Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux

From Cyrille:

"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""

Documentation/devicetree/bindings/mtd/aspeed-smc.txt

+* Aspeed Firmware Memory controller
+* Aspeed SPI Flash Memory Controller
+
+The Firmware Memory Controller in the Aspeed AST2500 SoC supports
+three chip selects, two of which are always of SPI type and the third
+can be SPI or NOR type flash. These bindings only describe SPI.
+
+The two SPI flash memory controllers in the AST2500 each support two
+chip selects.
+
+Required properties:
+  - compatible : Should be one of
+	"aspeed,ast2400-fmc" for the AST2400 Firmware Memory Controller
+	"aspeed,ast2400-spi" for the AST2400 SPI Flash memory Controller
+	"aspeed,ast2500-fmc" for the AST2500 Firmware Memory Controller
+	"aspeed,ast2500-spi" for the AST2500 SPI flash memory controllers
+
+  - reg : the first contains the control register location and length,
+          the second contains the memory window mapping address and length
+  - #address-cells : must be 1 corresponding to chip select child binding
+  - #size-cells : must be 0 corresponding to chip select child binding
+
+Optional properties:
+  - interrupts : Should contain the interrupt for the dma device if an
+    FMC
+
+The child nodes are the SPI flash modules which must have a compatible
+property as specified in bindings/mtd/jedec,spi-nor.txt
+
+Optionally, the child node can contain properties for SPI mode (may be
+ignored):
+  - spi-max-frequency - max frequency of spi bus
+
+
+Example:
+fmc: fmc@1e620000 {
+	compatible = "aspeed,ast2500-fmc";
+	reg = < 0x1e620000 0x94
+		0x20000000 0x02000000 >;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	interrupts = <19>;
+	flash@0 {
+		reg = < 0 >;
+		compatible = "jedec,spi-nor";
+		/* spi-max-frequency = <>; */
+		/* m25p,fast-read; */
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};

Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt

@@ -14,6 +14,8 @@ Required properties:
                  at25df641
                  at26df081a
                  mr25h256
+                 mr25h10
+                 mr25h40
                  mx25l4005a
                  mx25l1606e
                  mx25l6405d

Documentation/devicetree/bindings/mtd/mtk-quadspi.txt

 * Serial NOR flash controller for MTK MT81xx (and similar)
 
 Required properties:
-- compatible: 	  should be "mediatek,mt8173-nor";
+- compatible: 	  The possible values are:
+		  "mediatek,mt2701-nor"
+		  "mediatek,mt7623-nor"
+		  "mediatek,mt8173-nor"
+		  For mt8173, compatible should be "mediatek,mt8173-nor".
+		  For every other SoC, should contain both the SoC-specific compatible string
+		  and "mediatek,mt8173-nor".
 - reg: 		  physical base address and length of the controller's register
 - clocks: 	  the phandle of the clocks needed by the nor controller
 - clock-names: 	  the names of the clocks

Documentation/mtd/intel-spi.txt

+Upgrading BIOS using intel-spi
+------------------------------
+
+Many Intel CPUs like Baytrail and Braswell include SPI serial flash host
+controller which is used to hold BIOS and other platform specific data.
+Since contents of the SPI serial flash is crucial for machine to function,
+it is typically protected by different hardware protection mechanisms to
+avoid accidental (or on purpose) overwrite of the content.
+
+Not all manufacturers protect the SPI serial flash, mainly because it
+allows upgrading the BIOS image directly from an OS.
+
+The intel-spi driver makes it possible to read and write the SPI serial
+flash, if certain protection bits are not set and locked. If it finds
+any of them set, the whole MTD device is made read-only to prevent
+partial overwrites. By default the driver exposes SPI serial flash
+contents as read-only but it can be changed from kernel command line,
+passing "intel-spi.writeable=1".
+
+Please keep in mind that overwriting the BIOS image on SPI serial flash
+might render the machine unbootable and requires special equipment like
+Dediprog to revive. You have been warned!
+
+Below are the steps how to upgrade MinnowBoard MAX BIOS directly from
+Linux.
+
+ 1) Download and extract the latest Minnowboard MAX BIOS SPI image
+    [1]. At the time writing this the latest image is v92.
+
+ 2) Install mtd-utils package [2]. We need this in order to erase the SPI
+    serial flash. Distros like Debian and Fedora have this prepackaged with
+    name "mtd-utils".
+
+ 3) Add "intel-spi.writeable=1" to the kernel command line and reboot
+    the board (you can also reload the driver passing "writeable=1" as
+    module parameter to modprobe).
+
+ 4) Once the board is up and running again, find the right MTD partition
+    (it is named as "BIOS"):
+
+    # cat /proc/mtd
+    dev:    size   erasesize  name
+    mtd0: 00800000 00001000 "BIOS"
+
+    So here it will be /dev/mtd0 but it may vary.
+
+ 5) Make backup of the existing image first:
+
+    # dd if=/dev/mtd0ro of=bios.bak
+    16384+0 records in
+    16384+0 records out
+    8388608 bytes (8.4 MB) copied, 10.0269 s, 837 kB/s
+
+ 6) Verify the backup
+
+    # sha1sum /dev/mtd0ro bios.bak
+    fdbb011920572ca6c991377c4b418a0502668b73  /dev/mtd0ro
+    fdbb011920572ca6c991377c4b418a0502668b73  bios.bak
+
+    The SHA1 sums must match. Otherwise do not continue any further!
+
+ 7) Erase the SPI serial flash. After this step, do not reboot the
+    board! Otherwise it will not start anymore.
+
+    # flash_erase /dev/mtd0 0 0
+    Erasing 4 Kibyte @ 7ff000 -- 100 % complete
+
+ 8) Once completed without errors you can write the new BIOS image:
+
+    # dd if=MNW2MAX1.X64.0092.R01.1605221712.bin of=/dev/mtd0
+
+ 9) Verify that the new content of the SPI serial flash matches the new
+    BIOS image:
+
+    # sha1sum /dev/mtd0ro MNW2MAX1.X64.0092.R01.1605221712.bin
+    9b4df9e4be2057fceec3a5529ec3d950836c87a2  /dev/mtd0ro
+    9b4df9e4be2057fceec3a5529ec3d950836c87a2 MNW2MAX1.X64.0092.R01.1605221712.bin
+
+    The SHA1 sums should match.
+
+ 10) Now you can reboot your board and observe the new BIOS starting up
+     properly.
+
+References
+----------
+
+[1] https://firmware.intel.com/sites/default/files/MinnowBoard.MAX_.X64.92.R01.zip
+[2] http://www.linux-mtd.infradead.org/

drivers/mfd/lpc_ich.c

@@ -56,6 +56,7 @@
  *	document number TBD : Wildcat Point-LP
  *	document number TBD : 9 Series
  *	document number TBD : Lewisburg
+ *	document number TBD : Apollo Lake SoC
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
@@ -83,6 +84,17 @@
 #define ACPIBASE_GCS_OFF	0x3410
 #define ACPIBASE_GCS_END	0x3414
 
+#define SPIBASE_BYT		0x54
+#define SPIBASE_BYT_SZ		512
+#define SPIBASE_BYT_EN		BIT(1)
+
+#define SPIBASE_LPT		0x3800
+#define SPIBASE_LPT_SZ		512
+#define BCR			0xdc
+#define BCR_WPD			BIT(0)
+
+#define SPIBASE_APL_SZ		4096
+
 #define GPIOBASE_ICH0		0x58
 #define GPIOCTRL_ICH0		0x5C
 #define GPIOBASE_ICH6		0x48
@@ -133,6 +145,12 @@ static struct resource gpio_ich_res[] = {
 	},
 };
 
+static struct resource intel_spi_res[] = {
+	{
+		.flags = IORESOURCE_MEM,
+	}
+};
+
 static struct mfd_cell lpc_ich_wdt_cell = {
 	.name = "iTCO_wdt",
 	.num_resources = ARRAY_SIZE(wdt_ich_res),
@@ -147,6 +165,14 @@ static struct mfd_cell lpc_ich_gpio_cell = {
 	.ignore_resource_conflicts = true,
 };
 
+
+static struct mfd_cell lpc_ich_spi_cell = {
+	.name = "intel-spi",
+	.num_resources = ARRAY_SIZE(intel_spi_res),
+	.resources = intel_spi_res,
+	.ignore_resource_conflicts = true,
+};
+
 /* chipset related info */
 enum lpc_chipsets {
 	LPC_ICH = 0,	/* ICH */
@@ -216,6 +242,7 @@ enum lpc_chipsets {
 	LPC_BRASWELL,	/* Braswell SoC */
 	LPC_LEWISBURG,	/* Lewisburg */
 	LPC_9S,		/* 9 Series */
+	LPC_APL,	/* Apollo Lake SoC */
 };
 
 static struct lpc_ich_info lpc_chipset_info[] = {
@@ -494,10 +521,12 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 		.name = "Lynx Point",
 		.iTCO_version = 2,
 		.gpio_version = ICH_V5_GPIO,
+		.spi_type = INTEL_SPI_LPT,
 	},
 	[LPC_LPT_LP] = {
 		.name = "Lynx Point_LP",
 		.iTCO_version = 2,
+		.spi_type = INTEL_SPI_LPT,
 	},
 	[LPC_WBG] = {
 		.name = "Wellsburg",
@@ -511,6 +540,7 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 	[LPC_BAYTRAIL] = {
 		.name = "Bay Trail SoC",
 		.iTCO_version = 3,
+		.spi_type = INTEL_SPI_BYT,
 	},
 	[LPC_COLETO] = {
 		.name = "Coleto Creek",
@@ -519,10 +549,12 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 	[LPC_WPT_LP] = {
 		.name = "Wildcat Point_LP",
 		.iTCO_version = 2,
+		.spi_type = INTEL_SPI_LPT,
 	},
 	[LPC_BRASWELL] = {
 		.name = "Braswell SoC",
 		.iTCO_version = 3,
+		.spi_type = INTEL_SPI_BYT,
 	},
 	[LPC_LEWISBURG] = {
 		.name = "Lewisburg",
@@ -533,6 +565,10 @@ static struct lpc_ich_info lpc_chipset_info[] = {
 		.iTCO_version = 2,
 		.gpio_version = ICH_V5_GPIO,
 	},
+	[LPC_APL] = {
+		.name = "Apollo Lake SoC",
+		.spi_type = INTEL_SPI_BXT,
+	},
 };
 
 /*
@@ -681,6 +717,7 @@ static const struct pci_device_id lpc_ich_ids[] = {
 	{ PCI_VDEVICE(INTEL, 0x3b14), LPC_3420},
 	{ PCI_VDEVICE(INTEL, 0x3b16), LPC_3450},
 	{ PCI_VDEVICE(INTEL, 0x5031), LPC_EP80579},
+	{ PCI_VDEVICE(INTEL, 0x5ae8), LPC_APL},
 	{ PCI_VDEVICE(INTEL, 0x8c40), LPC_LPT},
 	{ PCI_VDEVICE(INTEL, 0x8c41), LPC_LPT},
 	{ PCI_VDEVICE(INTEL, 0x8c42), LPC_LPT},
@@ -1056,6 +1093,94 @@ static int lpc_ich_init_wdt(struct pci_dev *dev)
 	return ret;
 }
 
+static int lpc_ich_init_spi(struct pci_dev *dev)
+{
+	struct lpc_ich_priv *priv = pci_get_drvdata(dev);
+	struct resource *res = &intel_spi_res[0];
+	struct intel_spi_boardinfo *info;
+	u32 spi_base, rcba, bcr;
+
+	info = devm_kzalloc(&dev->dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->type = lpc_chipset_info[priv->chipset].spi_type;
+
+	switch (info->type) {
+	case INTEL_SPI_BYT:
+		pci_read_config_dword(dev, SPIBASE_BYT, &spi_base);
+		if (spi_base & SPIBASE_BYT_EN) {
+			res->start = spi_base & ~(SPIBASE_BYT_SZ - 1);
+			res->end = res->start + SPIBASE_BYT_SZ - 1;
+		}
+		break;
+
+	case INTEL_SPI_LPT:
+		pci_read_config_dword(dev, RCBABASE, &rcba);
+		if (rcba & 1) {
+			spi_base = round_down(rcba, SPIBASE_LPT_SZ);
+			res->start = spi_base + SPIBASE_LPT;
+			res->end = res->start + SPIBASE_LPT_SZ - 1;
+
+			/*
+			 * Try to make the flash chip writeable now by
+			 * setting BCR_WPD. It it fails we tell the driver
+			 * that it can only read the chip.
+			 */
+			pci_read_config_dword(dev, BCR, &bcr);
+			if (!(bcr & BCR_WPD)) {
+				bcr |= BCR_WPD;
+				pci_write_config_dword(dev, BCR, bcr);
+				pci_read_config_dword(dev, BCR, &bcr);
+			}
+			info->writeable = !!(bcr & BCR_WPD);
+		}
+		break;
+
+	case INTEL_SPI_BXT: {
+		unsigned int p2sb = PCI_DEVFN(13, 0);
+		unsigned int spi = PCI_DEVFN(13, 2);
+		struct pci_bus *bus = dev->bus;
+
+		/*
+		 * The P2SB is hidden by BIOS and we need to unhide it in
+		 * order to read BAR of the SPI flash device. Once that is
+		 * done we hide it again.
+		 */
+		pci_bus_write_config_byte(bus, p2sb, 0xe1, 0x0);
+		pci_bus_read_config_dword(bus, spi, PCI_BASE_ADDRESS_0,
+					  &spi_base);
+		if (spi_base != ~0) {
+			res->start = spi_base & 0xfffffff0;
+			res->end = res->start + SPIBASE_APL_SZ - 1;
+
+			pci_bus_read_config_dword(bus, spi, BCR, &bcr);
+			if (!(bcr & BCR_WPD)) {
+				bcr |= BCR_WPD;
+				pci_bus_write_config_dword(bus, spi, BCR, bcr);
+				pci_bus_read_config_dword(bus, spi, BCR, &bcr);
+			}
+			info->writeable = !!(bcr & BCR_WPD);
+		}
+
+		pci_bus_write_config_byte(bus, p2sb, 0xe1, 0x1);
+		break;
+	}
+
+	default:
+		return -EINVAL;
+	}
+
+	if (!res->start)
+		return -ENODEV;
+
+	lpc_ich_spi_cell.platform_data = info;
+	lpc_ich_spi_cell.pdata_size = sizeof(*info);
+
+	return mfd_add_devices(&dev->dev, PLATFORM_DEVID_NONE,
+			       &lpc_ich_spi_cell, 1, NULL, 0, NULL);
+}
+
 static int lpc_ich_probe(struct pci_dev *dev,
 				const struct pci_device_id *id)
 {
@@ -1099,6 +1224,12 @@ static int lpc_ich_probe(struct pci_dev *dev,
 			cell_added = true;
 	}
 
+	if (lpc_chipset_info[priv->chipset].spi_type) {
+		ret = lpc_ich_init_spi(dev);
+		if (!ret)
+			cell_added = true;
+	}
+
 	/*
 	 * We only care if at least one or none of the cells registered
 	 * successfully.

drivers/mtd/devices/m25p80.c

@@ -172,7 +172,8 @@ static ssize_t m25p80_read(struct spi_nor *nor, loff_t from, size_t len,
 
 	t[1].rx_buf = buf;
 	t[1].rx_nbits = m25p80_rx_nbits(nor);
-	t[1].len = min(len, spi_max_transfer_size(spi));
+	t[1].len = min3(len, spi_max_transfer_size(spi),
+			spi_max_message_size(spi) - t[0].len);
 	spi_message_add_tail(&t[1], &m);
 
 	ret = spi_sync(spi, &m);
@@ -288,7 +289,6 @@ static const struct spi_device_id m25p_ids[] = {
 	 * should be kept for backward compatibility.
 	 */
 	{"at25df321a"},	{"at25df641"},	{"at26df081a"},
-	{"mr25h256"},
 	{"mx25l4005a"},	{"mx25l1606e"},	{"mx25l6405d"},	{"mx25l12805d"},
 	{"mx25l25635e"},{"mx66l51235l"},
 	{"n25q064"},	{"n25q128a11"},	{"n25q128a13"},	{"n25q512a"},
@@ -305,6 +305,11 @@ static const struct spi_device_id m25p_ids[] = {
 	{"m25p40-nonjedec"},	{"m25p80-nonjedec"},	{"m25p16-nonjedec"},
 	{"m25p32-nonjedec"},	{"m25p64-nonjedec"},	{"m25p128-nonjedec"},
 
+	/* Everspin MRAMs (non-JEDEC) */
+	{ "mr25h256" }, /* 256 Kib, 40 MHz */
+	{ "mr25h10" },  /*   1 Mib, 40 MHz */
+	{ "mr25h40" },  /*   4 Mib, 40 MHz */
+
 	{ },
 };
 MODULE_DEVICE_TABLE(spi, m25p_ids);

drivers/mtd/devices/serial_flash_cmds.h

@@ -18,19 +18,12 @@
 #define SPINOR_OP_RDVCR		0x85
 
 /* JEDEC Standard - Serial Flash Discoverable Parmeters (SFDP) Commands */
-#define SPINOR_OP_READ_1_2_2	0xbb	/* DUAL I/O READ */
-#define SPINOR_OP_READ_1_4_4	0xeb	/* QUAD I/O READ */
-
 #define SPINOR_OP_WRITE		0x02	/* PAGE PROGRAM */
 #define SPINOR_OP_WRITE_1_1_2	0xa2	/* DUAL INPUT PROGRAM */
 #define SPINOR_OP_WRITE_1_2_2	0xd2	/* DUAL INPUT EXT PROGRAM */
 #define SPINOR_OP_WRITE_1_1_4	0x32	/* QUAD INPUT PROGRAM */
 #define SPINOR_OP_WRITE_1_4_4	0x12	/* QUAD INPUT EXT PROGRAM */
 
-/* READ commands with 32-bit addressing */
-#define SPINOR_OP_READ4_1_2_2	0xbc
-#define SPINOR_OP_READ4_1_4_4	0xec
-
 /* Configuration flags */
 #define FLASH_FLAG_SINGLE	0x000000ff
 #define FLASH_FLAG_READ_WRITE	0x00000001

drivers/mtd/devices/st_spi_fsm.c

@@ -507,13 +507,13 @@ static struct seq_rw_config n25q_read3_configs[] = {
  *	- 'FAST' variants configured for 8 dummy cycles (see note above.)
  */
 static struct seq_rw_config n25q_read4_configs[] = {
-	{FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ4_1_4_4,	0, 4, 4, 0x00, 0, 8},
-	{FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ4_1_1_4,	0, 1, 4, 0x00, 0, 8},
-	{FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ4_1_2_2,	0, 2, 2, 0x00, 0, 8},
-	{FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ4_1_1_2,	0, 1, 2, 0x00, 0, 8},
-	{FLASH_FLAG_READ_FAST,	SPINOR_OP_READ4_FAST,	0, 1, 1, 0x00, 0, 8},
-	{FLASH_FLAG_READ_WRITE, SPINOR_OP_READ4,	0, 1, 1, 0x00, 0, 0},
-	{0x00,			0,			0, 0, 0, 0x00, 0, 0},
+	{FLASH_FLAG_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B, 0, 4, 4, 0x00, 0, 8},
+	{FLASH_FLAG_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B, 0, 1, 4, 0x00, 0, 8},
+	{FLASH_FLAG_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B, 0, 2, 2, 0x00, 0, 8},
+	{FLASH_FLAG_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B, 0, 1, 2, 0x00, 0, 8},
+	{FLASH_FLAG_READ_FAST,	SPINOR_OP_READ_FAST_4B,  0, 1, 1, 0x00, 0, 8},
+	{FLASH_FLAG_READ_WRITE, SPINOR_OP_READ_4B,       0, 1, 1, 0x00, 0, 0},
+	{0x00,			0,                       0, 0, 0, 0x00, 0, 0},
 };
 
 /*
@@ -553,13 +553,13 @@ static int stfsm_mx25_en_32bit_addr_seq(struct stfsm_seq *seq)
  * entering a state that is incompatible with the SPIBoot Controller.
  */
 static struct seq_rw_config stfsm_s25fl_read4_configs[] = {
-	{FLASH_FLAG_READ_1_4_4,  SPINOR_OP_READ4_1_4_4,  0, 4, 4, 0x00, 2, 4},
-	{FLASH_FLAG_READ_1_1_4,  SPINOR_OP_READ4_1_1_4,  0, 1, 4, 0x00, 0, 8},
-	{FLASH_FLAG_READ_1_2_2,  SPINOR_OP_READ4_1_2_2,  0, 2, 2, 0x00, 4, 0},
-	{FLASH_FLAG_READ_1_1_2,  SPINOR_OP_READ4_1_1_2,  0, 1, 2, 0x00, 0, 8},
-	{FLASH_FLAG_READ_FAST,   SPINOR_OP_READ4_FAST,   0, 1, 1, 0x00, 0, 8},
-	{FLASH_FLAG_READ_WRITE,  SPINOR_OP_READ4,        0, 1, 1, 0x00, 0, 0},
-	{0x00,                   0,                      0, 0, 0, 0x00, 0, 0},
+	{FLASH_FLAG_READ_1_4_4,  SPINOR_OP_READ_1_4_4_4B,  0, 4, 4, 0x00, 2, 4},
+	{FLASH_FLAG_READ_1_1_4,  SPINOR_OP_READ_1_1_4_4B,  0, 1, 4, 0x00, 0, 8},
+	{FLASH_FLAG_READ_1_2_2,  SPINOR_OP_READ_1_2_2_4B,  0, 2, 2, 0x00, 4, 0},
+	{FLASH_FLAG_READ_1_1_2,  SPINOR_OP_READ_1_1_2_4B,  0, 1, 2, 0x00, 0, 8},
+	{FLASH_FLAG_READ_FAST,   SPINOR_OP_READ_FAST_4B,   0, 1, 1, 0x00, 0, 8},
+	{FLASH_FLAG_READ_WRITE,  SPINOR_OP_READ_4B,        0, 1, 1, 0x00, 0, 0},
+	{0x00,                   0,                        0, 0, 0, 0x00, 0, 0},
 };
 
 static struct seq_rw_config stfsm_s25fl_write4_configs[] = {

drivers/mtd/spi-nor/Kconfig

@@ -29,6 +29,16 @@ config MTD_SPI_NOR_USE_4K_SECTORS
 	  Please note that some tools/drivers/filesystems may not work with
 	  4096 B erase size (e.g. UBIFS requires 15 KiB as a minimum).
 
+config SPI_ASPEED_SMC
+	tristate "Aspeed flash controllers in SPI mode"
+	depends on ARCH_ASPEED || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	help
+	  This enables support for the Firmware Memory controller (FMC)
+	  in the Aspeed AST2500/AST2400 SoCs when attached to SPI NOR chips,
+	  and support for the SPI flash memory controller (SPI) for
+	  the host firmware. The implementation only supports SPI NOR.
+
 config SPI_ATMEL_QUADSPI
 	tristate "Atmel Quad SPI Controller"
 	depends on ARCH_AT91 || (ARM && COMPILE_TEST)
@@ -40,7 +50,7 @@ config SPI_ATMEL_QUADSPI
 
 config SPI_CADENCE_QUADSPI
 	tristate "Cadence Quad SPI controller"
-	depends on OF && ARM
+	depends on OF && (ARM || COMPILE_TEST)
 	help
 	  Enable support for the Cadence Quad SPI Flash controller.
 
@@ -76,4 +86,24 @@ config SPI_NXP_SPIFI
 	  Flash. Enable this option if you have a device with a SPIFI
 	  controller and want to access the Flash as a mtd device.
 
+config SPI_INTEL_SPI
+	tristate
+
+config SPI_INTEL_SPI_PLATFORM
+	tristate "Intel PCH/PCU SPI flash platform driver" if EXPERT
+	depends on X86
+	select SPI_INTEL_SPI
+	help
+	  This enables platform support for the Intel PCH/PCU SPI
+	  controller in master mode. This controller is present in modern
+	  Intel hardware and is used to hold BIOS and other persistent
+	  settings. Using this driver it is possible to upgrade BIOS
+	  directly from Linux.
+
+	  Say N here unless you know what you are doing. Overwriting the
+	  SPI flash may render the system unbootable.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called intel-spi-platform.
+
 endif # MTD_SPI_NOR

drivers/mtd/spi-nor/Makefile

 obj-$(CONFIG_MTD_SPI_NOR)	+= spi-nor.o
+obj-$(CONFIG_SPI_ASPEED_SMC)	+= aspeed-smc.o
 obj-$(CONFIG_SPI_ATMEL_QUADSPI)	+= atmel-quadspi.o
 obj-$(CONFIG_SPI_CADENCE_QUADSPI)	+= cadence-quadspi.o
 obj-$(CONFIG_SPI_FSL_QUADSPI)	+= fsl-quadspi.o
 obj-$(CONFIG_SPI_HISI_SFC)	+= hisi-sfc.o
 obj-$(CONFIG_MTD_MT81xx_NOR)    += mtk-quadspi.o
 obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
+obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
+obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o

drivers/mtd/spi-nor/cadence-quadspi.c

@@ -526,7 +526,8 @@ static int cqspi_indirect_read_execute(struct spi_nor *nor,
 			bytes_to_read *= cqspi->fifo_width;
 			bytes_to_read = bytes_to_read > remaining ?
 					remaining : bytes_to_read;
-			readsl(ahb_base, rxbuf, DIV_ROUND_UP(bytes_to_read, 4));
+			ioread32_rep(ahb_base, rxbuf,
+				     DIV_ROUND_UP(bytes_to_read, 4));
 			rxbuf += bytes_to_read;
 			remaining -= bytes_to_read;
 			bytes_to_read = cqspi_get_rd_sram_level(cqspi);
@@ -610,7 +611,8 @@ static int cqspi_indirect_write_execute(struct spi_nor *nor,
 
 	while (remaining > 0) {
 		write_bytes = remaining > page_size ? page_size : remaining;
-		writesl(cqspi->ahb_base, txbuf, DIV_ROUND_UP(write_bytes, 4));
+		iowrite32_rep(cqspi->ahb_base, txbuf,
+			      DIV_ROUND_UP(write_bytes, 4));
 
 		ret = wait_for_completion_timeout(&cqspi->transfer_complete,
 						  msecs_to_jiffies
@@ -891,7 +893,7 @@ static ssize_t cqspi_write(struct spi_nor *nor, loff_t to,
 	if (ret)
 		return ret;
 
-	return (ret < 0) ? ret : len;
+	return len;
 }
 
 static ssize_t cqspi_read(struct spi_nor *nor, loff_t from,
@@ -911,7 +913,7 @@ static ssize_t cqspi_read(struct spi_nor *nor, loff_t from,
 	if (ret)
 		return ret;
 
-	return (ret < 0) ? ret : len;
+	return len;
 }
 
 static int cqspi_erase(struct spi_nor *nor, loff_t offs)

drivers/mtd/spi-nor/fsl-quadspi.c

@@ -193,7 +193,7 @@
 #define QUADSPI_LUT_NUM		64
 
 /* SEQID -- we can have 16 seqids at most. */
-#define SEQID_QUAD_READ		0
+#define SEQID_READ		0
 #define SEQID_WREN		1
 #define SEQID_WRDI		2
 #define SEQID_RDSR		3
@@ -373,32 +373,26 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	void __iomem *base = q->iobase;
 	int rxfifo = q->devtype_data->rxfifo;
 	u32 lut_base;
-	u8 cmd, addrlen, dummy;
 	int i;
 
+	struct spi_nor *nor = &q->nor[0];
+	u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
+	u8 read_op = nor->read_opcode;
+	u8 read_dm = nor->read_dummy;
+
 	fsl_qspi_unlock_lut(q);
 
 	/* Clear all the LUT table */
 	for (i = 0; i < QUADSPI_LUT_NUM; i++)
 		qspi_writel(q, 0, base + QUADSPI_LUT_BASE + i * 4);
 
-	/* Quad Read */
-	lut_base = SEQID_QUAD_READ * 4;
-
-	if (q->nor_size <= SZ_16M) {
-		cmd = SPINOR_OP_READ_1_1_4;
-		addrlen = ADDR24BIT;
-		dummy = 8;
-	} else {
-		/* use the 4-byte address */
-		cmd = SPINOR_OP_READ_1_1_4;
-		addrlen = ADDR32BIT;
-		dummy = 8;
-	}
+	/* Read */
+	lut_base = SEQID_READ * 4;
 
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
-	qspi_writel(q, LUT0(DUMMY, PAD1, dummy) | LUT1(FSL_READ, PAD4, rxfifo),
+	qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
+		    LUT1(FSL_READ, PAD4, rxfifo),
 			base + QUADSPI_LUT(lut_base + 1));
 
 	/* Write enable */
@@ -409,16 +403,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Page Program */
 	lut_base = SEQID_PP * 4;
 
-	if (q->nor_size <= SZ_16M) {
-		cmd = SPINOR_OP_PP;
-		addrlen = ADDR24BIT;
-	} else {
-		/* use the 4-byte address */
-		cmd = SPINOR_OP_PP;
-		addrlen = ADDR32BIT;
-	}
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
+		    LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
 	qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
 			base + QUADSPI_LUT(lut_base + 1));
@@ -432,10 +418,8 @@ static void fsl_qspi_init_lut(struct fsl_qspi *q)
 	/* Erase a sector */
 	lut_base = SEQID_SE * 4;
 
-	cmd = q->nor[0].erase_opcode;
-	addrlen = q->nor_size <= SZ_16M ? ADDR24BIT : ADDR32BIT;
-
-	qspi_writel(q, LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen),
+	qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
+		    LUT1(ADDR, PAD1, addrlen),
 			base + QUADSPI_LUT(lut_base));
 
 	/* Erase the whole chip */
@@ -484,7 +468,7 @@ static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
 {
 	switch (cmd) {
 	case SPINOR_OP_READ_1_1_4:
-		return SEQID_QUAD_READ;
+		return SEQID_READ;
 	case SPINOR_OP_WREN:
 		return SEQID_WREN;
 	case SPINOR_OP_WRDI:

drivers/mtd/spi-nor/intel-spi-platform.c

+/*
+ * Intel PCH/PCU SPI flash platform driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "intel-spi.h"
+
+static int intel_spi_platform_probe(struct platform_device *pdev)
+{
+	struct intel_spi_boardinfo *info;
+	struct intel_spi *ispi;
+	struct resource *mem;
+
+	info = dev_get_platdata(&pdev->dev);
+	if (!info)
+		return -EINVAL;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ispi = intel_spi_probe(&pdev->dev, mem, info);
+	if (IS_ERR(ispi))
+		return PTR_ERR(ispi);
+
+	platform_set_drvdata(pdev, ispi);
+	return 0;
+}
+
+static int intel_spi_platform_remove(struct platform_device *pdev)
+{
+	struct intel_spi *ispi = platform_get_drvdata(pdev);
+
+	return intel_spi_remove(ispi);
+}
+
+static struct platform_driver intel_spi_platform_driver = {
+	.probe = intel_spi_platform_probe,
+	.remove = intel_spi_platform_remove,
+	.driver = {
+		.name = "intel-spi",
+	},
+};
+
+module_platform_driver(intel_spi_platform_driver);
+
+MODULE_DESCRIPTION("Intel PCH/PCU SPI flash platform driver");
+MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:intel-spi");

drivers/mtd/spi-nor/intel-spi.c

+/*
+ * Intel PCH/PCU SPI flash driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/sizes.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/spi-nor.h>
+#include <linux/platform_data/intel-spi.h>
+
+#include "intel-spi.h"
+
+/* Offsets are from @ispi->base */
+#define BFPREG				0x00
+
+#define HSFSTS_CTL			0x04
+#define HSFSTS_CTL_FSMIE		BIT(31)
+#define HSFSTS_CTL_FDBC_SHIFT		24
+#define HSFSTS_CTL_FDBC_MASK		(0x3f << HSFSTS_CTL_FDBC_SHIFT)
+
+#define HSFSTS_CTL_FCYCLE_SHIFT		17
+#define HSFSTS_CTL_FCYCLE_MASK		(0x0f << HSFSTS_CTL_FCYCLE_SHIFT)
+/* HW sequencer opcodes */
+#define HSFSTS_CTL_FCYCLE_READ		(0x00 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_WRITE		(0x02 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_ERASE		(0x03 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_ERASE_64K	(0x04 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_RDID		(0x06 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_WRSR		(0x07 << HSFSTS_CTL_FCYCLE_SHIFT)
+#define HSFSTS_CTL_FCYCLE_RDSR		(0x08 << HSFSTS_CTL_FCYCLE_SHIFT)
+
+#define HSFSTS_CTL_FGO			BIT(16)
+#define HSFSTS_CTL_FLOCKDN		BIT(15)
+#define HSFSTS_CTL_FDV			BIT(14)
+#define HSFSTS_CTL_SCIP			BIT(5)
+#define HSFSTS_CTL_AEL			BIT(2)
+#define HSFSTS_CTL_FCERR		BIT(1)
+#define HSFSTS_CTL_FDONE		BIT(0)
+
+#define FADDR				0x08
+#define DLOCK				0x0c
+#define FDATA(n)			(0x10 + ((n) * 4))
+
+#define FRACC				0x50
+
+#define FREG(n)				(0x54 + ((n) * 4))
+#define FREG_BASE_MASK			0x3fff
+#define FREG_LIMIT_SHIFT		16
+#define FREG_LIMIT_MASK			(0x03fff << FREG_LIMIT_SHIFT)
+
+/* Offset is from @ispi->pregs */
+#define PR(n)				((n) * 4)
+#define PR_WPE				BIT(31)
+#define PR_LIMIT_SHIFT			16
+#define PR_LIMIT_MASK			(0x3fff << PR_LIMIT_SHIFT)
+#define PR_RPE				BIT(15)
+#define PR_BASE_MASK			0x3fff
+/* Last PR is GPR0 */
+#define PR_NUM				(5 + 1)
+
+/* Offsets are from @ispi->sregs */
+#define SSFSTS_CTL			0x00
+#define SSFSTS_CTL_FSMIE		BIT(23)
+#define SSFSTS_CTL_DS			BIT(22)
+#define SSFSTS_CTL_DBC_SHIFT		16
+#define SSFSTS_CTL_SPOP			BIT(11)
+#define SSFSTS_CTL_ACS			BIT(10)
+#define SSFSTS_CTL_SCGO			BIT(9)
+#define SSFSTS_CTL_COP_SHIFT		12
+#define SSFSTS_CTL_FRS			BIT(7)
+#define SSFSTS_CTL_DOFRS		BIT(6)
+#define SSFSTS_CTL_AEL			BIT(4)
+#define SSFSTS_CTL_FCERR		BIT(3)
+#define SSFSTS_CTL_FDONE		BIT(2)
+#define SSFSTS_CTL_SCIP			BIT(0)
+
+#define PREOP_OPTYPE			0x04
+#define OPMENU0				0x08
+#define OPMENU1				0x0c
+
+/* CPU specifics */
+#define BYT_PR				0x74
+#define BYT_SSFSTS_CTL			0x90
+#define BYT_BCR				0xfc
+#define BYT_BCR_WPD			BIT(0)
+#define BYT_FREG_NUM			5
+
+#define LPT_PR				0x74
+#define LPT_SSFSTS_CTL			0x90
+#define LPT_FREG_NUM			5
+
+#define BXT_PR				0x84
+#define BXT_SSFSTS_CTL			0xa0
+#define BXT_FREG_NUM			12
+
+#define INTEL_SPI_TIMEOUT		5000 /* ms */
+#define INTEL_SPI_FIFO_SZ		64
+
+/**
+ * struct intel_spi - Driver private data
+ * @dev: Device pointer
+ * @info: Pointer to board specific info
+ * @nor: SPI NOR layer structure
+ * @base: Beginning of MMIO space
+ * @pregs: Start of protection registers
+ * @sregs: Start of software sequencer registers
+ * @nregions: Maximum number of regions
+ * @writeable: Is the chip writeable
+ * @swseq: Use SW sequencer in register reads/writes
+ * @erase_64k: 64k erase supported
+ * @opcodes: Opcodes which are supported. This are programmed by BIOS
+ *           before it locks down the controller.
+ * @preopcodes: Preopcodes which are supported.
+ */
+struct intel_spi {
+	struct device *dev;
+	const struct intel_spi_boardinfo *info;
+	struct spi_nor nor;
+	void __iomem *base;
+	void __iomem *pregs;
+	void __iomem *sregs;
+	size_t nregions;
+	bool writeable;
+	bool swseq;
+	bool erase_64k;
+	u8 opcodes[8];
+	u8 preopcodes[2];
+};
+
+static bool writeable;
+module_param(writeable, bool, 0);
+MODULE_PARM_DESC(writeable, "Enable write access to SPI flash chip (default=0)");
+
+static void intel_spi_dump_regs(struct intel_spi *ispi)
+{
+	u32 value;
+	int i;
+
+	dev_dbg(ispi->dev, "BFPREG=0x%08x\n", readl(ispi->base + BFPREG));
+
+	value = readl(ispi->base + HSFSTS_CTL);
+	dev_dbg(ispi->dev, "HSFSTS_CTL=0x%08x\n", value);
+	if (value & HSFSTS_CTL_FLOCKDN)
+		dev_dbg(ispi->dev, "-> Locked\n");
+
+	dev_dbg(ispi->dev, "FADDR=0x%08x\n", readl(ispi->base + FADDR));
+	dev_dbg(ispi->dev, "DLOCK=0x%08x\n", readl(ispi->base + DLOCK));
+
+	for (i = 0; i < 16; i++)
+		dev_dbg(ispi->dev, "FDATA(%d)=0x%08x\n",
+			i, readl(ispi->base + FDATA(i)));
+
+	dev_dbg(ispi->dev, "FRACC=0x%08x\n", readl(ispi->base + FRACC));
+
+	for (i = 0; i < ispi->nregions; i++)
+		dev_dbg(ispi->dev, "FREG(%d)=0x%08x\n", i,
+			readl(ispi->base + FREG(i)));
+	for (i = 0; i < PR_NUM; i++)
+		dev_dbg(ispi->dev, "PR(%d)=0x%08x\n", i,
+			readl(ispi->pregs + PR(i)));
+
+	value = readl(ispi->sregs + SSFSTS_CTL);
+	dev_dbg(ispi->dev, "SSFSTS_CTL=0x%08x\n", value);
+	dev_dbg(ispi->dev, "PREOP_OPTYPE=0x%08x\n",
+		readl(ispi->sregs + PREOP_OPTYPE));
+	dev_dbg(ispi->dev, "OPMENU0=0x%08x\n", readl(ispi->sregs + OPMENU0));
+	dev_dbg(ispi->dev, "OPMENU1=0x%08x\n", readl(ispi->sregs + OPMENU1));
+
+	if (ispi->info->type == INTEL_SPI_BYT)
+		dev_dbg(ispi->dev, "BCR=0x%08x\n", readl(ispi->base + BYT_BCR));
+
+	dev_dbg(ispi->dev, "Protected regions:\n");
+	for (i = 0; i < PR_NUM; i++) {
+		u32 base, limit;
+
+		value = readl(ispi->pregs + PR(i));
+		if (!(value & (PR_WPE | PR_RPE)))
+			continue;
+
+		limit = (value & PR_LIMIT_MASK) >> PR_LIMIT_SHIFT;
+		base = value & PR_BASE_MASK;
+
+		dev_dbg(ispi->dev, " %02d base: 0x%08x limit: 0x%08x [%c%c]\n",
+			 i, base << 12, (limit << 12) | 0xfff,
+			 value & PR_WPE ? 'W' : '.',
+			 value & PR_RPE ? 'R' : '.');
+	}
+
+	dev_dbg(ispi->dev, "Flash regions:\n");
+	for (i = 0; i < ispi->nregions; i++) {
+		u32 region, base, limit;
+
+		region = readl(ispi->base + FREG(i));
+		base = region & FREG_BASE_MASK;
+		limit = (region & FREG_LIMIT_MASK) >> FREG_LIMIT_SHIFT;
+
+		if (base >= limit || (i > 0 && limit == 0))
+			dev_dbg(ispi->dev, " %02d disabled\n", i);
+		else
+			dev_dbg(ispi->dev, " %02d base: 0x%08x limit: 0x%08x\n",
+				 i, base << 12, (limit << 12) | 0xfff);
+	}
+
+	dev_dbg(ispi->dev, "Using %cW sequencer for register access\n",
+		ispi->swseq ? 'S' : 'H');
+}
+
+/* Reads max INTEL_SPI_FIFO_SZ bytes from the device fifo */
+static int intel_spi_read_block(struct intel_spi *ispi, void *buf, size_t size)
+{
+	size_t bytes;
+	int i = 0;
+
+	if (size > INTEL_SPI_FIFO_SZ)
+		return -EINVAL;
+
+	while (size > 0) {
+		bytes = min_t(size_t, size, 4);
+		memcpy_fromio(buf, ispi->base + FDATA(i), bytes);
+		size -= bytes;
+		buf += bytes;
+		i++;
+	}
+
+	return 0;
+}
+
+/* Writes max INTEL_SPI_FIFO_SZ bytes to the device fifo */
+static int intel_spi_write_block(struct intel_spi *ispi, const void *buf,
+				 size_t size)
+{
+	size_t bytes;
+	int i = 0;
+
+	if (size > INTEL_SPI_FIFO_SZ)
+		return -EINVAL;
+
+	while (size > 0) {
+		bytes = min_t(size_t, size, 4);
+		memcpy_toio(ispi->base + FDATA(i), buf, bytes);
+		size -= bytes;
+		buf += bytes;
+		i++;
+	}
+
+	return 0;
+}
+
+static int intel_spi_wait_hw_busy(struct intel_spi *ispi)
+{
+	u32 val;
+
+	return readl_poll_timeout(ispi->base + HSFSTS_CTL, val,
+				  !(val & HSFSTS_CTL_SCIP), 0,
+				  INTEL_SPI_TIMEOUT * 1000);
+}
+
+static int intel_spi_wait_sw_busy(struct intel_spi *ispi)
+{
+	u32 val;
+
+	return readl_poll_timeout(ispi->sregs + SSFSTS_CTL, val,
+				  !(val & SSFSTS_CTL_SCIP), 0,
+				  INTEL_SPI_TIMEOUT * 1000);
+}
+
+static int intel_spi_init(struct intel_spi *ispi)
+{
+	u32 opmenu0, opmenu1, val;
+	int i;
+
+	switch (ispi->info->type) {
+	case INTEL_SPI_BYT:
+		ispi->sregs = ispi->base + BYT_SSFSTS_CTL;
+		ispi->pregs = ispi->base + BYT_PR;
+		ispi->nregions = BYT_FREG_NUM;
+
+		if (writeable) {
+			/* Disable write protection */
+			val = readl(ispi->base + BYT_BCR);
+			if (!(val & BYT_BCR_WPD)) {
+				val |= BYT_BCR_WPD;
+				writel(val, ispi->base + BYT_BCR);
+				val = readl(ispi->base + BYT_BCR);
+			}
+
+			ispi->writeable = !!(val & BYT_BCR_WPD);
+		}
+
+		break;
+
+	case INTEL_SPI_LPT:
+		ispi->sregs = ispi->base + LPT_SSFSTS_CTL;
+		ispi->pregs = ispi->base + LPT_PR;
+		ispi->nregions = LPT_FREG_NUM;
+		break;
+
+	case INTEL_SPI_BXT:
+		ispi->sregs = ispi->base + BXT_SSFSTS_CTL;
+		ispi->pregs = ispi->base + BXT_PR;
+		ispi->nregions = BXT_FREG_NUM;
+		ispi->erase_64k = true;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	/* Disable #SMI generation */
+	val = readl(ispi->base + HSFSTS_CTL);
+	val &= ~HSFSTS_CTL_FSMIE;
+	writel(val, ispi->base + HSFSTS_CTL);
+
+	/*
+	 * BIOS programs allowed opcodes and then locks down the register.
+	 * So read back what opcodes it decided to support. That's the set
+	 * we are going to support as well.
+	 */
+	opmenu0 = readl(ispi->sregs + OPMENU0);
+	opmenu1 = readl(ispi->sregs + OPMENU1);
+
+	/*
+	 * Some controllers can only do basic operations using hardware
+	 * sequencer. All other operations are supposed to be carried out
+	 * using software sequencer. If we find that BIOS has programmed
+	 * opcodes for the software sequencer we use that over the hardware
+	 * sequencer.
+	 */
+	if (opmenu0 && opmenu1) {
+		for (i = 0; i < ARRAY_SIZE(ispi->opcodes) / 2; i++) {
+			ispi->opcodes[i] = opmenu0 >> i * 8;
+			ispi->opcodes[i + 4] = opmenu1 >> i * 8;
+		}
+
+		val = readl(ispi->sregs + PREOP_OPTYPE);
+		ispi->preopcodes[0] = val;
+		ispi->preopcodes[1] = val >> 8;
+
+		/* Disable #SMI generation from SW sequencer */
+		val = readl(ispi->sregs + SSFSTS_CTL);
+		val &= ~SSFSTS_CTL_FSMIE;
+		writel(val, ispi->sregs + SSFSTS_CTL);
+
+		ispi->swseq = true;
+	}
+
+	intel_spi_dump_regs(ispi);
+
+	return 0;
+}
+
+static int intel_spi_opcode_index(struct intel_spi *ispi, u8 opcode)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(ispi->opcodes); i++)
+		if (ispi->opcodes[i] == opcode)
+			return i;
+	return -EINVAL;
+}
+
+static int intel_spi_hw_cycle(struct intel_spi *ispi, u8 opcode, u8 *buf,
+			      int len)
+{
+	u32 val, status;
+	int ret;
+
+	val = readl(ispi->base + HSFSTS_CTL);
+	val &= ~(HSFSTS_CTL_FCYCLE_MASK | HSFSTS_CTL_FDBC_MASK);
+
+	switch (opcode) {
+	case SPINOR_OP_RDID:
+		val |= HSFSTS_CTL_FCYCLE_RDID;
+		break;
+	case SPINOR_OP_WRSR:
+		val |= HSFSTS_CTL_FCYCLE_WRSR;
+		break;
+	case SPINOR_OP_RDSR:
+		val |= HSFSTS_CTL_FCYCLE_RDSR;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	val |= (len - 1) << HSFSTS_CTL_FDBC_SHIFT;
+	val |= HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+	val |= HSFSTS_CTL_FGO;
+	writel(val, ispi->base + HSFSTS_CTL);
+
+	ret = intel_spi_wait_hw_busy(ispi);
+	if (ret)
+		return ret;
+
+	status = readl(ispi->base + HSFSTS_CTL);
+	if (status & HSFSTS_CTL_FCERR)
+		return -EIO;
+	else if (status & HSFSTS_CTL_AEL)
+		return -EACCES;
+
+	return 0;
+}
+
+static int intel_spi_sw_cycle(struct intel_spi *ispi, u8 opcode, u8 *buf,
+			      int len)
+{
+	u32 val, status;
+	int ret;
+
+	ret = intel_spi_opcode_index(ispi, opcode);
+	if (ret < 0)
+		return ret;
+
+	val = (len << SSFSTS_CTL_DBC_SHIFT) | SSFSTS_CTL_DS;
+	val |= ret << SSFSTS_CTL_COP_SHIFT;
+	val |= SSFSTS_CTL_FCERR | SSFSTS_CTL_FDONE;
+	val |= SSFSTS_CTL_SCGO;
+	writel(val, ispi->sregs + SSFSTS_CTL);
+
+	ret = intel_spi_wait_sw_busy(ispi);
+	if (ret)
+		return ret;
+
+	status = readl(ispi->base + SSFSTS_CTL);
+	if (status & SSFSTS_CTL_FCERR)
+		return -EIO;
+	else if (status & SSFSTS_CTL_AEL)
+		return -EACCES;
+
+	return 0;
+}
+
+static int intel_spi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+	struct intel_spi *ispi = nor->priv;
+	int ret;
+
+	/* Address of the first chip */
+	writel(0, ispi->base + FADDR);
+
+	if (ispi->swseq)
+		ret = intel_spi_sw_cycle(ispi, opcode, buf, len);
+	else
+		ret = intel_spi_hw_cycle(ispi, opcode, buf, len);
+
+	if (ret)
+		return ret;
+
+	return intel_spi_read_block(ispi, buf, len);
+}
+
+static int intel_spi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
+{
+	struct intel_spi *ispi = nor->priv;
+	int ret;
+
+	/*
+	 * This is handled with atomic operation and preop code in Intel
+	 * controller so skip it here now.
+	 */
+	if (opcode == SPINOR_OP_WREN)
+		return 0;
+
+	writel(0, ispi->base + FADDR);
+
+	/* Write the value beforehand */
+	ret = intel_spi_write_block(ispi, buf, len);
+	if (ret)
+		return ret;
+
+	if (ispi->swseq)
+		return intel_spi_sw_cycle(ispi, opcode, buf, len);
+	return intel_spi_hw_cycle(ispi, opcode, buf, len);
+}
+
+static ssize_t intel_spi_read(struct spi_nor *nor, loff_t from, size_t len,
+			      u_char *read_buf)
+{
+	struct intel_spi *ispi = nor->priv;
+	size_t block_size, retlen = 0;
+	u32 val, status;
+	ssize_t ret;
+
+	switch (nor->read_opcode) {
+	case SPINOR_OP_READ:
+	case SPINOR_OP_READ_FAST:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	while (len > 0) {
+		block_size = min_t(size_t, len, INTEL_SPI_FIFO_SZ);
+
+		writel(from, ispi->base + FADDR);
+
+		val = readl(ispi->base + HSFSTS_CTL);
+		val &= ~(HSFSTS_CTL_FDBC_MASK | HSFSTS_CTL_FCYCLE_MASK);
+		val |= HSFSTS_CTL_AEL | HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+		val |= (block_size - 1) << HSFSTS_CTL_FDBC_SHIFT;
+		val |= HSFSTS_CTL_FCYCLE_READ;
+		val |= HSFSTS_CTL_FGO;
+		writel(val, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_wait_hw_busy(ispi);
+		if (ret)
+			return ret;
+
+		status = readl(ispi->base + HSFSTS_CTL);
+		if (status & HSFSTS_CTL_FCERR)
+			ret = -EIO;
+		else if (status & HSFSTS_CTL_AEL)
+			ret = -EACCES;
+
+		if (ret < 0) {
+			dev_err(ispi->dev, "read error: %llx: %#x\n", from,
+				status);
+			return ret;
+		}
+
+		ret = intel_spi_read_block(ispi, read_buf, block_size);
+		if (ret)
+			return ret;
+
+		len -= block_size;
+		from += block_size;
+		retlen += block_size;
+		read_buf += block_size;
+	}
+
+	return retlen;
+}
+
+static ssize_t intel_spi_write(struct spi_nor *nor, loff_t to, size_t len,
+			       const u_char *write_buf)
+{
+	struct intel_spi *ispi = nor->priv;
+	size_t block_size, retlen = 0;
+	u32 val, status;
+	ssize_t ret;
+
+	while (len > 0) {
+		block_size = min_t(size_t, len, INTEL_SPI_FIFO_SZ);
+
+		writel(to, ispi->base + FADDR);
+
+		val = readl(ispi->base + HSFSTS_CTL);
+		val &= ~(HSFSTS_CTL_FDBC_MASK | HSFSTS_CTL_FCYCLE_MASK);
+		val |= HSFSTS_CTL_AEL | HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+		val |= (block_size - 1) << HSFSTS_CTL_FDBC_SHIFT;
+		val |= HSFSTS_CTL_FCYCLE_WRITE;
+
+		/* Write enable */
+		if (ispi->preopcodes[1] == SPINOR_OP_WREN)
+			val |= SSFSTS_CTL_SPOP;
+		val |= SSFSTS_CTL_ACS;
+		writel(val, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_write_block(ispi, write_buf, block_size);
+		if (ret) {
+			dev_err(ispi->dev, "failed to write block\n");
+			return ret;
+		}
+
+		/* Start the write now */
+		val = readl(ispi->base + HSFSTS_CTL);
+		writel(val | HSFSTS_CTL_FGO, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_wait_hw_busy(ispi);
+		if (ret) {
+			dev_err(ispi->dev, "timeout\n");
+			return ret;
+		}
+
+		status = readl(ispi->base + HSFSTS_CTL);
+		if (status & HSFSTS_CTL_FCERR)
+			ret = -EIO;
+		else if (status & HSFSTS_CTL_AEL)
+			ret = -EACCES;
+
+		if (ret < 0) {
+			dev_err(ispi->dev, "write error: %llx: %#x\n", to,
+				status);
+			return ret;
+		}
+
+		len -= block_size;
+		to += block_size;
+		retlen += block_size;
+		write_buf += block_size;
+	}
+
+	return retlen;
+}
+
+static int intel_spi_erase(struct spi_nor *nor, loff_t offs)
+{
+	size_t erase_size, len = nor->mtd.erasesize;
+	struct intel_spi *ispi = nor->priv;
+	u32 val, status, cmd;
+	int ret;
+
+	/* If the hardware can do 64k erase use that when possible */
+	if (len >= SZ_64K && ispi->erase_64k) {
+		cmd = HSFSTS_CTL_FCYCLE_ERASE_64K;
+		erase_size = SZ_64K;
+	} else {
+		cmd = HSFSTS_CTL_FCYCLE_ERASE;
+		erase_size = SZ_4K;
+	}
+
+	while (len > 0) {
+		writel(offs, ispi->base + FADDR);
+
+		val = readl(ispi->base + HSFSTS_CTL);
+		val &= ~(HSFSTS_CTL_FDBC_MASK | HSFSTS_CTL_FCYCLE_MASK);
+		val |= HSFSTS_CTL_AEL | HSFSTS_CTL_FCERR | HSFSTS_CTL_FDONE;
+		val |= cmd;
+		val |= HSFSTS_CTL_FGO;
+		writel(val, ispi->base + HSFSTS_CTL);
+
+		ret = intel_spi_wait_hw_busy(ispi);
+		if (ret)
+			return ret;
+
+		status = readl(ispi->base + HSFSTS_CTL);
+		if (status & HSFSTS_CTL_FCERR)
+			return -EIO;
+		else if (status & HSFSTS_CTL_AEL)
+			return -EACCES;
+
+		offs += erase_size;
+		len -= erase_size;
+	}
+
+	return 0;
+}
+
+static bool intel_spi_is_protected(const struct intel_spi *ispi,
+				   unsigned int base, unsigned int limit)
+{
+	int i;
+
+	for (i = 0; i < PR_NUM; i++) {
+		u32 pr_base, pr_limit, pr_value;
+
+		pr_value = readl(ispi->pregs + PR(i));
+		if (!(pr_value & (PR_WPE | PR_RPE)))
+			continue;
+
+		pr_limit = (pr_value & PR_LIMIT_MASK) >> PR_LIMIT_SHIFT;
+		pr_base = pr_value & PR_BASE_MASK;
+
+		if (pr_base >= base && pr_limit <= limit)
+			return true;
+	}
+
+	return false;
+}
+
+/*
+ * There will be a single partition holding all enabled flash regions. We
+ * call this "BIOS".
+ */
+static void intel_spi_fill_partition(struct intel_spi *ispi,
+				     struct mtd_partition *part)
+{
+	u64 end;
+	int i;
+
+	memset(part, 0, sizeof(*part));
+
+	/* Start from the mandatory descriptor region */
+	part->size = 4096;
+	part->name = "BIOS";
+
+	/*
+	 * Now try to find where this partition ends based on the flash
+	 * region registers.
+	 */
+	for (i = 1; i < ispi->nregions; i++) {
+		u32 region, base, limit;
+
+		region = readl(ispi->base + FREG(i));
+		base = region & FREG_BASE_MASK;
+		limit = (region & FREG_LIMIT_MASK) >> FREG_LIMIT_SHIFT;
+
+		if (base >= limit || limit == 0)
+			continue;
+
+		/*
+		 * If any of the regions have protection bits set, make the
+		 * whole partition read-only to be on the safe side.
+		 */
+		if (intel_spi_is_protected(ispi, base, limit))
+			ispi->writeable = 0;
+
+		end = (limit << 12) + 4096;
+		if (end > part->size)
+			part->size = end;
+	}
+}
+
+struct intel_spi *intel_spi_probe(struct device *dev,
+	struct resource *mem, const struct intel_spi_boardinfo *info)
+{
+	struct mtd_partition part;
+	struct intel_spi *ispi;
+	int ret;
+
+	if (!info || !mem)
+		return ERR_PTR(-EINVAL);
+
+	ispi = devm_kzalloc(dev, sizeof(*ispi), GFP_KERNEL);
+	if (!ispi)
+		return ERR_PTR(-ENOMEM);
+
+	ispi->base = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(ispi->base))
+		return ispi->base;
+
+	ispi->dev = dev;
+	ispi->info = info;
+	ispi->writeable = info->writeable;
+
+	ret = intel_spi_init(ispi);
+	if (ret)
+		return ERR_PTR(ret);
+
+	ispi->nor.dev = ispi->dev;
+	ispi->nor.priv = ispi;
+	ispi->nor.read_reg = intel_spi_read_reg;
+	ispi->nor.write_reg = intel_spi_write_reg;
+	ispi->nor.read = intel_spi_read;
+	ispi->nor.write = intel_spi_write;
+	ispi->nor.erase = intel_spi_erase;
+
+	ret = spi_nor_scan(&ispi->nor, NULL, SPI_NOR_NORMAL);
+	if (ret) {
+		dev_info(dev, "failed to locate the chip\n");
+		return ERR_PTR(ret);
+	}
+
+	intel_spi_fill_partition(ispi, &part);
+
+	/* Prevent writes if not explicitly enabled */
+	if (!ispi->writeable || !writeable)
+		ispi->nor.mtd.flags &= ~MTD_WRITEABLE;
+
+	ret = mtd_device_parse_register(&ispi->nor.mtd, NULL, NULL, &part, 1);
+	if (ret)
+		return ERR_PTR(ret);
+
+	return ispi;
+}
+EXPORT_SYMBOL_GPL(intel_spi_probe);
+
+int intel_spi_remove(struct intel_spi *ispi)
+{
+	return mtd_device_unregister(&ispi->nor.mtd);
+}
+EXPORT_SYMBOL_GPL(intel_spi_remove);
+
+MODULE_DESCRIPTION("Intel PCH/PCU SPI flash core driver");
+MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
+MODULE_LICENSE("GPL v2");

drivers/mtd/spi-nor/intel-spi.h

+/*
+ * Intel PCH/PCU SPI flash driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef INTEL_SPI_H
+#define INTEL_SPI_H
+
+#include <linux/platform_data/intel-spi.h>
+
+struct intel_spi;
+struct resource;
+
+struct intel_spi *intel_spi_probe(struct device *dev,
+	struct resource *mem, const struct intel_spi_boardinfo *info);
+int intel_spi_remove(struct intel_spi *ispi);
+
+#endif /* INTEL_SPI_H */

drivers/mtd/spi-nor/spi-nor.c

@@ -75,6 +75,16 @@ struct flash_info {
 					 * bit. Must be used with
 					 * SPI_NOR_HAS_LOCK.
 					 */
+#define	SPI_S3AN		BIT(10)	/*
+					 * Xilinx Spartan 3AN In-System Flash
+					 * (MFR cannot be used for probing
+					 * because it has the same value as
+					 * ATMEL flashes)
+					 */
+#define SPI_NOR_4B_OPCODES	BIT(11)	/*
+					 * Use dedicated 4byte address op codes
+					 * to support memory size above 128Mib.
+					 */
 };
 
 #define JEDEC_MFR(info)	((info)->id[0])
@@ -188,6 +198,78 @@ static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
 	return mtd->priv;
 }
 
+
+static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
+{
+	size_t i;
+
+	for (i = 0; i < size; i++)
+		if (table[i][0] == opcode)
+			return table[i][1];
+
+	/* No conversion found, keep input op code. */
+	return opcode;
+}
+
+static inline u8 spi_nor_convert_3to4_read(u8 opcode)
+{
+	static const u8 spi_nor_3to4_read[][2] = {
+		{ SPINOR_OP_READ,	SPINOR_OP_READ_4B },
+		{ SPINOR_OP_READ_FAST,	SPINOR_OP_READ_FAST_4B },
+		{ SPINOR_OP_READ_1_1_2,	SPINOR_OP_READ_1_1_2_4B },
+		{ SPINOR_OP_READ_1_2_2,	SPINOR_OP_READ_1_2_2_4B },
+		{ SPINOR_OP_READ_1_1_4,	SPINOR_OP_READ_1_1_4_4B },
+		{ SPINOR_OP_READ_1_4_4,	SPINOR_OP_READ_1_4_4_4B },
+	};
+
+	return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
+				      ARRAY_SIZE(spi_nor_3to4_read));
+}
+
+static inline u8 spi_nor_convert_3to4_program(u8 opcode)
+{
+	static const u8 spi_nor_3to4_program[][2] = {
+		{ SPINOR_OP_PP,		SPINOR_OP_PP_4B },
+		{ SPINOR_OP_PP_1_1_4,	SPINOR_OP_PP_1_1_4_4B },
+		{ SPINOR_OP_PP_1_4_4,	SPINOR_OP_PP_1_4_4_4B },
+	};
+
+	return spi_nor_convert_opcode(opcode, spi_nor_3to4_program,
+				      ARRAY_SIZE(spi_nor_3to4_program));
+}
+
+static inline u8 spi_nor_convert_3to4_erase(u8 opcode)
+{
+	static const u8 spi_nor_3to4_erase[][2] = {
+		{ SPINOR_OP_BE_4K,	SPINOR_OP_BE_4K_4B },
+		{ SPINOR_OP_BE_32K,	SPINOR_OP_BE_32K_4B },
+		{ SPINOR_OP_SE,		SPINOR_OP_SE_4B },
+	};
+
+	return spi_nor_convert_opcode(opcode, spi_nor_3to4_erase,
+				      ARRAY_SIZE(spi_nor_3to4_erase));
+}
+
+static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
+				      const struct flash_info *info)
+{
+	/* Do some manufacturer fixups first */
+	switch (JEDEC_MFR(info)) {
+	case SNOR_MFR_SPANSION:
+		/* No small sector erase for 4-byte command set */
+		nor->erase_opcode = SPINOR_OP_SE;
+		nor->mtd.erasesize = info->sector_size;
+		break;
+
+	default:
+		break;
+	}
+
+	nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
+	nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
+	nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
+}
+
 /* Enable/disable 4-byte addressing mode. */
 static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
 			    int enable)
@@ -217,6 +299,21 @@ static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
 		return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
 	}
 }
+
+static int s3an_sr_ready(struct spi_nor *nor)
+{
+	int ret;
+	u8 val;
+
+	ret = nor->read_reg(nor, SPINOR_OP_XRDSR, &val, 1);
+	if (ret < 0) {
+		dev_err(nor->dev, "error %d reading XRDSR\n", (int) ret);
+		return ret;
+	}
+
+	return !!(val & XSR_RDY);
+}
+
 static inline int spi_nor_sr_ready(struct spi_nor *nor)
 {
 	int sr = read_sr(nor);
@@ -238,7 +335,11 @@ static inline int spi_nor_fsr_ready(struct spi_nor *nor)
 static int spi_nor_ready(struct spi_nor *nor)
 {
 	int sr, fsr;
-	sr = spi_nor_sr_ready(nor);
+
+	if (nor->flags & SNOR_F_READY_XSR_RDY)
+		sr = s3an_sr_ready(nor);
+	else
+		sr = spi_nor_sr_ready(nor);
 	if (sr < 0)
 		return sr;
 	fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
@@ -319,6 +420,27 @@ static void spi_nor_unlock_and_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
 	mutex_unlock(&nor->lock);
 }
 
+/*
+ * This code converts an address to the Default Address Mode, that has non
+ * power of two page sizes. We must support this mode because it is the default
+ * mode supported by Xilinx tools, it can access the whole flash area and
+ * changing over to the Power-of-two mode is irreversible and corrupts the
+ * original data.
+ * Addr can safely be unsigned int, the biggest S3AN device is smaller than
+ * 4 MiB.
+ */
+static loff_t spi_nor_s3an_addr_convert(struct spi_nor *nor, unsigned int addr)
+{
+	unsigned int offset;
+	unsigned int page;
+
+	offset = addr % nor->page_size;
+	page = addr / nor->page_size;
+	page <<= (nor->page_size > 512) ? 10 : 9;
+
+	return page | offset;
+}
+
 /*
  * Initiate the erasure of a single sector
  */
@@ -327,6 +449,9 @@ static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
 	u8 buf[SPI_NOR_MAX_ADDR_WIDTH];
 	int i;
 
+	if (nor->flags & SNOR_F_S3AN_ADDR_DEFAULT)
+		addr = spi_nor_s3an_addr_convert(nor, addr);
+
 	if (nor->erase)
 		return nor->erase(nor, addr);
 
@@ -368,7 +493,7 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 		return ret;
 
 	/* whole-chip erase? */
-	if (len == mtd->size) {
+	if (len == mtd->size && !(nor->flags & SNOR_F_NO_OP_CHIP_ERASE)) {
 		unsigned long timeout;
 
 		write_enable(nor);
@@ -782,6 +907,19 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 		.addr_width = (_addr_width),				\
 		.flags = (_flags),
 
+#define S3AN_INFO(_jedec_id, _n_sectors, _page_size)			\
+		.id = {							\
+			((_jedec_id) >> 16) & 0xff,			\
+			((_jedec_id) >> 8) & 0xff,			\
+			(_jedec_id) & 0xff				\
+			},						\
+		.id_len = 3,						\
+		.sector_size = (8*_page_size),				\
+		.n_sectors = (_n_sectors),				\
+		.page_size = _page_size,				\
+		.addr_width = 3,					\
+		.flags = SPI_NOR_NO_FR | SPI_S3AN,
+
 /* NOTE: double check command sets and memory organization when you add
  * more nor chips.  This current list focusses on newer chips, which
  * have been converging on command sets which including JEDEC ID.
@@ -821,7 +959,7 @@ static const struct flash_info spi_nor_ids[] = {
 	{ "en25s64",	INFO(0x1c3817, 0, 64 * 1024,  128, SECT_4K) },
 
 	/* ESMT */
-	{ "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64, SECT_4K) },
+	{ "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64, SECT_4K | SPI_NOR_HAS_LOCK) },
 
 	/* Everspin */
 	{ "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
@@ -832,6 +970,11 @@ static const struct flash_info spi_nor_ids[] = {
 	{ "mb85rs1mt", INFO(0x047f27, 0, 128 * 1024, 1, SPI_NOR_NO_ERASE) },
 
 	/* GigaDevice */
+	{
+		"gd25q16", INFO(0xc84015, 0, 64 * 1024,  32,
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+			SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+	},
 	{
 		"gd25q32", INFO(0xc84016, 0, 64 * 1024,  64,
 			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
@@ -1014,6 +1157,13 @@ static const struct flash_info spi_nor_ids[] = {
 	{ "cat25c09", CAT25_INFO( 128, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
 	{ "cat25c17", CAT25_INFO( 256, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
 	{ "cat25128", CAT25_INFO(2048, 8, 64, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) },
+
+	/* Xilinx S3AN Internal Flash */
+	{ "3S50AN", S3AN_INFO(0x1f2200, 64, 264) },
+	{ "3S200AN", S3AN_INFO(0x1f2400, 256, 264) },
+	{ "3S400AN", S3AN_INFO(0x1f2400, 256, 264) },
+	{ "3S700AN", S3AN_INFO(0x1f2500, 512, 264) },
+	{ "3S1400AN", S3AN_INFO(0x1f2600, 512, 528) },
 	{ },
 };
 
@@ -1054,7 +1204,12 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
 		return ret;
 
 	while (len) {
-		ret = nor->read(nor, from, len, buf);
+		loff_t addr = from;
+
+		if (nor->flags & SNOR_F_S3AN_ADDR_DEFAULT)
+			addr = spi_nor_s3an_addr_convert(nor, addr);
+
+		ret = nor->read(nor, addr, len, buf);
 		if (ret == 0) {
 			/* We shouldn't see 0-length reads */
 			ret = -EIO;
@@ -1175,17 +1330,32 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
 
 	for (i = 0; i < len; ) {
 		ssize_t written;
+		loff_t addr = to + i;
+
+		/*
+		 * If page_size is a power of two, the offset can be quickly
+		 * calculated with an AND operation. On the other cases we
+		 * need to do a modulus operation (more expensive).
+		 * Power of two numbers have only one bit set and we can use
+		 * the instruction hweight32 to detect if we need to do a
+		 * modulus (do_div()) or not.
+		 */
+		if (hweight32(nor->page_size) == 1) {
+			page_offset = addr & (nor->page_size - 1);
+		} else {
+			uint64_t aux = addr;
 
-		page_offset = (to + i) & (nor->page_size - 1);
-		WARN_ONCE(page_offset,
-			  "Writing at offset %zu into a NOR page. Writing partial pages may decrease reliability and increase wear of NOR flash.",
-			  page_offset);
+			page_offset = do_div(aux, nor->page_size);
+		}
 		/* the size of data remaining on the first page */
 		page_remain = min_t(size_t,
 				    nor->page_size - page_offset, len - i);
 
+		if (nor->flags & SNOR_F_S3AN_ADDR_DEFAULT)
+			addr = spi_nor_s3an_addr_convert(nor, addr);
+
 		write_enable(nor);
-		ret = nor->write(nor, to + i, page_remain, buf + i);
+		ret = nor->write(nor, addr, page_remain, buf + i);
 		if (ret < 0)
 			goto write_err;
 		written = ret;
@@ -1216,6 +1386,9 @@ static int macronix_quad_enable(struct spi_nor *nor)
 	val = read_sr(nor);
 	if (val < 0)
 		return val;
+	if (val & SR_QUAD_EN_MX)
+		return 0;
+
 	write_enable(nor);
 
 	write_sr(nor, val | SR_QUAD_EN_MX);
@@ -1312,6 +1485,47 @@ static int spi_nor_check(struct spi_nor *nor)
 	return 0;
 }
 
+static int s3an_nor_scan(const struct flash_info *info, struct spi_nor *nor)
+{
+	int ret;
+	u8 val;
+
+	ret = nor->read_reg(nor, SPINOR_OP_XRDSR, &val, 1);
+	if (ret < 0) {
+		dev_err(nor->dev, "error %d reading XRDSR\n", (int) ret);
+		return ret;
+	}
+
+	nor->erase_opcode = SPINOR_OP_XSE;
+	nor->program_opcode = SPINOR_OP_XPP;
+	nor->read_opcode = SPINOR_OP_READ;
+	nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
+
+	/*
+	 * This flashes have a page size of 264 or 528 bytes (known as
+	 * Default addressing mode). It can be changed to a more standard
+	 * Power of two mode where the page size is 256/512. This comes
+	 * with a price: there is 3% less of space, the data is corrupted
+	 * and the page size cannot be changed back to default addressing
+	 * mode.
+	 *
+	 * The current addressing mode can be read from the XRDSR register
+	 * and should not be changed, because is a destructive operation.
+	 */
+	if (val & XSR_PAGESIZE) {
+		/* Flash in Power of 2 mode */
+		nor->page_size = (nor->page_size == 264) ? 256 : 512;
+		nor->mtd.writebufsize = nor->page_size;
+		nor->mtd.size = 8 * nor->page_size * info->n_sectors;
+		nor->mtd.erasesize = 8 * nor->page_size;
+	} else {
+		/* Flash in Default addressing mode */
+		nor->flags |= SNOR_F_S3AN_ADDR_DEFAULT;
+	}
+
+	return 0;
+}
+
 int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 {
 	const struct flash_info *info = NULL;
@@ -1359,6 +1573,14 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 
 	mutex_init(&nor->lock);
 
+	/*
+	 * Make sure the XSR_RDY flag is set before calling
+	 * spi_nor_wait_till_ready(). Xilinx S3AN share MFR
+	 * with Atmel spi-nor
+	 */
+	if (info->flags & SPI_S3AN)
+		nor->flags |=  SNOR_F_READY_XSR_RDY;
+
 	/*
 	 * Atmel, SST, Intel/Numonyx, and others serial NOR tend to power up
 	 * with the software protection bits set
@@ -1483,27 +1705,10 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 	else if (mtd->size > 0x1000000) {
 		/* enable 4-byte addressing if the device exceeds 16MiB */
 		nor->addr_width = 4;
-		if (JEDEC_MFR(info) == SNOR_MFR_SPANSION) {
-			/* Dedicated 4-byte command set */
-			switch (nor->flash_read) {
-			case SPI_NOR_QUAD:
-				nor->read_opcode = SPINOR_OP_READ4_1_1_4;
-				break;
-			case SPI_NOR_DUAL:
-				nor->read_opcode = SPINOR_OP_READ4_1_1_2;
-				break;
-			case SPI_NOR_FAST:
-				nor->read_opcode = SPINOR_OP_READ4_FAST;
-				break;
-			case SPI_NOR_NORMAL:
-				nor->read_opcode = SPINOR_OP_READ4;
-				break;
-			}
-			nor->program_opcode = SPINOR_OP_PP_4B;
-			/* No small sector erase for 4-byte command set */
-			nor->erase_opcode = SPINOR_OP_SE_4B;
-			mtd->erasesize = info->sector_size;
-		} else
+		if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
+		    info->flags & SPI_NOR_4B_OPCODES)
+			spi_nor_set_4byte_opcodes(nor, info);
+		else
 			set_4byte(nor, info, 1);
 	} else {
 		nor->addr_width = 3;
@@ -1517,6 +1722,12 @@ int spi_nor_scan(struct spi_nor *nor, const char *name, enum read_mode mode)
 
 	nor->read_dummy = spi_nor_read_dummy_cycles(nor);
 
+	if (info->flags & SPI_S3AN) {
+		ret = s3an_nor_scan(info, nor);
+		if (ret)
+			return ret;
+	}
+
 	dev_info(dev, "%s (%lld Kbytes)\n", info->name,
 			(long long)mtd->size >> 10);
 

drivers/spi/spi-bcm-qspi.c

@@ -371,7 +371,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
 			/* default mode, does not need flex_cmd */
 			flex_mode = 0;
 		else
-			command = SPINOR_OP_READ4_FAST;
+			command = SPINOR_OP_READ_FAST_4B;
 		break;
 	case SPI_NBITS_DUAL:
 		bpc = 0x00000001;
@@ -384,7 +384,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
 		} else {
 			command = SPINOR_OP_READ_1_1_2;
 			if (spans_4byte)
-				command = SPINOR_OP_READ4_1_1_2;
+				command = SPINOR_OP_READ_1_1_2_4B;
 		}
 		break;
 	case SPI_NBITS_QUAD:
@@ -399,7 +399,7 @@ static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
 		} else {
 			command = SPINOR_OP_READ_1_1_4;
 			if (spans_4byte)
-				command = SPINOR_OP_READ4_1_1_4;
+				command = SPINOR_OP_READ_1_1_4_4B;
 		}
 		break;
 	default:

include/linux/mfd/lpc_ich.h

@@ -20,6 +20,8 @@
 #ifndef LPC_ICH_H
 #define LPC_ICH_H
 
+#include <linux/platform_data/intel-spi.h>
+
 /* GPIO resources */
 #define ICH_RES_GPIO	0
 #define ICH_RES_GPE0	1
@@ -40,6 +42,7 @@ struct lpc_ich_info {
 	char name[32];
 	unsigned int iTCO_version;
 	unsigned int gpio_version;
+	enum intel_spi_type spi_type;
 	u8 use_gpio;
 };
 

include/linux/mtd/spi-nor.h

@@ -43,9 +43,13 @@
 #define SPINOR_OP_WRSR		0x01	/* Write status register 1 byte */
 #define SPINOR_OP_READ		0x03	/* Read data bytes (low frequency) */
 #define SPINOR_OP_READ_FAST	0x0b	/* Read data bytes (high frequency) */
-#define SPINOR_OP_READ_1_1_2	0x3b	/* Read data bytes (Dual SPI) */
-#define SPINOR_OP_READ_1_1_4	0x6b	/* Read data bytes (Quad SPI) */
+#define SPINOR_OP_READ_1_1_2	0x3b	/* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2	0xbb	/* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4	0x6b	/* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4	0xeb	/* Read data bytes (Quad I/O SPI) */
 #define SPINOR_OP_PP		0x02	/* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4	0x32	/* Quad page program */
+#define SPINOR_OP_PP_1_4_4	0x38	/* Quad page program */
 #define SPINOR_OP_BE_4K		0x20	/* Erase 4KiB block */
 #define SPINOR_OP_BE_4K_PMC	0xd7	/* Erase 4KiB block on PMC chips */
 #define SPINOR_OP_BE_32K	0x52	/* Erase 32KiB block */
@@ -56,11 +60,17 @@
 #define SPINOR_OP_RDFSR		0x70	/* Read flag status register */
 
 /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
-#define SPINOR_OP_READ4		0x13	/* Read data bytes (low frequency) */
-#define SPINOR_OP_READ4_FAST	0x0c	/* Read data bytes (high frequency) */
-#define SPINOR_OP_READ4_1_1_2	0x3c	/* Read data bytes (Dual SPI) */
-#define SPINOR_OP_READ4_1_1_4	0x6c	/* Read data bytes (Quad SPI) */
+#define SPINOR_OP_READ_4B	0x13	/* Read data bytes (low frequency) */
+#define SPINOR_OP_READ_FAST_4B	0x0c	/* Read data bytes (high frequency) */
+#define SPINOR_OP_READ_1_1_2_4B	0x3c	/* Read data bytes (Dual Output SPI) */
+#define SPINOR_OP_READ_1_2_2_4B	0xbc	/* Read data bytes (Dual I/O SPI) */
+#define SPINOR_OP_READ_1_1_4_4B	0x6c	/* Read data bytes (Quad Output SPI) */
+#define SPINOR_OP_READ_1_4_4_4B	0xec	/* Read data bytes (Quad I/O SPI) */
 #define SPINOR_OP_PP_4B		0x12	/* Page program (up to 256 bytes) */
+#define SPINOR_OP_PP_1_1_4_4B	0x34	/* Quad page program */
+#define SPINOR_OP_PP_1_4_4_4B	0x3e	/* Quad page program */
+#define SPINOR_OP_BE_4K_4B	0x21	/* Erase 4KiB block */
+#define SPINOR_OP_BE_32K_4B	0x5c	/* Erase 32KiB block */
 #define SPINOR_OP_SE_4B		0xdc	/* Sector erase (usually 64KiB) */
 
 /* Used for SST flashes only. */
@@ -68,6 +78,15 @@
 #define SPINOR_OP_WRDI		0x04	/* Write disable */
 #define SPINOR_OP_AAI_WP	0xad	/* Auto address increment word program */
 
+/* Used for S3AN flashes only */
+#define SPINOR_OP_XSE		0x50	/* Sector erase */
+#define SPINOR_OP_XPP		0x82	/* Page program */
+#define SPINOR_OP_XRDSR		0xd7	/* Read status register */
+
+#define XSR_PAGESIZE		BIT(0)	/* Page size in Po2 or Linear */
+#define XSR_RDY			BIT(7)	/* Ready */
+
+
 /* Used for Macronix and Winbond flashes. */
 #define SPINOR_OP_EN4B		0xb7	/* Enter 4-byte mode */
 #define SPINOR_OP_EX4B		0xe9	/* Exit 4-byte mode */
@@ -119,6 +138,9 @@ enum spi_nor_ops {
 enum spi_nor_option_flags {
 	SNOR_F_USE_FSR		= BIT(0),
 	SNOR_F_HAS_SR_TB	= BIT(1),
+	SNOR_F_NO_OP_CHIP_ERASE	= BIT(2),
+	SNOR_F_S3AN_ADDR_DEFAULT = BIT(3),
+	SNOR_F_READY_XSR_RDY	= BIT(4),
 };
 
 /**

include/linux/platform_data/intel-spi.h

+/*
+ * Intel PCH/PCU SPI flash driver.
+ *
+ * Copyright (C) 2016, Intel Corporation
+ * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef INTEL_SPI_PDATA_H
+#define INTEL_SPI_PDATA_H
+
+enum intel_spi_type {
+	INTEL_SPI_BYT = 1,
+	INTEL_SPI_LPT,
+	INTEL_SPI_BXT,
+};
+
+/**
+ * struct intel_spi_boardinfo - Board specific data for Intel SPI driver
+ * @type: Type which this controller is compatible with
+ * @writeable: The chip is writeable
+ */
+struct intel_spi_boardinfo {
+	enum intel_spi_type type;
+	bool writeable;
+};
+
+#endif /* INTEL_SPI_PDATA_H */