Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (249 commits)
  powerpc: Fix pte_update for CONFIG_PTE_64BIT and !PTE_ATOMIC_UPDATES
  powerpc: Fix a build problem on ppc32 with new DMA_ATTRs
  ibm_newemac: Add MII mode support to the EMAC RGMII bridge.
  powerpc: Don't spin on sync instruction at boot time
  powerpc: Add VSX load/store alignment exception handler
  powerpc: fix giveup_vsx to save registers correctly
  powerpc: support for latencytop
  powerpc: Remove unnecessary condition when sanity-checking WIMG bits
  powerpc: Add PPC_FEATURE_PSERIES_PERFMON_COMPAT
  powerpc: Add driver for Barrier Synchronization Register
  powerpc: mman.h export fixups
  powerpc/fsl: update crypto node definition and device tree instances
  powerpc/fsl: Refactor device bindings
  powerpc/85xx: Minor fixes for 85xxds and 8536ds board.
  powerpc: Add 82xx/83xx/86xx to 6xx Multiplatform
  powerpc/85xx: publish of device for cds platforms
  powerpc/booke: don't reinitialize time base
  powerpc/86xx: Refactor pic init
  powerpc/CPM: Add i2c pins to dts and board setup
  cpm_uart: Support uart_wait_until_sent()
  ...

Documentation/kprobes.txt

@@ -172,6 +172,7 @@ architectures:
 - ia64 (Does not support probes on instruction slot1.)
 - sparc64 (Return probes not yet implemented.)
 - arm
+- ppc
 
 3. Configuring Kprobes
 

Documentation/powerpc/bootwrapper.txt

+The PowerPC boot wrapper
+------------------------
+Copyright (C) Secret Lab Technologies Ltd.
+
+PowerPC image targets compresses and wraps the kernel image (vmlinux) with
+a boot wrapper to make it usable by the system firmware.  There is no
+standard PowerPC firmware interface, so the boot wrapper is designed to
+be adaptable for each kind of image that needs to be built.
+
+The boot wrapper can be found in the arch/powerpc/boot/ directory.  The
+Makefile in that directory has targets for all the available image types.
+The different image types are used to support all of the various firmware
+interfaces found on PowerPC platforms.  OpenFirmware is the most commonly
+used firmware type on general purpose PowerPC systems from Apple, IBM and
+others.  U-Boot is typically found on embedded PowerPC hardware, but there
+are a handful of other firmware implementations which are also popular.  Each
+firmware interface requires a different image format.
+
+The boot wrapper is built from the makefile in arch/powerpc/boot/Makefile and
+it uses the wrapper script (arch/powerpc/boot/wrapper) to generate target
+image.  The details of the build system is discussed in the next section.
+Currently, the following image format targets exist:
+
+   cuImage.%:		Backwards compatible uImage for older version of
+			U-Boot (for versions that don't understand the device
+			tree).  This image embeds a device tree blob inside
+			the image.  The boot wrapper, kernel and device tree
+			are all embedded inside the U-Boot uImage file format
+			with boot wrapper code that extracts data from the old
+			bd_info structure and loads the data into the device
+			tree before jumping into the kernel.
+			  Because of the series of #ifdefs found in the
+			bd_info structure used in the old U-Boot interfaces,
+			cuImages are platform specific.  Each specific
+			U-Boot platform has a different platform init file
+			which populates the embedded device tree with data
+			from the platform specific bd_info file.  The platform
+			specific cuImage platform init code can be found in
+			arch/powerpc/boot/cuboot.*.c.  Selection of the correct
+			cuImage init code for a specific board can be found in
+			the wrapper structure.
+   dtbImage.%:		Similar to zImage, except device tree blob is embedded
+			inside the image instead of provided by firmware.  The
+			output image file can be either an elf file or a flat
+			binary depending on the platform.
+			  dtbImages are used on systems which do not have an
+			interface for passing a device tree directly.
+			dtbImages are similar to simpleImages except that
+			dtbImages have platform specific code for extracting
+			data from the board firmware, but simpleImages do not
+			talk to the firmware at all.
+			  PlayStation 3 support uses dtbImage.  So do Embedded
+			Planet boards using the PlanetCore firmware.  Board
+			specific initialization code is typically found in a
+			file named arch/powerpc/boot/<platform>.c; but this
+			can be overridden by the wrapper script.
+   simpleImage.%:	Firmware independent compressed image that does not
+			depend on any particular firmware interface and embeds
+			a device tree blob.  This image is a flat binary that
+			can be loaded to any location in RAM and jumped to.
+			Firmware cannot pass any configuration data to the
+			kernel with this image type and it depends entirely on
+			the embedded device tree for all information.
+			  The simpleImage is useful for booting systems with
+			an unknown firmware interface or for booting from
+			a debugger when no firmware is present (such as on
+			the Xilinx Virtex platform).  The only assumption that
+			simpleImage makes is that RAM is correctly initialized
+			and that the MMU is either off or has RAM mapped to
+			base address 0.
+			  simpleImage also supports inserting special platform
+			specific initialization code to the start of the bootup
+			sequence.  The virtex405 platform uses this feature to
+			ensure that the cache is invalidated before caching
+			is enabled.  Platform specific initialization code is
+			added as part of the wrapper script and is keyed on
+			the image target name.  For example, all
+			simpleImage.virtex405-* targets will add the
+			virtex405-head.S initialization code (This also means
+			that the dts file for virtex405 targets should be
+			named (virtex405-<board>.dts).  Search the wrapper
+			script for 'virtex405' and see the file
+			arch/powerpc/boot/virtex405-head.S for details.
+   treeImage.%;		Image format for used with OpenBIOS firmware found
+			on some ppc4xx hardware.  This image embeds a device
+			tree blob inside the image.
+   uImage:		Native image format used by U-Boot.  The uImage target
+			does not add any boot code.  It just wraps a compressed
+			vmlinux in the uImage data structure.  This image
+			requires a version of U-Boot that is able to pass
+			a device tree to the kernel at boot.  If using an older
+			version of U-Boot, then you need to use a cuImage
+			instead.
+   zImage.%:		Image format which does not embed a device tree.
+			Used by OpenFirmware and other firmware interfaces
+			which are able to supply a device tree.  This image
+			expects firmware to provide the device tree at boot.
+			Typically, if you have general purpose PowerPC
+			hardware then you want this image format.
+
+Image types which embed a device tree blob (simpleImage, dtbImage, treeImage,
+and cuImage) all generate the device tree blob from a file in the
+arch/powerpc/boot/dts/ directory.  The Makefile selects the correct device
+tree source based on the name of the target.  Therefore, if the kernel is
+built with 'make treeImage.walnut simpleImage.virtex405-ml403', then the
+build system will use arch/powerpc/boot/dts/walnut.dts to build
+treeImage.walnut and arch/powerpc/boot/dts/virtex405-ml403.dts to build
+the simpleImage.virtex405-ml403.
+
+Two special targets called 'zImage' and 'zImage.initrd' also exist.  These
+targets build all the default images as selected by the kernel configuration.
+Default images are selected by the boot wrapper Makefile
+(arch/powerpc/boot/Makefile) by adding targets to the $image-y variable.  Look
+at the Makefile to see which default image targets are available.
+
+How it is built
+---------------
+arch/powerpc is designed to support multiplatform kernels, which means
+that a single vmlinux image can be booted on many different target boards.
+It also means that the boot wrapper must be able to wrap for many kinds of
+images on a single build.  The design decision was made to not use any
+conditional compilation code (#ifdef, etc) in the boot wrapper source code.
+All of the boot wrapper pieces are buildable at any time regardless of the
+kernel configuration.  Building all the wrapper bits on every kernel build
+also ensures that obscure parts of the wrapper are at the very least compile
+tested in a large variety of environments.
+
+The wrapper is adapted for different image types at link time by linking in
+just the wrapper bits that are appropriate for the image type.  The 'wrapper
+script' (found in arch/powerpc/boot/wrapper) is called by the Makefile and
+is responsible for selecting the correct wrapper bits for the image type.
+The arguments are well documented in the script's comment block, so they
+are not repeated here.  However, it is worth mentioning that the script
+uses the -p (platform) argument as the main method of deciding which wrapper
+bits to compile in.  Look for the large 'case "$platform" in' block in the
+middle of the script.  This is also the place where platform specific fixups
+can be selected by changing the link order.
+
+In particular, care should be taken when working with cuImages.  cuImage
+wrapper bits are very board specific and care should be taken to make sure
+the target you are trying to build is supported by the wrapper bits.

Documentation/powerpc/dts-bindings/fsl/board.txt

+* Board Control and Status (BCSR)
+
+Required properties:
+
+ - device_type : Should be "board-control"
+ - reg : Offset and length of the register set for the device
+
+Example:
+
+	bcsr@f8000000 {
+		device_type = "board-control";
+		reg = <f8000000 8000>;
+	};
+
+* Freescale on board FPGA
+
+This is the memory-mapped registers for on board FPGA.
+
+Required properities:
+- compatible : should be "fsl,fpga-pixis".
+- reg : should contain the address and the lenght of the FPPGA register
+  set.
+
+Example (MPC8610HPCD):
+
+	board-control@e8000000 {
+		compatible = "fsl,fpga-pixis";
+		reg = <0xe8000000 32>;
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm.txt

+* Freescale Communications Processor Module
+
+NOTE: This is an interim binding, and will likely change slightly,
+as more devices are supported.  The QE bindings especially are
+incomplete.
+
+* Root CPM node
+
+Properties:
+- compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
+- reg : A 48-byte region beginning with CPCR.
+
+Example:
+     cpm@119c0 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	#interrupt-cells = <2>;
+	compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
+	reg = <119c0 30>;
+     }
+
+* Properties common to mulitple CPM/QE devices
+
+- fsl,cpm-command : This value is ORed with the opcode and command flag
+                    to specify the device on which a CPM command operates.
+
+- fsl,cpm-brg : Indicates which baud rate generator the device
+                is associated with.  If absent, an unused BRG
+                should be dynamically allocated.  If zero, the
+                device uses an external clock rather than a BRG.
+
+- reg : Unless otherwise specified, the first resource represents the
+        scc/fcc/ucc registers, and the second represents the device's
+        parameter RAM region (if it has one).
+
+* Multi-User RAM (MURAM)
+
+The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
+
+Ranges must be set up subject to the following restrictions:
+
+- Children's reg nodes must be offsets from the start of all muram, even
+  if the user-data area does not begin at zero.
+- If multiple range entries are used, the difference between the parent
+  address and the child address must be the same in all, so that a single
+  mapping can cover them all while maintaining the ability to determine
+  CPM-side offsets with pointer subtraction.  It is recommended that
+  multiple range entries not be used.
+- A child address of zero must be translatable, even if no reg resources
+  contain it.
+
+A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
+indicate the portion of muram that is usable by the OS for arbitrary
+purposes.  The data node may have an arbitrary number of reg resources,
+all of which contribute to the allocatable muram pool.
+
+Example, based on mpc8272:
+	muram@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 10000>;
+
+		data@0 {
+			compatible = "fsl,cpm-muram-data";
+			reg = <0 2000 9800 800>;
+		};
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/brg.txt

+* Baud Rate Generators
+
+Currently defined compatibles:
+fsl,cpm-brg
+fsl,cpm1-brg
+fsl,cpm2-brg
+
+Properties:
+- reg : There may be an arbitrary number of reg resources; BRG
+  numbers are assigned to these in order.
+- clock-frequency : Specifies the base frequency driving
+  the BRG.
+
+Example:
+	brg@119f0 {
+		compatible = "fsl,mpc8272-brg",
+			     "fsl,cpm2-brg",
+			     "fsl,cpm-brg";
+		reg = <119f0 10 115f0 10>;
+		clock-frequency = <d#25000000>;
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/i2c.txt

+* I2C
+
+The I2C controller is expressed as a bus under the CPM node.
+
+Properties:
+- compatible : "fsl,cpm1-i2c", "fsl,cpm2-i2c"
+- reg : On CPM2 devices, the second resource doesn't specify the I2C
+  Parameter RAM itself, but the I2C_BASE field of the CPM2 Parameter RAM
+  (typically 0x8afc 0x2).
+- #address-cells : Should be one. The cell is the i2c device address with
+  the r/w bit set to zero.
+- #size-cells : Should be zero.
+- clock-frequency : Can be used to set the i2c clock frequency. If
+  unspecified, a default frequency of 60kHz is being used.
+The following two properties are deprecated. They are only used by legacy
+i2c drivers to find the bus to probe:
+- linux,i2c-index : Can be used to hard code an i2c bus number. By default,
+  the bus number is dynamically assigned by the i2c core.
+- linux,i2c-class : Can be used to override the i2c class. The class is used
+  by legacy i2c device drivers to find a bus in a specific context like
+  system management, video or sound. By default, I2C_CLASS_HWMON (1) is
+  being used. The definition of the classes can be found in
+  include/i2c/i2c.h
+
+Example, based on mpc823:
+
+	i2c@860 {
+		compatible = "fsl,mpc823-i2c",
+			     "fsl,cpm1-i2c";
+		reg = <0x860 0x20 0x3c80 0x30>;
+		interrupts = <16>;
+		interrupt-parent = <&CPM_PIC>;
+		fsl,cpm-command = <0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@68 {
+			compatible = "dallas,ds1307";
+			reg = <0x68>;
+		};
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/pic.txt

+* Interrupt Controllers
+
+Currently defined compatibles:
+- fsl,cpm1-pic
+  - only one interrupt cell
+- fsl,pq1-pic
+- fsl,cpm2-pic
+  - second interrupt cell is level/sense:
+    - 2 is falling edge
+    - 8 is active low
+
+Example:
+	interrupt-controller@10c00 {
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <10c00 80>;
+		compatible = "mpc8272-pic", "fsl,cpm2-pic";
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/cpm/usb.txt

+* USB (Universal Serial Bus Controller)
+
+Properties:
+- compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
+
+Example:
+	usb@11bc0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,cpm2-usb";
+		reg = <11b60 18 8b00 100>;
+		interrupts = <b 8>;
+		interrupt-parent = <&PIC>;
+		fsl,cpm-command = <2e600000>;
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/network.txt

+* Network
+
+Currently defined compatibles:
+- fsl,cpm1-scc-enet
+- fsl,cpm2-scc-enet
+- fsl,cpm1-fec-enet
+- fsl,cpm2-fcc-enet (third resource is GFEMR)
+- fsl,qe-enet
+
+Example:
+
+	ethernet@11300 {
+		device_type = "network";
+		compatible = "fsl,mpc8272-fcc-enet",
+			     "fsl,cpm2-fcc-enet";
+		reg = <11300 20 8400 100 11390 1>;
+		local-mac-address = [ 00 00 00 00 00 00 ];
+		interrupts = <20 8>;
+		interrupt-parent = <&PIC>;
+		phy-handle = <&PHY0>;
+		fsl,cpm-command = <12000300>;
+	};
+
+* MDIO
+
+Currently defined compatibles:
+fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
+fsl,cpm2-mdio-bitbang (reg is port C registers)
+
+Properties for fsl,cpm2-mdio-bitbang:
+fsl,mdio-pin : pin of port C controlling mdio data
+fsl,mdc-pin : pin of port C controlling mdio clock
+
+Example:
+	mdio@10d40 {
+		device_type = "mdio";
+		compatible = "fsl,mpc8272ads-mdio-bitbang",
+			     "fsl,mpc8272-mdio-bitbang",
+			     "fsl,cpm2-mdio-bitbang";
+		reg = <10d40 14>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		fsl,mdio-pin = <12>;
+		fsl,mdc-pin = <13>;
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe.txt

+* Freescale QUICC Engine module (QE)
+This represents qe module that is installed on PowerQUICC II Pro.
+
+NOTE:  This is an interim binding; it should be updated to fit
+in with the CPM binding later in this document.
+
+Basically, it is a bus of devices, that could act more or less
+as a complete entity (UCC, USB etc ). All of them should be siblings on
+the "root" qe node, using the common properties from there.
+The description below applies to the qe of MPC8360 and
+more nodes and properties would be extended in the future.
+
+i) Root QE device
+
+Required properties:
+- compatible : should be "fsl,qe";
+- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
+- reg : offset and length of the device registers.
+- bus-frequency : the clock frequency for QUICC Engine.
+
+Recommended properties
+- brg-frequency : the internal clock source frequency for baud-rate
+  generators in Hz.
+
+Example:
+     qe@e0100000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	#interrupt-cells = <2>;
+	compatible = "fsl,qe";
+	ranges = <0 e0100000 00100000>;
+	reg = <e0100000 480>;
+	brg-frequency = <0>;
+	bus-frequency = <179A7B00>;
+     }
+
+* Multi-User RAM (MURAM)
+
+Required properties:
+- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
+- mode : the could be "host" or "slave".
+- ranges : Should be defined as specified in 1) to describe the
+   translation of MURAM addresses.
+- data-only : sub-node which defines the address area under MURAM
+   bus that can be allocated as data/parameter
+
+Example:
+
+     muram@10000 {
+	compatible = "fsl,qe-muram", "fsl,cpm-muram";
+	ranges = <0 00010000 0000c000>;
+
+	data-only@0{
+		compatible = "fsl,qe-muram-data",
+			     "fsl,cpm-muram-data";
+		reg = <0 c000>;
+	};
+     };

Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/firmware.txt

+* Uploaded QE firmware
+
+      If a new firwmare has been uploaded to the QE (usually by the
+      boot loader), then a 'firmware' child node should be added to the QE
+      node.  This node provides information on the uploaded firmware that
+      device drivers may need.
+
+      Required properties:
+      - id: The string name of the firmware.  This is taken from the 'id'
+            member of the qe_firmware structure of the uploaded firmware.
+            Device drivers can search this string to determine if the
+            firmware they want is already present.
+      - extended-modes: The Extended Modes bitfield, taken from the
+		   firmware binary.  It is a 64-bit number represented
+		   as an array of two 32-bit numbers.
+      - virtual-traps: The virtual traps, taken from the firmware binary.
+		  It is an array of 8 32-bit numbers.
+
+Example:
+	firmware {
+		id = "Soft-UART";
+		extended-modes = <0 0>;
+		virtual-traps = <0 0 0 0 0 0 0 0>;
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/par_io.txt

+* Parallel I/O Ports
+
+This node configures Parallel I/O ports for CPUs with QE support.
+The node should reside in the "soc" node of the tree.  For each
+device that using parallel I/O ports, a child node should be created.
+See the definition of the Pin configuration nodes below for more
+information.
+
+Required properties:
+- device_type : should be "par_io".
+- reg : offset to the register set and its length.
+- num-ports : number of Parallel I/O ports
+
+Example:
+par_io@1400 {
+	reg = <1400 100>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	device_type = "par_io";
+	num-ports = <7>;
+	ucc_pin@01 {
+		......
+	};
+
+Note that "par_io" nodes are obsolete, and should not be used for
+the new device trees. Instead, each Par I/O bank should be represented
+via its own gpio-controller node:
+
+Required properties:
+- #gpio-cells : should be "2".
+- compatible : should be "fsl,<chip>-qe-pario-bank",
+  "fsl,mpc8323-qe-pario-bank".
+- reg : offset to the register set and its length.
+- gpio-controller : node to identify gpio controllers.
+
+Example:
+	qe_pio_a: gpio-controller@1400 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8360-qe-pario-bank",
+		"fsl,mpc8323-qe-pario-bank";
+		reg = <0x1400 0x18>;
+		gpio-controller;
+	  };
+
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8360-qe-pario-bank",
+			     "fsl,mpc8323-qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+	  };

Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/pincfg.txt

+* Pin configuration nodes
+
+Required properties:
+- linux,phandle : phandle of this node; likely referenced by a QE
+  device.
+- pio-map : array of pin configurations.  Each pin is defined by 6
+  integers.  The six numbers are respectively: port, pin, dir,
+  open_drain, assignment, has_irq.
+  - port : port number of the pin; 0-6 represent port A-G in UM.
+  - pin : pin number in the port.
+  - dir : direction of the pin, should encode as follows:
+
+     0 = The pin is disabled
+     1 = The pin is an output
+     2 = The pin is an input
+     3 = The pin is I/O
+
+  - open_drain : indicates the pin is normal or wired-OR:
+
+     0 = The pin is actively driven as an output
+     1 = The pin is an open-drain driver. As an output, the pin is
+         driven active-low, otherwise it is three-stated.
+
+  - assignment : function number of the pin according to the Pin Assignment
+    tables in User Manual.  Each pin can have up to 4 possible functions in
+    QE and two options for CPM.
+  - has_irq : indicates if the pin is used as source of external
+    interrupts.
+
+Example:
+     ucc_pin@01 {
+	linux,phandle = <140001>;
+	pio-map = <
+	/* port  pin  dir  open_drain  assignment  has_irq */
+		0  3  1  0  1  0 	/* TxD0 */
+		0  4  1  0  1  0 	/* TxD1 */
+		0  5  1  0  1  0 	/* TxD2 */
+		0  6  1  0  1  0 	/* TxD3 */
+		1  6  1  0  3  0 	/* TxD4 */
+		1  7  1  0  1  0 	/* TxD5 */
+		1  9  1  0  2  0 	/* TxD6 */
+		1  a  1  0  2  0 	/* TxD7 */
+		0  9  2  0  1  0 	/* RxD0 */
+		0  a  2  0  1  0 	/* RxD1 */
+		0  b  2  0  1  0 	/* RxD2 */
+		0  c  2  0  1  0 	/* RxD3 */
+		0  d  2  0  1  0 	/* RxD4 */
+		1  1  2  0  2  0 	/* RxD5 */
+		1  0  2  0  2  0 	/* RxD6 */
+		1  4  2  0  2  0 	/* RxD7 */
+		0  7  1  0  1  0 	/* TX_EN */
+		0  8  1  0  1  0 	/* TX_ER */
+		0  f  2  0  1  0 	/* RX_DV */
+		0  10 2  0  1  0 	/* RX_ER */
+		0  0  2  0  1  0 	/* RX_CLK */
+		2  9  1  0  3  0 	/* GTX_CLK - CLK10 */
+		2  8  2  0  1  0>;	/* GTX125 - CLK9 */
+     };
+
+

Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt

+* UCC (Unified Communications Controllers)
+
+Required properties:
+- device_type : should be "network", "hldc", "uart", "transparent"
+  "bisync", "atm", or "serial".
+- compatible : could be "ucc_geth" or "fsl_atm" and so on.
+- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+  field that represents an encoding of the sense and level
+  information for the interrupt.  This should be encoded based on
+  the information in section 2) depending on the type of interrupt
+  controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+- pio-handle : The phandle for the Parallel I/O port configuration.
+- port-number : for UART drivers, the port number to use, between 0 and 3.
+  This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
+  The port number is added to the minor number of the device.  Unlike the
+  CPM UART driver, the port-number is required for the QE UART driver.
+- soft-uart : for UART drivers, if specified this means the QE UART device
+  driver should use "Soft-UART" mode, which is needed on some SOCs that have
+  broken UART hardware.  Soft-UART is provided via a microcode upload.
+- rx-clock-name: the UCC receive clock source
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+- tx-clock-name: the UCC transmit clock source
+  "none": clock source is disabled
+  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
+  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
+The following two properties are deprecated.  rx-clock has been replaced
+with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
+Drivers that currently use the deprecated properties should continue to
+do so, in order to support older device trees, but they should be updated
+to check for the new properties first.
+- rx-clock : represents the UCC receive clock source.
+  0x00 : clock source is disabled;
+  0x1~0x10 : clock source is BRG1~BRG16 respectively;
+  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+- tx-clock: represents the UCC transmit clock source;
+  0x00 : clock source is disabled;
+  0x1~0x10 : clock source is BRG1~BRG16 respectively;
+  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
+
+Required properties for network device_type:
+- mac-address : list of bytes representing the ethernet address.
+- phy-handle : The phandle for the PHY connected to this controller.
+
+Recommended properties:
+- phy-connection-type : a string naming the controller/PHY interface type,
+  i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+  Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+  "tbi", or "rtbi".
+
+Example:
+	ucc@2000 {
+		device_type = "network";
+		compatible = "ucc_geth";
+		cell-index = <1>;
+		reg = <2000 200>;
+		interrupts = <a0 0>;
+		interrupt-parent = <700>;
+		mac-address = [ 00 04 9f 00 23 23 ];
+		rx-clock = "none";
+		tx-clock = "clk9";
+		phy-handle = <212000>;
+		phy-connection-type = "gmii";
+		pio-handle = <140001>;
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/usb.txt

+* USB (Universal Serial Bus Controller)
+
+Required properties:
+- compatible : could be "qe_udc" or "fhci-hcd".
+- mode : the could be "host" or "slave".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+  field that represents an encoding of the sense and level
+  information for the interrupt.  This should be encoded based on
+  the information in section 2) depending on the type of interrupt
+  controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+
+Example(slave):
+	usb@6c0 {
+		compatible = "qe_udc";
+		reg = <6c0 40>;
+		interrupts = <8b 0>;
+		interrupt-parent = <700>;
+		mode = "slave";
+	};

Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt

+* Serial
+
+Currently defined compatibles:
+- fsl,cpm1-smc-uart
+- fsl,cpm2-smc-uart
+- fsl,cpm1-scc-uart
+- fsl,cpm2-scc-uart
+- fsl,qe-uart
+
+Example:
+
+	serial@11a00 {
+		device_type = "serial";
+		compatible = "fsl,mpc8272-scc-uart",
+			     "fsl,cpm2-scc-uart";
+		reg = <11a00 20 8000 100>;
+		interrupts = <28 8>;
+		interrupt-parent = <&PIC>;
+		fsl,cpm-brg = <1>;
+		fsl,cpm-command = <00800000>;
+	};

Documentation/powerpc/dts-bindings/fsl/diu.txt

+* Freescale Display Interface Unit
+
+The Freescale DIU is a LCD controller, with proper hardware, it can also
+drive DVI monitors.
+
+Required properties:
+- compatible : should be "fsl-diu".
+- reg : should contain at least address and length of the DIU register
+  set.
+- Interrupts : one DIU interrupt should be describe here.
+
+Example (MPC8610HPCD):
+	display@2c000 {
+		compatible = "fsl,diu";
+		reg = <0x2c000 100>;
+		interrupts = <72 2>;
+		interrupt-parent = <&mpic>;
+	};

Documentation/powerpc/dts-bindings/fsl/dma.txt

+* Freescale 83xx DMA Controller
+
+Freescale PowerPC 83xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible        : compatible list, contains 2 entries, first is
+		 "fsl,CHIP-dma", where CHIP is the processor
+		 (mpc8349, mpc8360, etc.) and the second is
+		 "fsl,elo-dma"
+- reg               : <registers mapping for DMA general status reg>
+- ranges		: Should be defined as specified in 1) to describe the
+		  DMA controller channels.
+- cell-index        : controller index.  0 for controller @ 0x8100
+- interrupts        : <interrupt mapping for DMA IRQ>
+- interrupt-parent  : optional, if needed for interrupt mapping
+
+
+- DMA channel nodes:
+        - compatible        : compatible list, contains 2 entries, first is
+			 "fsl,CHIP-dma-channel", where CHIP is the processor
+			 (mpc8349, mpc8350, etc.) and the second is
+			 "fsl,elo-dma-channel"
+        - reg               : <registers mapping for channel>
+        - cell-index        : dma channel index starts at 0.
+
+Optional properties:
+        - interrupts        : <interrupt mapping for DMA channel IRQ>
+			  (on 83xx this is expected to be identical to
+			   the interrupts property of the parent node)
+        - interrupt-parent  : optional, if needed for interrupt mapping
+
+Example:
+	dma@82a8 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
+		reg = <82a8 4>;
+		ranges = <0 8100 1a4>;
+		interrupt-parent = <&ipic>;
+		interrupts = <47 8>;
+		cell-index = <0>;
+		dma-channel@0 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <0>;
+			reg = <0 80>;
+		};
+		dma-channel@80 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <1>;
+			reg = <80 80>;
+		};
+		dma-channel@100 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <2>;
+			reg = <100 80>;
+		};
+		dma-channel@180 {
+			compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
+			cell-index = <3>;
+			reg = <180 80>;
+		};
+	};
+
+* Freescale 85xx/86xx DMA Controller
+
+Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
+
+Required properties:
+
+- compatible        : compatible list, contains 2 entries, first is
+		 "fsl,CHIP-dma", where CHIP is the processor
+		 (mpc8540, mpc8540, etc.) and the second is
+		 "fsl,eloplus-dma"
+- reg               : <registers mapping for DMA general status reg>
+- cell-index        : controller index.  0 for controller @ 0x21000,
+                                         1 for controller @ 0xc000
+- ranges		: Should be defined as specified in 1) to describe the
+		  DMA controller channels.
+
+- DMA channel nodes:
+        - compatible        : compatible list, contains 2 entries, first is
+			 "fsl,CHIP-dma-channel", where CHIP is the processor
+			 (mpc8540, mpc8560, etc.) and the second is
+			 "fsl,eloplus-dma-channel"
+        - cell-index        : dma channel index starts at 0.
+        - reg               : <registers mapping for channel>
+        - interrupts        : <interrupt mapping for DMA channel IRQ>
+        - interrupt-parent  : optional, if needed for interrupt mapping
+
+Example:
+	dma@21300 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
+		reg = <21300 4>;
+		ranges = <0 21100 200>;
+		cell-index = <0>;
+		dma-channel@0 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <0 80>;
+			cell-index = <0>;
+			interrupt-parent = <&mpic>;
+			interrupts = <14 2>;
+		};
+		dma-channel@80 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <80 80>;
+			cell-index = <1>;
+			interrupt-parent = <&mpic>;
+			interrupts = <15 2>;
+		};
+		dma-channel@100 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <100 80>;
+			cell-index = <2>;
+			interrupt-parent = <&mpic>;
+			interrupts = <16 2>;
+		};
+		dma-channel@180 {
+			compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
+			reg = <180 80>;
+			cell-index = <3>;
+			interrupt-parent = <&mpic>;
+			interrupts = <17 2>;
+		};
+	};

Documentation/powerpc/dts-bindings/fsl/gtm.txt

+* Freescale General-purpose Timers Module
+
+Required properties:
+  - compatible : should be
+    "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
+    "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
+    "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
+  - reg : should contain gtm registers location and length (0x40).
+  - interrupts : should contain four interrupts.
+  - interrupt-parent : interrupt source phandle.
+  - clock-frequency : specifies the frequency driving the timer.
+
+Example:
+
+timer@500 {
+	compatible = "fsl,mpc8360-gtm", "fsl,gtm";
+	reg = <0x500 0x40>;
+	interrupts = <90 8 78 8 84 8 72 8>;
+	interrupt-parent = <&ipic>;
+	/* filled by u-boot */
+	clock-frequency = <0>;
+};
+
+timer@440 {
+	compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
+	reg = <0x440 0x40>;
+	interrupts = <12 13 14 15>;
+	interrupt-parent = <&qeic>;
+	/* filled by u-boot */
+	clock-frequency = <0>;
+};

Documentation/powerpc/dts-bindings/fsl/guts.txt

+* Global Utilities Block
+
+The global utilities block controls power management, I/O device
+enabling, power-on-reset configuration monitoring, general-purpose
+I/O signal configuration, alternate function selection for multiplexed
+signals, and clock control.
+
+Required properties:
+
+ - compatible : Should define the compatible device type for
+   global-utilities.
+ - reg : Offset and length of the register set for the device.
+
+Recommended properties:
+
+ - fsl,has-rstcr : Indicates that the global utilities register set
+   contains a functioning "reset control register" (i.e. the board
+   is wired to reset upon setting the HRESET_REQ bit in this register).
+
+Example:
+	global-utilities@e0000 {	/* global utilities block */
+		compatible = "fsl,mpc8548-guts";
+		reg = <e0000 1000>;
+		fsl,has-rstcr;
+	};

Documentation/powerpc/dts-bindings/fsl/i2c.txt

+* I2C
+
+Required properties :
+
+ - device_type : Should be "i2c"
+ - reg : Offset and length of the register set for the device
+
+Recommended properties :
+
+ - compatible : Should be "fsl-i2c" for parts compatible with
+   Freescale I2C specifications.
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device.
+ - dfsrr : boolean; if defined, indicates that this I2C device has
+   a digital filter sampling rate register
+ - fsl5200-clocking : boolean; if defined, indicated that this device
+   uses the FSL 5200 clocking mechanism.
+
+Example :
+	i2c@3000 {
+		interrupt-parent = <40000>;
+		interrupts = <1b 3>;
+		reg = <3000 18>;
+		device_type = "i2c";
+		compatible  = "fsl-i2c";
+		dfsrr;
+	};

Documentation/powerpc/dts-bindings/fsl/lbc.txt

+* Chipselect/Local Bus
+
+Properties:
+- name : Should be localbus
+- #address-cells : Should be either two or three.  The first cell is the
+                   chipselect number, and the remaining cells are the
+                   offset into the chipselect.
+- #size-cells : Either one or two, depending on how large each chipselect
+                can be.
+- ranges : Each range corresponds to a single chipselect, and cover
+           the entire access window as configured.
+
+Example:
+	localbus@f0010100 {
+		compatible = "fsl,mpc8272-localbus",
+			   "fsl,pq2-localbus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		reg = <f0010100 40>;
+
+		ranges = <0 0 fe000000 02000000
+			  1 0 f4500000 00008000>;
+
+		flash@0,0 {
+			compatible = "jedec-flash";
+			reg = <0 0 2000000>;
+			bank-width = <4>;
+			device-width = <1>;
+		};
+
+		board-control@1,0 {
+			reg = <1 0 20>;
+			compatible = "fsl,mpc8272ads-bcsr";
+		};
+	};

Documentation/powerpc/dts-bindings/fsl/msi-pic.txt

+* Freescale MSI interrupt controller
+
+Reguired properities:
+- compatible : compatible list, contains 2 entries,
+  first is "fsl,CHIP-msi", where CHIP is the processor(mpc8610, mpc8572,
+  etc.) and the second is "fsl,mpic-msi" or "fsl,ipic-msi" depending on
+  the parent type.
+- reg : should contain the address and the length of the shared message
+  interrupt register set.
+- msi-available-ranges: use <start count> style section to define which
+  msi interrupt can be used in the 256 msi interrupts. This property is
+  optional, without this, all the 256 MSI interrupts can be used.
+- interrupts : each one of the interrupts here is one entry per 32 MSIs,
+  and routed to the host interrupt controller. the interrupts should
+  be set as edge sensitive.
+- interrupt-parent: the phandle for the interrupt controller
+  that services interrupts for this device. for 83xx cpu, the interrupts
+  are routed to IPIC, and for 85xx/86xx cpu the interrupts are routed
+  to MPIC.
+
+Example:
+	msi@41600 {
+		compatible = "fsl,mpc8610-msi", "fsl,mpic-msi";
+		reg = <0x41600 0x80>;
+		msi-available-ranges = <0 0x100>;
+		interrupts = <
+			0xe0 0
+			0xe1 0
+			0xe2 0
+			0xe3 0
+			0xe4 0
+			0xe5 0
+			0xe6 0
+			0xe7 0>;
+		interrupt-parent = <&mpic>;
+	};

Documentation/powerpc/dts-bindings/fsl/sata.txt

+* Freescale 8xxx/3.0 Gb/s SATA nodes
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA port should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains 2 entries, first is
+		 "fsl,CHIP-sata", where CHIP is the processor
+		 (mpc8315, mpc8379, etc.) and the second is
+		 "fsl,pq-sata"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- cell-index        : controller index.
+                          1 for controller @ 0x18000
+                          2 for controller @ 0x19000
+                          3 for controller @ 0x1a000
+                          4 for controller @ 0x1b000
+
+Optional properties:
+- interrupt-parent  : optional, if needed for interrupt mapping
+- reg               : <registers mapping>
+
+Example:
+	sata@18000 {
+		compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
+		reg = <0x18000 0x1000>;
+		cell-index = <1>;
+		interrupts = <2c 8>;
+		interrupt-parent = < &ipic >;
+	};

Documentation/powerpc/dts-bindings/fsl/sec.txt

+Freescale SoC SEC Security Engines
+
+Required properties:
+
+- compatible : Should contain entries for this and backward compatible
+  SEC versions, high to low, e.g., "fsl,sec2.1", "fsl,sec2.0"
+- reg : Offset and length of the register set for the device
+- interrupts : the SEC's interrupt number
+- fsl,num-channels : An integer representing the number of channels
+  available.
+- fsl,channel-fifo-len : An integer representing the number of
+  descriptor pointers each channel fetch fifo can hold.
+- fsl,exec-units-mask : The bitmask representing what execution units
+  (EUs) are available. It's a single 32-bit cell. EU information
+  should be encoded following the SEC's Descriptor Header Dword
+  EU_SEL0 field documentation, i.e. as follows:
+
+	bit 0  = reserved - should be 0
+	bit 1  = set if SEC has the ARC4 EU (AFEU)
+	bit 2  = set if SEC has the DES/3DES EU (DEU)
+	bit 3  = set if SEC has the message digest EU (MDEU/MDEU-A)
+	bit 4  = set if SEC has the random number generator EU (RNG)
+	bit 5  = set if SEC has the public key EU (PKEU)
+	bit 6  = set if SEC has the AES EU (AESU)
+	bit 7  = set if SEC has the Kasumi EU (KEU)
+	bit 8  = set if SEC has the CRC EU (CRCU)
+	bit 11 = set if SEC has the message digest EU extended alg set (MDEU-B)
+
+remaining bits are reserved for future SEC EUs.
+
+- fsl,descriptor-types-mask : The bitmask representing what descriptors
+  are available. It's a single 32-bit cell. Descriptor type information
+  should be encoded following the SEC's Descriptor Header Dword DESC_TYPE
+  field documentation, i.e. as follows:
+
+	bit 0  = set if SEC supports the aesu_ctr_nonsnoop desc. type
+	bit 1  = set if SEC supports the ipsec_esp descriptor type
+	bit 2  = set if SEC supports the common_nonsnoop desc. type
+	bit 3  = set if SEC supports the 802.11i AES ccmp desc. type
+	bit 4  = set if SEC supports the hmac_snoop_no_afeu desc. type
+	bit 5  = set if SEC supports the srtp descriptor type
+	bit 6  = set if SEC supports the non_hmac_snoop_no_afeu desc.type
+	bit 7  = set if SEC supports the pkeu_assemble descriptor type
+	bit 8  = set if SEC supports the aesu_key_expand_output desc.type
+	bit 9  = set if SEC supports the pkeu_ptmul descriptor type
+	bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type
+	bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type
+
+  ..and so on and so forth.
+
+Optional properties:
+
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+
+Example:
+
+	/* MPC8548E */
+	crypto@30000 {
+		compatible = "fsl,sec2.1", "fsl,sec2.0";
+		reg = <0x30000 0x10000>;
+		interrupts = <29 2>;
+		interrupt-parent = <&mpic>;
+		fsl,num-channels = <4>;
+		fsl,channel-fifo-len = <24>;
+		fsl,exec-units-mask = <0xfe>;
+		fsl,descriptor-types-mask = <0x12b0ebf>;
+	};

Documentation/powerpc/dts-bindings/fsl/spi.txt

+* SPI (Serial Peripheral Interface)
+
+Required properties:
+- cell-index : SPI controller index.
+- compatible : should be "fsl,spi".
+- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
+- reg : Offset and length of the register set for the device
+- interrupts : <a b> where a is the interrupt number and b is a
+  field that represents an encoding of the sense and level
+  information for the interrupt.  This should be encoded based on
+  the information in section 2) depending on the type of interrupt
+  controller you have.
+- interrupt-parent : the phandle for the interrupt controller that
+  services interrupts for this device.
+
+Example:
+	spi@4c0 {
+		cell-index = <0>;
+		compatible = "fsl,spi";
+		reg = <4c0 40>;
+		interrupts = <82 0>;
+		interrupt-parent = <700>;
+		mode = "cpu";
+	};

Documentation/powerpc/dts-bindings/fsl/ssi.txt

+Freescale Synchronous Serial Interface
+
+The SSI is a serial device that communicates with audio codecs.  It can
+be programmed in AC97, I2S, left-justified, or right-justified modes.
+
+Required properties:
+- compatible	  : compatible list, containing "fsl,ssi"
+- cell-index	  : the SSI, <0> = SSI1, <1> = SSI2, and so on
+- reg		  : offset and length of the register set for the device
+- interrupts	  : <a b> where a is the interrupt number and b is a
+                     field that represents an encoding of the sense and
+		    level information for the interrupt.  This should be
+		    encoded based on the information in section 2)
+		    depending on the type of interrupt controller you
+		    have.
+- interrupt-parent : the phandle for the interrupt controller that
+                     services interrupts for this device.
+- fsl,mode	  : the operating mode for the SSI interface
+		    "i2s-slave" - I2S mode, SSI is clock slave
+		    "i2s-master" - I2S mode, SSI is clock master
+		    "lj-slave" - left-justified mode, SSI is clock slave
+		    "lj-master" - l.j. mode, SSI is clock master
+		    "rj-slave" - right-justified mode, SSI is clock slave
+		    "rj-master" - r.j., SSI is clock master
+		    "ac97-slave" - AC97 mode, SSI is clock slave
+		    "ac97-master" - AC97 mode, SSI is clock master
+
+Optional properties:
+- codec-handle	  : phandle to a 'codec' node that defines an audio
+		    codec connected to this SSI.  This node is typically
+		    a child of an I2C or other control node.
+
+Child 'codec' node required properties:
+- compatible	  : compatible list, contains the name of the codec
+
+Child 'codec' node optional properties:
+- clock-frequency  : The frequency of the input clock, which typically
+                     comes from an on-board dedicated oscillator.

Documentation/powerpc/dts-bindings/fsl/tsec.txt

+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected.  For each
+device that exists on this bus, a child node should be created.  See
+the definition of the PHY node below for an example of how to define
+a PHY.
+
+Required properties:
+  - reg : Offset and length of the register set for the device
+  - compatible : Should define the compatible device type for the
+    mdio.  Currently, this is most likely to be "fsl,gianfar-mdio"
+
+Example:
+
+	mdio@24520 {
+		reg = <24520 20>;
+		compatible = "fsl,gianfar-mdio";
+
+		ethernet-phy@0 {
+			......
+		};
+	};
+
+
+* Gianfar-compatible ethernet nodes
+
+Required properties:
+
+  - device_type : Should be "network"
+  - model : Model of the device.  Can be "TSEC", "eTSEC", or "FEC"
+  - compatible : Should be "gianfar"
+  - reg : Offset and length of the register set for the device
+  - mac-address : List of bytes representing the ethernet address of
+    this controller
+  - interrupts : <a b> where a is the interrupt number and b is a
+    field that represents an encoding of the sense and level
+    information for the interrupt.  This should be encoded based on
+    the information in section 2) depending on the type of interrupt
+    controller you have.
+  - interrupt-parent : the phandle for the interrupt controller that
+    services interrupts for this device.
+  - phy-handle : The phandle for the PHY connected to this ethernet
+    controller.
+  - fixed-link : <a b c d e> where a is emulated phy id - choose any,
+    but unique to the all specified fixed-links, b is duplex - 0 half,
+    1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
+    pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
+
+Recommended properties:
+
+  - phy-connection-type : a string naming the controller/PHY interface type,
+    i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
+    "tbi", or "rtbi".  This property is only really needed if the connection
+    is of type "rgmii-id", as all other connection types are detected by
+    hardware.
+
+
+Example:
+	ethernet@24000 {
+		#size-cells = <0>;
+		device_type = "network";
+		model = "TSEC";
+		compatible = "gianfar";
+		reg = <24000 1000>;
+		mac-address = [ 00 E0 0C 00 73 00 ];
+		interrupts = <d 3 e 3 12 3>;
+		interrupt-parent = <40000>;
+		phy-handle = <2452000>
+	};

Documentation/powerpc/dts-bindings/fsl/usb.txt

+Freescale SOC USB controllers
+
+The device node for a USB controller that is part of a Freescale
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "fsl-usb2-mph" for multi port host USB
+   controllers, or "fsl-usb2-dr" for dual role USB controllers
+ - phy_type : For multi port host USB controllers, should be one of
+   "ulpi", or "serial". For dual role USB controllers, should be
+   one of "ulpi", "utmi", "utmi_wide", or "serial".
+ - reg : Offset and length of the register set for the device
+ - port0 : boolean; if defined, indicates port0 is connected for
+   fsl-usb2-mph compatible controllers.  Either this property or
+   "port1" (or both) must be defined for "fsl-usb2-mph" compatible
+   controllers.
+ - port1 : boolean; if defined, indicates port1 is connected for
+   fsl-usb2-mph compatible controllers.  Either this property or
+   "port0" (or both) must be defined for "fsl-usb2-mph" compatible
+   controllers.
+ - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
+   controllers.  Can be "host", "peripheral", or "otg".  Default to
+   "host" if not defined for backward compatibility.
+
+Recommended properties :
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device.
+
+Example multi port host USB controller device node :
+	usb@22000 {
+		compatible = "fsl-usb2-mph";
+		reg = <22000 1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <700>;
+		interrupts = <27 1>;
+		phy_type = "ulpi";
+		port0;
+		port1;
+	};
+
+Example dual role USB controller device node :
+	usb@23000 {
+		compatible = "fsl-usb2-dr";
+		reg = <23000 1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <700>;
+		interrupts = <26 1>;
+		dr_mode = "otg";
+		phy = "ulpi";
+	};

MAINTAINERS

@@ -2521,13 +2521,11 @@ W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 
-LINUX FOR POWERPC EMBEDDED MPC52XX
+LINUX FOR POWERPC EMBEDDED MPC5XXX
 P:	Sylvain Munaut
 M:	tnt@246tNt.com
 P:	Grant Likely
 M:	grant.likely@secretlab.ca
-W:	http://www.246tNt.com/mpc52xx/
-W:	http://www.penguinppc.org/
 L:	linuxppc-dev@ozlabs.org
 S:	Maintained
 

Makefile

+FRED=42
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 26

arch/powerpc/Kconfig

@@ -53,6 +53,9 @@ config STACKTRACE_SUPPORT
 	bool
 	default y
 
+config HAVE_LATENCYTOP_SUPPORT
+	def_bool y
+
 config TRACE_IRQFLAGS_SUPPORT
 	bool
 	depends on PPC64
@@ -111,6 +114,7 @@ config PPC
 	select HAVE_KPROBES
 	select HAVE_KRETPROBES
 	select HAVE_LMB
+	select HAVE_DMA_ATTRS if PPC64
 	select USE_GENERIC_SMP_HELPERS if SMP
 	select HAVE_OPROFILE
 
@@ -311,8 +315,8 @@ config KEXEC
 	  strongly in flux, so no good recommendation can be made.
 
 config CRASH_DUMP
-	bool "Build a kdump crash kernel (EXPERIMENTAL)"
-	depends on PPC_MULTIPLATFORM && PPC64 && EXPERIMENTAL
+	bool "Build a kdump crash kernel"
+	depends on PPC_MULTIPLATFORM && PPC64
 	help
 	  Build a kernel suitable for use as a kdump capture kernel.
 	  The kernel will be linked at a different address than normal, and
@@ -461,6 +465,19 @@ config CMDLINE
 	  some command-line options at build time by entering them here.  In
 	  most cases you will need to specify the root device here.
 
+config EXTRA_TARGETS
+	string "Additional default image types"
+	help
+	  List additional targets to be built by the bootwrapper here (separated
+	  by spaces).  This is useful for targets that depend of device tree
+	  files in the .dts directory.
+
+	  Targets in this list will be build as part of the default build
+	  target, or when the user does a 'make zImage' or a
+	  'make zImage.initrd'.
+
+	  If unsure, leave blank
+
 if !44x || BROKEN
 config ARCH_WANTS_FREEZER_CONTROL
 	def_bool y
@@ -541,6 +558,12 @@ config FSL_LBC
 	help
 	  Freescale Localbus support
 
+config FSL_GTM
+	bool
+	depends on PPC_83xx || QUICC_ENGINE || CPM2
+	help
+	  Freescale General-purpose Timers support
+
 # Yes MCA RS/6000s exist but Linux-PPC does not currently support any
 config MCA
 	bool

arch/powerpc/Kconfig.debug

@@ -57,6 +57,16 @@ config KGDB
 	  debugger.  See <http://kgdb.sourceforge.net/> for more information.
 	  Unless you are intending to debug the kernel, say N here.
 
+config CODE_PATCHING_SELFTEST
+	bool "Run self-tests of the code-patching code."
+	depends on DEBUG_KERNEL
+	default n
+
+config FTR_FIXUP_SELFTEST
+	bool "Run self-tests of the feature-fixup code."
+	depends on DEBUG_KERNEL
+	default n
+
 choice
 	prompt "Serial Port"
 	depends on KGDB

arch/powerpc/Makefile

@@ -18,22 +18,16 @@ HAS_BIARCH	:= $(call cc-option-yn, -m32)
 CROSS32_COMPILE ?=
 
 CROSS32CC		:= $(CROSS32_COMPILE)gcc
-CROSS32AS		:= $(CROSS32_COMPILE)as
-CROSS32LD		:= $(CROSS32_COMPILE)ld
 CROSS32AR		:= $(CROSS32_COMPILE)ar
-CROSS32OBJCOPY		:= $(CROSS32_COMPILE)objcopy
 
 ifeq ($(HAS_BIARCH),y)
 ifeq ($(CROSS32_COMPILE),)
 CROSS32CC	:= $(CC) -m32
-CROSS32AS	:= $(AS) -a32
-CROSS32LD	:= $(LD) -m elf32ppc
-CROSS32OBJCOPY	:= $(OBJCOPY)
 CROSS32AR	:= GNUTARGET=elf32-powerpc $(AR)
 endif
 endif
 
-export CROSS32CC CROSS32AS CROSS32LD CROSS32AR CROSS32OBJCOPY
+export CROSS32CC CROSS32AR
 
 ifeq ($(CROSS_COMPILE),)
 KBUILD_DEFCONFIG := $(shell uname -m)_defconfig
@@ -169,12 +163,25 @@ bootwrapper_install %.dtb:
 	$(Q)$(MAKE) ARCH=ppc64 $(build)=$(boot) $(patsubst %,$(boot)/%,$@)
 
 define archhelp
-  @echo '* zImage          - Compressed kernel image (arch/$(ARCH)/boot/zImage.*)'
+  @echo '* zImage          - Build default images selected by kernel config'
+  @echo '  zImage.*        - Compressed kernel image (arch/$(ARCH)/boot/zImage.*)'
+  @echo '  uImage          - U-Boot native image format'
+  @echo '  cuImage.<dt>    - Backwards compatible U-Boot image for older'
+  @echo '                    versions which do not support device trees'
+  @echo '  dtbImage.<dt>   - zImage with an embedded device tree blob'
+  @echo '  simpleImage.<dt> - Firmware independent image.'
+  @echo '  treeImage.<dt>  - Support for older IBM 4xx firmware (not U-Boot)'
   @echo '  install         - Install kernel using'
   @echo '                    (your) ~/bin/installkernel or'
   @echo '                    (distribution) /sbin/installkernel or'
   @echo '                    install to $$(INSTALL_PATH) and run lilo'
   @echo '  *_defconfig     - Select default config from arch/$(ARCH)/configs'
+  @echo ''
+  @echo '  Targets with <dt> embed a device tree blob inside the image'
+  @echo '  These targets support board with firmware that does not'
+  @echo '  support passing a device tree directly.  Replace <dt> with the'
+  @echo '  name of a dts file from the arch/$(ARCH)/boot/dts/ directory'
+  @echo '  (minus the .dts extension).'
 endef
 
 install:

arch/powerpc/boot/Makefile

@@ -35,6 +35,8 @@ endif
 
 BOOTCFLAGS	+= -I$(obj) -I$(srctree)/$(obj) -I$(srctree)/$(src)/libfdt
 
+DTS_FLAGS	?= -p 1024
+
 $(obj)/4xx.o: BOOTCFLAGS += -mcpu=405
 $(obj)/ebony.o: BOOTCFLAGS += -mcpu=405
 $(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=405
@@ -63,10 +65,10 @@ src-plat := of.c cuboot-52xx.c cuboot-824x.c cuboot-83xx.c cuboot-85xx.c holly.c
 		ps3-head.S ps3-hvcall.S ps3.c treeboot-bamboo.c cuboot-8xx.c \
 		cuboot-pq2.c cuboot-sequoia.c treeboot-walnut.c \
 		cuboot-bamboo.c cuboot-mpc7448hpc2.c cuboot-taishan.c \
-		fixed-head.S ep88xc.c ep405.c \
+		fixed-head.S ep88xc.c ep405.c cuboot-c2k.c \
 		cuboot-katmai.c cuboot-rainier.c redboot-8xx.c ep8248e.c \
 		cuboot-warp.c cuboot-85xx-cpm2.c cuboot-yosemite.c simpleboot.c \
-		virtex405-head.S
+		virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))
@@ -213,6 +215,7 @@ image-$(CONFIG_WALNUT)			+= treeImage.walnut
 # Board ports in arch/powerpc/platform/44x/Kconfig
 image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
 image-$(CONFIG_BAMBOO)			+= treeImage.bamboo cuImage.bamboo
+image-$(CONFIG_SAM440EP)		+= cuImage.sam440ep
 image-$(CONFIG_SEQUOIA)			+= cuImage.sequoia
 image-$(CONFIG_RAINIER)			+= cuImage.rainier
 image-$(CONFIG_TAISHAN)			+= cuImage.taishan
@@ -242,6 +245,7 @@ image-$(CONFIG_MPC834x_ITX)		+= cuImage.mpc8349emitx \
 					   cuImage.mpc8349emitxgp
 image-$(CONFIG_MPC834x_MDS)		+= cuImage.mpc834x_mds
 image-$(CONFIG_MPC836x_MDS)		+= cuImage.mpc836x_mds
+image-$(CONFIG_ASP834x)			+= dtbImage.asp834x-redboot
 
 # Board ports in arch/powerpc/platform/85xx/Kconfig
 image-$(CONFIG_MPC8540_ADS)		+= cuImage.mpc8540ads
@@ -254,6 +258,7 @@ image-$(CONFIG_MPC85xx_DS)		+= cuImage.mpc8544ds \
 					   cuImage.mpc8572ds
 image-$(CONFIG_TQM8540)			+= cuImage.tqm8540
 image-$(CONFIG_TQM8541)			+= cuImage.tqm8541
+image-$(CONFIG_TQM8548)			+= cuImage.tqm8548
 image-$(CONFIG_TQM8555)			+= cuImage.tqm8555
 image-$(CONFIG_TQM8560)			+= cuImage.tqm8560
 image-$(CONFIG_SBC8548)			+= cuImage.sbc8548
@@ -263,6 +268,7 @@ image-$(CONFIG_KSI8560)			+= cuImage.ksi8560
 # Board ports in arch/powerpc/platform/embedded6xx/Kconfig
 image-$(CONFIG_STORCENTER)		+= cuImage.storcenter
 image-$(CONFIG_MPC7448HPC2)		+= cuImage.mpc7448hpc2
+image-$(CONFIG_PPC_C2K)			+= cuImage.c2k
 
 # For 32-bit powermacs, build the COFF and miboot images
 # as well as the ELF images.
@@ -270,6 +276,9 @@ ifeq ($(CONFIG_PPC32),y)
 image-$(CONFIG_PPC_PMAC)	+= zImage.coff zImage.miboot
 endif
 
+# Allow extra targets to be added to the defconfig
+image-y	+= $(subst ",,$(CONFIG_EXTRA_TARGETS))
+
 initrd-  := $(patsubst zImage%, zImage.initrd%, $(image-n) $(image-))
 initrd-y := $(patsubst zImage%, zImage.initrd%, \
 		$(patsubst dtbImage%, dtbImage.initrd%, \

arch/powerpc/boot/addnote.c

@@ -25,7 +25,7 @@ char arch[] = "PowerPC";
 #define N_DESCR	6
 unsigned int descr[N_DESCR] = {
 	0xffffffff,		/* real-mode = true */
-	0x00c00000,		/* real-base, i.e. where we expect OF to be */
+	0x02000000,		/* real-base, i.e. where we expect OF to be */
 	0xffffffff,		/* real-size */
 	0xffffffff,		/* virt-base */
 	0xffffffff,		/* virt-size */

arch/powerpc/boot/cuboot-c2k.c

+/*
+ * GEFanuc C2K platform code.
+ *
+ * Author: Remi Machet <rmachet@slac.stanford.edu>
+ *
+ * Originated from prpmc2800.c
+ *
+ * 2008 (c) Stanford University
+ * 2007 (c) MontaVista, Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "types.h"
+#include "stdio.h"
+#include "io.h"
+#include "ops.h"
+#include "elf.h"
+#include "gunzip_util.h"
+#include "mv64x60.h"
+#include "cuboot.h"
+#include "ppcboot.h"
+
+static u8 *bridge_base;
+
+static void c2k_bridge_setup(u32 mem_size)
+{
+	u32 i, v[30], enables, acc_bits;
+	u32 pci_base_hi, pci_base_lo, size, buf[2];
+	unsigned long cpu_base;
+	int rc;
+	void *devp, *mv64x60_devp;
+	u8 *bridge_pbase, is_coherent;
+	struct mv64x60_cpu2pci_win *tbl;
+	int bus;
+
+	bridge_pbase = mv64x60_get_bridge_pbase();
+	is_coherent = mv64x60_is_coherent();
+
+	if (is_coherent)
+		acc_bits = MV64x60_PCI_ACC_CNTL_SNOOP_WB
+			| MV64x60_PCI_ACC_CNTL_SWAP_NONE
+			| MV64x60_PCI_ACC_CNTL_MBURST_32_BYTES
+			| MV64x60_PCI_ACC_CNTL_RDSIZE_32_BYTES;
+	else
+		acc_bits = MV64x60_PCI_ACC_CNTL_SNOOP_NONE
+			| MV64x60_PCI_ACC_CNTL_SWAP_NONE
+			| MV64x60_PCI_ACC_CNTL_MBURST_128_BYTES
+			| MV64x60_PCI_ACC_CNTL_RDSIZE_256_BYTES;
+
+	mv64x60_config_ctlr_windows(bridge_base, bridge_pbase, is_coherent);
+	mv64x60_devp = find_node_by_compatible(NULL, "marvell,mv64360");
+	if (mv64x60_devp == NULL)
+		fatal("Error: Missing marvell,mv64360 device tree node\n\r");
+
+	enables = in_le32((u32 *)(bridge_base + MV64x60_CPU_BAR_ENABLE));
+	enables |= 0x007ffe00; /* Disable all cpu->pci windows */
+	out_le32((u32 *)(bridge_base + MV64x60_CPU_BAR_ENABLE), enables);
+
+	/* Get the cpu -> pci i/o & mem mappings from the device tree */
+	devp = NULL;
+	for (bus = 0; ; bus++) {
+		char name[] = "pci ";
+
+		name[strlen(name)-1] = bus+'0';
+
+		devp = find_node_by_alias(name);
+		if (devp == NULL)
+			break;
+
+		if (bus >= 2)
+			fatal("Error: Only 2 PCI controllers are supported at" \
+				" this time.\n");
+
+		mv64x60_config_pci_windows(bridge_base, bridge_pbase, bus, 0,
+				mem_size, acc_bits);
+
+		rc = getprop(devp, "ranges", v, sizeof(v));
+		if (rc == 0)
+			fatal("Error: Can't find marvell,mv64360-pci ranges"
+				" property\n\r");
+
+		/* Get the cpu -> pci i/o & mem mappings from the device tree */
+
+		for (i = 0; i < rc; i += 6) {
+			switch (v[i] & 0xff000000) {
+			case 0x01000000: /* PCI I/O Space */
+				tbl = mv64x60_cpu2pci_io;
+				break;
+			case 0x02000000: /* PCI MEM Space */
+				tbl = mv64x60_cpu2pci_mem;
+				break;
+			default:
+				continue;
+			}
+
+			pci_base_hi = v[i+1];
+			pci_base_lo = v[i+2];
+			cpu_base = v[i+3];
+			size = v[i+5];
+
+			buf[0] = cpu_base;
+			buf[1] = size;
+
+			if (!dt_xlate_addr(devp, buf, sizeof(buf), &cpu_base))
+				fatal("Error: Can't translate PCI address " \
+						"0x%x\n\r", (u32)cpu_base);
+
+			mv64x60_config_cpu2pci_window(bridge_base, bus,
+				pci_base_hi, pci_base_lo, cpu_base, size, tbl);
+		}
+
+		enables &= ~(3<<(9+bus*5)); /* Enable cpu->pci<bus> i/o,
+						cpu->pci<bus> mem0 */
+		out_le32((u32 *)(bridge_base + MV64x60_CPU_BAR_ENABLE),
+			enables);
+	};
+}
+
+static void c2k_fixups(void)
+{
+	u32 mem_size;
+
+	mem_size = mv64x60_get_mem_size(bridge_base);
+	c2k_bridge_setup(mem_size); /* Do necessary bridge setup */
+}
+
+#define MV64x60_MPP_CNTL_0	0xf000
+#define MV64x60_MPP_CNTL_2	0xf008
+#define MV64x60_GPP_IO_CNTL	0xf100
+#define MV64x60_GPP_LEVEL_CNTL	0xf110
+#define MV64x60_GPP_VALUE_SET	0xf118
+
+static void c2k_reset(void)
+{
+	u32 temp;
+
+	udelay(5000000);
+
+	if (bridge_base != 0) {
+		temp = in_le32((u32 *)(bridge_base + MV64x60_MPP_CNTL_0));
+		temp &= 0xFFFF0FFF;
+		out_le32((u32 *)(bridge_base + MV64x60_MPP_CNTL_0), temp);
+
+		temp = in_le32((u32 *)(bridge_base + MV64x60_GPP_LEVEL_CNTL));
+		temp |= 0x00000004;
+		out_le32((u32 *)(bridge_base + MV64x60_GPP_LEVEL_CNTL), temp);
+
+		temp = in_le32((u32 *)(bridge_base + MV64x60_GPP_IO_CNTL));
+		temp |= 0x00000004;
+		out_le32((u32 *)(bridge_base + MV64x60_GPP_IO_CNTL), temp);
+
+		temp = in_le32((u32 *)(bridge_base + MV64x60_MPP_CNTL_2));
+		temp &= 0xFFFF0FFF;
+		out_le32((u32 *)(bridge_base + MV64x60_MPP_CNTL_2), temp);
+
+		temp = in_le32((u32 *)(bridge_base + MV64x60_GPP_LEVEL_CNTL));
+		temp |= 0x00080000;
+		out_le32((u32 *)(bridge_base + MV64x60_GPP_LEVEL_CNTL), temp);
+
+		temp = in_le32((u32 *)(bridge_base + MV64x60_GPP_IO_CNTL));
+		temp |= 0x00080000;
+		out_le32((u32 *)(bridge_base + MV64x60_GPP_IO_CNTL), temp);
+
+		out_le32((u32 *)(bridge_base + MV64x60_GPP_VALUE_SET),
+				0x00080004);
+	}
+
+	for (;;);
+}
+
+static bd_t bd;
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+			unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+
+	fdt_init(_dtb_start);
+
+	bridge_base = mv64x60_get_bridge_base();
+
+	platform_ops.fixups = c2k_fixups;
+	platform_ops.exit = c2k_reset;
+
+	if (serial_console_init() < 0)
+		exit();
+}

arch/powerpc/boot/cuboot-sam440ep.c

+/*
+ * Old U-boot compatibility for Sam440ep based off bamboo.c code
+ * original copyrights below
+ *
+ * Author: Josh Boyer <jwboyer@linux.vnet.ibm.com>
+ *
+ * Copyright 2007 IBM Corporation
+ *
+ * Based on cuboot-ebony.c
+ *
+ * Modified from cuboot-bamboo.c for sam440ep:
+ * Copyright 2008 Giuseppe Coviello <gicoviello@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "44x.h"
+#include "4xx.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#define TARGET_44x
+#include "ppcboot.h"
+
+static bd_t bd;
+
+static void sam440ep_fixups(void)
+{
+       unsigned long sysclk = 66666666;
+
+       ibm440ep_fixup_clocks(sysclk, 11059200, 25000000);
+       ibm4xx_sdram_fixup_memsize();
+       ibm4xx_quiesce_eth((u32 *)0xef600e00, (u32 *)0xef600f00);
+       dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+		unsigned long r6, unsigned long r7)
+{
+	CUBOOT_INIT();
+	platform_ops.fixups = sam440ep_fixups;
+	platform_ops.exit = ibm44x_dbcr_reset;
+	fdt_init(_dtb_start);
+	serial_console_init();
+}

arch/powerpc/boot/cuboot-warp.c

@@ -10,6 +10,7 @@
 #include "ops.h"
 #include "4xx.h"
 #include "cuboot.h"
+#include "stdio.h"
 
 #define TARGET_4xx
 #define TARGET_44x
@@ -17,14 +18,54 @@
 
 static bd_t bd;
 
-static void warp_fixups(void)
+static void warp_fixup_one_nor(u32 from, u32 to)
 {
-	unsigned long sysclk = 66000000;
+	void *devp;
+	char name[50];
+	u32 v[2];
+
+	sprintf(name, "/plb/opb/ebc/nor_flash@0,0/partition@%x", from);
+
+	devp = finddevice(name);
+	if (!devp)
+		return;
+
+	if (getprop(devp, "reg", v, sizeof(v)) == sizeof(v)) {
+		v[0] = to;
+		setprop(devp, "reg", v, sizeof(v));
+
+		printf("NOR 64M fixup %x -> %x\r\n", from, to);
+	}
+}
+
 
-	ibm440ep_fixup_clocks(sysclk, 11059200, 50000000);
+static void warp_fixups(void)
+{
+	ibm440ep_fixup_clocks(66000000, 11059200, 50000000);
 	ibm4xx_sdram_fixup_memsize();
 	ibm4xx_fixup_ebc_ranges("/plb/opb/ebc");
 	dt_fixup_mac_address_by_alias("ethernet0", bd.bi_enetaddr);
+
+	/* Fixup for 64M flash on Rev A boards. */
+	if (bd.bi_flashsize == 0x4000000) {
+		void *devp;
+		u32 v[3];
+
+		devp = finddevice("/plb/opb/ebc/nor_flash@0,0");
+		if (!devp)
+			return;
+
+		/* Fixup the size */
+		if (getprop(devp, "reg", v, sizeof(v)) == sizeof(v)) {
+			v[2] = bd.bi_flashsize;
+			setprop(devp, "reg", v, sizeof(v));
+		}
+
+		/* Fixup parition offsets */
+		warp_fixup_one_nor(0x300000, 0x3f00000);
+		warp_fixup_one_nor(0x340000, 0x3f40000);
+		warp_fixup_one_nor(0x380000, 0x3f80000);
+	}
 }
 
 

arch/powerpc/boot/dts/asp834x-redboot.dts

+/*
+ * Analogue & Micro ASP8347 Device Tree Source
+ *
+ * Copyright 2008 Codehermit
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	model = "Analogue & Micro ASP8347E";
+	compatible = "analogue-and-micro,asp8347e";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		serial0 = &serial0;
+		serial1 = &serial1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8347@0 {
+			device_type = "cpu";
+			reg = <0x0>;
+			d-cache-line-size = <32>;
+			i-cache-line-size = <32>;
+			d-cache-size = <32768>;
+			i-cache-size = <32768>;
+			timebase-frequency = <0>;	// from bootloader
+			bus-frequency = <0>;		// from bootloader
+			clock-frequency = <0>;		// from bootloader
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;	// 128MB at 0
+	};
+
+	localbus@ff005000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8347e-localbus",
+			     "fsl,pq2pro-localbus",
+			     "simple-bus";
+		reg = <0xff005000 0x1000>;
+		interrupts = <77 0x8>;
+		interrupt-parent = <&ipic>;
+
+		ranges = <
+			0 0 0xf0000000 0x02000000
+		>;
+
+		flash@0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x02000000>;
+			bank-width = <2>;
+			device-width = <2>;
+		};
+	};
+
+	soc8349@ff000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		ranges = <0x0 0xff000000 0x00100000>;
+		reg = <0xff000000 0x00000200>;
+		bus-frequency = <0>;
+
+		wdt@200 {
+			device_type = "watchdog";
+			compatible = "mpc83xx_wdt";
+			reg = <0x200 0x100>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <14 0x8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+
+			rtc@68 {
+				compatible = "dallas,ds1374";
+				reg = <0x68>;
+			};
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <15 0x8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		spi@7000 {
+			cell-index = <0>;
+			compatible = "fsl,spi";
+			reg = <0x7000 0x1000>;
+			interrupts = <16 0x8>;
+			interrupt-parent = <&ipic>;
+			mode = "cpu";
+		};
+
+		dma@82a8 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc8347-dma", "fsl,elo-dma";
+			reg = <0x82a8 4>;
+			ranges = <0 0x8100 0x1a8>;
+			interrupt-parent = <&ipic>;
+			interrupts = <71 8>;
+			cell-index = <0>;
+			dma-channel@0 {
+				compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+				reg = <0 0x80>;
+				interrupt-parent = <&ipic>;
+				interrupts = <71 8>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+				reg = <0x80 0x80>;
+				interrupt-parent = <&ipic>;
+				interrupts = <71 8>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+				reg = <0x100 0x80>;
+				interrupt-parent = <&ipic>;
+				interrupts = <71 8>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,mpc8347-dma-channel", "fsl,elo-dma-channel";
+				reg = <0x180 0x28>;
+				interrupt-parent = <&ipic>;
+				interrupts = <71 8>;
+			};
+		};
+
+		/* phy type (ULPI or SERIAL) are only types supported for MPH */
+		/* port = 0 or 1 */
+		usb@22000 {
+			compatible = "fsl-usb2-mph";
+			reg = <0x22000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&ipic>;
+			interrupts = <39 0x8>;
+			phy_type = "ulpi";
+			port1;
+		};
+		/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
+		usb@23000 {
+			compatible = "fsl-usb2-dr";
+			reg = <0x23000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&ipic>;
+			interrupts = <38 0x8>;
+			dr_mode = "otg";
+			phy_type = "ulpi";
+		};
+
+		mdio@24520 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,gianfar-mdio";
+			reg = <0x24520 0x20>;
+
+			phy0: ethernet-phy@0 {
+				interrupt-parent = <&ipic>;
+				interrupts = <17 0x8>;
+				reg = <0x1>;
+				device_type = "ethernet-phy";
+			};
+			phy1: ethernet-phy@1 {
+				interrupt-parent = <&ipic>;
+				interrupts = <18 0x8>;
+				reg = <0x2>;
+				device_type = "ethernet-phy";
+			};
+		};
+
+		enet0: ethernet@24000 {
+			cell-index = <0>;
+			device_type = "network";
+			model = "TSEC";
+			compatible = "gianfar";
+			reg = <0x24000 0x1000>;
+			local-mac-address = [ 00 08 e5 11 32 33 ];
+			interrupts = <32 0x8 33 0x8 34 0x8>;
+			interrupt-parent = <&ipic>;
+			phy-handle = <&phy0>;
+			linux,network-index = <0>;
+		};
+
+		enet1: ethernet@25000 {
+			cell-index = <1>;
+			device_type = "network";
+			model = "TSEC";
+			compatible = "gianfar";
+			reg = <0x25000 0x1000>;
+			local-mac-address = [ 00 08 e5 11 32 34 ];
+			interrupts = <35 0x8 36 0x8 37 0x8>;
+			interrupt-parent = <&ipic>;
+			phy-handle = <&phy1>;
+			linux,network-index = <1>;
+		};
+
+		serial0: serial@4500 {
+			cell-index = <0>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			clock-frequency = <400000000>;
+			interrupts = <9 0x8>;
+			interrupt-parent = <&ipic>;
+		};
+
+		serial1: serial@4600 {
+			cell-index = <1>;
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			clock-frequency = <400000000>;
+			interrupts = <10 0x8>;
+			interrupt-parent = <&ipic>;
+		};
+
+		/* May need to remove if on a part without crypto engine */
+		crypto@30000 {
+			device_type = "crypto";
+			model = "SEC2";
+			compatible = "talitos";
+			reg = <0x30000 0x10000>;
+			interrupts = <11 0x8>;
+			interrupt-parent = <&ipic>;
+			num-channels = <4>;
+			channel-fifo-len = <24>;
+			exec-units-mask = <0x0000007e>;
+			/* desc mask is for rev2.0,
+			 * we need runtime fixup for >2.0 */
+			descriptor-types-mask = <0x01010ebf>;
+		};
+
+		/* IPIC
+		 * interrupts cell = <intr #, sense>
+		 * sense values match linux IORESOURCE_IRQ_* defines:
+		 * sense == 8: Level, low assertion
+		 * sense == 2: Edge, high-to-low change
+		 */
+		ipic: pic@700 {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x700 0x100>;
+			device_type = "ipic";
+		};
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,38400 root=/dev/mtdblock3 rootfstype=jffs2";
+		linux,stdout-path = &serial0;
+	};
+
+};

arch/powerpc/boot/dts/bamboo.dts

@@ -11,12 +11,14 @@
  * any warranty of any kind, whether express or implied.
  */
 
+/dts-v1/;
+
 / {
 	#address-cells = <2>;
 	#size-cells = <1>;
 	model = "amcc,bamboo";
 	compatible = "amcc,bamboo";
-	dcr-parent = <&/cpus/cpu@0>;
+	dcr-parent = <&{/cpus/cpu@0}>;
 
 	aliases {
 		ethernet0 = &EMAC0;
@@ -34,13 +36,13 @@
 		cpu@0 {
 			device_type = "cpu";
 			model = "PowerPC,440EP";
-			reg = <0>;
+			reg = <0x00000000>;
 			clock-frequency = <0>; /* Filled in by zImage */
 			timebase-frequency = <0>; /* Filled in by zImage */
-			i-cache-line-size = <20>;
-			d-cache-line-size = <20>;
-			i-cache-size = <8000>;
-			d-cache-size = <8000>;
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <32768>;
+			d-cache-size = <32768>;
 			dcr-controller;
 			dcr-access-method = "native";
 		};
@@ -48,14 +50,14 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0 0 0>; /* Filled in by zImage */
+		reg = <0x00000000 0x00000000 0x00000000>; /* Filled in by zImage */
 	};
 
 	UIC0: interrupt-controller0 {
 		compatible = "ibm,uic-440ep","ibm,uic";
 		interrupt-controller;
 		cell-index = <0>;
-		dcr-reg = <0c0 009>;
+		dcr-reg = <0x0c0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
@@ -65,22 +67,22 @@
 		compatible = "ibm,uic-440ep","ibm,uic";
 		interrupt-controller;
 		cell-index = <1>;
-		dcr-reg = <0d0 009>;
+		dcr-reg = <0x0d0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
-		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
 		interrupt-parent = <&UIC0>;
 	};
 
 	SDR0: sdr {
 		compatible = "ibm,sdr-440ep";
-		dcr-reg = <00e 002>;
+		dcr-reg = <0x00e 0x002>;
 	};
 
 	CPR0: cpr {
 		compatible = "ibm,cpr-440ep";
-		dcr-reg = <00c 002>;
+		dcr-reg = <0x00c 0x002>;
 	};
 
 	plb {
@@ -92,29 +94,29 @@
 
 		SDRAM0: sdram {
 			compatible = "ibm,sdram-440ep", "ibm,sdram-405gp";
-			dcr-reg = <010 2>;
+			dcr-reg = <0x010 0x002>;
 		};
 
 		DMA0: dma {
 			compatible = "ibm,dma-440ep", "ibm,dma-440gp";
-			dcr-reg = <100 027>;
+			dcr-reg = <0x100 0x027>;
 		};
 
 		MAL0: mcmal {
 			compatible = "ibm,mcmal-440ep", "ibm,mcmal-440gp", "ibm,mcmal";
-			dcr-reg = <180 62>;
+			dcr-reg = <0x180 0x062>;
 			num-tx-chans = <4>;
 			num-rx-chans = <2>;
 			interrupt-parent = <&MAL0>;
-			interrupts = <0 1 2 3 4>;
+			interrupts = <0x0 0x1 0x2 0x3 0x4>;
 			#interrupt-cells = <1>;
 			#address-cells = <0>;
 			#size-cells = <0>;
-			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
-					/*RXEOB*/ 1 &UIC0 b 4
-					/*SERR*/  2 &UIC1 0 4
-					/*TXDE*/  3 &UIC1 1 4
-					/*RXDE*/  4 &UIC1 2 4>;
+			interrupt-map = </*TXEOB*/ 0x0 &UIC0 0xa 0x4
+					/*RXEOB*/ 0x1 &UIC0 0xb 0x4
+					/*SERR*/  0x2 &UIC1 0x0 0x4
+					/*TXDE*/  0x3 &UIC1 0x1 0x4
+					/*RXDE*/  0x4 &UIC1 0x2 0x4>;
 		};
 
 		POB0: opb {
@@ -124,101 +126,101 @@
 			/* Bamboo is oddball in the 44x world and doesn't use the ERPN
 			 * bits.
 			 */
-		  	ranges = <00000000 0 00000000 80000000
-			          80000000 0 80000000 80000000>;
+		  	ranges = <0x00000000 0x00000000 0x00000000 0x80000000
+			          0x80000000 0x00000000 0x80000000 0x80000000>;
 		  	interrupt-parent = <&UIC1>;
-		  	interrupts = <7 4>;
+		  	interrupts = <0x7 0x4>;
 		  	clock-frequency = <0>; /* Filled in by zImage */
 
 			EBC0: ebc {
 				compatible = "ibm,ebc-440ep", "ibm,ebc-440gp", "ibm,ebc";
-				dcr-reg = <012 2>;
+				dcr-reg = <0x012 0x002>;
 				#address-cells = <2>;
 				#size-cells = <1>;
 				clock-frequency = <0>; /* Filled in by zImage */
-				interrupts = <5 1>;
+				interrupts = <0x5 0x1>;
 				interrupt-parent = <&UIC1>;
 			};
 
 			UART0: serial@ef600300 {
 		   		device_type = "serial";
 		   		compatible = "ns16550";
-		   		reg = <ef600300 8>;
-		   		virtual-reg = <ef600300>;
+		   		reg = <0xef600300 0x00000008>;
+		   		virtual-reg = <0xef600300>;
 		   		clock-frequency = <0>; /* Filled in by zImage */
-		   		current-speed = <1c200>;
+		   		current-speed = <115200>;
 		   		interrupt-parent = <&UIC0>;
-		   		interrupts = <0 4>;
+		   		interrupts = <0x0 0x4>;
 	   		};
 
 			UART1: serial@ef600400 {
 		   		device_type = "serial";
 		   		compatible = "ns16550";
-		   		reg = <ef600400 8>;
-		   		virtual-reg = <ef600400>;
+		   		reg = <0xef600400 0x00000008>;
+		   		virtual-reg = <0xef600400>;
 		   		clock-frequency = <0>;
 		   		current-speed = <0>;
 		   		interrupt-parent = <&UIC0>;
-		   		interrupts = <1 4>;
+		   		interrupts = <0x1 0x4>;
 	   		};
 
 			UART2: serial@ef600500 {
 		   		device_type = "serial";
 		   		compatible = "ns16550";
-		   		reg = <ef600500 8>;
-		   		virtual-reg = <ef600500>;
+		   		reg = <0xef600500 0x00000008>;
+		   		virtual-reg = <0xef600500>;
 		   		clock-frequency = <0>;
 		   		current-speed = <0>;
 		   		interrupt-parent = <&UIC0>;
-		   		interrupts = <3 4>;
+		   		interrupts = <0x3 0x4>;
 	   		};
 
 			UART3: serial@ef600600 {
 		   		device_type = "serial";
 		   		compatible = "ns16550";
-		   		reg = <ef600600 8>;
-		   		virtual-reg = <ef600600>;
+		   		reg = <0xef600600 0x00000008>;
+		   		virtual-reg = <0xef600600>;
 		   		clock-frequency = <0>;
 		   		current-speed = <0>;
 		   		interrupt-parent = <&UIC0>;
-		   		interrupts = <4 4>;
+		   		interrupts = <0x4 0x4>;
 	   		};
 
 			IIC0: i2c@ef600700 {
 				compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
-				reg = <ef600700 14>;
+				reg = <0xef600700 0x00000014>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <2 4>;
+				interrupts = <0x2 0x4>;
 			};
 
 			IIC1: i2c@ef600800 {
 				compatible = "ibm,iic-440ep", "ibm,iic-440gp", "ibm,iic";
-				reg = <ef600800 14>;
+				reg = <0xef600800 0x00000014>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <7 4>;
+				interrupts = <0x7 0x4>;
 			};
 
 			ZMII0: emac-zmii@ef600d00 {
 				compatible = "ibm,zmii-440ep", "ibm,zmii-440gp", "ibm,zmii";
-				reg = <ef600d00 c>;
+				reg = <0xef600d00 0x0000000c>;
 			};
 
 			EMAC0: ethernet@ef600e00 {
 				device_type = "network";
 				compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
 				interrupt-parent = <&UIC1>;
-				interrupts = <1c 4 1d 4>;
-				reg = <ef600e00 70>;
+				interrupts = <0x1c 0x4 0x1d 0x4>;
+				reg = <0xef600e00 0x00000070>;
 				local-mac-address = [000000000000];
 				mal-device = <&MAL0>;
 				mal-tx-channel = <0 1>;
 				mal-rx-channel = <0>;
 				cell-index = <0>;
-				max-frame-size = <5dc>;
-				rx-fifo-size = <1000>;
-				tx-fifo-size = <800>;
+				max-frame-size = <1500>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
 				phy-mode = "rmii";
-				phy-map = <00000000>;
+				phy-map = <0x00000000>;
 				zmii-device = <&ZMII0>;
 				zmii-channel = <0>;
 			};
@@ -227,26 +229,26 @@
 				device_type = "network";
 				compatible = "ibm,emac-440ep", "ibm,emac-440gp", "ibm,emac";
 				interrupt-parent = <&UIC1>;
-				interrupts = <1e 4 1f 4>;
-				reg = <ef600f00 70>;
+				interrupts = <0x1e 0x4 0x1f 0x4>;
+				reg = <0xef600f00 0x00000070>;
 				local-mac-address = [000000000000];
 				mal-device = <&MAL0>;
 				mal-tx-channel = <2 3>;
 				mal-rx-channel = <1>;
 				cell-index = <1>;
-				max-frame-size = <5dc>;
-				rx-fifo-size = <1000>;
-				tx-fifo-size = <800>;
+				max-frame-size = <1500>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
 				phy-mode = "rmii";
-				phy-map = <00000000>;
+				phy-map = <0x00000000>;
 				zmii-device = <&ZMII0>;
 				zmii-channel = <1>;
 			};
 
 			usb@ef601000 {
 				compatible = "ohci-be";
-				reg = <ef601000 80>;
-				interrupts = <8 1 9 1>;
+				reg = <0xef601000 0x00000080>;
+				interrupts = <0x8 0x1 0x9 0x1>;
 				interrupt-parent = < &UIC1 >;
 			};
 		};
@@ -258,35 +260,35 @@
 			#address-cells = <3>;
 			compatible = "ibm,plb440ep-pci", "ibm,plb-pci";
 			primary;
-			reg = <0 eec00000 8	/* Config space access */
-			       0 eed00000 4	/* IACK */
-			       0 eed00000 4	/* Special cycle */
-			       0 ef400000 40>;	/* Internal registers */
+			reg = <0x00000000 0xeec00000 0x00000008	/* Config space access */
+			       0x00000000 0xeed00000 0x00000004	/* IACK */
+			       0x00000000 0xeed00000 0x00000004	/* Special cycle */
+			       0x00000000 0xef400000 0x00000040>;	/* Internal registers */
 
 			/* Outbound ranges, one memory and one IO,
 			 * later cannot be changed. Chip supports a second
 			 * IO range but we don't use it for now
 			 */
-			ranges = <02000000 0 a0000000 0 a0000000 0 20000000
-				  01000000 0 00000000 0 e8000000 0 00010000>;
+			ranges = <0x02000000 0x00000000 0xa0000000 0x00000000 0xa0000000 0x00000000 0x20000000
+				  0x01000000 0x00000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
 
 			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <42000000 0 0 0 0 0 80000000>;
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
 
 			/* Bamboo has all 4 IRQ pins tied together per slot */
-			interrupt-map-mask = <f800 0 0 0>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x0>;
 			interrupt-map = <
 				/* IDSEL 1 */
-				0800 0 0 0 &UIC0 1c 8
+				0x800 0x0 0x0 0x0 &UIC0 0x1c 0x8
 
 				/* IDSEL 2 */
-				1000 0 0 0 &UIC0 1b 8
+				0x1000 0x0 0x0 0x0 &UIC0 0x1b 0x8
 
 				/* IDSEL 3 */
-				1800 0 0 0 &UIC0 1a 8
+				0x1800 0x0 0x0 0x0 &UIC0 0x1a 0x8
 
 				/* IDSEL 4 */
-				2000 0 0 0 &UIC0 19 8
+				0x2000 0x0 0x0 0x0 &UIC0 0x19 0x8
 			>;
 		};
 	};

arch/powerpc/boot/dts/c2k.dts

+/* Device Tree Source for GEFanuc C2K
+ *
+ * Author: Remi Machet <rmachet@slac.stanford.edu>
+ *
+ * Originated from prpmc2800.dts
+ *
+ * 2008 (c) Stanford University
+ * 2007 (c) MontaVista, Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "C2K";
+	compatible = "GEFanuc,C2K";
+	coherency-off;
+
+	aliases {
+		pci0 = &PCI0;
+		pci1 = &PCI1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "PowerPC,7447";
+			reg = <0>;
+			clock-frequency = <996000000>;	/* 996 MHz */
+			bus-frequency = <166666667>;	/* 166.6666 MHz */
+			timebase-frequency = <41666667>;	/* 166.6666/4 MHz */
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <32768>;
+			d-cache-size = <32768>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>;	/* 1GB */
+	};
+
+	system-controller@d8000000 { /* Marvell Discovery */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		model = "mv64460";
+		compatible = "marvell,mv64360";
+		clock-frequency = <166666667>;		/* 166.66... MHz */
+		reg = <0xd8000000 0x00010000>;
+		virtual-reg = <0xd8000000>;
+		ranges = <0xd4000000 0xd4000000 0x01000000	/* PCI 0 I/O Space */
+			  0x80000000 0x80000000 0x08000000	/* PCI 0 MEM Space */
+			  0xd0000000 0xd0000000 0x01000000	/* PCI 1 I/O Space */
+			  0xa0000000 0xa0000000 0x08000000	/* PCI 1 MEM Space */
+			  0xd8100000 0xd8100000 0x00010000	/* FPGA */
+			  0xd8110000 0xd8110000 0x00010000	/* FPGA USARTs */
+			  0xf8000000 0xf8000000 0x08000000	/* User FLASH */
+			  0x00000000 0xd8000000 0x00010000	/* Bridge's regs */
+			  0xd8140000 0xd8140000 0x00040000>;	/* Integrated SRAM */
+
+		mdio@2000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "marvell,mv64360-mdio";
+			reg = <0x2000 4>;
+			PHY0: ethernet-phy@0 {
+				device_type = "ethernet-phy";
+				interrupts = <76>;	/* GPP 12 */
+				interrupt-parent = <&PIC>;
+				reg = <0>;
+			};
+			PHY1: ethernet-phy@1 {
+				device_type = "ethernet-phy";
+				interrupts = <76>;	/* GPP 12 */
+				interrupt-parent = <&PIC>;
+				reg = <1>;
+			};
+			PHY2: ethernet-phy@2 {
+				device_type = "ethernet-phy";
+				interrupts = <76>;	/* GPP 12 */
+				interrupt-parent = <&PIC>;
+				reg = <2>;
+			};
+		};
+
+		ethernet-group@2000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "marvell,mv64360-eth-group";
+			reg = <0x2000 0x2000>;
+			ethernet@0 {
+				device_type = "network";
+				compatible = "marvell,mv64360-eth";
+				reg = <0>;
+				interrupts = <32>;
+				interrupt-parent = <&PIC>;
+				phy = <&PHY0>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+			ethernet@1 {
+				device_type = "network";
+				compatible = "marvell,mv64360-eth";
+				reg = <1>;
+				interrupts = <33>;
+				interrupt-parent = <&PIC>;
+				phy = <&PHY1>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+			ethernet@2 {
+				device_type = "network";
+				compatible = "marvell,mv64360-eth";
+				reg = <2>;
+				interrupts = <34>;
+				interrupt-parent = <&PIC>;
+				phy = <&PHY2>;
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+		};
+
+		SDMA0: sdma@4000 {
+			compatible = "marvell,mv64360-sdma";
+			reg = <0x4000 0xc18>;
+			virtual-reg = <0xd8004000>;
+			interrupt-base = <0>;
+			interrupts = <36>;
+			interrupt-parent = <&PIC>;
+		};
+
+		SDMA1: sdma@6000 {
+			compatible = "marvell,mv64360-sdma";
+			reg = <0x6000 0xc18>;
+			virtual-reg = <0xd8006000>;
+			interrupt-base = <0>;
+			interrupts = <38>;
+			interrupt-parent = <&PIC>;
+		};
+
+		BRG0: brg@b200 {
+			compatible = "marvell,mv64360-brg";
+			reg = <0xb200 0x8>;
+			clock-src = <8>;
+			clock-frequency = <133333333>;
+			current-speed = <115200>;
+		};
+
+		BRG1: brg@b208 {
+			compatible = "marvell,mv64360-brg";
+			reg = <0xb208 0x8>;
+			clock-src = <8>;
+			clock-frequency = <133333333>;
+			current-speed = <115200>;
+		};
+
+		CUNIT: cunit@f200 {
+			reg = <0xf200 0x200>;
+		};
+
+		MPSCROUTING: mpscrouting@b400 {
+			reg = <0xb400 0xc>;
+		};
+
+		MPSCINTR: mpscintr@b800 {
+			reg = <0xb800 0x100>;
+			virtual-reg = <0xd800b800>;
+		};
+
+		MPSC0: mpsc@8000 {
+			device_type = "serial";
+			compatible = "marvell,mv64360-mpsc";
+			reg = <0x8000 0x38>;
+			virtual-reg = <0xd8008000>;
+			sdma = <&SDMA0>;
+			brg = <&BRG0>;
+			cunit = <&CUNIT>;
+			mpscrouting = <&MPSCROUTING>;
+			mpscintr = <&MPSCINTR>;
+			cell-index = <0>;
+			interrupts = <40>;
+			interrupt-parent = <&PIC>;
+		};
+
+		MPSC1: mpsc@9000 {
+			device_type = "serial";
+			compatible = "marvell,mv64360-mpsc";
+			reg = <0x9000 0x38>;
+			virtual-reg = <0xd8009000>;
+			sdma = <&SDMA1>;
+			brg = <&BRG1>;
+			cunit = <&CUNIT>;
+			mpscrouting = <&MPSCROUTING>;
+			mpscintr = <&MPSCINTR>;
+			cell-index = <1>;
+			interrupts = <42>;
+			interrupt-parent = <&PIC>;
+		};
+
+		wdt@b410 {			/* watchdog timer */
+			compatible = "marvell,mv64360-wdt";
+			reg = <0xb410 0x8>;
+		};
+
+		i2c@c000 {
+			compatible = "marvell,mv64360-i2c";
+			reg = <0xc000 0x20>;
+			virtual-reg = <0xd800c000>;
+			interrupts = <37>;
+			interrupt-parent = <&PIC>;
+		};
+
+		PIC: pic {
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			compatible = "marvell,mv64360-pic";
+			reg = <0x0000 0x88>;
+			interrupt-controller;
+		};
+
+		mpp@f000 {
+			compatible = "marvell,mv64360-mpp";
+			reg = <0xf000 0x10>;
+		};
+
+		gpp@f100 {
+			compatible = "marvell,mv64360-gpp";
+			reg = <0xf100 0x20>;
+		};
+
+		PCI0: pci@80000000 {
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			device_type = "pci";
+			compatible = "marvell,mv64360-pci";
+			reg = <0x0cf8 0x8>;
+			ranges = <0x01000000 0x0 0x00000000 0xd4000000 0x0 0x01000000
+				  0x02000000 0x0 0x80000000 0x80000000 0x0 0x08000000>;
+			bus-range = <0 255>;
+			clock-frequency = <66000000>;
+			interrupt-pci-iack = <0x0c34>;
+			interrupt-parent = <&PIC>;
+			interrupt-map-mask = <0x0000 0x0 0x0 0x7>;
+			interrupt-map = <
+				/* Only one interrupt line for PMC0 slot (INTA) */
+				0x0000 0 0 1 &PIC 88
+			>;
+		};
+
+
+		PCI1: pci@a0000000 {
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			device_type = "pci";
+			compatible = "marvell,mv64360-pci";
+			reg = <0x0c78 0x8>;
+			ranges = <0x01000000 0x0 0x00000000 0xd0000000 0x0 0x01000000
+				  0x02000000 0x0 0x80000000 0xa0000000 0x0 0x08000000>;
+			bus-range = <0 255>;
+			clock-frequency = <66000000>;
+			interrupt-pci-iack = <0x0cb4>;
+			interrupt-parent = <&PIC>;
+			interrupt-map-mask = <0xf800 0x00 0x00 0x7>;
+			interrupt-map = <
+				/* IDSEL 0x01: PMC1 ? */
+				0x0800 0 0 1 &PIC 88
+				/* IDSEL 0x02: cPCI bridge */
+				0x1000 0 0 1 &PIC 88
+				/* IDSEL 0x03: USB controller */
+				0x1800 0 0 1 &PIC 91
+				/* IDSEL 0x04: SATA controller */
+				0x2000 0 0 1 &PIC 95
+			>;
+		};
+
+		cpu-error@0070 {
+			compatible = "marvell,mv64360-cpu-error";
+			reg = <0x0070 0x10 0x0128 0x28>;
+			interrupts = <3>;
+			interrupt-parent = <&PIC>;
+		};
+
+		sram-ctrl@0380 {
+			compatible = "marvell,mv64360-sram-ctrl";
+			reg = <0x0380 0x80>;
+			interrupts = <13>;
+			interrupt-parent = <&PIC>;
+		};
+
+		pci-error@1d40 {
+			compatible = "marvell,mv64360-pci-error";
+			reg = <0x1d40 0x40 0x0c28 0x4>;
+			interrupts = <12>;
+			interrupt-parent = <&PIC>;
+		};
+
+		pci-error@1dc0 {
+			compatible = "marvell,mv64360-pci-error";
+			reg = <0x1dc0 0x40 0x0ca8 0x4>;
+			interrupts = <16>;
+			interrupt-parent = <&PIC>;
+		};
+
+		mem-ctrl@1400 {
+			compatible = "marvell,mv64360-mem-ctrl";
+			reg = <0x1400 0x60>;
+			interrupts = <17>;
+			interrupt-parent = <&PIC>;
+		};
+		/* Devices attached to the device controller */
+		devicebus@045c {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			compatible = "marvell,mv64306-devctrl";
+			reg = <0x45C 0x88>;
+			interrupts = <1>;
+			interrupt-parent = <&PIC>;
+			ranges = 	<0 0 0xd8100000 0x10000
+					 2 0 0xd8110000 0x10000
+					 4 0 0xf8000000 0x8000000>;
+			fpga@0,0 {
+				compatible = "sbs,fpga-c2k";
+				reg = <0 0 0x10000>;
+			};
+			fpga_usart@2,0 {
+				compatible = "sbs,fpga_usart-c2k";
+				reg = <2 0 0x10000>;
+			};
+			nor_flash@4,0 {
+				compatible = "cfi-flash";
+				reg = <4 0 0x8000000>; /* 128MB */
+				bank-width = <4>;
+				device-width = <1>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				partition@0 {
+					label = "boot";
+					reg = <0x00000000 0x00080000>;
+				};
+				partition@40000 {
+					label = "kernel";
+					reg = <0x00080000 0x00400000>;
+				};
+				partition@440000 {
+					label = "initrd";
+					reg = <0x00480000 0x00B80000>;
+				};
+				partition@1000000 {
+					label = "rootfs";
+					reg = <0x01000000 0x06800000>;
+				};
+				partition@7800000 {
+					label = "recovery";
+					reg = <0x07800000 0x00800000>;
+					read-only;
+				};
+			};
+		};
+	};
+	chosen {
+		linux,stdout-path = &MPSC0;
+	};
+};

arch/powerpc/boot/dts/canyonlands.dts

@@ -8,12 +8,14 @@
  * any warranty of any kind, whether express or implied.
  */
 
+/dts-v1/;
+
 / {
 	#address-cells = <2>;
 	#size-cells = <1>;
 	model = "amcc,canyonlands";
 	compatible = "amcc,canyonlands";
-	dcr-parent = <&/cpus/cpu@0>;
+	dcr-parent = <&{/cpus/cpu@0}>;
 
 	aliases {
 		ethernet0 = &EMAC0;
@@ -29,13 +31,13 @@
 		cpu@0 {
 			device_type = "cpu";
 			model = "PowerPC,460EX";
-			reg = <0>;
+			reg = <0x00000000>;
 			clock-frequency = <0>; /* Filled in by U-Boot */
 			timebase-frequency = <0>; /* Filled in by U-Boot */
-			i-cache-line-size = <20>;
-			d-cache-line-size = <20>;
-			i-cache-size = <8000>;
-			d-cache-size = <8000>;
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <32768>;
+			d-cache-size = <32768>;
 			dcr-controller;
 			dcr-access-method = "native";
 		};
@@ -43,14 +45,14 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0 0 0>; /* Filled in by U-Boot */
+		reg = <0x00000000 0x00000000 0x00000000>; /* Filled in by U-Boot */
 	};
 
 	UIC0: interrupt-controller0 {
 		compatible = "ibm,uic-460ex","ibm,uic";
 		interrupt-controller;
 		cell-index = <0>;
-		dcr-reg = <0c0 009>;
+		dcr-reg = <0x0c0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
@@ -60,11 +62,11 @@
 		compatible = "ibm,uic-460ex","ibm,uic";
 		interrupt-controller;
 		cell-index = <1>;
-		dcr-reg = <0d0 009>;
+		dcr-reg = <0x0d0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
-		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
 		interrupt-parent = <&UIC0>;
 	};
 
@@ -72,11 +74,11 @@
 		compatible = "ibm,uic-460ex","ibm,uic";
 		interrupt-controller;
 		cell-index = <2>;
-		dcr-reg = <0e0 009>;
+		dcr-reg = <0x0e0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
-		interrupts = <a 4 b 4>; /* cascade */
+		interrupts = <0xa 0x4 0xb 0x4>; /* cascade */
 		interrupt-parent = <&UIC0>;
 	};
 
@@ -84,22 +86,22 @@
 		compatible = "ibm,uic-460ex","ibm,uic";
 		interrupt-controller;
 		cell-index = <3>;
-		dcr-reg = <0f0 009>;
+		dcr-reg = <0x0f0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
-		interrupts = <10 4 11 4>; /* cascade */
+		interrupts = <0x10 0x4 0x11 0x4>; /* cascade */
 		interrupt-parent = <&UIC0>;
 	};
 
 	SDR0: sdr {
 		compatible = "ibm,sdr-460ex";
-		dcr-reg = <00e 002>;
+		dcr-reg = <0x00e 0x002>;
 	};
 
 	CPR0: cpr {
 		compatible = "ibm,cpr-460ex";
-		dcr-reg = <00c 002>;
+		dcr-reg = <0x00c 0x002>;
 	};
 
 	plb {
@@ -111,74 +113,74 @@
 
 		SDRAM0: sdram {
 			compatible = "ibm,sdram-460ex", "ibm,sdram-405gp";
-			dcr-reg = <010 2>;
+			dcr-reg = <0x010 0x002>;
 		};
 
 		MAL0: mcmal {
 			compatible = "ibm,mcmal-460ex", "ibm,mcmal2";
-			dcr-reg = <180 62>;
+			dcr-reg = <0x180 0x062>;
 			num-tx-chans = <2>;
-			num-rx-chans = <10>;
+			num-rx-chans = <16>;
 			#address-cells = <0>;
 			#size-cells = <0>;
 			interrupt-parent = <&UIC2>;
-			interrupts = <	/*TXEOB*/ 6 4
-					/*RXEOB*/ 7 4
-					/*SERR*/  3 4
-					/*TXDE*/  4 4
-					/*RXDE*/  5 4>;
+			interrupts = <	/*TXEOB*/ 0x6 0x4
+					/*RXEOB*/ 0x7 0x4
+					/*SERR*/  0x3 0x4
+					/*TXDE*/  0x4 0x4
+					/*RXDE*/  0x5 0x4>;
 		};
 
 		POB0: opb {
 			compatible = "ibm,opb-460ex", "ibm,opb";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <b0000000 4 b0000000 50000000>;
+			ranges = <0xb0000000 0x00000004 0xb0000000 0x50000000>;
 			clock-frequency = <0>; /* Filled in by U-Boot */
 
 			EBC0: ebc {
 				compatible = "ibm,ebc-460ex", "ibm,ebc";
-				dcr-reg = <012 2>;
+				dcr-reg = <0x012 0x002>;
 				#address-cells = <2>;
 				#size-cells = <1>;
 				clock-frequency = <0>; /* Filled in by U-Boot */
 				/* ranges property is supplied by U-Boot */
-				interrupts = <6 4>;
+				interrupts = <0x6 0x4>;
 				interrupt-parent = <&UIC1>;
 
 				nor_flash@0,0 {
 					compatible = "amd,s29gl512n", "cfi-flash";
 					bank-width = <2>;
-					reg = <0 000000 4000000>;
+					reg = <0x00000000 0x00000000 0x04000000>;
 					#address-cells = <1>;
 					#size-cells = <1>;
 					partition@0 {
 						label = "kernel";
-						reg = <0 1e0000>;
+						reg = <0x00000000 0x001e0000>;
 					};
 					partition@1e0000 {
 						label = "dtb";
-						reg = <1e0000 20000>;
+						reg = <0x001e0000 0x00020000>;
 					};
 					partition@200000 {
 						label = "ramdisk";
-						reg = <200000 1400000>;
+						reg = <0x00200000 0x01400000>;
 					};
 					partition@1600000 {
 						label = "jffs2";
-						reg = <1600000 400000>;
+						reg = <0x01600000 0x00400000>;
 					};
 					partition@1a00000 {
 						label = "user";
-						reg = <1a00000 2560000>;
+						reg = <0x01a00000 0x02560000>;
 					};
 					partition@3f60000 {
 						label = "env";
-						reg = <3f60000 40000>;
+						reg = <0x03f60000 0x00040000>;
 					};
 					partition@3fa0000 {
 						label = "u-boot";
-						reg = <3fa0000 60000>;
+						reg = <0x03fa0000 0x00060000>;
 					};
 				};
 			};
@@ -186,103 +188,103 @@
 			UART0: serial@ef600300 {
 				device_type = "serial";
 				compatible = "ns16550";
-				reg = <ef600300 8>;
-				virtual-reg = <ef600300>;
+				reg = <0xef600300 0x00000008>;
+				virtual-reg = <0xef600300>;
 				clock-frequency = <0>; /* Filled in by U-Boot */
 				current-speed = <0>; /* Filled in by U-Boot */
 				interrupt-parent = <&UIC1>;
-				interrupts = <1 4>;
+				interrupts = <0x1 0x4>;
 			};
 
 			UART1: serial@ef600400 {
 				device_type = "serial";
 				compatible = "ns16550";
-				reg = <ef600400 8>;
-				virtual-reg = <ef600400>;
+				reg = <0xef600400 0x00000008>;
+				virtual-reg = <0xef600400>;
 				clock-frequency = <0>; /* Filled in by U-Boot */
 				current-speed = <0>; /* Filled in by U-Boot */
 				interrupt-parent = <&UIC0>;
-				interrupts = <1 4>;
+				interrupts = <0x1 0x4>;
 			};
 
 			UART2: serial@ef600500 {
 				device_type = "serial";
 				compatible = "ns16550";
-				reg = <ef600500 8>;
-				virtual-reg = <ef600500>;
+				reg = <0xef600500 0x00000008>;
+				virtual-reg = <0xef600500>;
 				clock-frequency = <0>; /* Filled in by U-Boot */
 				current-speed = <0>; /* Filled in by U-Boot */
 				interrupt-parent = <&UIC1>;
-				interrupts = <1d 4>;
+				interrupts = <0x1d 0x4>;
 			};
 
 			UART3: serial@ef600600 {
 				device_type = "serial";
 				compatible = "ns16550";
-				reg = <ef600600 8>;
-				virtual-reg = <ef600600>;
+				reg = <0xef600600 0x00000008>;
+				virtual-reg = <0xef600600>;
 				clock-frequency = <0>; /* Filled in by U-Boot */
 				current-speed = <0>; /* Filled in by U-Boot */
 				interrupt-parent = <&UIC1>;
-				interrupts = <1e 4>;
+				interrupts = <0x1e 0x4>;
 			};
 
 			IIC0: i2c@ef600700 {
 				compatible = "ibm,iic-460ex", "ibm,iic";
-				reg = <ef600700 14>;
+				reg = <0xef600700 0x00000014>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <2 4>;
+				interrupts = <0x2 0x4>;
 			};
 
 			IIC1: i2c@ef600800 {
 				compatible = "ibm,iic-460ex", "ibm,iic";
-				reg = <ef600800 14>;
+				reg = <0xef600800 0x00000014>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <3 4>;
+				interrupts = <0x3 0x4>;
 			};
 
 			ZMII0: emac-zmii@ef600d00 {
 				compatible = "ibm,zmii-460ex", "ibm,zmii";
-				reg = <ef600d00 c>;
+				reg = <0xef600d00 0x0000000c>;
 			};
 
 			RGMII0: emac-rgmii@ef601500 {
 				compatible = "ibm,rgmii-460ex", "ibm,rgmii";
-				reg = <ef601500 8>;
+				reg = <0xef601500 0x00000008>;
 				has-mdio;
 			};
 
 			TAH0: emac-tah@ef601350 {
 				compatible = "ibm,tah-460ex", "ibm,tah";
-				reg = <ef601350 30>;
+				reg = <0xef601350 0x00000030>;
 			};
 
 			TAH1: emac-tah@ef601450 {
 				compatible = "ibm,tah-460ex", "ibm,tah";
-				reg = <ef601450 30>;
+				reg = <0xef601450 0x00000030>;
 			};
 
 			EMAC0: ethernet@ef600e00 {
 				device_type = "network";
-				compatible = "ibm,emac-460ex", "ibm,emac4";
+				compatible = "ibm,emac-460ex", "ibm,emac4sync";
 				interrupt-parent = <&EMAC0>;
-				interrupts = <0 1>;
+				interrupts = <0x0 0x1>;
 				#interrupt-cells = <1>;
 				#address-cells = <0>;
 				#size-cells = <0>;
-				interrupt-map = </*Status*/ 0 &UIC2 10 4
-						 /*Wake*/   1 &UIC2 14 4>;
-				reg = <ef600e00 70>;
+				interrupt-map = </*Status*/ 0x0 &UIC2 0x10 0x4
+						 /*Wake*/   0x1 &UIC2 0x14 0x4>;
+				reg = <0xef600e00 0x000000c4>;
 				local-mac-address = [000000000000]; /* Filled in by U-Boot */
 				mal-device = <&MAL0>;
 				mal-tx-channel = <0>;
 				mal-rx-channel = <0>;
 				cell-index = <0>;
-				max-frame-size = <2328>;
-				rx-fifo-size = <1000>;
-				tx-fifo-size = <800>;
+				max-frame-size = <9000>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
 				phy-mode = "rgmii";
-				phy-map = <00000000>;
+				phy-map = <0x00000000>;
 				rgmii-device = <&RGMII0>;
 				rgmii-channel = <0>;
 				tah-device = <&TAH0>;
@@ -293,25 +295,25 @@
 
 			EMAC1: ethernet@ef600f00 {
 				device_type = "network";
-				compatible = "ibm,emac-460ex", "ibm,emac4";
+				compatible = "ibm,emac-460ex", "ibm,emac4sync";
 				interrupt-parent = <&EMAC1>;
-				interrupts = <0 1>;
+				interrupts = <0x0 0x1>;
 				#interrupt-cells = <1>;
 				#address-cells = <0>;
 				#size-cells = <0>;
-				interrupt-map = </*Status*/ 0 &UIC2 11 4
-						 /*Wake*/   1 &UIC2 15 4>;
-				reg = <ef600f00 70>;
+				interrupt-map = </*Status*/ 0x0 &UIC2 0x11 0x4
+						 /*Wake*/   0x1 &UIC2 0x15 0x4>;
+				reg = <0xef600f00 0x000000c4>;
 				local-mac-address = [000000000000]; /* Filled in by U-Boot */
 				mal-device = <&MAL0>;
 				mal-tx-channel = <1>;
 				mal-rx-channel = <8>;
 				cell-index = <1>;
-				max-frame-size = <2328>;
-				rx-fifo-size = <1000>;
-				tx-fifo-size = <800>;
+				max-frame-size = <9000>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
 				phy-mode = "rgmii";
-				phy-map = <00000000>;
+				phy-map = <0x00000000>;
 				rgmii-device = <&RGMII0>;
 				rgmii-channel = <1>;
 				tah-device = <&TAH1>;
@@ -331,27 +333,27 @@
 			primary;
 			large-inbound-windows;
 			enable-msi-hole;
-			reg = <c 0ec00000   8	/* Config space access */
-			       0 0 0		/* no IACK cycles */
-			       c 0ed00000   4   /* Special cycles */
-			       c 0ec80000 100	/* Internal registers */
-			       c 0ec80100  fc>;	/* Internal messaging registers */
+			reg = <0x0000000c 0x0ec00000   0x00000008	/* Config space access */
+			       0x00000000 0x00000000 0x00000000		/* no IACK cycles */
+			       0x0000000c 0x0ed00000   0x00000004   /* Special cycles */
+			       0x0000000c 0x0ec80000 0x00000100	/* Internal registers */
+			       0x0000000c 0x0ec80100  0x000000fc>;	/* Internal messaging registers */
 
 			/* Outbound ranges, one memory and one IO,
 			 * later cannot be changed
 			 */
-			ranges = <02000000 0 80000000 0000000d 80000000 0 80000000
-				  01000000 0 00000000 0000000c 08000000 0 00010000>;
+			ranges = <0x02000000 0x00000000 0x80000000 0x0000000d 0x80000000 0x00000000 0x80000000
+				  0x01000000 0x00000000 0x00000000 0x0000000c 0x08000000 0x00000000 0x00010000>;
 
 			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <42000000 0 0 0 0 0 80000000>;
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
 
 			/* This drives busses 0 to 0x3f */
-			bus-range = <0 3f>;
+			bus-range = <0x0 0x3f>;
 
 			/* All PCI interrupts are routed to ext IRQ 2 -> UIC1-0 */
-			interrupt-map-mask = <0000 0 0 0>;
-			interrupt-map = < 0000 0 0 0 &UIC1 0 8 >;
+			interrupt-map-mask = <0x0 0x0 0x0 0x0>;
+			interrupt-map = < 0x0 0x0 0x0 0x0 &UIC1 0x0 0x8 >;
 		};
 
 		PCIE0: pciex@d00000000 {
@@ -361,23 +363,23 @@
 			#address-cells = <3>;
 			compatible = "ibm,plb-pciex-460ex", "ibm,plb-pciex";
 			primary;
-			port = <0>; /* port number */
-			reg = <d 00000000 20000000	/* Config space access */
-			       c 08010000 00001000>;	/* Registers */
-			dcr-reg = <100 020>;
-			sdr-base = <300>;
+			port = <0x0>; /* port number */
+			reg = <0x0000000d 0x00000000 0x20000000	/* Config space access */
+			       0x0000000c 0x08010000 0x00001000>;	/* Registers */
+			dcr-reg = <0x100 0x020>;
+			sdr-base = <0x300>;
 
 			/* Outbound ranges, one memory and one IO,
 			 * later cannot be changed
 			 */
-			ranges = <02000000 0 80000000 0000000e 00000000 0 80000000
-				  01000000 0 00000000 0000000f 80000000 0 00010000>;
+			ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000
+				  0x01000000 0x00000000 0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>;
 
 			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <42000000 0 0 0 0 0 80000000>;
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
 
 			/* This drives busses 40 to 0x7f */
-			bus-range = <40 7f>;
+			bus-range = <0x40 0x7f>;
 
 			/* Legacy interrupts (note the weird polarity, the bridge seems
 			 * to invert PCIe legacy interrupts).
@@ -387,12 +389,12 @@
 			 * below are basically de-swizzled numbers.
 			 * The real slot is on idsel 0, so the swizzling is 1:1
 			 */
-			interrupt-map-mask = <0000 0 0 7>;
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
 			interrupt-map = <
-				0000 0 0 1 &UIC3 c 4 /* swizzled int A */
-				0000 0 0 2 &UIC3 d 4 /* swizzled int B */
-				0000 0 0 3 &UIC3 e 4 /* swizzled int C */
-				0000 0 0 4 &UIC3 f 4 /* swizzled int D */>;
+				0x0 0x0 0x0 0x1 &UIC3 0xc 0x4 /* swizzled int A */
+				0x0 0x0 0x0 0x2 &UIC3 0xd 0x4 /* swizzled int B */
+				0x0 0x0 0x0 0x3 &UIC3 0xe 0x4 /* swizzled int C */
+				0x0 0x0 0x0 0x4 &UIC3 0xf 0x4 /* swizzled int D */>;
 		};
 
 		PCIE1: pciex@d20000000 {
@@ -402,23 +404,23 @@
 			#address-cells = <3>;
 			compatible = "ibm,plb-pciex-460ex", "ibm,plb-pciex";
 			primary;
-			port = <1>; /* port number */
-			reg = <d 20000000 20000000	/* Config space access */
-			       c 08011000 00001000>;	/* Registers */
-			dcr-reg = <120 020>;
-			sdr-base = <340>;
+			port = <0x1>; /* port number */
+			reg = <0x0000000d 0x20000000 0x20000000	/* Config space access */
+			       0x0000000c 0x08011000 0x00001000>;	/* Registers */
+			dcr-reg = <0x120 0x020>;
+			sdr-base = <0x340>;
 
 			/* Outbound ranges, one memory and one IO,
 			 * later cannot be changed
 			 */
-			ranges = <02000000 0 80000000 0000000e 80000000 0 80000000
-				  01000000 0 00000000 0000000f 80010000 0 00010000>;
+			ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000
+				  0x01000000 0x00000000 0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>;
 
 			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <42000000 0 0 0 0 0 80000000>;
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
 
 			/* This drives busses 80 to 0xbf */
-			bus-range = <80 bf>;
+			bus-range = <0x80 0xbf>;
 
 			/* Legacy interrupts (note the weird polarity, the bridge seems
 			 * to invert PCIe legacy interrupts).
@@ -428,12 +430,12 @@
 			 * below are basically de-swizzled numbers.
 			 * The real slot is on idsel 0, so the swizzling is 1:1
 			 */
-			interrupt-map-mask = <0000 0 0 7>;
+			interrupt-map-mask = <0x0 0x0 0x0 0x7>;
 			interrupt-map = <
-				0000 0 0 1 &UIC3 10 4 /* swizzled int A */
-				0000 0 0 2 &UIC3 11 4 /* swizzled int B */
-				0000 0 0 3 &UIC3 12 4 /* swizzled int C */
-				0000 0 0 4 &UIC3 13 4 /* swizzled int D */>;
+				0x0 0x0 0x0 0x1 &UIC3 0x10 0x4 /* swizzled int A */
+				0x0 0x0 0x0 0x2 &UIC3 0x11 0x4 /* swizzled int B */
+				0x0 0x0 0x0 0x3 &UIC3 0x12 0x4 /* swizzled int C */
+				0x0 0x0 0x0 0x4 &UIC3 0x13 0x4 /* swizzled int D */>;
 		};
 	};
 };

arch/powerpc/boot/dts/ebony.dts

@@ -11,12 +11,14 @@
  * any warranty of any kind, whether express or implied.
  */
 
+/dts-v1/;
+
 / {
 	#address-cells = <2>;
 	#size-cells = <1>;
 	model = "ibm,ebony";
 	compatible = "ibm,ebony";
-	dcr-parent = <&/cpus/cpu@0>;
+	dcr-parent = <&{/cpus/cpu@0}>;
 
 	aliases {
 		ethernet0 = &EMAC0;
@@ -32,13 +34,13 @@
 		cpu@0 {
 			device_type = "cpu";
 			model = "PowerPC,440GP";
-			reg = <0>;
+			reg = <0x00000000>;
 			clock-frequency = <0>; // Filled in by zImage
 			timebase-frequency = <0>; // Filled in by zImage
-			i-cache-line-size = <20>;
-			d-cache-line-size = <20>;
-			i-cache-size = <8000>; /* 32 kB */
-			d-cache-size = <8000>; /* 32 kB */
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <32768>; /* 32 kB */
+			d-cache-size = <32768>; /* 32 kB */
 			dcr-controller;
 			dcr-access-method = "native";
 		};
@@ -46,14 +48,14 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0 0 0>; // Filled in by zImage
+		reg = <0x00000000 0x00000000 0x00000000>; // Filled in by zImage
 	};
 
 	UIC0: interrupt-controller0 {
 		compatible = "ibm,uic-440gp", "ibm,uic";
 		interrupt-controller;
 		cell-index = <0>;
-		dcr-reg = <0c0 009>;
+		dcr-reg = <0x0c0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
@@ -64,17 +66,17 @@
 		compatible = "ibm,uic-440gp", "ibm,uic";
 		interrupt-controller;
 		cell-index = <1>;
-		dcr-reg = <0d0 009>;
+		dcr-reg = <0x0d0 0x009>;
 		#address-cells = <0>;
 		#size-cells = <0>;
 		#interrupt-cells = <2>;
-		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */
 		interrupt-parent = <&UIC0>;
 	};
 
 	CPC0: cpc {
 		compatible = "ibm,cpc-440gp";
-		dcr-reg = <0b0 003 0e0 010>;
+		dcr-reg = <0x0b0 0x003 0x0e0 0x010>;
 		// FIXME: anything else?
 	};
 
@@ -87,37 +89,37 @@
 
 		SDRAM0: memory-controller {
 			compatible = "ibm,sdram-440gp";
-			dcr-reg = <010 2>;
+			dcr-reg = <0x010 0x002>;
 			// FIXME: anything else?
 		};
 
 		SRAM0: sram {
 			compatible = "ibm,sram-440gp";
-			dcr-reg = <020 8 00a 1>;
+			dcr-reg = <0x020 0x008 0x00a 0x001>;
 		};
 
 		DMA0: dma {
 			// FIXME: ???
 			compatible = "ibm,dma-440gp";
-			dcr-reg = <100 027>;
+			dcr-reg = <0x100 0x027>;
 		};
 
 		MAL0: mcmal {
 			compatible = "ibm,mcmal-440gp", "ibm,mcmal";
-			dcr-reg = <180 62>;
+			dcr-reg = <0x180 0x062>;
 			num-tx-chans = <4>;
 			num-rx-chans = <4>;
 			interrupt-parent = <&MAL0>;
-			interrupts = <0 1 2 3 4>;
+			interrupts = <0x0 0x1 0x2 0x3 0x4>;
 			#interrupt-cells = <1>;
 			#address-cells = <0>;
 			#size-cells = <0>;
-			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
-					 /*RXEOB*/ 1 &UIC0 b 4
-					 /*SERR*/  2 &UIC1 0 4
-					 /*TXDE*/  3 &UIC1 1 4
-					 /*RXDE*/  4 &UIC1 2 4>;
-			interrupt-map-mask = <ffffffff>;
+			interrupt-map = </*TXEOB*/ 0x0 &UIC0 0xa 0x4
+					 /*RXEOB*/ 0x1 &UIC0 0xb 0x4
+					 /*SERR*/  0x2 &UIC1 0x0 0x4
+					 /*TXDE*/  0x3 &UIC1 0x1 0x4
+					 /*RXDE*/  0x4 &UIC1 0x2 0x4>;
+			interrupt-map-mask = <0xffffffff>;
 		};
 
 		POB0: opb {
@@ -126,34 +128,34 @@
 			#size-cells = <1>;
 			/* Wish there was a nicer way of specifying a full 32-bit
 			   range */
-			ranges = <00000000 1 00000000 80000000
-				  80000000 1 80000000 80000000>;
-			dcr-reg = <090 00b>;
+			ranges = <0x00000000 0x00000001 0x00000000 0x80000000
+				  0x80000000 0x00000001 0x80000000 0x80000000>;
+			dcr-reg = <0x090 0x00b>;
 			interrupt-parent = <&UIC1>;
-			interrupts = <7 4>;
+			interrupts = <0x7 0x4>;
 			clock-frequency = <0>; // Filled in by zImage
 
 			EBC0: ebc {
 				compatible = "ibm,ebc-440gp", "ibm,ebc";
-				dcr-reg = <012 2>;
+				dcr-reg = <0x012 0x002>;
 				#address-cells = <2>;
 				#size-cells = <1>;
 				clock-frequency = <0>; // Filled in by zImage
 				// ranges property is supplied by zImage
 				// based on firmware's configuration of the
 				// EBC bridge
-				interrupts = <5 4>;
+				interrupts = <0x5 0x4>;
 				interrupt-parent = <&UIC1>;
 
 				small-flash@0,80000 {
 					compatible = "jedec-flash";
 					bank-width = <1>;
-					reg = <0 80000 80000>;
+					reg = <0x00000000 0x00080000 0x00080000>;
 					#address-cells = <1>;
 					#size-cells = <1>;
 					partition@0 {
 						label = "OpenBIOS";
-						reg = <0 80000>;
+						reg = <0x00000000 0x00080000>;
 						read-only;
 					};
 				};
@@ -161,101 +163,101 @@
 				nvram@1,0 {
 					/* NVRAM & RTC */
 					compatible = "ds1743-nvram";
-					#bytes = <2000>;
-					reg = <1 0 2000>;
+					#bytes = <0x2000>;
+					reg = <0x00000001 0x00000000 0x00002000>;
 				};
 
 				large-flash@2,0 {
 					compatible = "jedec-flash";
 					bank-width = <1>;
-					reg = <2 0 400000>;
+					reg = <0x00000002 0x00000000 0x00400000>;
 					#address-cells = <1>;
 					#size-cells = <1>;
 					partition@0 {
 						label = "fs";
-						reg = <0 380000>;
+						reg = <0x00000000 0x00380000>;
 					};
 					partition@380000 {
 						label = "firmware";
-						reg = <380000 80000>;
+						reg = <0x00380000 0x00080000>;
 					};
 				};
 
 				ir@3,0 {
-					reg = <3 0 10>;
+					reg = <0x00000003 0x00000000 0x00000010>;
 				};
 
 				fpga@7,0 {
 					compatible = "Ebony-FPGA";
-					reg = <7 0 10>;
-					virtual-reg = <e8300000>;
+					reg = <0x00000007 0x00000000 0x00000010>;
+					virtual-reg = <0xe8300000>;
 				};
 			};
 
 			UART0: serial@40000200 {
 				device_type = "serial";
 				compatible = "ns16550";
-				reg = <40000200 8>;
-				virtual-reg = <e0000200>;
-				clock-frequency = <A8C000>;
-				current-speed = <2580>;
+				reg = <0x40000200 0x00000008>;
+				virtual-reg = <0xe0000200>;
+				clock-frequency = <11059200>;
+				current-speed = <9600>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <0 4>;
+				interrupts = <0x0 0x4>;
 			};
 
 			UART1: serial@40000300 {
 				device_type = "serial";
 				compatible = "ns16550";
-				reg = <40000300 8>;
-				virtual-reg = <e0000300>;
-				clock-frequency = <A8C000>;
-				current-speed = <2580>;
+				reg = <0x40000300 0x00000008>;
+				virtual-reg = <0xe0000300>;
+				clock-frequency = <11059200>;
+				current-speed = <9600>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <1 4>;
+				interrupts = <0x1 0x4>;
 			};
 
 			IIC0: i2c@40000400 {
 				/* FIXME */
 				compatible = "ibm,iic-440gp", "ibm,iic";
-				reg = <40000400 14>;
+				reg = <0x40000400 0x00000014>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <2 4>;
+				interrupts = <0x2 0x4>;
 			};
 			IIC1: i2c@40000500 {
 				/* FIXME */
 				compatible = "ibm,iic-440gp", "ibm,iic";
-				reg = <40000500 14>;
+				reg = <0x40000500 0x00000014>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <3 4>;
+				interrupts = <0x3 0x4>;
 			};
 
 			GPIO0: gpio@40000700 {
 				/* FIXME */
 				compatible = "ibm,gpio-440gp";
-				reg = <40000700 20>;
+				reg = <0x40000700 0x00000020>;
 			};
 
 			ZMII0: emac-zmii@40000780 {
 				compatible = "ibm,zmii-440gp", "ibm,zmii";
-				reg = <40000780 c>;
+				reg = <0x40000780 0x0000000c>;
 			};
 
 			EMAC0: ethernet@40000800 {
 				device_type = "network";
 				compatible = "ibm,emac-440gp", "ibm,emac";
 				interrupt-parent = <&UIC1>;
-				interrupts = <1c 4 1d 4>;
-				reg = <40000800 70>;
+				interrupts = <0x1c 0x4 0x1d 0x4>;
+				reg = <0x40000800 0x00000070>;
 				local-mac-address = [000000000000]; // Filled in by zImage
 				mal-device = <&MAL0>;
 				mal-tx-channel = <0 1>;
 				mal-rx-channel = <0>;
 				cell-index = <0>;
-				max-frame-size = <5dc>;
-				rx-fifo-size = <1000>;
-				tx-fifo-size = <800>;
+				max-frame-size = <1500>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
 				phy-mode = "rmii";
-				phy-map = <00000001>;
+				phy-map = <0x00000001>;
 				zmii-device = <&ZMII0>;
 				zmii-channel = <0>;
 			};
@@ -263,18 +265,18 @@
 				device_type = "network";
 				compatible = "ibm,emac-440gp", "ibm,emac";
 				interrupt-parent = <&UIC1>;
-				interrupts = <1e 4 1f 4>;
-				reg = <40000900 70>;
+				interrupts = <0x1e 0x4 0x1f 0x4>;
+				reg = <0x40000900 0x00000070>;
 				local-mac-address = [000000000000]; // Filled in by zImage
 				mal-device = <&MAL0>;
 				mal-tx-channel = <2 3>;
 				mal-rx-channel = <1>;
 				cell-index = <1>;
-				max-frame-size = <5dc>;
-				rx-fifo-size = <1000>;
-				tx-fifo-size = <800>;
+				max-frame-size = <1500>;
+				rx-fifo-size = <4096>;
+				tx-fifo-size = <2048>;
 				phy-mode = "rmii";
-				phy-map = <00000001>;
+				phy-map = <0x00000001>;
 				zmii-device = <&ZMII0>;
 				zmii-channel = <1>;
 			};
@@ -282,9 +284,9 @@
 
 			GPT0: gpt@40000a00 {
 				/* FIXME */
-				reg = <40000a00 d4>;
+				reg = <0x40000a00 0x000000d4>;
 				interrupt-parent = <&UIC0>;
-				interrupts = <12 4 13 4 14 4 15 4 16 4>;
+				interrupts = <0x12 0x4 0x13 0x4 0x14 0x4 0x15 0x4 0x16 0x4>;
 			};
 
 		};
@@ -296,35 +298,35 @@
 			#address-cells = <3>;
 			compatible = "ibm,plb440gp-pcix", "ibm,plb-pcix";
 			primary;
-			reg = <2 0ec00000 8	/* Config space access */
-			       0 0 0		/* no IACK cycles */
-			       2 0ed00000 4     /* Special cycles */
-			       2 0ec80000 f0	/* Internal registers */
-			       2 0ec80100 fc>;	/* Internal messaging registers */
+			reg = <0x00000002 0x0ec00000 0x00000008	/* Config space access */
+			       0x00000000 0x00000000 0x00000000		/* no IACK cycles */
+			       0x00000002 0x0ed00000 0x00000004     /* Special cycles */
+			       0x00000002 0x0ec80000 0x000000f0	/* Internal registers */
+			       0x00000002 0x0ec80100 0x000000fc>;	/* Internal messaging registers */
 
 			/* Outbound ranges, one memory and one IO,
 			 * later cannot be changed
 			 */
-			ranges = <02000000 0 80000000 00000003 80000000 0 80000000
-				  01000000 0 00000000 00000002 08000000 0 00010000>;
+			ranges = <0x02000000 0x00000000 0x80000000 0x00000003 0x80000000 0x00000000 0x80000000
+				  0x01000000 0x00000000 0x00000000 0x00000002 0x08000000 0x00000000 0x00010000>;
 
 			/* Inbound 2GB range starting at 0 */
-			dma-ranges = <42000000 0 0 0 0 0 80000000>;
+			dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>;
 
 			/* Ebony has all 4 IRQ pins tied together per slot */
-			interrupt-map-mask = <f800 0 0 0>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x0>;
 			interrupt-map = <
 				/* IDSEL 1 */
-				0800 0 0 0 &UIC0 17 8
+				0x800 0x0 0x0 0x0 &UIC0 0x17 0x8
 
 				/* IDSEL 2 */
-				1000 0 0 0 &UIC0 18 8
+				0x1000 0x0 0x0 0x0 &UIC0 0x18 0x8
 
 				/* IDSEL 3 */
-				1800 0 0 0 &UIC0 19 8
+				0x1800 0x0 0x0 0x0 &UIC0 0x19 0x8
 
 				/* IDSEL 4 */
-				2000 0 0 0 &UIC0 1a 8
+				0x2000 0x0 0x0 0x0 &UIC0 0x1a 0x8
 			>;
 		};
 	};

arch/powerpc/boot/dts/ksi8560.dts

@@ -40,6 +40,7 @@
 			timebase-frequency = <0>;		/* From U-boot */
 			bus-frequency = <0>;			/* From U-boot */
 			clock-frequency = <0>;			/* From U-boot */
+			next-level-cache = <&L2>;
 		};
 	};
 
@@ -58,16 +59,16 @@
 		memory-controller@2000 {
 			compatible = "fsl,8540-memory-controller";
 			reg = <0x2000 0x1000>;
-			interrupt-parent = <&MPIC>;
+			interrupt-parent = <&mpic>;
 			interrupts = <0x12 0x2>;
 		};
 
-		l2-cache-controller@20000 {
+		L2: l2-cache-controller@20000 {
 			compatible = "fsl,8540-l2-cache-controller";
 			reg = <0x20000 0x1000>;
 			cache-line-size = <0x20>;		/* 32 bytes */
 			cache-size = <0x40000>;			/* L2, 256K */
-			interrupt-parent = <&MPIC>;
+			interrupt-parent = <&mpic>;
 			interrupts = <0x10 0x2>;
 		};
 
@@ -78,10 +79,51 @@
 			compatible = "fsl-i2c";
 			reg = <0x3000 0x100>;
 			interrupts = <0x2b 0x2>;
-			interrupt-parent = <&MPIC>;
+			interrupt-parent = <&mpic>;
 			dfsrr;
 		};
 
+		dma@21300 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "fsl,mpc8560-dma", "fsl,eloplus-dma";
+			reg = <0x21300 0x4>;
+			ranges = <0x0 0x21100 0x200>;
+			cell-index = <0>;
+			dma-channel@0 {
+				compatible = "fsl,mpc8560-dma-channel",
+						"fsl,eloplus-dma-channel";
+				reg = <0x0 0x80>;
+				cell-index = <0>;
+				interrupt-parent = <&mpic>;
+				interrupts = <20 2>;
+			};
+			dma-channel@80 {
+				compatible = "fsl,mpc8560-dma-channel",
+						"fsl,eloplus-dma-channel";
+				reg = <0x80 0x80>;
+				cell-index = <1>;
+				interrupt-parent = <&mpic>;
+				interrupts = <21 2>;
+			};
+			dma-channel@100 {
+				compatible = "fsl,mpc8560-dma-channel",
+						"fsl,eloplus-dma-channel";
+				reg = <0x100 0x80>;
+				cell-index = <2>;
+				interrupt-parent = <&mpic>;
+				interrupts = <22 2>;
+			};
+			dma-channel@180 {
+				compatible = "fsl,mpc8560-dma-channel",
+						"fsl,eloplus-dma-channel";
+				reg = <0x180 0x80>;
+				cell-index = <3>;
+				interrupt-parent = <&mpic>;
+				interrupts = <23 2>;
+			};
+		};
+
 		mdio@24520 {					/* For TSECs */
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -89,13 +131,13 @@
 			reg = <0x24520 0x20>;
 
 			PHY1: ethernet-phy@1 {
-				interrupt-parent = <&MPIC>;
+				interrupt-parent = <&mpic>;
 				reg = <0x1>;
 				device_type = "ethernet-phy";
 			};
 
 			PHY2: ethernet-phy@2 {
-				interrupt-parent = <&MPIC>;
+				interrupt-parent = <&mpic>;
 				reg = <0x2>;
 				device_type = "ethernet-phy";
 			};
@@ -109,7 +151,7 @@
 			/* Mac address filled in by bootwrapper */
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
-			interrupt-parent = <&MPIC>;
+			interrupt-parent = <&mpic>;
 			phy-handle = <&PHY1>;
 		};
 
@@ -121,11 +163,11 @@
 			/* Mac address filled in by bootwrapper */
 			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
-			interrupt-parent = <&MPIC>;
+			interrupt-parent = <&mpic>;
 			phy-handle = <&PHY2>;
 		};
 
-		MPIC: pic@40000 {
+		mpic: pic@40000 {
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
@@ -164,7 +206,7 @@
 				#interrupt-cells = <2>;
 				interrupt-controller;
 				interrupts = <0x2e 0x2>;
-				interrupt-parent = <&MPIC>;
+				interrupt-parent = <&mpic>;
 				reg = <0x90c00 0x80>;
 				compatible = "fsl,mpc8560-cpm-pic", "fsl,cpm2-pic";
 			};
@@ -202,7 +244,7 @@
 				fsl,mdc-pin = <25>;
 
 				PHY0: ethernet-phy@0 {
-					interrupt-parent = <&MPIC>;
+					interrupt-parent = <&mpic>;
 					reg = <0x0>;
 					device_type = "ethernet-phy";
 				};

arch/powerpc/boot/dts/mpc7448hpc2.dts

@@ -124,14 +124,12 @@
 		};
 
 	  	mpic: pic@7400 {
-			clock-frequency = <0>;
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <2>;
 			reg = <0x7400 0x400>;
 			compatible = "chrp,open-pic";
 			device_type = "open-pic";
-                       	big-endian;
 		};
 		pci@1000 {
 			compatible = "tsi108-pci";

arch/powerpc/boot/dts/mpc8272ads.dts

@@ -217,6 +217,17 @@
 				linux,network-index = <1>;
 				fsl,cpm-command = <0x16200300>;
 			};
+
+			i2c@11860 {
+				compatible = "fsl,mpc8272-i2c",
+					     "fsl,cpm2-i2c";
+				reg = <0x11860 0x20 0x8afc 0x2>;
+				interrupts = <1 8>;
+				interrupt-parent = <&PIC>;
+				fsl,cpm-command = <0x29600000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 
 		PIC: interrupt-controller@10c00 {
@@ -226,22 +237,15 @@
 			compatible = "fsl,mpc8272-pic", "fsl,cpm2-pic";
 		};
 
-/* May need to remove if on a part without crypto engine */
 		crypto@30000 {
-			device_type = "crypto";
-			model = "SEC2";
-			compatible = "fsl,mpc8272-talitos-sec2",
-			             "fsl,talitos-sec2",
-			             "fsl,talitos",
-			             "talitos";
-			reg = <0x30000 0x10000>;
-			interrupts = <11 8>;
+			compatible = "fsl,sec1.0";
+			reg = <0x40000 0x13000>;
+			interrupts = <47 0x8>;
 			interrupt-parent = <&PIC>;
-			num-channels = <4>;
-			channel-fifo-len = <24>;
-			exec-units-mask = <0x7e>;
-/* desc mask is for rev1.x, we need runtime fixup for >=2.x */
-			descriptor-types-mask = <0x1010ebf>;
+			fsl,num-channels = <4>;
+			fsl,channel-fifo-len = <24>;
+			fsl,exec-units-mask = <0x7e>;
+			fsl,descriptor-types-mask = <0x1010415>;
 		};
 	};
 

arch/powerpc/boot/dts/mpc866ads.dts

@@ -171,6 +171,17 @@
 				fsl,cpm-command = <0000>;
 				linux,network-index = <1>;
 			};
+
+			i2c@860 {
+				compatible = "fsl,mpc866-i2c",
+					     "fsl,cpm1-i2c";
+				reg = <0x860 0x20 0x3c80 0x30>;
+				interrupts = <16>;
+				interrupt-parent = <&CPM_PIC>;
+				fsl,cpm-command = <0x10>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
 		};
 	};
 

arch/powerpc/boot/dts/storcenter.dts

@@ -95,6 +95,7 @@
 
 		mpic: interrupt-controller@40000 {
 			#interrupt-cells = <2>;
+			#address-cells = <0>;
 			device_type = "open-pic";
 			compatible = "chrp,open-pic";
 			interrupt-controller;