net: phy: dp83867: IO impedance is not dependent on RGMII delay

The driver would only set the IO impedance value when RGMII internal
delays were enabled.  There is no reason for this.  Move the IO
impedance block out of the RGMII delay block.

Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NTrent Piepho <tpiepho@impinj.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/phy/dp83867.c

@@ -75,8 +75,7 @@
 #define DP83867_RGMII_RX_CLK_DELAY_SHIFT	0
 
 /* IO_MUX_CFG bits */
-#define DP83867_IO_MUX_CFG_IO_IMPEDANCE_CTRL	0x1f
-
+#define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MASK	0x1f
 #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX	0x0
 #define DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN	0x1f
 #define DP83867_IO_MUX_CFG_CLK_O_DISABLE	BIT(6)
@@ -162,8 +161,6 @@ static int dp83867_of_init(struct phy_device *phydev)
 	if (!of_node)
 		return -ENODEV;
 
-	dp83867->io_impedance = -EINVAL;
-
 	/* Optional configuration */
 	ret = of_property_read_u32(of_node, "ti,clk-output-sel",
 				   &dp83867->clk_output_sel);
@@ -185,6 +182,8 @@ static int dp83867_of_init(struct phy_device *phydev)
 		dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MAX;
 	else if (of_property_read_bool(of_node, "ti,min-output-impedance"))
 		dp83867->io_impedance = DP83867_IO_MUX_CFG_IO_IMPEDANCE_MIN;
+	else
+		dp83867->io_impedance = -1; /* leave at default */
 
 	dp83867->rxctrl_strap_quirk = of_property_read_bool(of_node,
 					"ti,dp83867-rxctrl-strap-quirk");
@@ -333,14 +332,14 @@ static int dp83867_config_init(struct phy_device *phydev)
 
 		phy_write_mmd(phydev, DP83867_DEVADDR, DP83867_RGMIIDCTL,
 			      delay);
-
-		if (dp83867->io_impedance >= 0)
-			phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG,
-				       DP83867_IO_MUX_CFG_IO_IMPEDANCE_CTRL,
-				       dp83867->io_impedance &
-				       DP83867_IO_MUX_CFG_IO_IMPEDANCE_CTRL);
 	}
 
+	/* If specified, set io impedance */
+	if (dp83867->io_impedance >= 0)
+		phy_modify_mmd(phydev, DP83867_DEVADDR, DP83867_IO_MUX_CFG,
+			       DP83867_IO_MUX_CFG_IO_IMPEDANCE_MASK,
+			       dp83867->io_impedance);
+
 	/* Enable Interrupt output INT_OE in CFG3 register */
 	if (phy_interrupt_is_valid(phydev)) {
 		val = phy_read(phydev, DP83867_CFG3);