Merge tag 'hwmon-for-linus-v4.2' of...

Merge tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - new driver for Microchip TC74

 - support for ncpXXwf104 added to ntc_thermistor driver

 - minor cleanup

* tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: add driver for Microchip TC74
  hwmon: (ntc_thermistor) Improve precision of resistance calculation
  hwmon: (ntc_thermistor) fix iio raw to microvolts conversion
  hwmon: (atxp1) Drop auto-detection
  hwmon: (atxp1) Drop FSF mailing address
  hwmon: Allow compile test of GPIO consumers if !GPIOLIB
  hwmon: (sht15) Constify platform_device_id
  hwmon: (max197) Constify platform_device_id
  hwmon: (ntc_thermistor) Add support for ncpXXwf104

Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt

@@ -9,6 +9,7 @@ Requires node properties:
 	"murata,ncp21wb473"
 	"murata,ncp03wb473"
 	"murata,ncp15wl333"
+	"murata,ncp03wf104"
 
 /* Usage of vendor name "ntc" is deprecated */
 <DEPRECATED>	"ntc,ncp15wb473"

Documentation/hwmon/ntc_thermistor

@@ -2,8 +2,10 @@ Kernel driver ntc_thermistor
 =================
 
 Supported thermistors from Murata:
-* Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333
-  Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', 'ncp15wl333'
+* Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473,
+  NCP15WL333, NCP03WF104
+  Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473',
+  'ncp15wl333', 'ncp03wf104'
   Datasheet: Publicly available at Murata
 
 Supported thermistors from EPCOS:

Documentation/hwmon/tc74

+Kernel driver tc74
+====================
+
+Supported chips:
+   * Microchip TC74
+     Prefix: 'tc74'
+     Datasheet: Publicly available at Microchip website.
+
+Description
+-----------
+
+Driver supports the above part.
+
+The tc74 has an 8-bit sensor, with 1 degree centigrade resolution
+and +- 2 degrees centigrade accuracy.
+
+Notes
+-----
+
+Currently entering low power standby mode is not supported.

drivers/hwmon/Kconfig

@@ -509,7 +509,7 @@ config SENSORS_G762
 
 config SENSORS_GPIO_FAN
 	tristate "GPIO fan"
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	depends on THERMAL || THERMAL=n
 	help
 	  If you say yes here you get support for fans connected to GPIO lines.
@@ -1106,8 +1106,8 @@ config SENSORS_NTC_THERMISTOR
 	  send notifications about the temperature.
 
 	  Currently, this driver supports
-	  NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, and NCP15WL333
-	  from Murata and B57330V2103 from EPCOS.
+	  NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333,
+	  and NCP03WF104 from Murata and B57330V2103 from EPCOS.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called ntc-thermistor.
@@ -1186,7 +1186,7 @@ config SENSORS_PWM_FAN
 
 config SENSORS_SHT15
 	tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	help
 	  If you say yes here you get support for the Sensiron SHT10, SHT11,
 	  SHT15, SHT71, SHT75 humidity and temperature sensors.
@@ -1452,6 +1452,16 @@ config SENSORS_INA2XX
 	  This driver can also be built as a module.  If so, the module
 	  will be called ina2xx.
 
+config SENSORS_TC74
+	tristate "Microchip TC74"
+	depends on I2C
+	help
+	  If you say yes here you get support for Microchip TC74 single
+	  input temperature sensor chips.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called tc74.
+
 config SENSORS_THMC50
 	tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
 	depends on I2C

drivers/hwmon/Makefile

@@ -140,6 +140,7 @@ obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
 obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
 obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
 obj-$(CONFIG_SENSORS_AMC6821)	+= amc6821.o
+obj-$(CONFIG_SENSORS_TC74)	+= tc74.o
 obj-$(CONFIG_SENSORS_THMC50)	+= thmc50.o
 obj-$(CONFIG_SENSORS_TMP102)	+= tmp102.o
 obj-$(CONFIG_SENSORS_TMP103)	+= tmp103.o

drivers/hwmon/atxp1.c

@@ -12,10 +12,9 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
+ * The ATXP1 can reside on I2C addresses 0x37 or 0x4e. The chip is
+ * not auto-detected by the driver and must be instantiated explicitly.
+ * See Documentation/i2c/instantiating-devices for more information.
  */
 
 #include <linux/kernel.h>
@@ -43,8 +42,6 @@ MODULE_AUTHOR("Sebastian Witt <se.witt@gmx.net>");
 #define ATXP1_VIDMASK	0x1f
 #define ATXP1_GPIO1MASK	0x0f
 
-static const unsigned short normal_i2c[] = { 0x37, 0x4e, I2C_CLIENT_END };
-
 struct atxp1_data {
 	struct i2c_client *client;
 	struct mutex update_lock;
@@ -259,48 +256,6 @@ static struct attribute *atxp1_attrs[] = {
 };
 ATTRIBUTE_GROUPS(atxp1);
 
-/* Return 0 if detection is successful, -ENODEV otherwise */
-static int atxp1_detect(struct i2c_client *new_client,
-			struct i2c_board_info *info)
-{
-	struct i2c_adapter *adapter = new_client->adapter;
-
-	u8 temp;
-
-	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
-		return -ENODEV;
-
-	/* Detect ATXP1, checking if vendor ID registers are all zero */
-	if (!((i2c_smbus_read_byte_data(new_client, 0x3e) == 0) &&
-	     (i2c_smbus_read_byte_data(new_client, 0x3f) == 0) &&
-	     (i2c_smbus_read_byte_data(new_client, 0xfe) == 0) &&
-	     (i2c_smbus_read_byte_data(new_client, 0xff) == 0)))
-		return -ENODEV;
-
-	/*
-	 * No vendor ID, now checking if registers 0x10,0x11 (non-existent)
-	 * showing the same as register 0x00
-	 */
-	temp = i2c_smbus_read_byte_data(new_client, 0x00);
-
-	if (!((i2c_smbus_read_byte_data(new_client, 0x10) == temp) &&
-	      (i2c_smbus_read_byte_data(new_client, 0x11) == temp)))
-		return -ENODEV;
-
-	/* Get VRM */
-	temp = vid_which_vrm();
-
-	if ((temp != 90) && (temp != 91)) {
-		dev_err(&adapter->dev, "atxp1: Not supporting VRM %d.%d\n",
-				temp / 10, temp % 10);
-		return -ENODEV;
-	}
-
-	strlcpy(info->type, "atxp1", I2C_NAME_SIZE);
-
-	return 0;
-}
-
 static int atxp1_probe(struct i2c_client *client,
 		       const struct i2c_device_id *id)
 {
@@ -314,6 +269,11 @@ static int atxp1_probe(struct i2c_client *client,
 
 	/* Get VRM */
 	data->vrm = vid_which_vrm();
+	if (data->vrm != 90 && data->vrm != 91) {
+		dev_err(dev, "atxp1: Not supporting VRM %d.%d\n",
+			data->vrm / 10, data->vrm % 10);
+		return -ENODEV;
+	}
 
 	data->client = client;
 	mutex_init(&data->update_lock);
@@ -342,8 +302,6 @@ static struct i2c_driver atxp1_driver = {
 	},
 	.probe		= atxp1_probe,
 	.id_table	= atxp1_id,
-	.detect		= atxp1_detect,
-	.address_list	= normal_i2c,
 };
 
 module_i2c_driver(atxp1_driver);

drivers/hwmon/max197.c

@@ -324,7 +324,7 @@ static int max197_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static struct platform_device_id max197_device_ids[] = {
+static const struct platform_device_id max197_device_ids[] = {
 	{ "max197", max197 },
 	{ "max199", max199 },
 	{ }

drivers/hwmon/ntc_thermistor.c

@@ -53,6 +53,7 @@ static const struct platform_device_id ntc_thermistor_id[] = {
 	{ "ncp03wb473", TYPE_NCPXXWB473 },
 	{ "ncp15wl333", TYPE_NCPXXWL333 },
 	{ "b57330v2103", TYPE_B57330V2103},
+	{ "ncp03wf104", TYPE_NCPXXWF104 },
 	{ },
 };
 
@@ -135,6 +136,43 @@ static const struct ntc_compensation ncpXXwl333[] = {
 	{ .temp_c	= 125, .ohm	= 707 },
 };
 
+static const struct ntc_compensation ncpXXwf104[] = {
+	{ .temp_c	= -40, .ohm	= 4397119 },
+	{ .temp_c	= -35, .ohm	= 3088599 },
+	{ .temp_c	= -30, .ohm	= 2197225 },
+	{ .temp_c	= -25, .ohm	= 1581881 },
+	{ .temp_c	= -20, .ohm	= 1151037 },
+	{ .temp_c	= -15, .ohm	= 846579 },
+	{ .temp_c	= -10, .ohm	= 628988 },
+	{ .temp_c	= -5, .ohm	= 471632 },
+	{ .temp_c	= 0, .ohm	= 357012 },
+	{ .temp_c	= 5, .ohm	= 272500 },
+	{ .temp_c	= 10, .ohm	= 209710 },
+	{ .temp_c	= 15, .ohm	= 162651 },
+	{ .temp_c	= 20, .ohm	= 127080 },
+	{ .temp_c	= 25, .ohm	= 100000 },
+	{ .temp_c	= 30, .ohm	= 79222 },
+	{ .temp_c	= 35, .ohm	= 63167 },
+	{ .temp_c	= 40, .ohm	= 50677 },
+	{ .temp_c	= 45, .ohm	= 40904 },
+	{ .temp_c	= 50, .ohm	= 33195 },
+	{ .temp_c	= 55, .ohm	= 27091 },
+	{ .temp_c	= 60, .ohm	= 22224 },
+	{ .temp_c	= 65, .ohm	= 18323 },
+	{ .temp_c	= 70, .ohm	= 15184 },
+	{ .temp_c	= 75, .ohm	= 12635 },
+	{ .temp_c	= 80, .ohm	= 10566 },
+	{ .temp_c	= 85, .ohm	= 8873 },
+	{ .temp_c	= 90, .ohm	= 7481 },
+	{ .temp_c	= 95, .ohm	= 6337 },
+	{ .temp_c	= 100, .ohm	= 5384 },
+	{ .temp_c	= 105, .ohm	= 4594 },
+	{ .temp_c	= 110, .ohm	= 3934 },
+	{ .temp_c	= 115, .ohm	= 3380 },
+	{ .temp_c	= 120, .ohm	= 2916 },
+	{ .temp_c	= 125, .ohm	= 2522 },
+};
+
 /*
  * The following compensation table is from the specification of EPCOS NTC
  * Thermistors Datasheet
@@ -190,20 +228,21 @@ struct ntc_data {
 static int ntc_adc_iio_read(struct ntc_thermistor_platform_data *pdata)
 {
 	struct iio_channel *channel = pdata->chan;
-	s64 result;
-	int val, ret;
+	int raw, uv, ret;
 
-	ret = iio_read_channel_raw(channel, &val);
+	ret = iio_read_channel_raw(channel, &raw);
 	if (ret < 0) {
 		pr_err("read channel() error: %d\n", ret);
 		return ret;
 	}
 
-	/* unit: mV */
-	result = pdata->pullup_uv * (s64) val;
-	result >>= 12;
+	ret = iio_convert_raw_to_processed(channel, raw, &uv, 1000);
+	if (ret < 0) {
+		/* Assume 12 bit ADC with vref at pullup_uv */
+		uv = (pdata->pullup_uv * (s64)raw) >> 12;
+	}
 
-	return (int)result;
+	return uv;
 }
 
 static const struct of_device_id ntc_match[] = {
@@ -219,6 +258,8 @@ static const struct of_device_id ntc_match[] = {
 		.data = &ntc_thermistor_id[4] },
 	{ .compatible = "epcos,b57330v2103",
 		.data = &ntc_thermistor_id[5]},
+	{ .compatible = "murata,ncp03wf104",
+		.data = &ntc_thermistor_id[6] },
 
 	/* Usage of vendor name "ntc" is deprecated */
 	{ .compatible = "ntc,ncp15wb473",
@@ -309,30 +350,27 @@ static inline u64 div64_u64_safe(u64 dividend, u64 divisor)
 static int get_ohm_of_thermistor(struct ntc_data *data, unsigned int uv)
 {
 	struct ntc_thermistor_platform_data *pdata = data->pdata;
-	u64 mv = uv / 1000;
-	u64 pmv = pdata->pullup_uv / 1000;
+	u32 puv = pdata->pullup_uv;
 	u64 n, puo, pdo;
 	puo = pdata->pullup_ohm;
 	pdo = pdata->pulldown_ohm;
 
-	if (mv == 0) {
-		if (pdata->connect == NTC_CONNECTED_POSITIVE)
-			return INT_MAX;
-		return 0;
-	}
-	if (mv >= pmv)
+	if (uv == 0)
+		return (pdata->connect == NTC_CONNECTED_POSITIVE) ?
+			INT_MAX : 0;
+	if (uv >= puv)
 		return (pdata->connect == NTC_CONNECTED_POSITIVE) ?
 			0 : INT_MAX;
 
 	if (pdata->connect == NTC_CONNECTED_POSITIVE && puo == 0)
-		n = div64_u64_safe(pdo * (pmv - mv), mv);
+		n = div_u64(pdo * (puv - uv), uv);
 	else if (pdata->connect == NTC_CONNECTED_GROUND && pdo == 0)
-		n = div64_u64_safe(puo * mv, pmv - mv);
+		n = div_u64(puo * uv, puv - uv);
 	else if (pdata->connect == NTC_CONNECTED_POSITIVE)
-		n = div64_u64_safe(pdo * puo * (pmv - mv),
-				puo * mv - pdo * (pmv - mv));
+		n = div64_u64_safe(pdo * puo * (puv - uv),
+				puo * uv - pdo * (puv - uv));
 	else
-		n = div64_u64_safe(pdo * puo * mv, pdo * (pmv - mv) - puo * mv);
+		n = div64_u64_safe(pdo * puo * uv, pdo * (puv - uv) - puo * uv);
 
 	if (n > INT_MAX)
 		n = INT_MAX;
@@ -567,6 +605,10 @@ static int ntc_thermistor_probe(struct platform_device *pdev)
 		data->comp = b57330v2103;
 		data->n_comp = ARRAY_SIZE(b57330v2103);
 		break;
+	case TYPE_NCPXXWF104:
+		data->comp = ncpXXwf104;
+		data->n_comp = ARRAY_SIZE(ncpXXwf104);
+		break;
 	default:
 		dev_err(&pdev->dev, "Unknown device type: %lu(%s)\n",
 				pdev_id->driver_data, pdev_id->name);

drivers/hwmon/sht15.c

@@ -1074,7 +1074,7 @@ static int sht15_remove(struct platform_device *pdev)
 	return 0;
 }
 
-static struct platform_device_id sht15_device_ids[] = {
+static const struct platform_device_id sht15_device_ids[] = {
 	{ "sht10", sht10 },
 	{ "sht11", sht11 },
 	{ "sht15", sht15 },

drivers/hwmon/tc74.c

+/*
+ * An hwmon driver for the Microchip TC74
+ *
+ * Copyright 2015 Maciej Szmigiero <mail@maciej.szmigiero.name>
+ *
+ * Based on ad7414.c:
+ *	Copyright 2006 Stefan Roese, DENX Software Engineering
+ *	Copyright 2008 Sean MacLennan, PIKA Technologies
+ *	Copyright 2008 Frank Edelhaeuser, Spansion Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/i2c.h>
+#include <linux/jiffies.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/sysfs.h>
+
+/* TC74 registers */
+#define TC74_REG_TEMP		0x00
+#define TC74_REG_CONFIG		0x01
+
+struct tc74_data {
+	struct i2c_client	*client;
+	struct mutex		lock;	/* atomic read data updates */
+	bool			valid;	/* validity of fields below */
+	unsigned long		next_update;	/* In jiffies */
+	s8			temp_input;	/* Temp value in dC */
+};
+
+static int tc74_update_device(struct device *dev)
+{
+	struct tc74_data *data = dev_get_drvdata(dev);
+	struct i2c_client *client = data->client;
+	int ret;
+
+	ret = mutex_lock_interruptible(&data->lock);
+	if (ret)
+		return ret;
+
+	if (time_after(jiffies, data->next_update) || !data->valid) {
+		s32 value;
+
+		value = i2c_smbus_read_byte_data(client, TC74_REG_CONFIG);
+		if (value < 0) {
+			dev_dbg(&client->dev, "TC74_REG_CONFIG read err %d\n",
+				(int)value);
+
+			ret = value;
+			goto ret_unlock;
+		}
+
+		if (!(value & BIT(6))) {
+			/* not ready yet */
+
+			ret = -EAGAIN;
+			goto ret_unlock;
+		}
+
+		value = i2c_smbus_read_byte_data(client, TC74_REG_TEMP);
+		if (value < 0) {
+			dev_dbg(&client->dev, "TC74_REG_TEMP read err %d\n",
+				(int)value);
+
+			ret = value;
+			goto ret_unlock;
+		}
+
+		data->temp_input = value;
+		data->next_update = jiffies + HZ / 4;
+		data->valid = true;
+	}
+
+ret_unlock:
+	mutex_unlock(&data->lock);
+
+	return ret;
+}
+
+static ssize_t show_temp_input(struct device *dev,
+			       struct device_attribute *attr, char *buf)
+{
+	struct tc74_data *data = dev_get_drvdata(dev);
+	int ret;
+
+	ret = tc74_update_device(dev);
+	if (ret)
+		return ret;
+
+	return sprintf(buf, "%d\n", data->temp_input * 1000);
+}
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_input, NULL, 0);
+
+static struct attribute *tc74_attrs[] = {
+	&sensor_dev_attr_temp1_input.dev_attr.attr,
+	NULL
+};
+
+ATTRIBUTE_GROUPS(tc74);
+
+static int tc74_probe(struct i2c_client *client,
+		      const struct i2c_device_id *dev_id)
+{
+	struct device *dev = &client->dev;
+	struct tc74_data *data;
+	struct device *hwmon_dev;
+	s32 conf;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+		return -EOPNOTSUPP;
+
+	data = devm_kzalloc(dev, sizeof(struct tc74_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->client = client;
+	mutex_init(&data->lock);
+
+	/* Make sure the chip is powered up. */
+	conf = i2c_smbus_read_byte_data(client, TC74_REG_CONFIG);
+	if (conf < 0) {
+		dev_err(dev, "unable to read config register\n");
+
+		return conf;
+	}
+
+	if (conf & 0x3f) {
+		dev_err(dev, "invalid config register value\n");
+
+		return -ENODEV;
+	}
+
+	if (conf & BIT(7)) {
+		s32 ret;
+
+		conf &= ~BIT(7);
+
+		ret = i2c_smbus_write_byte_data(client, TC74_REG_CONFIG, conf);
+		if (ret)
+			dev_warn(dev, "unable to disable STANDBY\n");
+	}
+
+	hwmon_dev = devm_hwmon_device_register_with_groups(dev,
+							   client->name,
+							   data, tc74_groups);
+	return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+static const struct i2c_device_id tc74_id[] = {
+	{ "tc74", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, tc74_id);
+
+static struct i2c_driver tc74_driver = {
+	.driver = {
+		.name	= "tc74",
+	},
+	.probe	= tc74_probe,
+	.id_table = tc74_id,
+};
+
+module_i2c_driver(tc74_driver);
+
+MODULE_AUTHOR("Maciej Szmigiero <mail@maciej.szmigiero.name>");
+
+MODULE_DESCRIPTION("TC74 driver");
+MODULE_LICENSE("GPL");

include/linux/platform_data/ntc_thermistor.h

@@ -27,6 +27,7 @@ enum ntc_thermistor_type {
 	TYPE_NCPXXWB473,
 	TYPE_NCPXXWL333,
 	TYPE_B57330V2103,
+	TYPE_NCPXXWF104,
 };
 
 struct ntc_thermistor_platform_data {