提交 215a004c 编写于 作者: D David S. Miller

Merge tag 'linux-can-fixes-for-3.17-20140821' of git://gitorious.org/linux-can/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2014-08-21

The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
......@@ -280,7 +280,7 @@ static int c_can_plat_probe(struct platform_device *pdev)
priv->raminit_ctrlreg = devm_ioremap(&pdev->dev, res->start,
resource_size(res));
if (IS_ERR(priv->raminit_ctrlreg) || priv->instance < 0)
if (!priv->raminit_ctrlreg || priv->instance < 0)
dev_info(&pdev->dev, "control memory is not used for raminit\n");
else
priv->raminit = c_can_hw_raminit_ti;
......
......@@ -549,6 +549,13 @@ static void do_state(struct net_device *dev,
/* process state changes depending on the new state */
switch (new_state) {
case CAN_STATE_ERROR_WARNING:
netdev_dbg(dev, "Error Warning\n");
cf->can_id |= CAN_ERR_CRTL;
cf->data[1] = (bec.txerr > bec.rxerr) ?
CAN_ERR_CRTL_TX_WARNING :
CAN_ERR_CRTL_RX_WARNING;
break;
case CAN_STATE_ERROR_ACTIVE:
netdev_dbg(dev, "Error Active\n");
cf->can_id |= CAN_ERR_PROT;
......@@ -852,6 +859,8 @@ static int flexcan_chip_start(struct net_device *dev)
if (priv->devtype_data->features & FLEXCAN_HAS_BROKEN_ERR_STATE ||
priv->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)
reg_ctrl |= FLEXCAN_CTRL_ERR_MSK;
else
reg_ctrl &= ~FLEXCAN_CTRL_ERR_MSK;
/* save for later use */
priv->reg_ctrl_default = reg_ctrl;
......
......@@ -172,6 +172,35 @@ static void set_normal_mode(struct net_device *dev)
netdev_err(dev, "setting SJA1000 into normal mode failed!\n");
}
/*
* initialize SJA1000 chip:
* - reset chip
* - set output mode
* - set baudrate
* - enable interrupts
* - start operating mode
*/
static void chipset_init(struct net_device *dev)
{
struct sja1000_priv *priv = netdev_priv(dev);
/* set clock divider and output control register */
priv->write_reg(priv, SJA1000_CDR, priv->cdr | CDR_PELICAN);
/* set acceptance filter (accept all) */
priv->write_reg(priv, SJA1000_ACCC0, 0x00);
priv->write_reg(priv, SJA1000_ACCC1, 0x00);
priv->write_reg(priv, SJA1000_ACCC2, 0x00);
priv->write_reg(priv, SJA1000_ACCC3, 0x00);
priv->write_reg(priv, SJA1000_ACCM0, 0xFF);
priv->write_reg(priv, SJA1000_ACCM1, 0xFF);
priv->write_reg(priv, SJA1000_ACCM2, 0xFF);
priv->write_reg(priv, SJA1000_ACCM3, 0xFF);
priv->write_reg(priv, SJA1000_OCR, priv->ocr | OCR_MODE_NORMAL);
}
static void sja1000_start(struct net_device *dev)
{
struct sja1000_priv *priv = netdev_priv(dev);
......@@ -180,6 +209,10 @@ static void sja1000_start(struct net_device *dev)
if (priv->can.state != CAN_STATE_STOPPED)
set_reset_mode(dev);
/* Initialize chip if uninitialized at this stage */
if (!(priv->read_reg(priv, SJA1000_CDR) & CDR_PELICAN))
chipset_init(dev);
/* Clear error counters and error code capture */
priv->write_reg(priv, SJA1000_TXERR, 0x0);
priv->write_reg(priv, SJA1000_RXERR, 0x0);
......@@ -236,35 +269,6 @@ static int sja1000_get_berr_counter(const struct net_device *dev,
return 0;
}
/*
* initialize SJA1000 chip:
* - reset chip
* - set output mode
* - set baudrate
* - enable interrupts
* - start operating mode
*/
static void chipset_init(struct net_device *dev)
{
struct sja1000_priv *priv = netdev_priv(dev);
/* set clock divider and output control register */
priv->write_reg(priv, SJA1000_CDR, priv->cdr | CDR_PELICAN);
/* set acceptance filter (accept all) */
priv->write_reg(priv, SJA1000_ACCC0, 0x00);
priv->write_reg(priv, SJA1000_ACCC1, 0x00);
priv->write_reg(priv, SJA1000_ACCC2, 0x00);
priv->write_reg(priv, SJA1000_ACCC3, 0x00);
priv->write_reg(priv, SJA1000_ACCM0, 0xFF);
priv->write_reg(priv, SJA1000_ACCM1, 0xFF);
priv->write_reg(priv, SJA1000_ACCM2, 0xFF);
priv->write_reg(priv, SJA1000_ACCM3, 0xFF);
priv->write_reg(priv, SJA1000_OCR, priv->ocr | OCR_MODE_NORMAL);
}
/*
* transmit a CAN message
* message layout in the sk_buff should be like this:
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册