ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx

pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.

Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x

SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.

This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:

https://bugzilla.kernel.org/show_bug.cgi?id=63821

Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: NBalaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -246,15 +246,6 @@
 			0xf0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
-};
-
-&omap4_pmx_wkup {
-	led_wkgpio_pins: pinmux_leds_wkpins {
-		pinctrl-single,pins = <
-			0x1a (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk7 */
-			0x1c (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk8 */
-		>;
-	};
 
 	/*
 	 * wl12xx GPIO outputs for WLAN_EN, BT_EN, FM_EN, BT_WAKEUP
@@ -274,7 +265,7 @@
 		pinctrl-single,pins = <
 			0x38 (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs2.gpio_52 */
 			0x3a (PIN_INPUT | MUX_MODE3)		/* gpmc_ncs3.gpio_53 */
-			0x108 (PIN_OUTPUT | MUX_MODE0)		/* sdmmc5_clk.sdmmc5_clk */
+			0x108 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_clk.sdmmc5_clk */
 			0x10a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_cmd.sdmmc5_cmd */
 			0x10c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat0.sdmmc5_dat0 */
 			0x10e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc5_dat1.sdmmc5_dat1 */
@@ -284,6 +275,15 @@
 	};
 };
 
+&omap4_pmx_wkup {
+	led_wkgpio_pins: pinmux_leds_wkpins {
+		pinctrl-single,pins = <
+			0x1a (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk7 */
+			0x1c (PIN_OUTPUT | MUX_MODE3)	/* gpio_wk8 */
+		>;
+	};
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_pins>;