serial: imx: implement shadow registers for UCRx and UFCR

This reduces the amount of read accesses to the register space by
shadowing the values for five registers that only change on writing
them. There is a single bit in UCR2 that might change without being
written to it, this is handled accordingly.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/imx.c

@@ -204,6 +204,13 @@ struct imx_port {
 
 	struct mctrl_gpios *gpios;
 
+	/* shadow registers */
+	unsigned int ucr1;
+	unsigned int ucr2;
+	unsigned int ucr3;
+	unsigned int ucr4;
+	unsigned int ufcr;
+
 	/* DMA fields */
 	unsigned int		dma_is_enabled:1;
 	unsigned int		dma_is_rxing:1;
@@ -275,12 +282,56 @@ MODULE_DEVICE_TABLE(of, imx_uart_dt_ids);
 
 static void imx_uart_writel(struct imx_port *sport, u32 val, u32 offset)
 {
+	switch (offset) {
+	case UCR1:
+		sport->ucr1 = val;
+		break;
+	case UCR2:
+		sport->ucr2 = val;
+		break;
+	case UCR3:
+		sport->ucr3 = val;
+		break;
+	case UCR4:
+		sport->ucr4 = val;
+		break;
+	case UFCR:
+		sport->ufcr = val;
+		break;
+	default:
+		break;
+	}
 	writel(val, sport->port.membase + offset);
 }
 
 static u32 imx_uart_readl(struct imx_port *sport, u32 offset)
 {
-	return readl(sport->port.membase + offset);
+	switch (offset) {
+	case UCR1:
+		return sport->ucr1;
+		break;
+	case UCR2:
+		/*
+		 * UCR2_SRST is the only bit in the cached registers that might
+		 * differ from the value that was last written. As it only
+		 * clears after being set, reread conditionally.
+		 */
+		if (sport->ucr2 & UCR2_SRST)
+			sport->ucr2 = readl(sport->port.membase + offset);
+		return sport->ucr2;
+		break;
+	case UCR3:
+		return sport->ucr3;
+		break;
+	case UCR4:
+		return sport->ucr4;
+		break;
+	case UFCR:
+		return sport->ufcr;
+		break;
+	default:
+		return readl(sport->port.membase + offset);
+	}
 }
 
 static inline unsigned uts_reg(struct imx_port *sport)
@@ -2136,6 +2187,13 @@ static int serial_imx_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	/* initialize shadow register values */
+	sport->ucr1 = readl(sport->port.membase + UCR1);
+	sport->ucr2 = readl(sport->port.membase + UCR2);
+	sport->ucr3 = readl(sport->port.membase + UCR3);
+	sport->ucr4 = readl(sport->port.membase + UCR4);
+	sport->ufcr = readl(sport->port.membase + UFCR);
+
 	uart_get_rs485_mode(&pdev->dev, &sport->port.rs485);
 
 	if (sport->port.rs485.flags & SER_RS485_ENABLED &&