提交 179ab1cb 编写于 作者: M Michael Ellerman

powerpc/64: Add CONFIG_PPC_BARRIER_NOSPEC

Add a config symbol to encode which platforms support the
barrier_nospec speculation barrier. Currently this is just Book3S 64
but we will add Book3E in a future patch.
Signed-off-by: NDiana Craciun <diana.craciun@nxp.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
上级 6453b532
......@@ -165,7 +165,7 @@ config PPC
select GENERIC_CLOCKEVENTS_BROADCAST if SMP
select GENERIC_CMOS_UPDATE
select GENERIC_CPU_AUTOPROBE
select GENERIC_CPU_VULNERABILITIES if PPC_BOOK3S_64
select GENERIC_CPU_VULNERABILITIES if PPC_BARRIER_NOSPEC
select GENERIC_IRQ_SHOW
select GENERIC_IRQ_SHOW_LEVEL
select GENERIC_SMP_IDLE_THREAD
......@@ -242,6 +242,11 @@ config PPC
# Please keep this list sorted alphabetically.
#
config PPC_BARRIER_NOSPEC
bool
default y
depends on PPC_BOOK3S_64
config GENERIC_CSUM
def_bool n
......
......@@ -78,7 +78,7 @@ do { \
___p1; \
})
#ifdef CONFIG_PPC_BOOK3S_64
#ifdef CONFIG_PPC_BARRIER_NOSPEC
/*
* Prevent execution of subsequent instructions until preceding branches have
* been fully resolved and are no longer executing speculatively.
......@@ -88,10 +88,10 @@ do { \
// This also acts as a compiler barrier due to the memory clobber.
#define barrier_nospec() asm (stringify_in_c(barrier_nospec_asm) ::: "memory")
#else /* !CONFIG_PPC_BOOK3S_64 */
#else /* !CONFIG_PPC_BARRIER_NOSPEC */
#define barrier_nospec_asm
#define barrier_nospec()
#endif
#endif /* CONFIG_PPC_BARRIER_NOSPEC */
#include <asm-generic/barrier.h>
......
......@@ -56,7 +56,7 @@ void setup_barrier_nospec(void);
void do_barrier_nospec_fixups(bool enable);
extern bool barrier_nospec_enabled;
#ifdef CONFIG_PPC_BOOK3S_64
#ifdef CONFIG_PPC_BARRIER_NOSPEC
void do_barrier_nospec_fixups_range(bool enable, void *start, void *end);
#else
static inline void do_barrier_nospec_fixups_range(bool enable, void *start, void *end) { };
......
......@@ -42,9 +42,10 @@ obj-$(CONFIG_VDSO32) += vdso32/
obj-$(CONFIG_PPC_WATCHDOG) += watchdog.o
obj-$(CONFIG_HAVE_HW_BREAKPOINT) += hw_breakpoint.o
obj-$(CONFIG_PPC_BOOK3S_64) += cpu_setup_ppc970.o cpu_setup_pa6t.o
obj-$(CONFIG_PPC_BOOK3S_64) += cpu_setup_power.o security.o
obj-$(CONFIG_PPC_BOOK3S_64) += cpu_setup_power.o
obj-$(CONFIG_PPC_BOOK3S_64) += mce.o mce_power.o
obj-$(CONFIG_PPC_BOOK3E_64) += exceptions-64e.o idle_book3e.o
obj-$(CONFIG_PPC_BARRIER_NOSPEC) += security.o
obj-$(CONFIG_PPC64) += vdso64/
obj-$(CONFIG_ALTIVEC) += vecemu.o
obj-$(CONFIG_PPC_970_NAP) += idle_power4.o
......
......@@ -72,13 +72,15 @@ int module_finalize(const Elf_Ehdr *hdr,
do_feature_fixups(powerpc_firmware_features,
(void *)sect->sh_addr,
(void *)sect->sh_addr + sect->sh_size);
#endif /* CONFIG_PPC64 */
#ifdef CONFIG_PPC_BARRIER_NOSPEC
sect = find_section(hdr, sechdrs, "__spec_barrier_fixup");
if (sect != NULL)
do_barrier_nospec_fixups_range(barrier_nospec_enabled,
(void *)sect->sh_addr,
(void *)sect->sh_addr + sect->sh_size);
#endif
#endif /* CONFIG_PPC_BARRIER_NOSPEC */
sect = find_section(hdr, sechdrs, "__lwsync_fixup");
if (sect != NULL)
......
......@@ -153,14 +153,16 @@ SECTIONS
*(__rfi_flush_fixup)
__stop___rfi_flush_fixup = .;
}
#endif /* CONFIG_PPC64 */
#ifdef CONFIG_PPC_BARRIER_NOSPEC
. = ALIGN(8);
__spec_barrier_fixup : AT(ADDR(__spec_barrier_fixup) - LOAD_OFFSET) {
__start___barrier_nospec_fixup = .;
*(__barrier_nospec_fixup)
__stop___barrier_nospec_fixup = .;
}
#endif
#endif /* CONFIG_PPC_BARRIER_NOSPEC */
EXCEPTION_TABLE(0)
......
......@@ -304,6 +304,9 @@ void do_barrier_nospec_fixups_range(bool enable, void *fixup_start, void *fixup_
printk(KERN_DEBUG "barrier-nospec: patched %d locations\n", i);
}
#endif /* CONFIG_PPC_BOOK3S_64 */
#ifdef CONFIG_PPC_BARRIER_NOSPEC
void do_barrier_nospec_fixups(bool enable)
{
void *start, *end;
......@@ -313,8 +316,7 @@ void do_barrier_nospec_fixups(bool enable)
do_barrier_nospec_fixups_range(enable, start, end);
}
#endif /* CONFIG_PPC_BOOK3S_64 */
#endif /* CONFIG_PPC_BARRIER_NOSPEC */
void do_lwsync_fixups(unsigned long value, void *fixup_start, void *fixup_end)
{
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册