V4L/DVB (11343): au0828: make i2c clock speed per-board configurable

Setup the i2c clock speed to be definable on a per-board basis.  This allows
us to explicitly set the clock speed to 30 KHz on the 950q, and also gets rid
of code which sets it on a basis of what chip the i2c master is talking to
at any given time (which could have caused issues because i2c slaves should
never receive commands at a clock higher than their supported clock speed).
Signed-off-by: NDevin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/au0828/au0828-cards.c

@@ -46,6 +46,7 @@ struct au0828_board au0828_boards[] = {
 		.name	= "Hauppauge HVR850",
 		.tuner_type = TUNER_XC5000,
 		.tuner_addr = 0x61,
+		.i2c_clk_divider = AU0828_I2C_CLK_30KHZ,
 		.input = {
 			{
 				.type = AU0828_VMUX_TELEVISION,
@@ -70,6 +71,13 @@ struct au0828_board au0828_boards[] = {
 		.name	= "Hauppauge HVR950Q",
 		.tuner_type = TUNER_XC5000,
 		.tuner_addr = 0x61,
+		/* The au0828 hardware i2c implementation does not properly
+		   support the xc5000's i2c clock stretching.  So we need to
+		   lower the clock frequency enough where the 15us clock
+		   stretch fits inside of a normal clock cycle, or else the
+		   au0828 fails to set the STOP bit.  A 30 KHz clock puts the
+		   clock pulse width at 18us */
+		.i2c_clk_divider = AU0828_I2C_CLK_30KHZ,
 		.input = {
 			{
 				.type = AU0828_VMUX_TELEVISION,
@@ -94,16 +102,19 @@ struct au0828_board au0828_boards[] = {
 		.name	= "Hauppauge HVR950Q rev xxF8",
 		.tuner_type = UNSET,
 		.tuner_addr = ADDR_UNSET,
+		.i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
 	},
 	[AU0828_BOARD_DVICO_FUSIONHDTV7] = {
 		.name	= "DViCO FusionHDTV USB",
 		.tuner_type = UNSET,
 		.tuner_addr = ADDR_UNSET,
+		.i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
 	},
 	[AU0828_BOARD_HAUPPAUGE_WOODBURY] = {
 		.name = "Hauppauge Woodbury",
 		.tuner_type = UNSET,
 		.tuner_addr = ADDR_UNSET,
+		.i2c_clk_divider = AU0828_I2C_CLK_250KHZ,
 	},
 };
 

drivers/media/video/au0828/au0828-i2c.c

@@ -146,16 +146,9 @@ static int i2c_sendbytes(struct i2c_adapter *i2c_adap,
 
 	au0828_write(dev, AU0828_I2C_MULTIBYTE_MODE_2FF, 0x01);
 
-	/* FIXME: There is a problem with i2c communications with xc5000 that
-	   requires us to slow down the i2c clock until we have a better
-	   strategy (such as using the secondary i2c bus to do firmware
-	   loading */
-	if ((msg->addr << 1) == 0xc2)
-		au0828_write(dev, AU0828_I2C_CLK_DIVIDER_202,
-			     AU0828_I2C_CLK_30KHZ);
-	else
-		au0828_write(dev, AU0828_I2C_CLK_DIVIDER_202,
-			     AU0828_I2C_CLK_250KHZ);
+	/* Set the I2C clock */
+	au0828_write(dev, AU0828_I2C_CLK_DIVIDER_202,
+		     dev->board.i2c_clk_divider);
 
 	/* Hardware needs 8 bit addresses */
 	au0828_write(dev, AU0828_I2C_DEST_ADDR_203, msg->addr << 1);
@@ -230,16 +223,9 @@ static int i2c_readbytes(struct i2c_adapter *i2c_adap,
 
 	au0828_write(dev, AU0828_I2C_MULTIBYTE_MODE_2FF, 0x01);
 
-	/* FIXME: There is a problem with i2c communications with xc5000 that
-	   requires us to slow down the i2c clock until we have a better
-	   strategy (such as using the secondary i2c bus to do firmware
-	   loading */
-	if ((msg->addr << 1) == 0xc2)
-		au0828_write(dev, AU0828_I2C_CLK_DIVIDER_202,
-			     AU0828_I2C_CLK_30KHZ);
-	else
-		au0828_write(dev, AU0828_I2C_CLK_DIVIDER_202,
-			     AU0828_I2C_CLK_250KHZ);
+	/* Set the I2C clock */
+	au0828_write(dev, AU0828_I2C_CLK_DIVIDER_202,
+		     dev->board.i2c_clk_divider);
 
 	/* Hardware needs 8 bit addresses */
 	au0828_write(dev, AU0828_I2C_DEST_ADDR_203, msg->addr << 1);

drivers/media/video/au0828/au0828.h

@@ -81,6 +81,7 @@ struct au0828_board {
 	char *name;
 	unsigned int tuner_type;
 	unsigned char tuner_addr;
+	unsigned char i2c_clk_divider;
 	struct au0828_input input[AU0828_MAX_INPUT];
 
 };