net: dsa: microchip: prepare PHY for proper advertisement

Prepare PHY for proper advertisement as sometimes the PHY in the switch
has its own problems even though it may share the PHY id from regular PHY
but the fixes in the PHY driver do not apply.
Signed-off-by: NTristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/dsa/microchip/ksz9477.c

@@ -2,7 +2,7 @@
 /*
  * Microchip KSZ9477 switch driver main logic
  *
- * Copyright (C) 2017-2018 Microchip Technology Inc.
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
  */
 
 #include <linux/delay.h>
@@ -966,6 +966,16 @@ static void ksz9477_port_mirror_del(struct dsa_switch *ds, int port,
 			     PORT_MIRROR_SNIFFER, false);
 }
 
+static void ksz9477_phy_setup(struct ksz_device *dev, int port,
+			      struct phy_device *phy)
+{
+	if (port < dev->phy_port_cnt) {
+		/* The MAC actually cannot run in 1000 half-duplex mode. */
+		phy_remove_link_mode(phy,
+				     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+	}
+}
+
 static void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 {
 	u8 data8;
@@ -1299,6 +1309,7 @@ static const struct ksz_dev_ops ksz9477_dev_ops = {
 	.get_port_addr = ksz9477_get_port_addr,
 	.cfg_port_member = ksz9477_cfg_port_member,
 	.flush_dyn_mac_table = ksz9477_flush_dyn_mac_table,
+	.phy_setup = ksz9477_phy_setup,
 	.port_setup = ksz9477_port_setup,
 	.shutdown = ksz9477_reset_switch,
 	.detect = ksz9477_switch_detect,

drivers/net/dsa/microchip/ksz_common.c

@@ -2,7 +2,7 @@
 /*
  * Microchip switch driver main logic
  *
- * Copyright (C) 2017-2018 Microchip Technology Inc.
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
  */
 
 #include <linux/delay.h>
@@ -238,6 +238,7 @@ int ksz_enable_port(struct dsa_switch *ds, int port, struct phy_device *phy)
 
 	/* setup slave port */
 	dev->dev_ops->port_setup(dev, port, false);
+	dev->dev_ops->phy_setup(dev, port, phy);
 
 	/* port_stp_state_set() will be called after to enable the port so
 	 * there is no need to do anything.

drivers/net/dsa/microchip/ksz_priv.h

@@ -2,7 +2,7 @@
  *
  * Microchip KSZ series switch common definitions
  *
- * Copyright (C) 2017-2018 Microchip Technology Inc.
+ * Copyright (C) 2017-2019 Microchip Technology Inc.
  */
 
 #ifndef __KSZ_PRIV_H
@@ -137,6 +137,8 @@ struct ksz_dev_ops {
 	u32 (*get_port_addr)(int port, int offset);
 	void (*cfg_port_member)(struct ksz_device *dev, int port, u8 member);
 	void (*flush_dyn_mac_table)(struct ksz_device *dev, int port);
+	void (*phy_setup)(struct ksz_device *dev, int port,
+			  struct phy_device *phy);
 	void (*port_setup)(struct ksz_device *dev, int port, bool cpu_port);
 	void (*r_phy)(struct ksz_device *dev, u16 phy, u16 reg, u16 *val);
 	void (*w_phy)(struct ksz_device *dev, u16 phy, u16 reg, u16 val);