media: ccs-pll: Check for derating and overrating, support non-derating sensors

Some sensors support derating (VT domain speed faster than OP) or
overrating (VT domain speed slower than OP). While this was supported for
the driver, the hardware support for the feature was never verified. Do
that now, and for those devices without that support, VT and OP speeds
have to match.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>

drivers/media/i2c/ccs-pll.c

@@ -142,6 +142,18 @@ static int check_all_bounds(struct device *dev,
 			lim->vt_bk.max_pix_clk_freq_hz,
 			"vt_pix_clk_freq_hz");
 
+	if (!(pll->flags & CCS_PLL_FLAG_FIFO_DERATING) &&
+	    pll->pixel_rate_pixel_array > pll->pixel_rate_csi) {
+		dev_dbg(dev, "device does not support derating\n");
+		return -EINVAL;
+	}
+
+	if (!(pll->flags & CCS_PLL_FLAG_FIFO_OVERRATING) &&
+	    pll->pixel_rate_pixel_array < pll->pixel_rate_csi) {
+		dev_dbg(dev, "device does not support overrating\n");
+		return -EINVAL;
+	}
+
 	return rval;
 }
 
@@ -163,37 +175,51 @@ __ccs_pll_calculate_vt(struct device *dev, const struct ccs_pll_limits *lim,
 	uint32_t min_sys_div, max_sys_div;
 
 	/*
-	 * Some sensors perform analogue binning and some do this
-	 * digitally. The ones doing this digitally can be roughly be
-	 * found out using this formula. The ones doing this digitally
-	 * should run at higher clock rate, so smaller divisor is used
-	 * on video timing side.
+	 * Find out whether a sensor supports derating. If it does not, VT and
+	 * OP domains are required to run at the same pixel rate.
 	 */
-	if (lim->min_line_length_pck_bin > lim->min_line_length_pck
-	    / pll->binning_horizontal)
-		vt_op_binning_div = pll->binning_horizontal;
-	else
-		vt_op_binning_div = 1;
-	dev_dbg(dev, "vt_op_binning_div: %u\n", vt_op_binning_div);
+	if (!(pll->flags & CCS_PLL_FLAG_FIFO_DERATING)) {
+		min_vt_div =
+			op_pll_bk->sys_clk_div * op_pll_bk->pix_clk_div
+			* pll->vt_lanes * phy_const
+			/ pll->op_lanes / PHY_CONST_DIV;
+	} else {
+		/*
+		 * Some sensors perform analogue binning and some do this
+		 * digitally. The ones doing this digitally can be roughly be
+		 * found out using this formula. The ones doing this digitally
+		 * should run at higher clock rate, so smaller divisor is used
+		 * on video timing side.
+		 */
+		if (lim->min_line_length_pck_bin > lim->min_line_length_pck
+		    / pll->binning_horizontal)
+			vt_op_binning_div = pll->binning_horizontal;
+		else
+			vt_op_binning_div = 1;
+		dev_dbg(dev, "vt_op_binning_div: %u\n", vt_op_binning_div);
 
-	/*
-	 * Profile 2 supports vt_pix_clk_div E [4, 10]
-	 *
-	 * Horizontal binning can be used as a base for difference in
-	 * divisors. One must make sure that horizontal blanking is
-	 * enough to accommodate the CSI-2 sync codes.
-	 *
-	 * Take scaling factor and number of VT lanes into account as well.
-	 *
-	 * Find absolute limits for the factor of vt divider.
-	 */
-	dev_dbg(dev, "scale_m: %u\n", pll->scale_m);
-	min_vt_div = DIV_ROUND_UP(pll->bits_per_pixel * op_pll_bk->sys_clk_div
-				  * pll->scale_n * pll->vt_lanes * phy_const,
-				  (pll->flags & CCS_PLL_FLAG_LANE_SPEED_MODEL ?
-				   pll->csi2.lanes : 1)
-				  * vt_op_binning_div * pll->scale_m
-				  * PHY_CONST_DIV);
+		/*
+		 * Profile 2 supports vt_pix_clk_div E [4, 10]
+		 *
+		 * Horizontal binning can be used as a base for difference in
+		 * divisors. One must make sure that horizontal blanking is
+		 * enough to accommodate the CSI-2 sync codes.
+		 *
+		 * Take scaling factor and number of VT lanes into account as well.
+		 *
+		 * Find absolute limits for the factor of vt divider.
+		 */
+		dev_dbg(dev, "scale_m: %u\n", pll->scale_m);
+		min_vt_div =
+			DIV_ROUND_UP(pll->bits_per_pixel
+				     * op_pll_bk->sys_clk_div * pll->scale_n
+				     * pll->vt_lanes * phy_const,
+				     (pll->flags &
+				      CCS_PLL_FLAG_LANE_SPEED_MODEL ?
+				      pll->csi2.lanes : 1)
+				     * vt_op_binning_div * pll->scale_m
+				     * PHY_CONST_DIV);
+	}
 
 	/* Find smallest and biggest allowed vt divisor. */
 	dev_dbg(dev, "min_vt_div: %u\n", min_vt_div);

drivers/media/i2c/ccs-pll.h

@@ -27,6 +27,8 @@
 #define CCS_PLL_FLAG_LINK_DECOUPLED				BIT(3)
 #define CCS_PLL_FLAG_EXT_IP_PLL_DIVIDER				BIT(4)
 #define CCS_PLL_FLAG_FLEXIBLE_OP_PIX_CLK_DIV			BIT(5)
+#define CCS_PLL_FLAG_FIFO_DERATING				BIT(6)
+#define CCS_PLL_FLAG_FIFO_OVERRATING				BIT(7)
 
 /**
  * struct ccs_pll_branch_fr - CCS PLL configuration (front)

drivers/media/i2c/ccs/ccs-core.c

@@ -3224,6 +3224,13 @@ static int ccs_probe(struct i2c_client *client)
 	if (CCS_LIM(sensor, CLOCK_TREE_PLL_CAPABILITY) &
 	    CCS_CLOCK_TREE_PLL_CAPABILITY_FLEXIBLE_OP_PIX_CLK_DIV)
 		sensor->pll.flags |= CCS_PLL_FLAG_FLEXIBLE_OP_PIX_CLK_DIV;
+	if (CCS_LIM(sensor, FIFO_SUPPORT_CAPABILITY) &
+	    CCS_FIFO_SUPPORT_CAPABILITY_DERATING)
+		sensor->pll.flags |= CCS_PLL_FLAG_FIFO_DERATING;
+	if (CCS_LIM(sensor, FIFO_SUPPORT_CAPABILITY) &
+	    CCS_FIFO_SUPPORT_CAPABILITY_DERATING_OVERRATING)
+		sensor->pll.flags |= CCS_PLL_FLAG_FIFO_DERATING |
+				     CCS_PLL_FLAG_FIFO_OVERRATING;
 	sensor->pll.op_bits_per_lane = CCS_LIM(sensor, OP_BITS_PER_LANE);
 	sensor->pll.ext_clk_freq_hz = sensor->hwcfg.ext_clk;
 	sensor->pll.scale_n = CCS_LIM(sensor, SCALER_N_MIN);