ_UART1_TX_POS) |
+			((CONFIG_IRQ_OPTSEC - 7) << IRQ_OPTSEC_POS) |
+			((CONFIG_IRQ_CNT - 7) << IRQ_CNT_POS) |
+			((CONFIG_IRQ_MAC_RX - 7) << IRQ_MAC_RX_POS) |
+			((CONFIG_IRQ_PORTH_INTA - 7) << IRQ_PORTH_INTA_POS) |
+			((CONFIG_IRQ_MAC_TX - 7) << IRQ_MAC_TX_POS) |
+			((CONFIG_IRQ_PORTH_INTB - 7) << IRQ_PORTH_INTB_POS));
+
+	bfin_write_SIC_IAR4(((CONFIG_IRQ_TMR0 - 7) << IRQ_TMR0_POS) |
+			((CONFIG_IRQ_TMR1 - 7) << IRQ_TMR1_POS) |
+			((CONFIG_IRQ_TMR2 - 7) << IRQ_TMR2_POS) |
+			((CONFIG_IRQ_TMR3 - 7) << IRQ_TMR3_POS) |
+			((CONFIG_IRQ_TMR4 - 7) << IRQ_TMR4_POS) |
+			((CONFIG_IRQ_TMR5 - 7) << IRQ_TMR5_POS) |
+			((CONFIG_IRQ_TMR6 - 7) << IRQ_TMR6_POS) |
+			((CONFIG_IRQ_TMR7 - 7) << IRQ_TMR7_POS));
+
+	bfin_write_SIC_IAR5(((CONFIG_IRQ_PORTG_INTA - 7) << IRQ_PORTG_INTA_POS) |
+			((CONFIG_IRQ_PORTG_INTB - 7) << IRQ_PORTG_INTB_POS) |
+			((CONFIG_IRQ_MEM_DMA0 - 7) << IRQ_MEM_DMA0_POS) |
+			((CONFIG_IRQ_MEM_DMA1 - 7) << IRQ_MEM_DMA1_POS) |
+			((CONFIG_IRQ_WATCH - 7) << IRQ_WATCH_POS) |
+			((CONFIG_IRQ_PORTF_INTA - 7) << IRQ_PORTF_INTA_POS) |
+			((CONFIG_IRQ_PORTF_INTB - 7) << IRQ_PORTF_INTB_POS) |
+			((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS));
+
+	bfin_write_SIC_IAR6(((CONFIG_IRQ_NFC_ERROR - 7) << IRQ_NFC_ERROR_POS) |
+			((CONFIG_IRQ_HDMA_ERROR - 7) << IRQ_HDMA_ERROR_POS) |
+			((CONFIG_IRQ_HDMA - 7) << IRQ_HDMA_POS) |
+			((CONFIG_IRQ_USB_EINT - 7) << IRQ_USB_EINT_POS) |
+			((CONFIG_IRQ_USB_INT0 - 7) << IRQ_USB_INT0_POS) |
+			((CONFIG_IRQ_USB_INT1 - 7) << IRQ_USB_INT1_POS) |
+			((CONFIG_IRQ_USB_INT2 - 7) << IRQ_USB_INT2_POS) |
+			((CONFIG_IRQ_USB_DMA - 7) << IRQ_USB_DMA_POS));
+
+	SSYNC();
+}

arch/blackfin/mach-common/ints-priority-sc.c

@@ -92,10 +92,15 @@ static void __init search_IAR(void)
 
 		for (irqn = 0; irqn < NR_PERI_INTS; irqn++) {
 			int iar_shift = (irqn & 7) * 4;
-			if (ivg ==
+				if (ivg ==
 			    (0xf &
+#ifndef CONFIG_BF52x
 			     bfin_read32((unsigned long *)SIC_IAR0 +
 					 (irqn >> 3)) >> iar_shift)) {
+#else
+			     bfin_read32((unsigned long *)SIC_IAR0 +
+					 ((irqn%32) >> 3) + ((irqn / 32) * 16)) >> iar_shift)) {
+#endif
 				ivg_table[irq_pos].irqno = IVG7 + irqn;
 				ivg_table[irq_pos].isrflag = 1 << (irqn % 32);
 				ivg7_13[ivg].istop++;
@@ -140,7 +145,7 @@ static void bfin_core_unmask_irq(unsigned int irq)
 
 static void bfin_internal_mask_irq(unsigned int irq)
 {
-#ifndef CONFIG_BF54x
+#ifdef CONFIG_BF53x
 	bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() &
 			     ~(1 << (irq - (IRQ_CORETMR + 1))));
 #else
@@ -155,7 +160,7 @@ static void bfin_internal_mask_irq(unsigned int irq)
 
 static void bfin_internal_unmask_irq(unsigned int irq)
 {
-#ifndef CONFIG_BF54x
+#ifdef CONFIG_BF53x
 	bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() |
 			     (1 << (irq - (IRQ_CORETMR + 1))));
 #else
@@ -750,13 +755,15 @@ int __init init_arch_irq(void)
 	int irq;
 	unsigned long ilat = 0;
 	/*  Disable all the peripheral intrs  - page 4-29 HW Ref manual */
-#ifdef CONFIG_BF54x
+#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x)
 	bfin_write_SIC_IMASK0(SIC_UNMASK_ALL);
 	bfin_write_SIC_IMASK1(SIC_UNMASK_ALL);
-	bfin_write_SIC_IMASK2(SIC_UNMASK_ALL);
 	bfin_write_SIC_IWR0(IWR_ENABLE_ALL);
 	bfin_write_SIC_IWR1(IWR_ENABLE_ALL);
+#ifdef CONFIG_BF54x
+	bfin_write_SIC_IMASK2(SIC_UNMASK_ALL);
 	bfin_write_SIC_IWR2(IWR_ENABLE_ALL);
+#endif
 #else
 	bfin_write_SIC_IMASK(SIC_UNMASK_ALL);
 	bfin_write_SIC_IWR(IWR_ENABLE_ALL);
@@ -787,7 +794,7 @@ int __init init_arch_irq(void)
 
 			switch (irq) {
 #ifdef CONFIG_IRQCHIP_DEMUX_GPIO
-#ifndef CONFIG_BF54x
+#if defined(CONFIG_BF53x)
 			case IRQ_PROG_INTA:
 				set_irq_chained_handler(irq,
 							bfin_demux_gpio_irq);
@@ -798,7 +805,7 @@ int __init init_arch_irq(void)
 							bfin_demux_gpio_irq);
 				break;
 #endif
-#else
+#elif defined(CONFIG_BF54x)
 			case IRQ_PINT0:
 				set_irq_chained_handler(irq,
 							bfin_demux_gpio_irq);
@@ -815,7 +822,20 @@ int __init init_arch_irq(void)
 				set_irq_chained_handler(irq,
 							bfin_demux_gpio_irq);
 				break;
-#endif				/*CONFIG_BF54x */
+#elif defined(CONFIG_BF52x)
+			case IRQ_PORTF_INTA:
+				set_irq_chained_handler(irq,
+							bfin_demux_gpio_irq);
+				break;
+			case IRQ_PORTG_INTA:
+				set_irq_chained_handler(irq,
+							bfin_demux_gpio_irq);
+				break;
+			case IRQ_PORTH_INTA:
+				set_irq_chained_handler(irq,
+							bfin_demux_gpio_irq);
+				break;
+#endif
 #endif
 			default:
 				set_irq_handler(irq, handle_simple_irq);
@@ -880,14 +900,15 @@ void do_irq(int vec, struct pt_regs *fp)
 	} else {
 		struct ivgx *ivg = ivg7_13[vec - IVG7].ifirst;
 		struct ivgx *ivg_stop = ivg7_13[vec - IVG7].istop;
-#ifdef CONFIG_BF54x
+#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x)
 		unsigned long sic_status[3];
 
 		SSYNC();
 		sic_status[0] = bfin_read_SIC_ISR(0) & bfin_read_SIC_IMASK(0);
 		sic_status[1] = bfin_read_SIC_ISR(1) & bfin_read_SIC_IMASK(1);
+#ifdef CONFIG_BF54x
 		sic_status[2] = bfin_read_SIC_ISR(2) & bfin_read_SIC_IMASK(2);
-
+#endif
 		for (;; ivg++) {
 			if (ivg >= ivg_stop) {
 				atomic_inc(&num_spurious);

include/asm-blackfin/bf5xx_timers.h

@@ -16,7 +16,7 @@
 /*
  * BF537: 8 timers:
  */
-#if defined(CONFIG_BF537)
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
 #  define MAX_BLACKFIN_GPTIMERS 8
 #  define TIMER0_GROUP_REG     TIMER_ENABLE
 #endif

include/asm-blackfin/gpio.h

@@ -29,6 +29,7 @@
 
 /*
 *  Number     BF537/6/4    BF561    BF533/2/1
+*             BF527/5/2
 *
 *  GPIO_0       PF0         PF0        PF0
 *  GPIO_1       PF1         PF1        PF1
@@ -164,7 +165,7 @@
 
 #endif
 
-#ifdef BF537_FAMILY
+#if defined(BF527_FAMILY) || defined(BF537_FAMILY)
 #define MAX_BLACKFIN_GPIOS 48
 
 #define	GPIO_PF0	0

include/asm-blackfin/mach-bf527/anomaly.h

@@ -38,4 +38,12 @@
 
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000323 (0)
+#define ANOMALY_05000244 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000158 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000263 (0)
+#define ANOMALY_05000311 (0)
+#define ANOMALY_05000230 (0)
 #endif

include/asm-blackfin/mach-bf527/bf527.h

+/*
+ * File:         include/asm-blackfin/mach-bf527/bf527.h
+ * Based on:	include/asm-blackfin/mach-bf537/bf537.h
+ * Author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * Created:
+ * Description:  SYSTEM MMR REGISTER AND MEMORY MAP FOR ADSP-BF527
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#ifndef __MACH_BF527_H__
+#define __MACH_BF527_H__
+
+#define SUPPORTED_REVID 2
+
+#define OFFSET_(x) ((x) & 0x0000FFFF)
+
+/*some misc defines*/
+#define IMASK_IVG15		0x8000
+#define IMASK_IVG14		0x4000
+#define IMASK_IVG13		0x2000
+#define IMASK_IVG12		0x1000
+
+#define IMASK_IVG11		0x0800
+#define IMASK_IVG10		0x0400
+#define IMASK_IVG9		0x0200
+#define IMASK_IVG8		0x0100
+
+#define IMASK_IVG7		0x0080
+#define IMASK_IVGTMR	0x0040
+#define IMASK_IVGHW		0x0020
+
+/***************************/
+
+#define BFIN_DSUBBANKS	4
+#define BFIN_DWAYS		2
+#define BFIN_DLINES		64
+#define BFIN_ISUBBANKS	4
+#define BFIN_IWAYS		4
+#define BFIN_ILINES		32
+
+#define WAY0_L			0x1
+#define WAY1_L			0x2
+#define WAY01_L			0x3
+#define WAY2_L			0x4
+#define WAY02_L			0x5
+#define	WAY12_L			0x6
+#define	WAY012_L		0x7
+
+#define	WAY3_L			0x8
+#define	WAY03_L			0x9
+#define	WAY13_L			0xA
+#define	WAY013_L		0xB
+
+#define	WAY32_L			0xC
+#define	WAY320_L		0xD
+#define	WAY321_L		0xE
+#define	WAYALL_L		0xF
+
+#define DMC_ENABLE (2<<2)	/*yes, 2, not 1 */
+
+/********************************* EBIU Settings ************************************/
+#define AMBCTL0VAL	((CONFIG_BANK_1 << 16) | CONFIG_BANK_0)
+#define AMBCTL1VAL	((CONFIG_BANK_3 << 16) | CONFIG_BANK_2)
+
+#ifdef CONFIG_C_AMBEN_ALL
+#define V_AMBEN AMBEN_ALL
+#endif
+#ifdef CONFIG_C_AMBEN
+#define V_AMBEN 0x0
+#endif
+#ifdef CONFIG_C_AMBEN_B0
+#define V_AMBEN AMBEN_B0
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1
+#define V_AMBEN AMBEN_B0_B1
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1_B2
+#define V_AMBEN AMBEN_B0_B1_B2
+#endif
+#ifdef CONFIG_C_AMCKEN
+#define V_AMCKEN AMCKEN
+#else
+#define V_AMCKEN 0x0
+#endif
+#ifdef CONFIG_C_CDPRIO
+#define V_CDPRIO 0x100
+#else
+#define V_CDPRIO 0x0
+#endif
+
+#define AMGCTLVAL	(V_AMBEN | V_AMCKEN | V_CDPRIO)
+
+#ifdef CONFIG_BF527
+#define CPU "BF527"
+#endif
+#ifdef CONFIG_BF525
+#define CPU "BF525"
+#endif
+#ifdef CONFIG_BF522
+#define CPU "BF522"
+#endif
+#ifndef CPU
+#define	CPU "UNKNOWN"
+#define CPUID 0x0
+#endif
+
+#endif				/* __MACH_BF527_H__  */

include/asm-blackfin/mach-bf527/bfin_serial_5xx.h

+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define NR_PORTS		2
+
+#define OFFSET_THR              0x00	/* Transmit Holding register            */
+#define OFFSET_RBR              0x00	/* Receive Buffer register              */
+#define OFFSET_DLL              0x00	/* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04	/* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04	/* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08	/* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C	/* Line Control Register                */
+#define OFFSET_MCR              0x10	/* Modem Control Register               */
+#define OFFSET_LSR              0x14	/* Line Status Register                 */
+#define OFFSET_MSR              0x18	/* Modem Status Register                */
+#define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24	/* Global Control Register              */
+
+#define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
+#define UART_GET_DLL(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLL))
+#define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
+#define UART_GET_DLH(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLH))
+#define UART_GET_IIR(uart)      bfin_read16(((uart)->port.membase + OFFSET_IIR))
+#define UART_GET_LCR(uart)      bfin_read16(((uart)->port.membase + OFFSET_LCR))
+#define UART_GET_LSR(uart)      bfin_read16(((uart)->port.membase + OFFSET_LSR))
+#define UART_GET_GCTL(uart)     bfin_read16(((uart)->port.membase + OFFSET_GCTL))
+
+#define UART_PUT_CHAR(uart, v)   bfin_write16(((uart)->port.membase + OFFSET_THR), v)
+#define UART_PUT_DLL(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_DLL), v)
+#define UART_PUT_IER(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_IER), v)
+#define UART_PUT_DLH(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_DLH), v)
+#define UART_PUT_LCR(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_LCR), v)
+#define UART_PUT_GCTL(uart, v)   bfin_write16(((uart)->port.membase + OFFSET_GCTL), v)
+
+#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS)
+# define CONFIG_SERIAL_BFIN_CTSRTS
+
+# ifndef CONFIG_UART0_CTS_PIN
+#  define CONFIG_UART0_CTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART0_RTS_PIN
+#  define CONFIG_UART0_RTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART1_CTS_PIN
+#  define CONFIG_UART1_CTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART1_RTS_PIN
+#  define CONFIG_UART1_RTS_PIN -1
+# endif
+#endif
+/*
+ * The pin configuration is different from schematic
+ */
+struct bfin_serial_port {
+	struct uart_port port;
+	unsigned int old_status;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	int tx_done;
+	int tx_count;
+	struct circ_buf rx_dma_buf;
+	struct timer_list rx_dma_timer;
+	int rx_dma_nrows;
+	unsigned int tx_dma_channel;
+	unsigned int rx_dma_channel;
+	struct work_struct tx_dma_workqueue;
+#else
+	struct work_struct cts_workqueue;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	int cts_pin;
+	int rts_pin;
+#endif
+};
+
+struct bfin_serial_port bfin_serial_ports[NR_PORTS];
+struct bfin_serial_res {
+	unsigned long uart_base_addr;
+	int uart_irq;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	unsigned int uart_tx_dma_channel;
+	unsigned int uart_rx_dma_channel;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	int uart_cts_pin;
+	int uart_rts_pin;
+#endif
+};
+
+struct bfin_serial_res bfin_serial_resource[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	{
+	 0xFFC00400,
+	 IRQ_UART0_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	 CH_UART0_TX,
+	 CH_UART0_RX,
+#endif
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+	 CONFIG_UART0_CTS_PIN,
+	 CONFIG_UART0_RTS_PIN,
+#endif
+	 },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	{
+	 0xFFC02000,
+	 IRQ_UART1_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	 CH_UART1_TX,
+	 CH_UART1_RX,
+#endif
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	 CONFIG_UART1_CTS_PIN,
+	 CONFIG_UART1_RTS_PIN,
+#endif
+	 },
+#endif
+};
+
+int nr_ports = ARRAY_SIZE(bfin_serial_resource);
+
+#define DRIVER_NAME "bfin-uart"
+
+static void bfin_serial_hw_init(struct bfin_serial_port *uart)
+{
+
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	peripheral_request(P_UART0_TX, DRIVER_NAME);
+	peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	peripheral_request(P_UART1_TX, DRIVER_NAME);
+	peripheral_request(P_UART1_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	if (uart->cts_pin >= 0) {
+		gpio_request(uart->cts_pin, DRIVER_NAME);
+		gpio_direction_input(uart->cts_pin);
+	}
+
+	if (uart->rts_pin >= 0) {
+		gpio_request(uart->rts_pin, DRIVER_NAME);
+		gpio_direction_output(uart->rts_pin);
+	}
+#endif
+}

include/asm-blackfin/mach-bf527/blackfin.h

+/*
+ * File:         include/asm-blackfin/mach-bf527/blackfin.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _MACH_BLACKFIN_H_
+#define _MACH_BLACKFIN_H_
+
+#define BF527_FAMILY
+
+#include "bf527.h"
+#include "mem_map.h"
+#include "defBF522.h"
+#include "anomaly.h"
+
+#if defined(CONFIG_BF527)
+#include "defBF527.h"
+#endif
+
+#if defined(CONFIG_BF525)
+#include "defBF525.h"
+#endif
+
+#if !defined(__ASSEMBLY__)
+#include "cdefBF522.h"
+
+#if defined(CONFIG_BF527)
+#include "cdefBF527.h"
+#endif
+
+#if defined(CONFIG_BF525)
+#include "cdefBF525.h"
+#endif
+#endif
+
+/* UART_IIR Register */
+#define STATUS(x)	((x << 1) & 0x06)
+#define STATUS_P1	0x02
+#define STATUS_P0	0x01
+
+/* DPMC*/
+#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
+#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
+#define STOPCK_OFF STOPCK
+
+/* PLL_DIV Masks													*/
+#define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
+#define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
+#define CCLK_DIV4 CSEL_DIV4	/*          CCLK = VCO / 4                                  */
+#define CCLK_DIV8 CSEL_DIV8	/*          CCLK = VCO / 8                                  */
+
+#endif

include/asm-blackfin/mach-bf527/cdefBF52x_base.h

@@ -45,8 +45,8 @@
 #define bfin_write_PLL_STAT(val)		bfin_write16(PLL_STAT, val)
 #define bfin_read_PLL_LOCKCNT()			bfin_read16(PLL_LOCKCNT)
 #define bfin_write_PLL_LOCKCNT(val)		bfin_write16(PLL_LOCKCNT, val)
-#define bfin_read_CHIPID()			bfin_read16(CHIPID)
-#define bfin_write_CHIPID(val)			bfin_write16(CHIPID, val)
+#define bfin_read_CHIPID()			bfin_read32(CHIPID)
+#define bfin_write_CHIPID(val)			bfin_write32(CHIPID, val)
 
 
 /* System Interrupt Controller (0xFFC00100 - 0xFFC001FF)							*/
@@ -59,9 +59,8 @@
 #define bfin_write_SIC_RVECT(val)		bfin_write32(SIC_RVECT, val)
 #define bfin_read_SIC_IMASK0()			bfin_read32(SIC_IMASK0)
 #define bfin_write_SIC_IMASK0(val)		bfin_write32(SIC_IMASK0, val)
-/* legacy register name (below) provided for backwards code compatibility */
-#define bfin_read_SIC_IMASK()			bfin_read32(SIC_IMASK)
-#define bfin_write_SIC_IMASK(val)		bfin_write32(SIC_IMASK, val)
+#define bfin_read_SIC_IMASK(x)			bfin_read32(SIC_IMASK0 + (x << 6))
+#define bfin_write_SIC_IMASK(x, val)		bfin_write32((SIC_IMASK0 + (x << 6)), val)
 
 #define bfin_read_SIC_IAR0()			bfin_read32(SIC_IAR0)
 #define bfin_write_SIC_IAR0(val)		bfin_write32(SIC_IAR0, val)
@@ -74,15 +73,13 @@
 
 #define bfin_read_SIC_ISR0()			bfin_read32(SIC_ISR0)
 #define bfin_write_SIC_ISR0(val)		bfin_write32(SIC_ISR0, val)
-/* legacy register name (below) provided for backwards code compatibility */
-#define bfin_read_SIC_ISR()			bfin_read32(SIC_ISR)
-#define bfin_write_SIC_ISR(val)			bfin_write32(SIC_ISR, val)
+#define bfin_read_SIC_ISR(x)			bfin_read32(SIC_ISR0 + (x << 6))
+#define bfin_write_SIC_ISR(x, val)		bfin_write32((SIC_ISR0 + (x << 6)), val)
 
 #define bfin_read_SIC_IWR0()			bfin_read32(SIC_IWR0)
 #define bfin_write_SIC_IWR0(val)		bfin_write32(SIC_IWR0, val)
-/* legacy register name (below) provided for backwards code compatibility */
-#define bfin_read_SIC_IWR()			bfin_read32(SIC_IWR)
-#define bfin_write_SIC_IWR(val)			bfin_write32(SIC_IWR, val)
+#define bfin_read_SIC_IWR(x)			bfin_read32(SIC_IWR0 + (x << 6))
+#define bfin_write_SIC_IWR(x, val)		bfin_write32((SIC_IWR0 + (x << 6)), val)
 
 /* SIC Additions to ADSP-BF52x (0xFFC0014C - 0xFFC00162) */
 

include/asm-blackfin/mach-bf527/defBF527.h

@@ -32,12 +32,12 @@
 #define _DEF_BF527_H
 
 /* Include all Core registers and bit definitions */
-#include <def_LPBlackfin.h>
+#include <asm/mach-common/def_LPBlackfin.h>
 
 /* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF527 */
 
 /* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
-#include <defBF52x_base.h>
+#include "defBF52x_base.h"
 
 /* The following are the #defines needed by ADSP-BF527 that are not in the common header */
 /* 10/100 Ethernet Controller	(0xFFC03000 - 0xFFC031FF) */

include/asm-blackfin/mach-bf527/defBF52x_base.h

@@ -52,13 +52,13 @@
 #define SYSCR				0xFFC00104	/* System Configuration Register			*/
 #define SIC_RVECT			0xFFC00108	/* Interrupt Reset Vector Address Register	*/
 
-#define SIC_IMASK			0xFFC0010C	/* Interrupt Mask Register					*/
+#define SIC_IMASK0			0xFFC0010C	/* Interrupt Mask Register					*/
 #define SIC_IAR0			0xFFC00110	/* Interrupt Assignment Register 0			*/
 #define SIC_IAR1			0xFFC00114	/* Interrupt Assignment Register 1			*/
 #define SIC_IAR2			0xFFC00118	/* Interrupt Assignment Register 2			*/
 #define SIC_IAR3			0xFFC0011C	/* Interrupt Assignment Register 3			*/
-#define SIC_ISR				0xFFC00120	/* Interrupt Status Register				*/
-#define SIC_IWR				0xFFC00124	/* Interrupt Wakeup Register				*/
+#define SIC_ISR0				0xFFC00120	/* Interrupt Status Register				*/
+#define SIC_IWR0				0xFFC00124	/* Interrupt Wakeup Register				*/
 
 /* SIC Additions to ADSP-BF52x (0xFFC0014C - 0xFFC00162) */
 #define SIC_IMASK1                      0xFFC0014C     /* Interrupt Mask register of SIC2 */
@@ -691,6 +691,8 @@
 
 /* *************  SYSTEM INTERRUPT CONTROLLER MASKS *************************************/
 /* Peripheral Masks For SIC_ISR, SIC_IWR, SIC_IMASK										*/
+
+#if 0
 #define IRQ_PLL_WAKEUP	0x00000001	/* PLL Wakeup Interrupt			 					*/
 
 #define IRQ_ERROR1      0x00000002  /* Error Interrupt (DMA, DMARx Block, DMARx Overflow) */
@@ -732,6 +734,7 @@
 #define IRQ_DMA15		0x40000000	/* DMA Channels 15 (MDMA0 Destination) TX Interrupt */
 #define IRQ_WDOG		0x80000000	/* Software Watchdog Timer Interrupt 				*/
 #define IRQ_PFB_PORTG	0x10000000	/* PF Port G (PF31:16) Interrupt B 					*/
+#endif
 
 /* SIC_IAR0 Macros															*/
 #define P0_IVG(x)		(((x)&0xF)-7)			/* Peripheral #0 assigned IVG #x 	*/

include/asm-blackfin/mach-bf527/dma.h

+/*
+ * file:        include/asm-blackfin/mach-bf527/dma.h
+ * based on:	include/asm-blackfin/mach-bf537/dma.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	system DMA map
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _MACH_DMA_H_
+#define _MACH_DMA_H_
+
+#define MAX_BLACKFIN_DMA_CHANNEL 16
+
+#define CH_PPI 			0	/* PPI receive/transmit or NFC */
+#define CH_NFC			0	/* PPI receive/transmit or NFC */
+#define CH_EMAC_RX 		1	/* Ethernet MAC receive or HOSTDP */
+#define CH_EMAC_HOSTDP 		1	/* Ethernet MAC receive or HOSTDP */
+#define CH_EMAC_TX 		2	/* Ethernet MAC transmit or NFC */
+#define CH_SPORT0_RX 		3	/* SPORT0 receive */
+#define CH_SPORT0_TX 		4	/* SPORT0 transmit */
+#define CH_SPORT1_RX 		5	/* SPORT1 receive */
+#define CH_SPORT1_TX 		6	/* SPORT1 transmit */
+#define CH_SPI 			7	/* SPI transmit/receive */
+#define CH_UART0_RX 		8	/* UART0 receive */
+#define CH_UART0_TX 		9	/* UART0 transmit */
+#define CH_UART1_RX 		10	/* UART1 receive */
+#define CH_UART1_TX 		11	/* UART1 transmit */
+
+#define CH_MEM_STREAM0_DEST	12	/* TX */
+#define CH_MEM_STREAM0_SRC  	13	/* RX */
+#define CH_MEM_STREAM1_DEST	14	/* TX */
+#define CH_MEM_STREAM1_SRC 	15	/* RX */
+
+extern int channel2irq(unsigned int channel);
+extern struct dma_register *base_addr[];
+
+#endif

include/asm-blackfin/mach-bf527/irq.h

+/*
+ * file:	include/asm-blackfin/mach-bf527/irq.h
+ * based on:	include/asm-blackfin/mach-bf537/irq.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	system mmr register map
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _BF527_IRQ_H_
+#define _BF527_IRQ_H_
+
+/*
+ * Interrupt source definitions
+	Event Source    Core Event Name
+	Core        Emulation               **
+	Events         (highest priority)  EMU         0
+	Reset                   RST         1
+	NMI                     NMI         2
+	Exception               EVX         3
+	Reserved                --          4
+	Hardware Error          IVHW        5
+	Core Timer              IVTMR       6 *
+
+	.....
+
+	 Software Interrupt 1    IVG14       31
+	 Software Interrupt 2    --
+	 (lowest priority)  IVG15       32 *
+*/
+
+#define NR_PERI_INTS    (2 * 32)
+
+/* The ABSTRACT IRQ definitions */
+/** the first seven of the following are fixed, the rest you change if you need to **/
+#define IRQ_EMU			0	/* Emulation */
+#define IRQ_RST			1	/* reset */
+#define IRQ_NMI			2	/* Non Maskable */
+#define IRQ_EVX			3	/* Exception */
+#define IRQ_UNUSED		4	/* - unused interrupt */
+#define IRQ_HWERR		5	/* Hardware Error */
+#define IRQ_CORETMR		6	/* Core timer */
+
+#define BFIN_IRQ(x)		((x) + 7)
+
+#define IRQ_PLL_WAKEUP		BFIN_IRQ(0)	/* PLL Wakeup Interrupt */
+#define IRQ_DMA0_ERROR		BFIN_IRQ(1)	/* DMA Error 0 (generic) */
+#define IRQ_DMAR0_BLK		BFIN_IRQ(2)	/* DMAR0 Block Interrupt */
+#define IRQ_DMAR1_BLK		BFIN_IRQ(3)	/* DMAR1 Block Interrupt */
+#define IRQ_DMAR0_OVR		BFIN_IRQ(4)	/* DMAR0 Overflow Error */
+#define IRQ_DMAR1_OVR		BFIN_IRQ(5)	/* DMAR1 Overflow Error */
+#define IRQ_PPI_ERROR		BFIN_IRQ(6)	/* PPI Error */
+#define IRQ_MAC_ERROR		BFIN_IRQ(7)	/* MAC Status */
+#define IRQ_SPORT0_ERROR	BFIN_IRQ(8)	/* SPORT0 Status */
+#define IRQ_SPORT1_ERROR	BFIN_IRQ(9)	/* SPORT1 Status */
+#define IRQ_UART0_ERROR		BFIN_IRQ(12)	/* UART0 Status */
+#define IRQ_UART1_ERROR		BFIN_IRQ(13)	/* UART1 Status */
+#define IRQ_RTC			BFIN_IRQ(14)	/* RTC */
+#define IRQ_PPI      		BFIN_IRQ(15)	/* DMA Channel 0 (PPI/NAND) */
+#define IRQ_SPORT0_RX		BFIN_IRQ(16)	/* DMA 3 Channel (SPORT0 RX) */
+#define IRQ_SPORT0_TX		BFIN_IRQ(17)	/* DMA 4 Channel (SPORT0 TX) */
+#define IRQ_SPORT1_RX		BFIN_IRQ(18)	/* DMA 5 Channel (SPORT1 RX) */
+#define IRQ_SPORT1_TX		BFIN_IRQ(19)	/* DMA 6 Channel (SPORT1 TX) */
+#define IRQ_TWI      		BFIN_IRQ(20)	/* TWI */
+#define IRQ_SPI      		BFIN_IRQ(21)	/* DMA 7 Channel (SPI) */
+#define IRQ_UART0_RX 		BFIN_IRQ(22)	/* DMA8 Channel (UART0 RX) */
+#define IRQ_UART0_TX 		BFIN_IRQ(23)	/* DMA9 Channel (UART0 TX) */
+#define IRQ_UART1_RX 		BFIN_IRQ(24)	/* DMA10 Channel (UART1 RX) */
+#define IRQ_UART1_TX 		BFIN_IRQ(25)	/* DMA11 Channel (UART1 TX) */
+#define IRQ_OPTSEC   		BFIN_IRQ(26)	/* OTPSEC Interrupt */
+#define IRQ_CNT   		BFIN_IRQ(27)	/* GP Counter */
+#define IRQ_MAC_RX   		BFIN_IRQ(28)	/* DMA1 Channel (MAC RX/HDMA) */
+#define IRQ_PORTH_INTA   	BFIN_IRQ(29)	/* Port H Interrupt A */
+#define IRQ_MAC_TX		BFIN_IRQ(30)	/* DMA2 Channel (MAC TX/NAND) */
+#define IRQ_NFC			BFIN_IRQ(30)	/* DMA2 Channel (MAC TX/NAND) */
+#define IRQ_PORTH_INTB		BFIN_IRQ(31)	/* Port H Interrupt B */
+#define IRQ_TMR0		BFIN_IRQ(32)	/* Timer 0 */
+#define IRQ_TMR1		BFIN_IRQ(33)	/* Timer 1 */
+#define IRQ_TMR2		BFIN_IRQ(34)	/* Timer 2 */
+#define IRQ_TMR3		BFIN_IRQ(35)	/* Timer 3 */
+#define IRQ_TMR4		BFIN_IRQ(36)	/* Timer 4 */
+#define IRQ_TMR5		BFIN_IRQ(37)	/* Timer 5 */
+#define IRQ_TMR6		BFIN_IRQ(38)	/* Timer 6 */
+#define IRQ_TMR7		BFIN_IRQ(39)	/* Timer 7 */
+#define IRQ_PORTG_INTA		BFIN_IRQ(40)	/* Port G Interrupt A */
+#define IRQ_PORTG_INTB		BFIN_IRQ(41)	/* Port G Interrupt B */
+#define IRQ_MEM_DMA0		BFIN_IRQ(42)	/* MDMA Stream 0 */
+#define IRQ_MEM_DMA1		BFIN_IRQ(43)	/* MDMA Stream 1 */
+#define IRQ_WATCH		BFIN_IRQ(44)	/* Software Watchdog Timer */
+#define IRQ_PORTF_INTA		BFIN_IRQ(45)	/* Port F Interrupt A */
+#define IRQ_PORTF_INTB		BFIN_IRQ(46)	/* Port F Interrupt B */
+#define IRQ_SPI_ERROR		BFIN_IRQ(47)	/* SPI Status */
+#define IRQ_NFC_ERROR		BFIN_IRQ(48)	/* NAND Error */
+#define IRQ_HDMA_ERROR		BFIN_IRQ(49)	/* HDMA Error */
+#define IRQ_HDMA		BFIN_IRQ(50)	/* HDMA (TFI) */
+#define IRQ_USB_EINT		BFIN_IRQ(51)	/* USB_EINT Interrupt */
+#define IRQ_USB_INT0		BFIN_IRQ(52)	/* USB_INT0 Interrupt */
+#define IRQ_USB_INT1		BFIN_IRQ(53)	/* USB_INT1 Interrupt */
+#define IRQ_USB_INT2		BFIN_IRQ(54)	/* USB_INT2 Interrupt */
+#define IRQ_USB_DMA		BFIN_IRQ(55)	/* USB_DMAINT Interrupt */
+
+#define SYS_IRQS        	BFIN_IRQ(63)	/* 70 */
+
+#define IRQ_PF0         71
+#define IRQ_PF1         72
+#define IRQ_PF2         73
+#define IRQ_PF3         74
+#define IRQ_PF4         75
+#define IRQ_PF5         76
+#define IRQ_PF6         77
+#define IRQ_PF7         78
+#define IRQ_PF8         79
+#define IRQ_PF9         80
+#define IRQ_PF10        81
+#define IRQ_PF11        82
+#define IRQ_PF12        83
+#define IRQ_PF13        84
+#define IRQ_PF14        85
+#define IRQ_PF15        86
+
+#define IRQ_PG0         87
+#define IRQ_PG1         88
+#define IRQ_PG2         89
+#define IRQ_PG3         90
+#define IRQ_PG4         91
+#define IRQ_PG5         92
+#define IRQ_PG6         93
+#define IRQ_PG7         94
+#define IRQ_PG8         95
+#define IRQ_PG9         96
+#define IRQ_PG10        97
+#define IRQ_PG11        98
+#define IRQ_PG12        99
+#define IRQ_PG13        100
+#define IRQ_PG14        101
+#define IRQ_PG15        102
+
+#define IRQ_PH0         103
+#define IRQ_PH1         104
+#define IRQ_PH2         105
+#define IRQ_PH3         106
+#define IRQ_PH4         107
+#define IRQ_PH5         108
+#define IRQ_PH6         109
+#define IRQ_PH7         110
+#define IRQ_PH8         111
+#define IRQ_PH9         112
+#define IRQ_PH10        113
+#define IRQ_PH11        114
+#define IRQ_PH12        115
+#define IRQ_PH13        116
+#define IRQ_PH14        117
+#define IRQ_PH15        118
+
+#define GPIO_IRQ_BASE	IRQ_PF0
+
+#ifdef CONFIG_IRQCHIP_DEMUX_GPIO
+#define NR_IRQS     (IRQ_PH15+1)
+#else
+#define NR_IRQS     (SYS_IRQS+1)
+#endif
+
+#define IVG7            7
+#define IVG8            8
+#define IVG9            9
+#define IVG10           10
+#define IVG11           11
+#define IVG12           12
+#define IVG13           13
+#define IVG14           14
+#define IVG15           15
+
+/* IAR0 BIT FIELDS */
+#define IRQ_PLL_WAKEUP_POS	0
+#define IRQ_DMA0_ERROR_POS	4
+#define IRQ_DMAR0_BLK_POS 	8
+#define IRQ_DMAR1_BLK_POS 	12
+#define IRQ_DMAR0_OVR_POS 	16
+#define IRQ_DMAR1_OVR_POS 	20
+#define IRQ_PPI_ERROR_POS 	24
+#define IRQ_MAC_ERROR_POS 	28
+
+/* IAR1 BIT FIELDS */
+#define IRQ_SPORT0_ERROR_POS	0
+#define IRQ_SPORT1_ERROR_POS	4
+#define IRQ_UART0_ERROR_POS 	16
+#define IRQ_UART1_ERROR_POS 	20
+#define IRQ_RTC_POS         	24
+#define IRQ_PPI_POS         	28
+
+/* IAR2 BIT FIELDS */
+#define IRQ_SPORT0_RX_POS	0
+#define IRQ_SPORT0_TX_POS	4
+#define IRQ_SPORT1_RX_POS	8
+#define IRQ_SPORT1_TX_POS	12
+#define IRQ_TWI_POS      	16
+#define IRQ_SPI_POS      	20
+#define IRQ_UART0_RX_POS 	24
+#define IRQ_UART0_TX_POS 	28
+
+/* IAR3 BIT FIELDS */
+#define IRQ_UART1_RX_POS  	0
+#define IRQ_UART1_TX_POS  	4
+#define IRQ_OPTSEC_POS    	8
+#define IRQ_CNT_POS       	12
+#define IRQ_MAC_RX_POS    	16
+#define IRQ_PORTH_INTA_POS	20
+#define IRQ_MAC_TX_POS    	24
+#define IRQ_PORTH_INTB_POS	28
+
+/* IAR4 BIT FIELDS */
+#define IRQ_TMR0_POS		0
+#define IRQ_TMR1_POS		4
+#define IRQ_TMR2_POS		8
+#define IRQ_TMR3_POS		12
+#define IRQ_TMR4_POS		16
+#define IRQ_TMR5_POS		20
+#define IRQ_TMR6_POS		24
+#define IRQ_TMR7_POS		28
+
+/* IAR5 BIT FIELDS */
+#define IRQ_PORTG_INTA_POS	0
+#define IRQ_PORTG_INTB_POS	4
+#define IRQ_MEM_DMA0_POS  	8
+#define IRQ_MEM_DMA1_POS  	12
+#define IRQ_WATCH_POS     	16
+#define IRQ_PORTF_INTA_POS	20
+#define IRQ_PORTF_INTB_POS	24
+#define IRQ_SPI_ERROR_POS 	28
+
+/* IAR6 BIT FIELDS */
+#define IRQ_NFC_ERROR_POS  	0
+#define IRQ_HDMA_ERROR_POS 	4
+#define IRQ_HDMA_POS       	8
+#define IRQ_USB_EINT_POS   	12
+#define IRQ_USB_INT0_POS   	16
+#define IRQ_USB_INT1_POS   	20
+#define IRQ_USB_INT2_POS   	24
+#define IRQ_USB_DMA_POS    	28
+
+#endif				/* _BF527_IRQ_H_ */

include/asm-blackfin/mach-bf527/mem_init.h

+/*
+ * File:         include/asm-blackfin/mach-bf527/mem_init.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || CONFIG_MEM_MT48LC16M8A2TG_75 || CONFIG_MEM_GENERIC_BOARD || CONFIG_MEM_MT48LC32M8A2_75 || CONFIG_MEM_MT48LC32M16A2TG_75)
+#if (CONFIG_SCLK_HZ > 119402985)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_7
+#define SDRAM_tRAS_num  7
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 104477612) && (CONFIG_SCLK_HZ <= 119402985)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_6
+#define SDRAM_tRAS_num  6
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_5
+#define SDRAM_tRAS_num  5
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 74626866) && (CONFIG_SCLK_HZ <= 89552239)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_4
+#define SDRAM_tRAS_num  4
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 66666667) && (CONFIG_SCLK_HZ <= 74626866)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_3
+#define SDRAM_tRAS_num  3
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 59701493) && (CONFIG_SCLK_HZ <= 66666667)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_4
+#define SDRAM_tRAS_num  3
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 44776119) && (CONFIG_SCLK_HZ <= 59701493)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_3
+#define SDRAM_tRAS_num  3
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 29850746) && (CONFIG_SCLK_HZ <= 44776119)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_2
+#define SDRAM_tRAS_num  2
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ <= 29850746)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_1
+#define SDRAM_tRAS_num  1
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#endif
+
+#if (CONFIG_MEM_MT48LC16M16A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC16M8A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   4096	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC32M8A2_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC64M4A2FB_7E)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_GENERIC_BOARD)
+  /*SDRAM INFORMATION: Modify this for your board */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC32M16A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_SIZE == 128)
+#define SDRAM_SIZE      EBSZ_128
+#endif
+#if (CONFIG_MEM_SIZE == 64)
+#define SDRAM_SIZE      EBSZ_64
+#endif
+#if (CONFIG_MEM_SIZE == 32)
+#define SDRAM_SIZE      EBSZ_32
+#endif
+#if (CONFIG_MEM_SIZE == 16)
+#define SDRAM_SIZE      EBSZ_16
+#endif
+#if (CONFIG_MEM_ADD_WIDTH == 11)
+#define SDRAM_WIDTH     EBCAW_11
+#endif
+#if (CONFIG_MEM_ADD_WIDTH == 10)
+#define SDRAM_WIDTH     EBCAW_10
+#endif
+#if (CONFIG_MEM_ADD_WIDTH == 9)
+#define SDRAM_WIDTH     EBCAW_9
+#endif
+#if (CONFIG_MEM_ADD_WIDTH == 8)
+#define SDRAM_WIDTH     EBCAW_8
+#endif
+
+#define mem_SDBCTL      (SDRAM_WIDTH | SDRAM_SIZE | EBE)
+
+/* Equation from section 17 (p17-46) of BF533 HRM */
+#define mem_SDRRC       (((CONFIG_SCLK_HZ / 1000) * SDRAM_Tref) / SDRAM_NRA) - (SDRAM_tRAS_num + SDRAM_tRP_num)
+
+/* Enable SCLK Out */
+#define mem_SDGCTL        (SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR | PSS)
+
+#if defined CONFIG_CLKIN_HALF
+#define CLKIN_HALF       1
+#else
+#define CLKIN_HALF       0
+#endif
+
+#if defined CONFIG_PLL_BYPASS
+#define PLL_BYPASS      1
+#else
+#define PLL_BYPASS       0
+#endif
+
+/***************************************Currently Not Being Used *********************************/
+#define flash_EBIU_AMBCTL_WAT  ((CONFIG_FLASH_SPEED_BWAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_RAT  ((CONFIG_FLASH_SPEED_BRAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_HT   ((CONFIG_FLASH_SPEED_BHT  * 4) / (4000000000 / CONFIG_SCLK_HZ))
+#define flash_EBIU_AMBCTL_ST   ((CONFIG_FLASH_SPEED_BST  * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_TT   ((CONFIG_FLASH_SPEED_BTT  * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+
+#if (flash_EBIU_AMBCTL_TT > 3)
+#define flash_EBIU_AMBCTL0_TT   B0TT_4
+#endif
+#if (flash_EBIU_AMBCTL_TT == 3)
+#define flash_EBIU_AMBCTL0_TT   B0TT_3
+#endif
+#if (flash_EBIU_AMBCTL_TT == 2)
+#define flash_EBIU_AMBCTL0_TT   B0TT_2
+#endif
+#if (flash_EBIU_AMBCTL_TT < 2)
+#define flash_EBIU_AMBCTL0_TT   B0TT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_ST > 3)
+#define flash_EBIU_AMBCTL0_ST   B0ST_4
+#endif
+#if (flash_EBIU_AMBCTL_ST == 3)
+#define flash_EBIU_AMBCTL0_ST   B0ST_3
+#endif
+#if (flash_EBIU_AMBCTL_ST == 2)
+#define flash_EBIU_AMBCTL0_ST   B0ST_2
+#endif
+#if (flash_EBIU_AMBCTL_ST < 2)
+#define flash_EBIU_AMBCTL0_ST   B0ST_1
+#endif
+
+#if (flash_EBIU_AMBCTL_HT > 2)
+#define flash_EBIU_AMBCTL0_HT   B0HT_3
+#endif
+#if (flash_EBIU_AMBCTL_HT == 2)
+#define flash_EBIU_AMBCTL0_HT   B0HT_2
+#endif
+#if (flash_EBIU_AMBCTL_HT == 1)
+#define flash_EBIU_AMBCTL0_HT   B0HT_1
+#endif
+#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT == 0)
+#define flash_EBIU_AMBCTL0_HT   B0HT_0
+#endif
+#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT != 0)
+#define flash_EBIU_AMBCTL0_HT   B0HT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_WAT > 14)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_15
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 14)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_14
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 13)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_13
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 12)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_12
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 11)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_11
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 10)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_10
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 9)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_9
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 8)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_8
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 7)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_7
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 6)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_6
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 5)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_5
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 4)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_4
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 3)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_3
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 2)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_2
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 1)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_RAT > 14)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_15
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 14)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_14
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 13)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_13
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 12)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_12
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 11)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_11
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 10)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_10
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 9)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_9
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 8)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_8
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 7)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_7
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 6)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_6
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 5)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_5
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 4)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_4
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 3)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_3
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 2)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_2
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 1)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_1
+#endif
+
+#define flash_EBIU_AMBCTL0  \
+	(flash_EBIU_AMBCTL0_WAT | flash_EBIU_AMBCTL0_RAT | flash_EBIU_AMBCTL0_HT | \
+	 flash_EBIU_AMBCTL0_ST | flash_EBIU_AMBCTL0_TT | CONFIG_FLASH_SPEED_RDYEN)

include/asm-blackfin/mach-bf527/mem_map.h

+/*
+ * file:         include/asm-blackfin/mach-bf527/mem_map.h
+ * based on:	include/asm-blackfin/mach-bf537/mem_map.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	Memory MAP Common header file for blackfin BF527/5/2 of processors.
+ * rev:
+ *
+ * modified:
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _MEM_MAP_527_H_
+#define _MEM_MAP_527_H_
+
+#define COREMMR_BASE           0xFFE00000	/* Core MMRs */
+#define SYSMMR_BASE            0xFFC00000	/* System MMRs */
+
+/* Async Memory Banks */
+#define ASYNC_BANK3_BASE	0x20300000	/* Async Bank 3 */
+#define ASYNC_BANK3_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK2_BASE	0x20200000	/* Async Bank 2 */
+#define ASYNC_BANK2_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK1_BASE	0x20100000	/* Async Bank 1 */
+#define ASYNC_BANK1_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK0_BASE	0x20000000	/* Async Bank 0 */
+#define ASYNC_BANK0_SIZE	0x00100000	/* 1M */
+
+/* Boot ROM Memory */
+
+#define BOOT_ROM_START		0xEF000000
+
+/* Level 1 Memory */
+
+/* Memory Map for ADSP-BF527 ADSP-BF525 ADSP-BF522 processors */
+
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE	(16*1024)
+#else
+#define BFIN_ICACHESIZE	(0*1024)
+#endif
+
+#define L1_CODE_START       0xFFA00000
+#define L1_DATA_A_START     0xFF800000
+#define L1_DATA_B_START     0xFF900000
+
+#define L1_CODE_LENGTH      0xC000
+
+#ifdef CONFIG_BFIN_DCACHE
+
+#ifdef CONFIG_BFIN_DCACHE_BANKA
+#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH      (0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH      0x8000
+#define BFIN_DCACHESIZE	(16*1024)
+#define BFIN_DSUPBANKS	1
+#else
+#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH      (0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH      (0x8000 - 0x4000)
+#define BFIN_DCACHESIZE	(32*1024)
+#define BFIN_DSUPBANKS	2
+#endif
+
+#else
+#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH      0x8000
+#define L1_DATA_B_LENGTH      0x8000
+#define BFIN_DCACHESIZE	(0*1024)
+#define BFIN_DSUPBANKS	0
+#endif				/*CONFIG_BFIN_DCACHE */
+
+/* Scratch Pad Memory */
+
+#if defined(CONFIG_BF527) || defined(CONFIG_BF536) || defined(CONFIG_BF534)
+#define L1_SCRATCH_START	0xFFB00000
+#define L1_SCRATCH_LENGTH	0x1000
+#endif
+
+#endif				/* _MEM_MAP_527_H_ */

include/asm-blackfin/mach-bf527/portmux.h

+#ifndef _MACH_PORTMUX_H_
+#define _MACH_PORTMUX_H_
+
+#define P_PPI0_D0	(P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(0))
+#define P_PPI0_D1	(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(0))
+#define P_PPI0_D2	(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(0))
+#define P_PPI0_D3	(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(0))
+#define P_PPI0_D4	(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(0))
+#define P_PPI0_D5	(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(0))
+#define P_PPI0_D6	(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(0))
+#define P_PPI0_D7	(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(0))
+#define P_PPI0_D8	(P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(0))
+#define P_PPI0_D9	(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(0))
+#define P_PPI0_D10	(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(0))
+#define P_PPI0_D11	(P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(0))
+#define P_PPI0_D12	(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(0))
+#define P_PPI0_D13	(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(0))
+#define P_PPI0_D14	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(0))
+#define P_PPI0_D15	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(0))
+
+#if defined(CONFIG_BF527_SPORT0_PORTF)
+#define P_SPORT0_DRPRI	(P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(1))
+#define P_SPORT0_RFS	(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(1))
+#define P_SPORT0_RSCLK	(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(1))
+#define P_SPORT0_DTPRI	(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(1))
+#define P_SPORT0_TFS	(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(1))
+#define P_SPORT0_TSCLK	(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(1))
+#define P_SPORT0_DTSEC	(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(1))
+#define P_SPORT0_DRSEC	(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(1))
+#elif defined(CONFIG_BF527_SPORT0_PORTG)
+#define P_SPORT0_DTPRI	(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(0))
+#define P_SPORT0_DRSEC	(P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1))
+#define P_SPORT0_DTSEC	(P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(1))
+#define P_SPORT0_DRPRI	(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(1))
+#define P_SPORT0_RFS	(P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(1))
+#define P_SPORT0_RSCLK	(P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(1))
+#if defined(CONFIG_BF527_SPORT0_TSCLK_PG10)
+#define P_SPORT0_TSCLK	(P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(1))
+#elif defined(CONFIG_BF527_SPORT0_TSCLK_PG14)
+#define P_SPORT0_TSCLK	(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(0))
+#endif
+#define P_SPORT0_TFS	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(0))
+#endif
+
+#define P_SPORT1_DRPRI	(P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(1))
+#define P_SPORT1_RSCLK	(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(1))
+#define P_SPORT1_RFS	(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(1))
+#define P_SPORT1_TFS	(P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(1))
+#define P_SPORT1_DTPRI	(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(1))
+#define P_SPORT1_TSCLK	(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(1))
+#define P_SPORT1_DTSEC	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1))
+#define P_SPORT1_DRSEC	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1))
+
+#define P_SPI0_SSEL6	(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(2))
+#define P_SPI0_SSEL7	(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(2))
+
+#define P_SPI0_SSEL2	(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(2))
+#define P_SPI0_SSEL3	(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(2))
+
+#if defined(CONFIG_BF527_UART1_PORTF)
+#define P_UART1_TX	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(2))
+#define P_UART1_RX	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(2))
+#elif defined(CONFIG_BF527_UART1_PORTG)
+#define P_UART1_TX	(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(1))
+#define P_UART1_RX	(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(1))
+#endif
+
+#define P_HWAIT		(P_DONTCARE)
+
+#define P_SPI0_SS	(P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(0))
+#define P_SPI0_SSEL1	(P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(2))
+#define P_SPI0_SCK	(P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(2))
+#define P_SPI0_MISO	(P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(2))
+#define P_SPI0_MOSI	(P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(2))
+#define P_TMR1		(P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0))
+#define P_PPI0_FS2	(P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0))
+#define P_TMR3		(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(0))
+#define P_TMR4		(P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(0))
+#define P_TMR5		(P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(0))
+#define P_TMR6		(P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(0))
+/* #define P_TMR7		(P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(0)) */
+#define P_DMAR1		(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(0))
+#define P_DMAR0		(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(0))
+#define P_TMR2		(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(1))
+#define P_TMR7		(P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(1))
+#define P_MDC		(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(1))
+#define P_RMII0_MDINT	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1))
+#define P_MII0_PHYINT	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1))
+
+#define P_PPI0_FS3	(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(2))
+#define P_UART0_TX	(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(2))
+#define P_UART0_RX	(P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(2))
+
+#define P_HOST_WR	(P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(2))
+#define P_HOST_ACK	(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(2))
+#define P_HOST_ADDR	(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(2))
+#define P_HOST_RD	(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(2))
+#define P_HOST_CE	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(2))
+
+#if defined(CONFIG_BF527_NAND_D_PORTF)
+#define P_NAND_D0	(P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(2))
+#define P_NAND_D1	(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(2))
+#define P_NAND_D2	(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(2))
+#define P_NAND_D3	(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(2))
+#define P_NAND_D4	(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(2))
+#define P_NAND_D5	(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(2))
+#define P_NAND_D6	(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(2))
+#define P_NAND_D7	(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(2))
+#elif defined(CONFIG_BF527_NAND_D_PORTH)
+#define P_NAND_D0	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(0))
+#define P_NAND_D1	(P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(0))
+#define P_NAND_D2	(P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(0))
+#define P_NAND_D3	(P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(0))
+#define P_NAND_D4	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(0))
+#define P_NAND_D5	(P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(0))
+#define P_NAND_D6	(P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(0))
+#define P_NAND_D7	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(0))
+#endif
+
+#define P_SPI0_SSEL4	(P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(0))
+#define P_SPI0_SSEL5	(P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(0))
+#define P_NAND_CE	(P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(0))
+#define P_NAND_WE	(P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(0))
+#define P_NAND_RE	(P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(0))
+#define P_NAND_RB	(P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(0))
+#define P_NAND_CLE	(P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(0))
+#define P_NAND_ALE	(P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(0))
+
+#define P_HOST_D0	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(2))
+#define P_HOST_D1	(P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(2))
+#define P_HOST_D2	(P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(2))
+#define P_HOST_D3	(P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(2))
+#define P_HOST_D4	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(2))
+#define P_HOST_D5	(P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(2))
+#define P_HOST_D6	(P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(2))
+#define P_HOST_D7	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(2))
+#define P_HOST_D8	(P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(2))
+#define P_HOST_D9	(P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(2))
+#define P_HOST_D10	(P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(2))
+#define P_HOST_D11	(P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(2))
+#define P_HOST_D12	(P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(2))
+#define P_HOST_D13	(P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(2))
+#define P_HOST_D14	(P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(2))
+#define P_HOST_D15	(P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(2))
+
+#define P_MII0_ETxD0	(P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(1))
+#define P_MII0_ETxD1	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(1))
+#define P_MII0_ETxD2	(P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(1))
+#define P_MII0_ETxD3	(P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(1))
+#define P_MII0_ETxEN	(P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(1))
+#define P_MII0_TxCLK	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(1))
+#define P_MII0_COL	(P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(1))
+#define P_MII0_ERxD0	(P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(1))
+#define P_MII0_ERxD1	(P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(1))
+#define P_MII0_ERxD2	(P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(1))
+#define P_MII0_ERxD3	(P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(1))
+#define P_MII0_ERxDV	(P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(1))
+#define P_MII0_ERxCLK	(P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(1))
+#define P_MII0_ERxER	(P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(1))
+#define P_MII0_CRS	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1))
+#define P_RMII0_REF_CLK	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(1))
+#define P_RMII0_CRS_DV	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1))
+#define P_MDIO		(P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(1))
+
+#define P_TWI0_SCL	(P_DONTCARE)
+#define P_TWI0_SDA	(P_DONTCARE)
+#define P_PPI0_FS1	(P_DONTCARE)
+#define P_TMR0		(P_DONTCARE)
+#define P_TMRCLK	(P_DONTCARE)
+#define P_PPI0_CLK	(P_DONTCARE)
+
+#define P_MII0 {\
+	P_MII0_ETxD0, \
+	P_MII0_ETxD1, \
+	P_MII0_ETxD2, \
+	P_MII0_ETxD3, \
+	P_MII0_ETxEN, \
+	P_MII0_TxCLK, \
+	P_MII0_PHYINT, \
+	P_MII0_COL, \
+	P_MII0_ERxD0, \
+	P_MII0_ERxD1, \
+	P_MII0_ERxD2, \
+	P_MII0_ERxD3, \
+	P_MII0_ERxDV, \
+	P_MII0_ERxCLK, \
+	P_MII0_ERxER, \
+	P_MII0_CRS, \
+	P_MDC, \
+	P_MDIO, 0}
+
+#define P_RMII0 {\
+	P_MII0_ETxD0, \
+	P_MII0_ETxD1, \
+	P_MII0_ETxEN, \
+	P_MII0_ERxD0, \
+	P_MII0_ERxD1, \
+	P_MII0_ERxER, \
+	P_RMII0_REF_CLK, \
+	P_RMII0_MDINT, \
+	P_RMII0_CRS_DV, \
+	P_MDC, \
+	P_MDIO, 0}
+
+#endif				/* _MACH_PORTMUX_H_ */