Merge branch 'brcm-pseudo-phy-addr'

Florian Fainelli says:

====================
net: phy: broadcom: define pseudo-PHY address

This patch series converts existing in-tree users of the Broadcom pseudo-PHY
address (30) used to configure MDIO-connected switches to share a constant in a
shared header files.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/dsa/bcm_sf2.c

@@ -24,6 +24,7 @@
 #include <net/dsa.h>
 #include <linux/ethtool.h>
 #include <linux/if_bridge.h>
+#include <linux/brcmphy.h>
 
 #include "bcm_sf2.h"
 #include "bcm_sf2_regs.h"
@@ -697,7 +698,7 @@ static int bcm_sf2_sw_setup(struct dsa_switch *ds)
 	/* Include the pseudo-PHY address and the broadcast PHY address to
 	 * divert reads towards our workaround
 	 */
-	ds->phys_mii_mask |= ((1 << 30) | (1 << 0));
+	ds->phys_mii_mask |= ((1 << BRCM_PSEUDO_PHY_ADDR) | (1 << 0));
 
 	rev = reg_readl(priv, REG_SWITCH_REVISION);
 	priv->hw_params.top_rev = (rev >> SWITCH_TOP_REV_SHIFT) &
@@ -782,7 +783,7 @@ static int bcm_sf2_sw_phy_read(struct dsa_switch *ds, int addr, int regnum)
 	 */
 	switch (addr) {
 	case 0:
-	case 30:
+	case BRCM_PSEUDO_PHY_ADDR:
 		return bcm_sf2_sw_indir_rw(ds, 1, addr, regnum, 0);
 	default:
 		return 0xffff;
@@ -797,7 +798,7 @@ static int bcm_sf2_sw_phy_write(struct dsa_switch *ds, int addr, int regnum,
 	 */
 	switch (addr) {
 	case 0:
-	case 30:
+	case BRCM_PSEUDO_PHY_ADDR:
 		bcm_sf2_sw_indir_rw(ds, 0, addr, regnum, val);
 		break;
 	}

drivers/net/ethernet/broadcom/b44.h

 #ifndef _B44_H
 #define _B44_H
 
+#include <linux/brcmphy.h>
+
 /* Register layout. (These correspond to struct _bcmenettregs in bcm4400.) */
 #define	B44_DEVCTRL	0x0000UL /* Device Control */
 #define  DEVCTRL_MPM		0x00000040 /* Magic Packet PME Enable (B0 only) */
@@ -281,8 +283,10 @@ struct ring_info {
 };
 
 #define B44_MCAST_TABLE_SIZE		32
-#define B44_PHY_ADDR_NO_LOCAL_PHY	30 /* no local phy regs */
-#define B44_PHY_ADDR_NO_PHY		31 /* no phy present at all */
+/* no local phy regs, e.g: Broadcom switches pseudo-PHY */
+#define B44_PHY_ADDR_NO_LOCAL_PHY	BRCM_PSEUDO_PHY_ADDR
+/* no phy present at all */
+#define B44_PHY_ADDR_NO_PHY		31
 #define B44_MDC_RATIO			5000000
 
 #define	B44_STAT_REG_DECLARE		\

drivers/net/ethernet/broadcom/bgmac.h

@@ -13,6 +13,7 @@
 	dev_dbg(&(bgmac)->core->dev, fmt, ##__VA_ARGS__)
 
 #include <linux/bcma/bcma.h>
+#include <linux/brcmphy.h>
 #include <linux/netdevice.h>
 
 #define BGMAC_DEV_CTL				0x000
@@ -349,7 +350,7 @@
 #define BGMAC_DESC_CTL0_SOF			0x80000000	/* Start of frame */
 #define BGMAC_DESC_CTL1_LEN			0x00001FFF
 
-#define BGMAC_PHY_NOREGS			0x1E
+#define BGMAC_PHY_NOREGS			BRCM_PSEUDO_PHY_ADDR
 #define BGMAC_PHY_MASK				0x1F
 
 #define BGMAC_MAX_TX_RINGS			4

include/linux/brcmphy.h

 #ifndef _LINUX_BRCMPHY_H
 #define _LINUX_BRCMPHY_H
 
+#include <linux/phy.h>
+
+/* All Broadcom Ethernet switches have a pseudo-PHY at address 30 which is used
+ * to configure the switch internal registers via MDIO accesses.
+ */
+#define BRCM_PSEUDO_PHY_ADDR           30
+
 #define PHY_ID_BCM50610			0x0143bd60
 #define PHY_ID_BCM50610M		0x0143bd70
 #define PHY_ID_BCM5241			0x0143bc30