i40e: Fix overwriting flow control settings during driver loading

During driver loading flow control settings were written to FW
using a variable which was always zero, since it was being set
only by ethtool. This behavior has been corrected and driver
no longer overwrites the default FW/NVM settings.

Fixes: 373149fc ("i40e: Decrease the scope of rtnl lock")
Signed-off-by: NDawid Lukwinski <dawid.lukwinski@intel.com>
Signed-off-by: NMateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: NAleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

drivers/net/ethernet/intel/i40e/i40e_main.c

@@ -10005,7 +10005,6 @@ static void i40e_rebuild(struct i40e_pf *pf, bool reinit, bool lock_acquired)
 	int old_recovery_mode_bit = test_bit(__I40E_RECOVERY_MODE, pf->state);
 	struct i40e_vsi *vsi = pf->vsi[pf->lan_vsi];
 	struct i40e_hw *hw = &pf->hw;
-	u8 set_fc_aq_fail = 0;
 	i40e_status ret;
 	u32 val;
 	int v;
@@ -10131,13 +10130,6 @@ static void i40e_rebuild(struct i40e_pf *pf, bool reinit, bool lock_acquired)
 			 i40e_stat_str(&pf->hw, ret),
 			 i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
 
-	/* make sure our flow control settings are restored */
-	ret = i40e_set_fc(&pf->hw, &set_fc_aq_fail, true);
-	if (ret)
-		dev_dbg(&pf->pdev->dev, "setting flow control: ret = %s last_status = %s\n",
-			i40e_stat_str(&pf->hw, ret),
-			i40e_aq_str(&pf->hw, pf->hw.aq.asq_last_status));
-
 	/* Rebuild the VSIs and VEBs that existed before reset.
 	 * They are still in our local switch element arrays, so only
 	 * need to rebuild the switch model in the HW.
@@ -14720,7 +14712,6 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	int err;
 	u32 val;
 	u32 i;
-	u8 set_fc_aq_fail;
 
 	err = pci_enable_device_mem(pdev);
 	if (err)
@@ -15054,24 +15045,6 @@ static int i40e_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 	}
 	INIT_LIST_HEAD(&pf->vsi[pf->lan_vsi]->ch_list);
 
-	/* Make sure flow control is set according to current settings */
-	err = i40e_set_fc(hw, &set_fc_aq_fail, true);
-	if (set_fc_aq_fail & I40E_SET_FC_AQ_FAIL_GET)
-		dev_dbg(&pf->pdev->dev,
-			"Set fc with err %s aq_err %s on get_phy_cap\n",
-			i40e_stat_str(hw, err),
-			i40e_aq_str(hw, hw->aq.asq_last_status));
-	if (set_fc_aq_fail & I40E_SET_FC_AQ_FAIL_SET)
-		dev_dbg(&pf->pdev->dev,
-			"Set fc with err %s aq_err %s on set_phy_config\n",
-			i40e_stat_str(hw, err),
-			i40e_aq_str(hw, hw->aq.asq_last_status));
-	if (set_fc_aq_fail & I40E_SET_FC_AQ_FAIL_UPDATE)
-		dev_dbg(&pf->pdev->dev,
-			"Set fc with err %s aq_err %s on get_link_info\n",
-			i40e_stat_str(hw, err),
-			i40e_aq_str(hw, hw->aq.asq_last_status));
-
 	/* if FDIR VSI was set up, start it now */
 	for (i = 0; i < pf->num_alloc_vsi; i++) {
 		if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {