m68knommu: move UART addressing to part specific includes

The ColdFire UART base addresses varies between the different ColdFire
family members. Instead of keeping the base addresses with the UART
definitions keep them with the other addresses definitions for each
ColdFire part.

The motivation for this move is so that when we add new ColdFire
part definitions, they are all in a single file (and we shouldn't
normally need to modify the UART definitions in mcfuart.h at all).
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

arch/m68k/include/asm/m5206sim.h

@@ -90,6 +90,14 @@
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x1c5)	/* Parallel Direction (r/w) */
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x1c9)	/* Parallel Port Value (r/w) */
 
+#if defined(CONFIG_NETtel)
+#define	MCFUART_BASE1		0x180		/* Base address of UART1 */
+#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
+#else
+#define	MCFUART_BASE1		0x140		/* Base address of UART1 */
+#define	MCFUART_BASE2		0x180		/* Base address of UART2 */
+#endif
+
 /*
  *	Define system peripheral IRQ usage.
  */
@@ -97,7 +105,7 @@
 #define	MCF_IRQ_PROFILER	31		/* Timer1, Level 7 */
 
 /*
- * Generic GPIO
+ *	Generic GPIO
  */
 #define MCFGPIO_PIN_MAX		8
 #define MCFGPIO_IRQ_VECBASE	-1

arch/m68k/include/asm/m520xsim.h

@@ -100,6 +100,7 @@
 #define MCFGPIO_PCLRR_UART		0xFC0A402A
 #define MCFGPIO_PCLRR_FECH		0xFC0A402B
 #define MCFGPIO_PCLRR_FECL		0xFC0A402C
+
 /*
  * Generic GPIO support
  */
@@ -112,7 +113,6 @@
 #define MCFGPIO_PIN_MAX			80
 #define MCFGPIO_IRQ_MAX			8
 #define MCFGPIO_IRQ_VECBASE		MCFINT_VECBASE
-/****************************************************************************/
 
 #define MCF_GPIO_PAR_UART                   (0xA4036)
 #define MCF_GPIO_PAR_FECI2C                 (0xA4033)
@@ -128,6 +128,13 @@
 #define MCF_GPIO_PAR_FECI2C_PAR_SDA_URXD2   (0x02)
 #define MCF_GPIO_PAR_FECI2C_PAR_SCL_UTXD2   (0x04)
 
+/*
+ *  UART module.
+ */
+#define MCFUART_BASE1		0x60000		/* Base address of UART1 */
+#define MCFUART_BASE2		0x64000		/* Base address of UART2 */
+#define MCFUART_BASE3		0x68000		/* Base address of UART2 */
+
 /*
  *  Reset Controll Unit.
  */

arch/m68k/include/asm/m523xsim.h

@@ -52,6 +52,13 @@
 #define	MCF_RCR_SWRESET		0x80		/* Software reset bit */
 #define	MCF_RCR_FRCSTOUT	0x40		/* Force external reset */
 
+/*
+ *  UART module.
+ */
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x240           /* Base address of UART2 */
+#define MCFUART_BASE3		0x280           /* Base address of UART3 */
+
 #define MCFGPIO_PODR_ADDR	(MCF_IPSBAR + 0x100000)
 #define MCFGPIO_PODR_DATAH	(MCF_IPSBAR + 0x100001)
 #define MCFGPIO_PODR_DATAL	(MCF_IPSBAR + 0x100002)

arch/m68k/include/asm/m5249sim.h

@@ -59,6 +59,11 @@
 #define MCFSIM_DACR1		0x110		/* DRAM 1 Addr and Ctrl (r/w) */
 #define MCFSIM_DMR1		0x114		/* DRAM 1 Mask reg (r/w) */
 
+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
+#define MCFUART_BASE2		0x200           /* Base address of UART2 */
 
 /*
  *	Some symbol defines for the above...

arch/m68k/include/asm/m5272sim.h

@@ -65,6 +65,9 @@
 #define	MCFSIM_DCMR1		0x5c		/* DRAM 1 Mask reg (r/w) */
 #define	MCFSIM_DCCR1		0x63		/* DRAM 1 Control reg (r/w) */
 
+#define	MCFUART_BASE1		0x100		/* Base address of UART1 */
+#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
+
 #define	MCFSIM_PACNT		(MCF_MBAR + 0x80) /* Port A Control (r/w) */
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x84) /* Port A Direction (r/w) */
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x86) /* Port A Data (r/w) */

arch/m68k/include/asm/m527xsim.h

@@ -58,6 +58,12 @@
 #define	MCFSIM_DMR1		0x5c		/* SDRAM address mask 1 */
 #endif
 
+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x240           /* Base address of UART2 */
+#define MCFUART_BASE3		0x280           /* Base address of UART3 */
 
 #ifdef CONFIG_M5271
 #define MCFGPIO_PODR_ADDR	(MCF_IPSBAR + 0x100000)

arch/m68k/include/asm/m528xsim.h

@@ -43,6 +43,13 @@
 #define	MCFSIM_DACR1		0x50		/* SDRAM base address 1 */
 #define	MCFSIM_DMR1		0x54		/* SDRAM address mask 1 */
 
+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x240           /* Base address of UART2 */
+#define MCFUART_BASE3		0x280           /* Base address of UART3 */
+
 /*
  * 	GPIO registers
  */

arch/m68k/include/asm/m5307sim.h

@@ -96,6 +96,17 @@
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x244)
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x248)
 
+/*
+ *  UART module.
+ */
+#if defined(CONFIG_NETtel) || defined(CONFIG_SECUREEDGEMP3)
+#define MCFUART_BASE1		0x200           /* Base address of UART1 */
+#define MCFUART_BASE2		0x1c0           /* Base address of UART2 */
+#else
+#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
+#define MCFUART_BASE2		0x200           /* Base address of UART2 */
+#endif
+
 /*
  * Generic GPIO support
  */

arch/m68k/include/asm/m532xsim.h

@@ -103,6 +103,13 @@
 #define	ACR_CM_OFF_IMP		(3<<5)
 #define	ACR_WPROTECT		(1<<2)
 
+/*
+ *  UART module.
+ */
+#define MCFUART_BASE1		0xFC060000	/* Base address of UART1 */
+#define MCFUART_BASE2		0xFC064000	/* Base address of UART2 */
+#define MCFUART_BASE3		0xFC068000	/* Base address of UART3 */
+
 /*********************************************************************
  *
  * Reset Controller Module

arch/m68k/include/asm/m5407sim.h

@@ -76,6 +76,9 @@
 #define MCFSIM_DACR1		0x110		/* DRAM 1 Addr and Ctrl (r/w) */
 #define MCFSIM_DMR1		0x114		/* DRAM 1 Mask reg (r/w) */
 
+#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
+#define MCFUART_BASE2		0x200           /* Base address of UART2 */
+
 #define	MCFSIM_PADDR		(MCF_MBAR + 0x244)
 #define	MCFSIM_PADAT		(MCF_MBAR + 0x248)
 

arch/m68k/include/asm/m54xxsim.h

@@ -24,6 +24,14 @@
 #define MCFINTC_IACKL		0x19		/* */
 #define MCFINTC_ICR0		0x40		/* Base ICR register */
 
+/*
+ *	UART module.
+ */
+#define MCFUART_BASE1		0x8600		/* Base address of UART1 */
+#define MCFUART_BASE2		0x8700		/* Base address of UART2 */
+#define MCFUART_BASE3		0x8800		/* Base address of UART3 */
+#define MCFUART_BASE4		0x8900		/* Base address of UART4 */
+
 /*
  *	Define system peripheral IRQ usage.
  */

arch/m68k/include/asm/mcfuart.h

@@ -12,49 +12,6 @@
 #define	mcfuart_h
 /****************************************************************************/
 
-/*
- *	Define the base address of the UARTS within the MBAR address
- *	space.
- */
-#if defined(CONFIG_M5272)
-#define	MCFUART_BASE1		0x100		/* Base address of UART1 */
-#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
-#elif defined(CONFIG_M5206) || defined(CONFIG_M5206e)
-#if defined(CONFIG_NETtel)
-#define	MCFUART_BASE1		0x180		/* Base address of UART1 */
-#define	MCFUART_BASE2		0x140		/* Base address of UART2 */
-#else
-#define	MCFUART_BASE1		0x140		/* Base address of UART1 */
-#define	MCFUART_BASE2		0x180		/* Base address of UART2 */
-#endif
-#elif defined(CONFIG_M523x) || defined(CONFIG_M527x) || defined(CONFIG_M528x)
-#define MCFUART_BASE1		0x200           /* Base address of UART1 */
-#define MCFUART_BASE2		0x240           /* Base address of UART2 */
-#define MCFUART_BASE3		0x280           /* Base address of UART3 */
-#elif defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407)
-#if defined(CONFIG_NETtel) || defined(CONFIG_SECUREEDGEMP3)
-#define MCFUART_BASE1		0x200           /* Base address of UART1 */
-#define MCFUART_BASE2		0x1c0           /* Base address of UART2 */
-#else
-#define MCFUART_BASE1		0x1c0           /* Base address of UART1 */
-#define MCFUART_BASE2		0x200           /* Base address of UART2 */
-#endif
-#elif defined(CONFIG_M520x)
-#define MCFUART_BASE1		0x60000		/* Base address of UART1 */
-#define MCFUART_BASE2		0x64000		/* Base address of UART2 */
-#define MCFUART_BASE3		0x68000		/* Base address of UART2 */
-#elif defined(CONFIG_M532x)
-#define MCFUART_BASE1		0xfc060000	/* Base address of UART1 */
-#define MCFUART_BASE2		0xfc064000	/* Base address of UART2 */
-#define MCFUART_BASE3		0xfc068000	/* Base address of UART3 */
-#elif defined(CONFIG_M54xx)
-#define MCFUART_BASE1		0x8600		/* on M54xx */
-#define MCFUART_BASE2		0x8700		/* on M54xx */
-#define MCFUART_BASE3		0x8800		/* on M54xx */
-#define MCFUART_BASE4		0x8900		/* on M54xx */
-#endif
-
-
 #include <linux/serial_core.h>
 #include <linux/platform_device.h>