提交 153cb557 编写于 作者: L Larry Finger 提交者: Kalle Valo

rtlwifi: rtl8192ee: Convert driver to use common DM table initialization

Convert driver rtl8192ee to use the common routine to initialize
dm_digtable.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
上级 8b17c1f3
......@@ -152,35 +152,6 @@ static const u8 cckswing_table_ch14[CCK_TABLE_SIZE][8] = {
{0x09, 0x08, 0x07, 0x04, 0x00, 0x00, 0x00, 0x00} /* 32, -16.0dB */
};
static void rtl92ee_dm_diginit(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct dig_t *dm_dig = &rtlpriv->dm_digtable;
dm_dig->cur_igvalue = rtl_get_bbreg(hw, DM_REG_IGI_A_11N,
DM_BIT_IGI_11N);
dm_dig->rssi_lowthresh = DM_DIG_THRESH_LOW;
dm_dig->rssi_highthresh = DM_DIG_THRESH_HIGH;
dm_dig->fa_lowthresh = DM_FALSEALARM_THRESH_LOW;
dm_dig->fa_highthresh = DM_FALSEALARM_THRESH_HIGH;
dm_dig->rx_gain_max = DM_DIG_MAX;
dm_dig->rx_gain_min = DM_DIG_MIN;
dm_dig->back_val = DM_DIG_BACKOFF_DEFAULT;
dm_dig->back_range_max = DM_DIG_BACKOFF_MAX;
dm_dig->back_range_min = DM_DIG_BACKOFF_MIN;
dm_dig->pre_cck_cca_thres = 0xff;
dm_dig->cur_cck_cca_thres = 0x83;
dm_dig->forbidden_igi = DM_DIG_MIN;
dm_dig->large_fa_hit = 0;
dm_dig->recover_cnt = 0;
dm_dig->dig_min_0 = DM_DIG_MIN;
dm_dig->dig_min_1 = DM_DIG_MIN;
dm_dig->media_connect_0 = false;
dm_dig->media_connect_1 = false;
rtlpriv->dm.dm_initialgain_enable = true;
dm_dig->bt30_cur_igi = 0x32;
}
static void rtl92ee_dm_false_alarm_counter_statistics(struct ieee80211_hw *hw)
{
u32 ret_value;
......@@ -1089,10 +1060,11 @@ static void rtl92ee_dm_init_dynamic_atc_switch(struct ieee80211_hw *hw)
void rtl92ee_dm_init(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
u32 cur_igvalue = rtl_get_bbreg(hw, DM_REG_IGI_A_11N, DM_BIT_IGI_11N);
rtlpriv->dm.dm_type = DM_TYPE_BYDRIVER;
rtl92ee_dm_diginit(hw);
rtl_dm_diginit(hw, cur_igvalue);
rtl92ee_dm_init_rate_adaptive_mask(hw);
rtl92ee_dm_init_primary_cca_check(hw);
rtl92ee_dm_init_edca_turbo(hw);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册