iio: pressure: bmp280: add power management

The PM280 has an internal standby-mode, but to really save power
we should shut the sensor down and disconnect the power. With
the proper .pm hooks we can enable both runtime and system power
management of the sensor. We use the *force callbacks from the
system PM hooks. When the sensor comes back we always reconfigure
it to make sure it is ready to roll as expected.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NJonathan Cameron <jic23@kernel.org>

drivers/iio/pressure/bmp280-core.c

@@ -30,6 +30,7 @@
 #include <linux/interrupt.h>
 #include <linux/irq.h> /* For irq_get_irq_data() */
 #include <linux/completion.h>
+#include <linux/pm_runtime.h>
 
 #include "bmp280.h"
 
@@ -336,6 +337,7 @@ static int bmp280_read_raw(struct iio_dev *indio_dev,
 	int ret;
 	struct bmp280_data *data = iio_priv(indio_dev);
 
+	pm_runtime_get_sync(data->dev);
 	mutex_lock(&data->lock);
 
 	switch (mask) {
@@ -380,6 +382,8 @@ static int bmp280_read_raw(struct iio_dev *indio_dev,
 	}
 
 	mutex_unlock(&data->lock);
+	pm_runtime_mark_last_busy(data->dev);
+	pm_runtime_put_autosuspend(data->dev);
 
 	return ret;
 }
@@ -444,6 +448,7 @@ static int bmp280_write_raw(struct iio_dev *indio_dev,
 
 	switch (mask) {
 	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
+		pm_runtime_get_sync(data->dev);
 		mutex_lock(&data->lock);
 		switch (chan->type) {
 		case IIO_HUMIDITYRELATIVE:
@@ -460,6 +465,8 @@ static int bmp280_write_raw(struct iio_dev *indio_dev,
 			break;
 		}
 		mutex_unlock(&data->lock);
+		pm_runtime_mark_last_busy(data->dev);
+		pm_runtime_put_autosuspend(data->dev);
 		break;
 	default:
 		return -EINVAL;
@@ -1021,12 +1028,29 @@ int bmp280_common_probe(struct device *dev,
 			goto out_disable_vdda;
 	}
 
+	/* Enable runtime PM */
+	pm_runtime_get_noresume(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Set autosuspend to two orders of magnitude larger than the
+	 * start-up time.
+	 */
+	pm_runtime_set_autosuspend_delay(dev, data->start_up_time *100);
+	pm_runtime_use_autosuspend(dev);
+	pm_runtime_put(dev);
+
 	ret = iio_device_register(indio_dev);
 	if (ret)
-		goto out_disable_vdda;
+		goto out_runtime_pm_disable;
+
 
 	return 0;
 
+out_runtime_pm_disable:
+	pm_runtime_get_sync(data->dev);
+	pm_runtime_put_noidle(data->dev);
+	pm_runtime_disable(data->dev);
 out_disable_vdda:
 	regulator_disable(data->vdda);
 out_disable_vddd:
@@ -1041,12 +1065,51 @@ int bmp280_common_remove(struct device *dev)
 	struct bmp280_data *data = iio_priv(indio_dev);
 
 	iio_device_unregister(indio_dev);
+	pm_runtime_get_sync(data->dev);
+	pm_runtime_put_noidle(data->dev);
+	pm_runtime_disable(data->dev);
 	regulator_disable(data->vdda);
 	regulator_disable(data->vddd);
 	return 0;
 }
 EXPORT_SYMBOL(bmp280_common_remove);
 
+#ifdef CONFIG_PM
+static int bmp280_runtime_suspend(struct device *dev)
+{
+	struct bmp280_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regulator_disable(data->vdda);
+	if (ret)
+		return ret;
+	return regulator_disable(data->vddd);
+}
+
+static int bmp280_runtime_resume(struct device *dev)
+{
+	struct bmp280_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = regulator_enable(data->vddd);
+	if (ret)
+		return ret;
+	ret = regulator_enable(data->vdda);
+	if (ret)
+		return ret;
+	msleep(data->start_up_time);
+	return data->chip_info->chip_config(data);
+}
+#endif /* CONFIG_PM */
+
+const struct dev_pm_ops bmp280_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(bmp280_runtime_suspend,
+			   bmp280_runtime_resume, NULL)
+};
+EXPORT_SYMBOL(bmp280_dev_pm_ops);
+
 MODULE_AUTHOR("Vlad Dogaru <vlad.dogaru@intel.com>");
 MODULE_DESCRIPTION("Driver for Bosch Sensortec BMP180/BMP280 pressure and temperature sensor");
 MODULE_LICENSE("GPL v2");

drivers/iio/pressure/bmp280-i2c.c

@@ -78,6 +78,7 @@ static struct i2c_driver bmp280_i2c_driver = {
 		.name	= "bmp280",
 		.acpi_match_table = ACPI_PTR(bmp280_acpi_i2c_match),
 		.of_match_table = of_match_ptr(bmp280_of_i2c_match),
+		.pm = &bmp280_dev_pm_ops,
 	},
 	.probe		= bmp280_i2c_probe,
 	.remove		= bmp280_i2c_remove,

drivers/iio/pressure/bmp280-spi.c

@@ -113,6 +113,7 @@ static struct spi_driver bmp280_spi_driver = {
 	.driver = {
 		.name = "bmp280",
 		.of_match_table = bmp280_of_spi_match,
+		.pm = &bmp280_dev_pm_ops,
 	},
 	.id_table = bmp280_spi_id,
 	.probe = bmp280_spi_probe,

drivers/iio/pressure/bmp280.h

@@ -107,3 +107,6 @@ int bmp280_common_probe(struct device *dev,
 			const char *name,
 			int irq);
 int bmp280_common_remove(struct device *dev);
+
+/* PM ops */
+extern const struct dev_pm_ops bmp280_dev_pm_ops;