ARM: dts: sunxi: Switch to the generic PHY properties

The DWMAC specific properties to manage the PHY have been superseeded by
the generic PHY properties. Let's move to it.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

arch/arm/boot/dts/sun6i-a31-hummingbird.dts

@@ -155,13 +155,13 @@
 	pinctrl-0 = <&gmac_rgmii_pins>;
 	phy = <&phy1>;
 	phy-mode = "rgmii";
-	snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>;
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
 		reg = <1>;
+		reset-gpios = <&pio 0 21 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <30000>;
 	};
 };
 

arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts

@@ -95,13 +95,13 @@
 	phy = <&phy1>;
 	phy-mode = "rgmii";
 	phy-supply = <&reg_dldo1>;
-	snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 30000>;
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
 		reg = <1>;
+		reset-gpios = <&pio 0 21 GPIO_ACTIVE_LOW>; /* PA21 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <30000>;
 	};
 };
 

arch/arm/boot/dts/sun7i-a20-hummingbird.dts

@@ -103,15 +103,14 @@
 	phy = <&phy1>;
 	phy-mode = "rgmii";
 	phy-supply = <&reg_gmac_vdd>;
-	/* phy reset config */
-	snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */
-	snps,reset-active-low;
-	/* wait 1s after reset, otherwise fail to read phy id */
-	snps,reset-delays-us = <0 10000 1000000>;
 	status = "okay";
 
 	phy1: ethernet-phy@1 {
 		reg = <1>;
+		reset-gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+		reset-assert-us = <10000>;
+		/* wait 1s after reset, otherwise fail to read phy id */
+		reset-deassert-us = <1000000>;
 	};
 };
 

arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts

@@ -108,14 +108,14 @@
 	phy = <&phy3>;
 	phy-mode = "rgmii";
 	phy-supply = <&reg_vcc3v3>;
-
-	snps,reset-gpio = <&pio 0 17 GPIO_ACTIVE_HIGH>;
-	snps,reset-active-low;
-	snps,reset-delays-us = <0 10000 1000000>;
 	status = "okay";
 
 	phy3: ethernet-phy@3 {
 		reg = <3>;
+		reset-gpios = <&pio 0 17 GPIO_ACTIVE_LOW>; /* PA17 */
+		reset-assert-us = <10000>;
+		/* wait 1s after reset, otherwise fail to read phy id */
+		reset-deassert-us = <1000000>;
 	};
 };