spi: remove sirf prima/atlas driver

The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.

Cc: Barry Song <baohua@kernel.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NBarry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120161658.3820610-1-arnd@kernel.orgSigned-off-by: NMark Brown <broonie@kernel.org>

Documentation/devicetree/bindings/spi/spi-sirf.txt

-* CSR SiRFprimaII Serial Peripheral Interface
-
-Required properties:
-- compatible : Should be "sirf,prima2-spi", "sirf,prima2-usp"
-               or "sirf,atlas7-usp"
-- reg : Offset and length of the register set for the device
-- interrupts : Should contain SPI interrupt
-- resets: phandle to the reset controller asserting this device in
-          reset
-  See ../reset/reset.txt for details.
-- dmas : Must contain an entry for each entry in clock-names.
-  See ../dma/dma.txt for details.
-- dma-names : Must include the following entries:
-  - rx
-  - tx
-- clocks : Must contain an entry for each entry in clock-names.
-  See ../clocks/clock-bindings.txt for details.
-
-- #address-cells: Number of cells required to define a chip select
-                  address on the SPI bus. Should be set to 1.
-- #size-cells:    Should be zero.
-
-Optional properties:
-- spi-max-frequency: Specifies maximum SPI clock frequency,
-                     Units - Hz. Definition as per
-                     Documentation/devicetree/bindings/spi/spi-bus.txt
-- cs-gpios:     should specify GPIOs used for chipselects.
-
-Example:
-
-spi0: spi@b00d0000 {
-	compatible = "sirf,prima2-spi";
-	reg = <0xb00d0000 0x10000>;
-	interrupts = <15>;
-	dmas = <&dmac1 9>,
-		<&dmac1 4>;
-	dma-names = "rx", "tx";
-	#address-cells = <1>;
-	#size-cells = <0>;
-	clocks = <&clks 19>;
-	resets = <&rstc 26>;
-};

drivers/spi/Kconfig

@@ -744,13 +744,6 @@ config SPI_SIFIVE
 	help
 	  This exposes the SPI controller IP from SiFive.
 
-config SPI_SIRF
-	tristate "CSR SiRFprimaII SPI controller"
-	depends on SIRF_DMA
-	select SPI_BITBANG
-	help
-	  SPI driver for CSR SiRFprimaII SoCs
-
 config SPI_SLAVE_MT27XX
 	tristate "MediaTek SPI slave device"
 	depends on ARCH_MEDIATEK || COMPILE_TEST

drivers/spi/Makefile

@@ -104,7 +104,6 @@ obj-$(CONFIG_SPI_SH_HSPI)		+= spi-sh-hspi.o
 obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
 obj-$(CONFIG_SPI_SIFIVE)		+= spi-sifive.o
-obj-$(CONFIG_SPI_SIRF)		+= spi-sirf.o
 obj-$(CONFIG_SPI_SLAVE_MT27XX)          += spi-slave-mt27xx.o
 obj-$(CONFIG_SPI_SPRD)			+= spi-sprd.o
 obj-$(CONFIG_SPI_SPRD_ADI)		+= spi-sprd-adi.o