提交 15317ab2 编写于 作者: T Takashi Iwai

ALSA: hda/realtek - Replace ALC260 model=acer with the auto-parser

The ALC260 model=acer needs GPIO1 setup.  It could be selected well
if the codec SSID is set properly by BIOS, but to make sure, enable it
forcibly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
上级 ca8f0424
......@@ -30,7 +30,6 @@ ALC880
ALC260
======
fujitsu Fujitsu S7020
acer Acer TravelMate
replacer Replacer 672V
favorit100 Maxdata Favorit 100XS
basic fixed pin assignment (old default model)
......
......@@ -8,7 +8,6 @@ enum {
ALC260_AUTO,
ALC260_BASIC,
ALC260_FUJITSU_S702X,
ALC260_ACER,
ALC260_REPLACER_672V,
ALC260_FAVORIT100,
#ifdef CONFIG_SND_DEBUG
......@@ -181,48 +180,6 @@ static const struct snd_kcontrol_new alc260_fujitsu_mixer[] = {
{ } /* end */
};
/* Mixer for Acer TravelMate(/Extensa/Aspire) notebooks. Note that current
* versions of the ALC260 don't act on requests to enable mic bias from NID
* 0x0f (used to drive the headphone jack in these laptops). The ALC260
* datasheet doesn't mention this restriction. At this stage it's not clear
* whether this behaviour is intentional or is a hardware bug in chip
* revisions available in early 2006. Therefore for now allow the
* "Headphone Jack Mode" control to span all choices, but if it turns out
* that the lack of mic bias for this NID is intentional we could change the
* mode from ALC_PIN_DIR_INOUT to ALC_PIN_DIR_INOUT_NOMICBIAS.
*
* In addition, Acer TravelMate(/Extensa/Aspire) notebooks in early 2006
* don't appear to make the mic bias available from the "line" jack, even
* though the NID used for this jack (0x14) can supply it. The theory is
* that perhaps Acer have included blocking capacitors between the ALC260
* and the output jack. If this turns out to be the case for all such
* models the "Line Jack Mode" mode could be changed from ALC_PIN_DIR_INOUT
* to ALC_PIN_DIR_INOUT_NOMICBIAS.
*
* The C20x Tablet series have a mono internal speaker which is controlled
* via the chip's Mono sum widget and pin complex, so include the necessary
* controls for such models. On models without a "mono speaker" the control
* won't do anything.
*/
static const struct snd_kcontrol_new alc260_acer_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0x08, 0x0, HDA_OUTPUT),
HDA_BIND_MUTE("Master Playback Switch", 0x08, 2, HDA_INPUT),
ALC_PIN_MODE("Headphone Jack Mode", 0x0f, ALC_PIN_DIR_INOUT),
HDA_CODEC_VOLUME_MONO("Speaker Playback Volume", 0x0a, 1, 0x0,
HDA_OUTPUT),
HDA_BIND_MUTE_MONO("Speaker Playback Switch", 0x0a, 1, 2,
HDA_INPUT),
HDA_CODEC_VOLUME("CD Playback Volume", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_MUTE("CD Playback Switch", 0x07, 0x04, HDA_INPUT),
HDA_CODEC_VOLUME("Mic Playback Volume", 0x07, 0x0, HDA_INPUT),
HDA_CODEC_MUTE("Mic Playback Switch", 0x07, 0x0, HDA_INPUT),
ALC_PIN_MODE("Mic Jack Mode", 0x12, ALC_PIN_DIR_IN),
HDA_CODEC_VOLUME("Line Playback Volume", 0x07, 0x02, HDA_INPUT),
HDA_CODEC_MUTE("Line Playback Switch", 0x07, 0x02, HDA_INPUT),
ALC_PIN_MODE("Line Jack Mode", 0x14, ALC_PIN_DIR_INOUT),
{ } /* end */
};
/* Maxdata Favorit 100XS: one output and one input (0x12) jack
*/
static const struct snd_kcontrol_new alc260_favorit100_mixer[] = {
......@@ -401,94 +358,6 @@ static const struct hda_verb alc260_fujitsu_init_verbs[] = {
{ }
};
/* Initialisation sequence for ALC260 as configured in Acer TravelMate and
* similar laptops (adapted from Fujitsu init verbs).
*/
static const struct hda_verb alc260_acer_init_verbs[] = {
/* On TravelMate laptops, GPIO 0 enables the internal speaker and
* the headphone jack. Turn this on and rely on the standard mute
* methods whenever the user wants to turn these outputs off.
*/
{0x01, AC_VERB_SET_GPIO_MASK, 0x01},
{0x01, AC_VERB_SET_GPIO_DIRECTION, 0x01},
{0x01, AC_VERB_SET_GPIO_DATA, 0x01},
/* Internal speaker/Headphone jack is connected to Line-out pin */
{0x0f, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
/* Internal microphone/Mic jack is connected to Mic1 pin */
{0x12, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF50},
/* Line In jack is connected to Line1 pin */
{0x14, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_IN},
/* Some Acers (eg: C20x Tablets) use Mono pin for internal speaker */
{0x11, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_HP},
/* Ensure all other unused pins are disabled and muted. */
{0x10, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x10, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x13, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x13, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x15, AC_VERB_SET_PIN_WIDGET_CONTROL, 0},
{0x15, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Disable digital (SPDIF) pins */
{0x03, AC_VERB_SET_DIGI_CONVERT_1, 0},
{0x06, AC_VERB_SET_DIGI_CONVERT_1, 0},
/* Ensure Mic1 and Line1 pin widgets take input from the OUT1 sum
* bus when acting as outputs.
*/
{0x0b, AC_VERB_SET_CONNECT_SEL, 0},
{0x0d, AC_VERB_SET_CONNECT_SEL, 0},
/* Start with output sum widgets muted and their output gains at min */
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x08, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x09, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)},
{0x0a, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_ZERO},
/* Unmute Line-out pin widget amp left and right
* (no equiv mixer ctrl)
*/
{0x0f, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute mono pin widget amp output (no equiv mixer ctrl) */
{0x11, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_UNMUTE},
/* Unmute Mic1 and Line1 pin widget input buffers since they start as
* inputs. If the pin mode is changed by the user the pin mode control
* will take care of enabling the pin's input/output buffers as needed.
* Therefore there's no need to enable the input buffer at this
* stage.
*/
{0x12, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
{0x14, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_UNMUTE(0)},
/* Mute capture amp left and right */
{0x04, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
/* Set ADC connection select to match default mixer setting - mic
* (on mic1 pin)
*/
{0x04, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Do similar with the second ADC: mute capture input amp and
* set ADC connection to mic to match ALSA's default state.
*/
{0x05, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)},
{0x05, AC_VERB_SET_CONNECT_SEL, 0x00},
/* Mute all inputs to mixer widget (even unconnected ones) */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(0)}, /* mic1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(1)}, /* mic2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(2)}, /* line1 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(3)}, /* line2 pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(4)}, /* CD pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(5)}, /* Beep-gen pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(6)}, /* Line-out pin */
{0x07, AC_VERB_SET_AMP_GAIN_MUTE, AMP_IN_MUTE(7)}, /* HP-pin pin */
{ }
};
/* Initialisation sequence for Maxdata Favorit 100XS
* (adapted from Acer init verbs).
*/
......@@ -822,7 +691,6 @@ static const struct hda_verb alc260_test_init_verbs[] = {
static const char * const alc260_models[ALC260_MODEL_LAST] = {
[ALC260_BASIC] = "basic",
[ALC260_FUJITSU_S702X] = "fujitsu",
[ALC260_ACER] = "acer",
[ALC260_REPLACER_672V] = "replacer",
[ALC260_FAVORIT100] = "favorit100",
#ifdef CONFIG_SND_DEBUG
......@@ -832,8 +700,6 @@ static const char * const alc260_models[ALC260_MODEL_LAST] = {
};
static const struct snd_pci_quirk alc260_cfg_tbl[] = {
SND_PCI_QUIRK(0x1025, 0x007b, "Acer C20x", ALC260_ACER),
SND_PCI_QUIRK(0x1025, 0x008f, "Acer", ALC260_ACER),
SND_PCI_QUIRK(0x1509, 0x4540, "Favorit 100XS", ALC260_FAVORIT100),
SND_PCI_QUIRK(0x104d, 0x81bb, "Sony VAIO", ALC260_BASIC),
SND_PCI_QUIRK(0x104d, 0x81cc, "Sony VAIO", ALC260_BASIC),
......@@ -869,18 +735,6 @@ static const struct alc_config_preset alc260_presets[] = {
.num_mux_defs = ARRAY_SIZE(alc260_fujitsu_capture_sources),
.input_mux = alc260_fujitsu_capture_sources,
},
[ALC260_ACER] = {
.mixers = { alc260_acer_mixer },
.init_verbs = { alc260_acer_init_verbs },
.num_dacs = ARRAY_SIZE(alc260_dac_nids),
.dac_nids = alc260_dac_nids,
.num_adc_nids = ARRAY_SIZE(alc260_dual_adc_nids),
.adc_nids = alc260_dual_adc_nids,
.num_channel_mode = ARRAY_SIZE(alc260_modes),
.channel_mode = alc260_modes,
.num_mux_defs = ARRAY_SIZE(alc260_acer_capture_sources),
.input_mux = alc260_acer_capture_sources,
},
[ALC260_FAVORIT100] = {
.mixers = { alc260_favorit100_mixer },
.init_verbs = { alc260_favorit100_init_verbs },
......
......@@ -4210,6 +4210,7 @@ enum {
ALC260_FIXUP_HP_DC5750,
ALC260_FIXUP_HP_PIN_0F,
ALC260_FIXUP_COEF,
ALC260_FIXUP_GPIO1,
};
static const struct alc_fixup alc260_fixups[] = {
......@@ -4237,10 +4238,16 @@ static const struct alc_fixup alc260_fixups[] = {
.chained = true,
.chain_id = ALC260_FIXUP_HP_PIN_0F,
},
[ALC260_FIXUP_GPIO1] = {
.type = ALC_FIXUP_VERBS,
.v.verbs = alc_gpio1_init_verbs,
},
};
static const struct snd_pci_quirk alc260_fixup_tbl[] = {
SND_PCI_QUIRK(0x1025, 0x007b, "Acer C20x", ALC260_FIXUP_GPIO1),
SND_PCI_QUIRK(0x1025, 0x007f, "Acer Aspire 9500", ALC260_FIXUP_COEF),
SND_PCI_QUIRK(0x1025, 0x008f, "Acer", ALC260_FIXUP_GPIO1),
SND_PCI_QUIRK(0x103c, 0x280a, "HP dc5750", ALC260_FIXUP_HP_DC5750),
SND_PCI_QUIRK(0x1631, 0xc017, "PB V7900", ALC260_FIXUP_COEF),
{}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册