提交 402a917a 编写于 作者: L Linus Torvalds

Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5405/1: ep93xx: remove unused gesbc9312.h header
  [ARM] 5404/1: Fix condition in arm_elf_read_implies_exec() to set READ_IMPLIES_EXEC
  [ARM] omap: fix clock reparenting in omap2_clk_set_parent()
  [ARM] 5403/1: pxa25x_ep_fifo_flush() *ep->reg_udccs always set to 0
  [ARM] 5402/1: fix a case of wrap-around in sanity_check_meminfo()
  [ARM] 5401/1: Orion: fix edge triggered GPIO interrupt support
  [ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device controller
  [ARM] 5391/1: AT91: Enable GPIO clocks earlier
  [ARM] 5390/1: AT91: Watchdog fixes
  [ARM] 5398/1: Add Wan ZongShun to MAINTAINERS for W90P910
  [ARM] omap: fix _omap2_clksel_get_src_field()
  [ARM] omap: fix omap2_divisor_to_clksel() error return value
......@@ -692,6 +692,13 @@ M: kernel@wantstofly.org
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
ARM/NUVOTON W90X900 ARM ARCHITECTURE
P: Wan ZongShun
M: mcuos.com@gmail.com
L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
W: http://www.mcuos.com
S: Maintained
ARPD SUPPORT
P: Jonathan Layes
L: netdev@vger.kernel.org
......
......@@ -608,7 +608,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
CONFIG_AT91SAM9_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
#
# USB-based Watchdog Cards
......
......@@ -700,7 +700,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
CONFIG_AT91SAM9_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
#
# USB-based Watchdog Cards
......
......@@ -710,7 +710,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
CONFIG_AT91SAM9_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
#
# USB-based Watchdog Cards
......
......@@ -606,7 +606,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
CONFIG_AT91SAM9_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
#
# Sonics Silicon Backplane
......
......@@ -727,7 +727,7 @@ CONFIG_WATCHDOG_NOWAYOUT=y
# Watchdog Device Drivers
#
# CONFIG_SOFT_WATCHDOG is not set
# CONFIG_AT91SAM9_WATCHDOG is not set
# CONFIG_AT91SAM9X_WATCHDOG is not set
#
# USB-based Watchdog Cards
......
......@@ -74,9 +74,9 @@ EXPORT_SYMBOL(elf_set_personality);
*/
int arm_elf_read_implies_exec(const struct elf32_hdr *x, int executable_stack)
{
if (executable_stack != EXSTACK_ENABLE_X)
if (executable_stack != EXSTACK_DISABLE_X)
return 1;
if (cpu_architecture() <= CPU_ARCH_ARMv6)
if (cpu_architecture() < CPU_ARCH_ARMv6)
return 1;
return 0;
}
......
......@@ -697,7 +697,7 @@ static void __init at91_add_device_rtt(void)
* Watchdog
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
static struct platform_device at91cap9_wdt_device = {
.name = "at91_wdt",
.id = -1,
......
......@@ -643,7 +643,7 @@ static void __init at91_add_device_rtt(void)
* Watchdog
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
static struct platform_device at91sam9260_wdt_device = {
.name = "at91_wdt",
.id = -1,
......
......@@ -621,7 +621,7 @@ static void __init at91_add_device_rtt(void)
* Watchdog
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
static struct platform_device at91sam9261_wdt_device = {
.name = "at91_wdt",
.id = -1,
......
......@@ -854,7 +854,7 @@ static void __init at91_add_device_rtt(void)
* Watchdog
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
static struct platform_device at91sam9263_wdt_device = {
.name = "at91_wdt",
.id = -1,
......
......@@ -609,7 +609,7 @@ static void __init at91_add_device_rtt(void)
* Watchdog
* -------------------------------------------------------------------- */
#if defined(CONFIG_AT91SAM9_WATCHDOG) || defined(CONFIG_AT91SAM9_WATCHDOG_MODULE)
#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
static struct platform_device at91sam9rl_wdt_device = {
.name = "at91_wdt",
.id = -1,
......
......@@ -490,7 +490,8 @@ postcore_initcall(at91_gpio_debugfs_init);
/*--------------------------------------------------------------------------*/
/* This lock class tells lockdep that GPIO irqs are in a different
/*
* This lock class tells lockdep that GPIO irqs are in a different
* category than their parents, so it won't report false recursion.
*/
static struct lock_class_key gpio_lock_class;
......@@ -509,9 +510,6 @@ void __init at91_gpio_irq_setup(void)
unsigned id = this->id;
unsigned i;
/* enable PIO controller's clock */
clk_enable(this->clock);
__raw_writel(~0, this->regbase + PIO_IDR);
for (i = 0, pin = this->chipbase; i < 32; i++, pin++) {
......@@ -556,7 +554,14 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
data->chipbase = PIN_BASE + i * 32;
data->regbase = data->offset + (void __iomem *)AT91_VA_BASE_SYS;
/* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */
/* enable PIO controller's clock */
clk_enable(data->clock);
/*
* Some processors share peripheral ID between multiple GPIO banks.
* SAM9263 (PIOC, PIOD, PIOE)
* CAP9 (PIOA, PIOB, PIOC, PIOD)
*/
if (last && last->id == data->id)
last->next = data;
}
......
......@@ -93,6 +93,7 @@ struct atmel_nand_data {
u8 enable_pin; /* chip enable */
u8 det_pin; /* card detect */
u8 rdy_pin; /* ready/busy */
u8 rdy_pin_active_low; /* rdy_pin value is inverted */
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */
u8 bus_width_16; /* buswidth is 16 bit */
......
/*
* arch/arm/mach-ep93xx/include/mach/gesbc9312.h
*/
......@@ -10,7 +10,6 @@
#include "platform.h"
#include "gesbc9312.h"
#include "ts72xx.h"
#endif
......@@ -42,7 +42,7 @@ void __init kirkwood_init_irq(void)
writel(0, GPIO_EDGE_CAUSE(32));
for (i = IRQ_KIRKWOOD_GPIO_START; i < NR_IRQS; i++) {
set_irq_chip(i, &orion_gpio_irq_level_chip);
set_irq_chip(i, &orion_gpio_irq_chip);
set_irq_handler(i, handle_level_irq);
irq_desc[i].status |= IRQ_LEVEL;
set_irq_flags(i, IRQF_VALID);
......
......@@ -40,7 +40,7 @@ void __init mv78xx0_init_irq(void)
writel(0, GPIO_EDGE_CAUSE(0));
for (i = IRQ_MV78XX0_GPIO_START; i < NR_IRQS; i++) {
set_irq_chip(i, &orion_gpio_irq_level_chip);
set_irq_chip(i, &orion_gpio_irq_chip);
set_irq_handler(i, handle_level_irq);
irq_desc[i].status |= IRQ_LEVEL;
set_irq_flags(i, IRQF_VALID);
......
......@@ -565,7 +565,7 @@ u32 omap2_clksel_to_divisor(struct clk *clk, u32 field_val)
*
* Given a struct clk of a rate-selectable clksel clock, and a clock divisor,
* find the corresponding register field value. The return register value is
* the value before left-shifting. Returns 0xffffffff on error
* the value before left-shifting. Returns ~0 on error
*/
u32 omap2_divisor_to_clksel(struct clk *clk, u32 div)
{
......@@ -577,7 +577,7 @@ u32 omap2_divisor_to_clksel(struct clk *clk, u32 div)
clks = omap2_get_clksel_by_parent(clk, clk->parent);
if (clks == NULL)
return 0;
return ~0;
for (clkr = clks->rates; clkr->div; clkr++) {
if ((clkr->flags & cpu_mask) && (clkr->div == div))
......@@ -588,7 +588,7 @@ u32 omap2_divisor_to_clksel(struct clk *clk, u32 div)
printk(KERN_ERR "clock: Could not find divisor %d for "
"clock %s parent %s\n", div, clk->name,
clk->parent->name);
return 0;
return ~0;
}
return clkr->val;
......@@ -708,7 +708,7 @@ static u32 omap2_clksel_get_src_field(void __iomem **src_addr,
return 0;
for (clkr = clks->rates; clkr->div; clkr++) {
if (clkr->flags & (cpu_mask | DEFAULT_RATE))
if (clkr->flags & cpu_mask && clkr->flags & DEFAULT_RATE)
break; /* Found the default rate for this platform */
}
......@@ -746,7 +746,7 @@ int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent)
return -EINVAL;
if (clk->usecount > 0)
_omap2_clk_disable(clk);
omap2_clk_disable(clk);
/* Set new source value (previous dividers if any in effect) */
reg_val = __raw_readl(src_addr) & ~field_mask;
......@@ -759,11 +759,11 @@ int omap2_clk_set_parent(struct clk *clk, struct clk *new_parent)
wmb();
}
if (clk->usecount > 0)
_omap2_clk_enable(clk);
clk->parent = new_parent;
if (clk->usecount > 0)
omap2_clk_enable(clk);
/* CLKSEL clocks follow their parents' rates, divided by a divisor */
clk->rate = new_parent->rate;
......
......@@ -44,7 +44,7 @@ void __init orion5x_init_irq(void)
* User can use set_type() if he wants to use edge types handlers.
*/
for (i = IRQ_ORION5X_GPIO_START; i < NR_IRQS; i++) {
set_irq_chip(i, &orion_gpio_irq_level_chip);
set_irq_chip(i, &orion_gpio_irq_chip);
set_irq_handler(i, handle_level_irq);
irq_desc[i].status |= IRQ_LEVEL;
set_irq_flags(i, IRQF_VALID);
......
......@@ -693,7 +693,8 @@ static void __init sanity_check_meminfo(void)
* Check whether this memory bank would entirely overlap
* the vmalloc area.
*/
if (__va(bank->start) >= VMALLOC_MIN) {
if (__va(bank->start) >= VMALLOC_MIN ||
__va(bank->start) < PAGE_OFFSET) {
printk(KERN_NOTICE "Ignoring RAM at %.8lx-%.8lx "
"(vmalloc region overlap).\n",
bank->start, bank->start + bank->size - 1);
......
......@@ -265,51 +265,36 @@ EXPORT_SYMBOL(orion_gpio_set_blink);
* polarity LEVEL mask
*
****************************************************************************/
static void gpio_irq_edge_ack(u32 irq)
{
int pin = irq_to_gpio(irq);
writel(~(1 << (pin & 31)), GPIO_EDGE_CAUSE(pin));
}
static void gpio_irq_edge_mask(u32 irq)
{
int pin = irq_to_gpio(irq);
u32 u;
u = readl(GPIO_EDGE_MASK(pin));
u &= ~(1 << (pin & 31));
writel(u, GPIO_EDGE_MASK(pin));
}
static void gpio_irq_edge_unmask(u32 irq)
static void gpio_irq_ack(u32 irq)
{
int pin = irq_to_gpio(irq);
u32 u;
u = readl(GPIO_EDGE_MASK(pin));
u |= 1 << (pin & 31);
writel(u, GPIO_EDGE_MASK(pin));
int type = irq_desc[irq].status & IRQ_TYPE_SENSE_MASK;
if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) {
int pin = irq_to_gpio(irq);
writel(~(1 << (pin & 31)), GPIO_EDGE_CAUSE(pin));
}
}
static void gpio_irq_level_mask(u32 irq)
static void gpio_irq_mask(u32 irq)
{
int pin = irq_to_gpio(irq);
u32 u;
u = readl(GPIO_LEVEL_MASK(pin));
int type = irq_desc[irq].status & IRQ_TYPE_SENSE_MASK;
u32 reg = (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) ?
GPIO_EDGE_MASK(pin) : GPIO_LEVEL_MASK(pin);
u32 u = readl(reg);
u &= ~(1 << (pin & 31));
writel(u, GPIO_LEVEL_MASK(pin));
writel(u, reg);
}
static void gpio_irq_level_unmask(u32 irq)
static void gpio_irq_unmask(u32 irq)
{
int pin = irq_to_gpio(irq);
u32 u;
u = readl(GPIO_LEVEL_MASK(pin));
int type = irq_desc[irq].status & IRQ_TYPE_SENSE_MASK;
u32 reg = (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) ?
GPIO_EDGE_MASK(pin) : GPIO_LEVEL_MASK(pin);
u32 u = readl(reg);
u |= 1 << (pin & 31);
writel(u, GPIO_LEVEL_MASK(pin));
writel(u, reg);
}
static int gpio_irq_set_type(u32 irq, u32 type)
......@@ -331,9 +316,9 @@ static int gpio_irq_set_type(u32 irq, u32 type)
* Set edge/level type.
*/
if (type & (IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING)) {
desc->chip = &orion_gpio_irq_edge_chip;
desc->handle_irq = handle_edge_irq;
} else if (type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) {
desc->chip = &orion_gpio_irq_level_chip;
desc->handle_irq = handle_level_irq;
} else {
printk(KERN_ERR "failed to set irq=%d (type=%d)\n", irq, type);
return -EINVAL;
......@@ -371,19 +356,11 @@ static int gpio_irq_set_type(u32 irq, u32 type)
return 0;
}
struct irq_chip orion_gpio_irq_edge_chip = {
.name = "orion_gpio_irq_edge",
.ack = gpio_irq_edge_ack,
.mask = gpio_irq_edge_mask,
.unmask = gpio_irq_edge_unmask,
.set_type = gpio_irq_set_type,
};
struct irq_chip orion_gpio_irq_level_chip = {
.name = "orion_gpio_irq_level",
.mask = gpio_irq_level_mask,
.mask_ack = gpio_irq_level_mask,
.unmask = gpio_irq_level_unmask,
struct irq_chip orion_gpio_irq_chip = {
.name = "orion_gpio",
.ack = gpio_irq_ack,
.mask = gpio_irq_mask,
.unmask = gpio_irq_unmask,
.set_type = gpio_irq_set_type,
};
......
......@@ -31,8 +31,7 @@ void orion_gpio_set_blink(unsigned pin, int blink);
/*
* GPIO interrupt handling.
*/
extern struct irq_chip orion_gpio_irq_edge_chip;
extern struct irq_chip orion_gpio_irq_level_chip;
extern struct irq_chip orion_gpio_irq_chip;
void orion_gpio_irq_handler(int irqoff);
......
......@@ -116,6 +116,7 @@ struct atmel_nand_data {
int enable_pin; /* chip enable */
int det_pin; /* card detect */
int rdy_pin; /* ready/busy */
u8 rdy_pin_active_low; /* rdy_pin value is inverted */
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */
u8 bus_width_16; /* buswidth is 16 bit */
......
......@@ -139,7 +139,8 @@ static int atmel_nand_device_ready(struct mtd_info *mtd)
struct nand_chip *nand_chip = mtd->priv;
struct atmel_nand_host *host = nand_chip->priv;
return gpio_get_value(host->board->rdy_pin);
return gpio_get_value(host->board->rdy_pin) ^
!!host->board->rdy_pin_active_low;
}
/*
......
......@@ -904,8 +904,8 @@ static void pxa25x_ep_fifo_flush(struct usb_ep *_ep)
/* most IN status is the same, but ISO can't stall */
*ep->reg_udccs = UDCCS_BI_TPC|UDCCS_BI_FTF|UDCCS_BI_TUR
| (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC)
? 0 : UDCCS_BI_SST;
| (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC
? 0 : UDCCS_BI_SST);
}
......
......@@ -107,10 +107,10 @@ static int at91_wdt_close(struct inode *inode, struct file *file)
static int at91_wdt_settimeout(int new_time)
{
/*
* All counting occurs at SLOW_CLOCK / 128 = 0.256 Hz
* All counting occurs at SLOW_CLOCK / 128 = 256 Hz
*
* Since WDV is a 16-bit counter, the maximum period is
* 65536 / 0.256 = 256 seconds.
* 65536 / 256 = 256 seconds.
*/
if ((new_time <= 0) || (new_time > WDT_MAX_TIME))
return -EINVAL;
......
......@@ -18,6 +18,7 @@
#include <linux/errno.h>
#include <linux/fs.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/miscdevice.h>
#include <linux/module.h>
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册