Blackfin arch: add support for the BlackStamp board

Signed-off-by: NBenjamin Matthews <bmat@lle.rochester.edu>
Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

arch/blackfin/Kconfig

@@ -249,7 +249,7 @@ config MEM_MT48LC8M32B2B5_7
 
 config MEM_MT48LC32M16A2TG_75
 	bool
-	depends on (BFIN527_EZKIT || BFIN532_IP0X)
+	depends on (BFIN527_EZKIT || BFIN532_IP0X || BLACKSTAMP)
 	default y
 
 source "arch/blackfin/mach-bf527/Kconfig"
@@ -292,7 +292,7 @@ config CLKIN_HZ
 	int "Frequency of the crystal on the board in Hz"
 	default "11059200" if BFIN533_STAMP
 	default "27000000" if BFIN533_EZKIT
-	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS)
+	default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT || H8606_HVSISTEMAS || BLACKSTAMP)
 	default "30000000" if BFIN561_EZKIT
 	default "24576000" if PNAV10
 	default "10000000" if BFIN532_IP0X
@@ -332,7 +332,7 @@ config VCO_MULT
 	default "22" if BFIN533_BLUETECHNIX_CM
 	default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
 	default "20" if BFIN561_EZKIT
-	default "16" if H8606_HVSISTEMAS
+	default "16" if (H8606_HVSISTEMAS || BLACKSTAMP)
 	help
 	  This controls the frequency of the on-chip PLL. This can be between 1 and 64.
 	  PLL Frequency = (Crystal Frequency) * (this setting)

arch/blackfin/mach-bf533/boards/Kconfig

@@ -14,6 +14,12 @@ config BFIN533_STAMP
 	help
 	  BF533-STAMP board support.
 
+config BLACKSTAMP
+	bool "BlackStamp"
+	help
+	  Support for the BlackStamp board.  Hardware info available at
+	  http://blackfin.uclinux.org/gf/project/blackstamp/
+
 config BFIN533_BLUETECHNIX_CM
 	bool "Bluetechnix CM-BF533"
 	depends on (BF533)

arch/blackfin/mach-bf533/boards/Makefile

@@ -7,4 +7,5 @@ obj-$(CONFIG_BFIN533_STAMP)            += stamp.o
 obj-$(CONFIG_BFIN532_IP0X)             += ip0x.o
 obj-$(CONFIG_BFIN533_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN533_BLUETECHNIX_CM)   += cm_bf533.o
+obj-$(CONFIG_BLACKSTAMP)               += blackstamp.o
 obj-$(CONFIG_H8606_HVSISTEMAS)         += H8606.o

arch/blackfin/mach-bf533/boards/blackstamp.c

+/*
+ * File:         arch/blackfin/mach-bf533/blackstamp.c
+ * Based on:     arch/blackfin/mach-bf533/stamp.c
+ * Author:       Benjamin Matthews <bmat@lle.rochester.edu>
+ *               Aidan Williams <aidan@nicta.com.au>
+ *
+ * Created:      2008
+ * Description:  Board Info File for the BlackStamp
+ *
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * More info about the BlackStamp at:
+ * 	http://blackfin.uclinux.org/gf/project/blackstamp/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/irq.h>
+#include <linux/i2c.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "BlackStamp";
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+	.name = "rtc-bfin",
+	.id   = -1,
+};
+#endif
+
+/*
+ *  Driver needs to know address, irq and flag pin.
+ */
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+static struct resource smc91x_resources[] = {
+	{
+		.name = "smc91x-regs",
+		.start = 0x20300300,
+		.end = 0x20300300 + 16,
+		.flags = IORESOURCE_MEM,
+	}, {
+		.start = IRQ_PF3,
+		.end = IRQ_PF3,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device smc91x_device = {
+	.name = "smc91x",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(smc91x_resources),
+	.resource = smc91x_resources,
+};
+#endif
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+	{
+		.name = "bootloader(spi)",
+		.size = 0x00040000,
+		.offset = 0,
+		.mask_flags = MTD_CAP_ROM
+	}, {
+		.name = "linux kernel(spi)",
+		.size = 0x180000,
+		.offset = MTDPART_OFS_APPEND,
+	}, {
+		.name = "file system(spi)",
+		.size = MTDPART_SIZ_FULL,
+		.offset = MTDPART_OFS_APPEND,
+	}
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+	.name = "m25p80",
+	.parts = bfin_spi_flash_partitions,
+	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+	.type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+	.enable_dma = 0,         /* use dma transfer with this chip*/
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+	.enable_dma = 1,
+	.bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+static struct bfin5xx_spi_chip spidev_chip_info = {
+	.enable_dma = 0,
+	.bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+	{
+		/* the modalias must be the same as spi device driver name */
+		.modalias = "m25p80", /* Name of spi_driver for this device */
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0, /* Framework bus number */
+		.chip_select = 2, /* Framework chip select. */
+		.platform_data = &bfin_spi_flash_data,
+		.controller_data = &spi_flash_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+	{
+		.modalias = "spi_mmc_dummy",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 0,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+	{
+		.modalias = "spi_mmc",
+		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = CONFIG_SPI_MMC_CS_CHAN,
+		.platform_data = NULL,
+		.controller_data = &spi_mmc_chip_info,
+		.mode = SPI_MODE_3,
+	},
+#endif
+
+#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
+	{
+		.modalias = "spidev",
+		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
+		.bus_num = 0,
+		.chip_select = 7,
+		.controller_data = &spidev_chip_info,
+	},
+#endif
+};
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+	[0] = {
+		.start = SPI0_REGBASE,
+		.end   = SPI0_REGBASE + 0xFF,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = CH_SPI,
+		.end   = CH_SPI,
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+	.num_chipselect = 8,
+	.enable_dma = 1,  /* master has the ability to do dma transfer */
+	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bfin_spi0_device = {
+	.name = "bfin-spi",
+	.id = 0, /* Bus number */
+	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
+	.resource = bfin_spi0_resource,
+	.dev = {
+		.platform_data = &bfin_spi0_info, /* Passed to driver */
+	},
+};
+#endif  /* spi master and devices */
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bfin_uart_device = {
+	.name = "bfin-uart",
+	.id = 1,
+	.num_resources = ARRAY_SIZE(bfin_uart_resources),
+	.resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+static struct resource bfin_sir_resources[] = {
+#ifdef CONFIG_BFIN_SIR0
+	{
+		.start = 0xFFC00400,
+		.end = 0xFFC004FF,
+		.flags = IORESOURCE_MEM,
+	},
+#endif
+};
+
+static struct platform_device bfin_sir_device = {
+	.name = "bfin_sir",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(bfin_sir_resources),
+	.resource = bfin_sir_resources,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+	.name = "bfin-sport-uart",
+	.id = 1,
+};
+#endif
+
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+
+static struct gpio_keys_button bfin_gpio_keys_table[] = {
+	{BTN_0, GPIO_PF4, 0, "gpio-keys: BTN0"},
+	{BTN_1, GPIO_PF5, 0, "gpio-keys: BTN1"},
+	{BTN_2, GPIO_PF6, 0, "gpio-keys: BTN2"},
+}; /* Mapped to the first three PF Test Points */
+
+static struct gpio_keys_platform_data bfin_gpio_keys_data = {
+	.buttons        = bfin_gpio_keys_table,
+	.nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
+};
+
+static struct platform_device bfin_device_gpiokeys = {
+	.name      = "gpio-keys",
+	.dev = {
+		.platform_data = &bfin_gpio_keys_data,
+	},
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+	.start = 0,
+	.end   = MAX_BLACKFIN_GPIOS - 1,
+	.flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+	.name = "simple-gpio",
+	.id = -1,
+	.num_resources = 1,
+	.resource = &bfin_gpios_resources,
+};
+
+#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+#include <linux/i2c-gpio.h>
+
+static struct i2c_gpio_platform_data i2c_gpio_data = {
+	.sda_pin		= 8,
+	.scl_pin		= 9,
+	.sda_is_open_drain	= 0,
+	.scl_is_open_drain	= 0,
+	.udelay			= 40,
+}; /* This hasn't actually been used these pins
+    * are (currently) free pins on the expansion connector */
+
+static struct platform_device i2c_gpio_device = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &i2c_gpio_data,
+	},
+};
+#endif
+
+#ifdef CONFIG_I2C_BOARDINFO
+static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+	VRPAIR(VLEV_085, 250000000),
+	VRPAIR(VLEV_090, 376000000),
+	VRPAIR(VLEV_095, 426000000),
+	VRPAIR(VLEV_100, 426000000),
+	VRPAIR(VLEV_105, 476000000),
+	VRPAIR(VLEV_110, 476000000),
+	VRPAIR(VLEV_115, 476000000),
+	VRPAIR(VLEV_120, 600000000),
+	VRPAIR(VLEV_125, 600000000),
+	VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+	.tuple_tab = cclk_vlev_datasheet,
+	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+	.vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+	.name = "bfin dpmc",
+	.dev = {
+		.platform_data = &bfin_dmpc_vreg_data,
+	},
+};
+
+static struct platform_device *stamp_devices[] __initdata = {
+
+	&bfin_dpmc,
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+	&rtc_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	&smc91x_device,
+#endif
+
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+	&bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+	&bfin_uart_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+	&bfin_sir_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+	&bfin_sport0_uart_device,
+	&bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
+	&bfin_device_gpiokeys,
+#endif
+
+#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+	&i2c_gpio_device,
+#endif
+
+	&bfin_gpios_device,
+};
+
+static int __init blackstamp_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "%s(): registering device resources\n", __func__);
+
+#ifdef CONFIG_I2C_BOARDINFO
+	i2c_register_board_info(0, bfin_i2c_board_info,
+				ARRAY_SIZE(bfin_i2c_board_info));
+#endif
+
+	ret = platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
+	if (ret < 0)
+		return ret;
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+	/* setup BF533_STAMP CPLD to route AMS3 to Ethernet MAC */
+	bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF0);
+	bfin_write_FIO_FLAG_S(PF0);
+	SSYNC();
+#endif
+
+	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+	return 0;
+}
+
+arch_initcall(blackstamp_init);