thermal: samsung: Add TMU support for Exynos3250 SoC

This patch add registers, bit fields and compatible strings for Exynos3250 TMU
(Thermal Management Unit). Exynos3250 uses the Cortex-A7 dual cores and has
a target speed of 1.0 GHz.
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
[Add MUX address setting bits by Jonghwa Lee]
Signed-off-by: NJonghwa Lee <jonghwa3.lee@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Amit Daniel Kachhap<amit.daniel@samsung.com>
Signed-off-by: NZhang Rui <rui.zhang@intel.com>

Documentation/devicetree/bindings/thermal/exynos-thermal.txt

@@ -3,6 +3,7 @@
 ** Required properties:
 
 - compatible : One of the following:
+	       "samsung,exynos3250-tmu"
 	       "samsung,exynos4412-tmu"
 	       "samsung,exynos4210-tmu"
 	       "samsung,exynos5250-tmu"

drivers/thermal/samsung/exynos_tmu.c

@@ -504,6 +504,10 @@ static irqreturn_t exynos_tmu_irq(int irq, void *id)
 }
 
 static const struct of_device_id exynos_tmu_match[] = {
+	{
+		.compatible = "samsung,exynos3250-tmu",
+		.data = (void *)EXYNOS3250_TMU_DRV_DATA,
+	},
 	{
 		.compatible = "samsung,exynos4210-tmu",
 		.data = (void *)EXYNOS4210_TMU_DRV_DATA,
@@ -677,7 +681,8 @@ static int exynos_tmu_probe(struct platform_device *pdev)
 		goto err_clk_sec;
 	}
 
-	if (pdata->type == SOC_ARCH_EXYNOS4210 ||
+	if (pdata->type == SOC_ARCH_EXYNOS3250 ||
+	    pdata->type == SOC_ARCH_EXYNOS4210 ||
 	    pdata->type == SOC_ARCH_EXYNOS4412 ||
 	    pdata->type == SOC_ARCH_EXYNOS5250 ||
 	    pdata->type == SOC_ARCH_EXYNOS5260 ||

drivers/thermal/samsung/exynos_tmu.h

@@ -40,7 +40,8 @@ enum calibration_mode {
 };
 
 enum soc_type {
-	SOC_ARCH_EXYNOS4210 = 1,
+	SOC_ARCH_EXYNOS3250 = 1,
+	SOC_ARCH_EXYNOS4210,
 	SOC_ARCH_EXYNOS4412,
 	SOC_ARCH_EXYNOS5250,
 	SOC_ARCH_EXYNOS5260,

drivers/thermal/samsung/exynos_tmu_data.c

@@ -90,6 +90,95 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = {
 };
 #endif
 
+#if defined(CONFIG_SOC_EXYNOS3250)
+static const struct exynos_tmu_registers exynos3250_tmu_registers = {
+	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,
+	.triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT,
+	.triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT,
+	.tmu_ctrl = EXYNOS_TMU_REG_CONTROL,
+	.test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT,
+	.buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT,
+	.buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK,
+	.therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT,
+	.therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK,
+	.therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT,
+	.buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT,
+	.buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK,
+	.core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT,
+	.tmu_status = EXYNOS_TMU_REG_STATUS,
+	.tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP,
+	.threshold_th0 = EXYNOS_THD_TEMP_RISE,
+	.threshold_th1 = EXYNOS_THD_TEMP_FALL,
+	.tmu_inten = EXYNOS_TMU_REG_INTEN,
+	.inten_rise0_shift = EXYNOS_TMU_INTEN_RISE0_SHIFT,
+	.inten_rise1_shift = EXYNOS_TMU_INTEN_RISE1_SHIFT,
+	.inten_rise2_shift = EXYNOS_TMU_INTEN_RISE2_SHIFT,
+	.inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT,
+	.tmu_intstat = EXYNOS_TMU_REG_INTSTAT,
+	.tmu_intclear = EXYNOS_TMU_REG_INTCLEAR,
+	.intclr_fall_shift = EXYNOS_TMU_CLEAR_FALL_INT_SHIFT,
+	.intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT,
+	.intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK,
+	.intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK,
+	.emul_con = EXYNOS_EMUL_CON,
+	.emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT,
+	.emul_time_shift = EXYNOS_EMUL_TIME_SHIFT,
+	.emul_time_mask = EXYNOS_EMUL_TIME_MASK,
+};
+
+#define EXYNOS3250_TMU_DATA \
+	.threshold_falling = 10, \
+	.trigger_levels[0] = 70, \
+	.trigger_levels[1] = 95, \
+	.trigger_levels[2] = 110, \
+	.trigger_levels[3] = 120, \
+	.trigger_enable[0] = true, \
+	.trigger_enable[1] = true, \
+	.trigger_enable[2] = true, \
+	.trigger_enable[3] = false, \
+	.trigger_type[0] = THROTTLE_ACTIVE, \
+	.trigger_type[1] = THROTTLE_ACTIVE, \
+	.trigger_type[2] = SW_TRIP, \
+	.trigger_type[3] = HW_TRIP, \
+	.max_trigger_level = 4, \
+	.gain = 8, \
+	.reference_voltage = 16, \
+	.noise_cancel_mode = 4, \
+	.cal_type = TYPE_TWO_POINT_TRIMMING, \
+	.efuse_value = 55, \
+	.min_efuse_value = 40, \
+	.max_efuse_value = 100, \
+	.first_point_trim = 25, \
+	.second_point_trim = 85, \
+	.default_temp_offset = 50, \
+	.freq_tab[0] = { \
+		.freq_clip_max = 800 * 1000, \
+		.temp_level = 70, \
+	}, \
+	.freq_tab[1] = { \
+		.freq_clip_max = 400 * 1000, \
+		.temp_level = 95, \
+	}, \
+	.freq_tab_count = 2, \
+	.registers = &exynos3250_tmu_registers, \
+	.features = (TMU_SUPPORT_EMULATION | \
+			TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \
+			TMU_SUPPORT_EMUL_TIME)
+#endif
+
+#if defined(CONFIG_SOC_EXYNOS3250)
+struct exynos_tmu_init_data const exynos3250_default_tmu_data = {
+	.tmu_data = {
+		{
+			EXYNOS3250_TMU_DATA,
+			.type = SOC_ARCH_EXYNOS3250,
+			.test_mux = EXYNOS4412_MUX_ADDR_VALUE,
+		},
+	},
+	.tmu_count = 1,
+};
+#endif
+
 #if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250)
 static const struct exynos_tmu_registers exynos4412_tmu_registers = {
 	.triminfo_data = EXYNOS_TMU_REG_TRIMINFO,

drivers/thermal/samsung/exynos_tmu_data.h

@@ -148,6 +148,13 @@
 #define EXYNOS5440_TMU_TH_RISE4_SHIFT		24
 #define EXYNOS5440_EFUSE_SWAP_OFFSET		8
 
+#if defined(CONFIG_SOC_EXYNOS3250)
+extern struct exynos_tmu_init_data const exynos3250_default_tmu_data;
+#define EXYNOS3250_TMU_DRV_DATA (&exynos3250_default_tmu_data)
+#else
+#define EXYNOS3250_TMU_DRV_DATA (NULL)
+#endif
+
 #if defined(CONFIG_CPU_EXYNOS4210)
 extern struct exynos_tmu_init_data const exynos4210_default_tmu_data;
 #define EXYNOS4210_TMU_DRV_DATA (&exynos4210_default_tmu_data)