提交 478a3bab 编写于 作者: A Alan Stern 提交者: Greg Kroah-Hartman

[PATCH] USB: Always do usb-handoff

This revised patch (as586b) makes usb-handoff permanently true and no
longer a kernel boot parameter.  It also removes the piix3_usb quirk code;
that was nothing more than an early version of the USB handoff code
(written at a time when Intel's PIIX3 was about the only motherboard with
USB support).  And it adds identifiers for the three PCI USB controller
classes to pci_ids.h.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
上级 46f116ea
......@@ -1517,8 +1517,6 @@ running once the system is up.
uart6850= [HW,OSS]
Format: <io>,<irq>
usb-handoff [HW] Enable early USB BIOS -> OS handoff
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
......
......@@ -23,33 +23,6 @@
#include <linux/acpi.h>
/*
* PIIX3 USB: We have to disable USB interrupts that are
* hardwired to PIRQD# and may be shared with an
* external device.
*
* Legacy Support Register (LEGSUP):
* bit13: USB PIRQ Enable (USBPIRQDEN),
* bit4: Trap/SMI On IRQ Enable (USBSMIEN).
*
* We mask out all r/wc bits, too.
*/
static void __devinit quirk_piix3_usb(struct pci_dev *dev)
{
u16 legsup;
pci_read_config_word(dev, 0xc0, &legsup);
legsup &= 0x50ef;
pci_write_config_word(dev, 0xc0, legsup);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_2, quirk_piix3_usb );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_2, quirk_piix3_usb );
/* FIXME these should be the guts of hcd->reset() methods; resolve all
* the differences between this version and the HCD's version.
*/
#define UHCI_USBLEGSUP 0xc0 /* legacy support */
#define UHCI_USBCMD 0 /* command register */
#define UHCI_USBINTR 4 /* interrupt register */
......@@ -83,13 +56,6 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_2, qui
#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI on ownership change */
int usb_early_handoff __devinitdata = 0;
static int __init usb_handoff_early(char *str)
{
usb_early_handoff = 1;
return 0;
}
__setup("usb-handoff", usb_handoff_early);
/*
* Make sure the controller is completely inactive, unable to
......@@ -320,17 +286,11 @@ static void __devinit quirk_usb_disable_ehci(struct pci_dev *pdev)
static void __devinit quirk_usb_early_handoff(struct pci_dev *pdev)
{
if (!usb_early_handoff)
return;
if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x00)) { /* UHCI */
if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
quirk_usb_handoff_uhci(pdev);
} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x10)) { /* OHCI */
else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
quirk_usb_handoff_ohci(pdev);
} else if (pdev->class == ((PCI_CLASS_SERIAL_USB << 8) | 0x20)) { /* EHCI */
else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
quirk_usb_disable_ehci(pdev);
}
return;
}
DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, quirk_usb_early_handoff);
......@@ -22,7 +22,6 @@ static inline void mpc_oem_pci_bus(struct mpc_config_bus *m,
{
}
extern int usb_early_handoff;
static inline int mps_oem_check(struct mp_config_table *mpc, char *oem,
char *productid)
{
......@@ -32,7 +31,6 @@ static inline int mps_oem_check(struct mp_config_table *mpc, char *oem,
|| !strncmp(productid, "RUTHLESS SMP", 12))){
use_cyclone = 1; /*enable cyclone-timer*/
setup_summit();
usb_early_handoff = 1;
return 1;
}
return 0;
......@@ -46,7 +44,6 @@ static inline int acpi_madt_oem_check(char *oem_id, char *oem_table_id)
|| !strncmp(oem_table_id, "EXA", 3))){
use_cyclone = 1; /*enable cyclone-timer*/
setup_summit();
usb_early_handoff = 1;
return 1;
}
return 0;
......
......@@ -96,6 +96,9 @@
#define PCI_CLASS_SERIAL_ACCESS 0x0c01
#define PCI_CLASS_SERIAL_SSA 0x0c02
#define PCI_CLASS_SERIAL_USB 0x0c03
#define PCI_CLASS_SERIAL_USB_UHCI 0x0c0300
#define PCI_CLASS_SERIAL_USB_OHCI 0x0c0310
#define PCI_CLASS_SERIAL_USB_EHCI 0x0c0320
#define PCI_CLASS_SERIAL_FIBER 0x0c04
#define PCI_CLASS_SERIAL_SMBUS 0x0c05
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册