i2c-cht-wc: Add Intel Cherry Trail Whiskey Cove SMBUS controller driver

The Intel Cherry Trail Whiskey Cove PMIC does not contain a builtin
battery charger, instead boards with this PMIC use an external TI
bq24292i charger IC, which is connected to a SMBUS controller built into
the PMIC.

This commit adds an i2c-bus driver for the PMIC's builtin SMBUS
controller. The probe function for this i2c-bus will also register an
i2c-client for the TI bq24292i charger after the i2c-bus has been
registered.

Note that several device-properties are set on the client-device to
tell the bq24190 power-supply driver to integrate the Whiskey Cove PMIC
and e.g. use the PMIC's BC1.2 detection (through extcon) to determine
the maximum input current.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

drivers/i2c/busses/Kconfig

@@ -189,6 +189,14 @@ config I2C_PIIX4
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-piix4.
 
+config I2C_CHT_WC
+	tristate "Intel Cherry Trail Whiskey Cove PMIC smbus controller"
+	depends on INTEL_SOC_PMIC_CHTWC
+	help
+	  If you say yes to this option, support will be included for the
+	  SMBus controller found in the Intel Cherry Trail Whiskey Cove PMIC
+	  found on some Intel Cherry Trail systems.
+
 config I2C_NFORCE2
 	tristate "Nvidia nForce2, nForce3 and nForce4"
 	depends on PCI

drivers/i2c/busses/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_I2C_ALI15X3)	+= i2c-ali15x3.o
 obj-$(CONFIG_I2C_AMD756)	+= i2c-amd756.o
 obj-$(CONFIG_I2C_AMD756_S4882)	+= i2c-amd756-s4882.o
 obj-$(CONFIG_I2C_AMD8111)	+= i2c-amd8111.o
+obj-$(CONFIG_I2C_CHT_WC)	+= i2c-cht-wc.o
 obj-$(CONFIG_I2C_I801)		+= i2c-i801.o
 obj-$(CONFIG_I2C_ISCH)		+= i2c-isch.o
 obj-$(CONFIG_I2C_ISMT)		+= i2c-ismt.o

drivers/i2c/busses/i2c-cht-wc.c

+/*
+ * Intel CHT Whiskey Cove PMIC I2C Master driver
+ * Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Based on various non upstream patches to support the CHT Whiskey Cove PMIC:
+ * Copyright (C) 2011 - 2014 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version
+ * 2 as published by the Free Software Foundation, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define CHT_WC_I2C_CTRL			0x5e24
+#define CHT_WC_I2C_CTRL_WR		BIT(0)
+#define CHT_WC_I2C_CTRL_RD		BIT(1)
+#define CHT_WC_I2C_CLIENT_ADDR		0x5e25
+#define CHT_WC_I2C_REG_OFFSET		0x5e26
+#define CHT_WC_I2C_WRDATA		0x5e27
+#define CHT_WC_I2C_RDDATA		0x5e28
+
+#define CHT_WC_EXTCHGRIRQ		0x6e0a
+#define CHT_WC_EXTCHGRIRQ_CLIENT_IRQ	BIT(0)
+#define CHT_WC_EXTCHGRIRQ_WRITE_IRQ	BIT(1)
+#define CHT_WC_EXTCHGRIRQ_READ_IRQ	BIT(2)
+#define CHT_WC_EXTCHGRIRQ_NACK_IRQ	BIT(3)
+#define CHT_WC_EXTCHGRIRQ_ADAP_IRQMASK	((u8)GENMASK(3, 1))
+#define CHT_WC_EXTCHGRIRQ_MSK		0x6e17
+
+struct cht_wc_i2c_adap {
+	struct i2c_adapter adapter;
+	wait_queue_head_t wait;
+	struct irq_chip irqchip;
+	struct mutex irqchip_lock;
+	struct regmap *regmap;
+	struct irq_domain *irq_domain;
+	struct i2c_client *client;
+	int client_irq;
+	u8 irq_mask;
+	u8 old_irq_mask;
+	bool nack;
+	bool done;
+};
+
+static irqreturn_t cht_wc_i2c_adap_thread_handler(int id, void *data)
+{
+	struct cht_wc_i2c_adap *adap = data;
+	int ret, reg;
+
+	/* Read IRQs */
+	ret = regmap_read(adap->regmap, CHT_WC_EXTCHGRIRQ, &reg);
+	if (ret) {
+		dev_err(&adap->adapter.dev, "Error reading extchgrirq reg\n");
+		return IRQ_NONE;
+	}
+
+	reg &= ~adap->irq_mask;
+
+	/*
+	 * Immediately ack IRQs, so that if new IRQs arrives while we're
+	 * handling the previous ones our irq will re-trigger when we're done.
+	 */
+	ret = regmap_write(adap->regmap, CHT_WC_EXTCHGRIRQ, reg);
+	if (ret)
+		dev_err(&adap->adapter.dev, "Error writing extchgrirq reg\n");
+
+	/*
+	 * Do NOT use handle_nested_irq here, the client irq handler will
+	 * likely want to do i2c transfers and the i2c controller uses this
+	 * interrupt handler as well, so running the client irq handler from
+	 * this thread will cause things to lock up.
+	 */
+	if (reg & CHT_WC_EXTCHGRIRQ_CLIENT_IRQ) {
+		/*
+		 * generic_handle_irq expects local IRQs to be disabled
+		 * as normally it is called from interrupt context.
+		 */
+		local_irq_disable();
+		generic_handle_irq(adap->client_irq);
+		local_irq_enable();
+	}
+
+	if (reg & CHT_WC_EXTCHGRIRQ_ADAP_IRQMASK) {
+		adap->nack = !!(reg & CHT_WC_EXTCHGRIRQ_NACK_IRQ);
+		adap->done = true;
+		wake_up(&adap->wait);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static u32 cht_wc_i2c_adap_master_func(struct i2c_adapter *adap)
+{
+	/* This i2c adapter only supports SMBUS byte transfers */
+	return I2C_FUNC_SMBUS_BYTE_DATA;
+}
+
+static int cht_wc_i2c_adap_smbus_xfer(struct i2c_adapter *_adap, u16 addr,
+				      unsigned short flags, char read_write,
+				      u8 command, int size,
+				      union i2c_smbus_data *data)
+{
+	struct cht_wc_i2c_adap *adap = i2c_get_adapdata(_adap);
+	int ret, reg;
+
+	adap->nack = false;
+	adap->done = false;
+
+	ret = regmap_write(adap->regmap, CHT_WC_I2C_CLIENT_ADDR, addr);
+	if (ret)
+		return ret;
+
+	if (read_write == I2C_SMBUS_WRITE) {
+		ret = regmap_write(adap->regmap, CHT_WC_I2C_WRDATA, data->byte);
+		if (ret)
+			return ret;
+	}
+
+	ret = regmap_write(adap->regmap, CHT_WC_I2C_REG_OFFSET, command);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(adap->regmap, CHT_WC_I2C_CTRL,
+			   (read_write == I2C_SMBUS_WRITE) ?
+			   CHT_WC_I2C_CTRL_WR : CHT_WC_I2C_CTRL_RD);
+	if (ret)
+		return ret;
+
+	/* 3 second timeout, during cable plug the PMIC responds quite slow */
+	ret = wait_event_timeout(adap->wait, adap->done, 3 * HZ);
+	if (ret == 0)
+		return -ETIMEDOUT;
+	if (adap->nack)
+		return -EIO;
+
+	if (read_write == I2C_SMBUS_READ) {
+		ret = regmap_read(adap->regmap, CHT_WC_I2C_RDDATA, &reg);
+		if (ret)
+			return ret;
+
+		data->byte = reg;
+	}
+
+	return 0;
+}
+
+static const struct i2c_algorithm cht_wc_i2c_adap_algo = {
+	.functionality = cht_wc_i2c_adap_master_func,
+	.smbus_xfer = cht_wc_i2c_adap_smbus_xfer,
+};
+
+/**** irqchip for the client connected to the extchgr i2c adapter ****/
+static void cht_wc_i2c_irq_lock(struct irq_data *data)
+{
+	struct cht_wc_i2c_adap *adap = irq_data_get_irq_chip_data(data);
+
+	mutex_lock(&adap->irqchip_lock);
+}
+
+static void cht_wc_i2c_irq_sync_unlock(struct irq_data *data)
+{
+	struct cht_wc_i2c_adap *adap = irq_data_get_irq_chip_data(data);
+	int ret;
+
+	if (adap->irq_mask != adap->old_irq_mask) {
+		ret = regmap_write(adap->regmap, CHT_WC_EXTCHGRIRQ_MSK,
+				   adap->irq_mask);
+		if (ret == 0)
+			adap->old_irq_mask = adap->irq_mask;
+		else
+			dev_err(&adap->adapter.dev, "Error writing EXTCHGRIRQ_MSK\n");
+	}
+
+	mutex_unlock(&adap->irqchip_lock);
+}
+
+static void cht_wc_i2c_irq_enable(struct irq_data *data)
+{
+	struct cht_wc_i2c_adap *adap = irq_data_get_irq_chip_data(data);
+
+	adap->irq_mask &= ~CHT_WC_EXTCHGRIRQ_CLIENT_IRQ;
+}
+
+static void cht_wc_i2c_irq_disable(struct irq_data *data)
+{
+	struct cht_wc_i2c_adap *adap = irq_data_get_irq_chip_data(data);
+
+	adap->irq_mask |= CHT_WC_EXTCHGRIRQ_CLIENT_IRQ;
+}
+
+static const struct irq_chip cht_wc_i2c_irq_chip = {
+	.irq_bus_lock		= cht_wc_i2c_irq_lock,
+	.irq_bus_sync_unlock	= cht_wc_i2c_irq_sync_unlock,
+	.irq_disable		= cht_wc_i2c_irq_disable,
+	.irq_enable		= cht_wc_i2c_irq_enable,
+	.name			= "cht_wc_ext_chrg_irq_chip",
+};
+
+static const struct property_entry bq24190_props[] = {
+	PROPERTY_ENTRY_STRING("extcon-name", "cht_wcove_pwrsrc"),
+	PROPERTY_ENTRY_BOOL("omit-battery-class"),
+	PROPERTY_ENTRY_BOOL("disable-reset"),
+	{ }
+};
+
+static int cht_wc_i2c_adap_i2c_probe(struct platform_device *pdev)
+{
+	struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
+	struct cht_wc_i2c_adap *adap;
+	struct i2c_board_info board_info = {
+		.type = "bq24190",
+		.addr = 0x6b,
+		.properties = bq24190_props,
+	};
+	int ret, irq;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Error missing irq resource\n");
+		return -EINVAL;
+	}
+
+	adap = devm_kzalloc(&pdev->dev, sizeof(*adap), GFP_KERNEL);
+	if (!adap)
+		return -ENOMEM;
+
+	init_waitqueue_head(&adap->wait);
+	mutex_init(&adap->irqchip_lock);
+	adap->irqchip = cht_wc_i2c_irq_chip;
+	adap->regmap = pmic->regmap;
+	adap->adapter.owner = THIS_MODULE;
+	adap->adapter.class = I2C_CLASS_HWMON;
+	adap->adapter.algo = &cht_wc_i2c_adap_algo;
+	strlcpy(adap->adapter.name, "PMIC I2C Adapter",
+		sizeof(adap->adapter.name));
+	adap->adapter.dev.parent = &pdev->dev;
+
+	/* Clear and activate i2c-adapter interrupts, disable client IRQ */
+	adap->old_irq_mask = adap->irq_mask = ~CHT_WC_EXTCHGRIRQ_ADAP_IRQMASK;
+	ret = regmap_write(adap->regmap, CHT_WC_EXTCHGRIRQ, ~adap->irq_mask);
+	if (ret)
+		return ret;
+
+	ret = regmap_write(adap->regmap, CHT_WC_EXTCHGRIRQ_MSK, adap->irq_mask);
+	if (ret)
+		return ret;
+
+	/* Alloc and register client IRQ */
+	adap->irq_domain = irq_domain_add_linear(pdev->dev.of_node, 1,
+						 &irq_domain_simple_ops, NULL);
+	if (!adap->irq_domain)
+		return -ENOMEM;
+
+	adap->client_irq = irq_create_mapping(adap->irq_domain, 0);
+	if (!adap->client_irq) {
+		ret = -ENOMEM;
+		goto remove_irq_domain;
+	}
+
+	irq_set_chip_data(adap->client_irq, adap);
+	irq_set_chip_and_handler(adap->client_irq, &adap->irqchip,
+				 handle_simple_irq);
+
+	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+					cht_wc_i2c_adap_thread_handler,
+					IRQF_ONESHOT, "PMIC I2C Adapter", adap);
+	if (ret)
+		goto remove_irq_domain;
+
+	i2c_set_adapdata(&adap->adapter, adap);
+	ret = i2c_add_adapter(&adap->adapter);
+	if (ret)
+		goto remove_irq_domain;
+
+	board_info.irq = adap->client_irq;
+	adap->client = i2c_new_device(&adap->adapter, &board_info);
+	if (!adap->client) {
+		ret = -ENOMEM;
+		goto del_adapter;
+	}
+
+	platform_set_drvdata(pdev, adap);
+	return 0;
+
+del_adapter:
+	i2c_del_adapter(&adap->adapter);
+remove_irq_domain:
+	irq_domain_remove(adap->irq_domain);
+	return ret;
+}
+
+static int cht_wc_i2c_adap_i2c_remove(struct platform_device *pdev)
+{
+	struct cht_wc_i2c_adap *adap = platform_get_drvdata(pdev);
+
+	i2c_unregister_device(adap->client);
+	i2c_del_adapter(&adap->adapter);
+	irq_domain_remove(adap->irq_domain);
+
+	return 0;
+}
+
+static struct platform_device_id cht_wc_i2c_adap_id_table[] = {
+	{ .name = "cht_wcove_ext_chgr" },
+	{},
+};
+MODULE_DEVICE_TABLE(platform, cht_wc_i2c_adap_id_table);
+
+struct platform_driver cht_wc_i2c_adap_driver = {
+	.probe = cht_wc_i2c_adap_i2c_probe,
+	.remove = cht_wc_i2c_adap_i2c_remove,
+	.driver = {
+		.name = "cht_wcove_ext_chgr",
+	},
+	.id_table = cht_wc_i2c_adap_id_table,
+};
+module_platform_driver(cht_wc_i2c_adap_driver);
+
+MODULE_DESCRIPTION("Intel CHT Whiskey Cove PMIC I2C Master driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_LICENSE("GPL");