serial: 8250_pci: Replace dev_*() by pci_*() macros

PCI subsystem provides convenient shortcut macros for message printing.
Use those macros instead of dev_*().
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NJiri Slaby <jslaby@kernel.org>
Link: https://lore.kernel.org/r/20211022135147.70965-3-andriy.shevchenko@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/8250/8250_pci.c

@@ -75,13 +75,12 @@ static int pci_default_setup(struct serial_private*,
 
 static void moan_device(const char *str, struct pci_dev *dev)
 {
-	dev_err(&dev->dev,
-	       "%s: %s\n"
+	pci_err(dev, "%s\n"
 	       "Please send the output of lspci -vv, this\n"
 	       "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n"
 	       "manufacturer and name of serial board or\n"
 	       "modem board to <linux-serial@vger.kernel.org>.\n",
-	       pci_name(dev), str, dev->vendor, dev->device,
+	       str, dev->vendor, dev->device,
 	       dev->subsystem_vendor, dev->subsystem_device);
 }
 
@@ -238,7 +237,7 @@ static int pci_inteli960ni_init(struct pci_dev *dev)
 	/* is firmware started? */
 	pci_read_config_dword(dev, 0x44, &oldval);
 	if (oldval == 0x00001000L) { /* RESET value */
-		dev_dbg(&dev->dev, "Local i960 firmware missing\n");
+		pci_dbg(dev, "Local i960 firmware missing\n");
 		return -ENODEV;
 	}
 	return 0;
@@ -588,9 +587,8 @@ static int pci_timedia_probe(struct pci_dev *dev)
 	 * (0,2,3,5,6: serial only -- 7,8,9: serial + parallel)
 	 */
 	if ((dev->subsystem_device & 0x00f0) >= 0x70) {
-		dev_info(&dev->dev,
-			"ignoring Timedia subdevice %04x for parport_serial\n",
-			dev->subsystem_device);
+		pci_info(dev, "ignoring Timedia subdevice %04x for parport_serial\n",
+			 dev->subsystem_device);
 		return -ENODEV;
 	}
 
@@ -827,8 +825,7 @@ static int pci_netmos_9900_numports(struct pci_dev *dev)
 		if (sub_serports > 0)
 			return sub_serports;
 
-		dev_err(&dev->dev,
-			"NetMos/Mostech serial driver ignoring port on ambiguous config.\n");
+		pci_err(dev, "NetMos/Mostech serial driver ignoring port on ambiguous config.\n");
 		return 0;
 	}
 
@@ -927,7 +924,7 @@ static int pci_ite887x_init(struct pci_dev *dev)
 	}
 
 	if (i == ARRAY_SIZE(inta_addr)) {
-		dev_err(&dev->dev, "ite887x: could not find iobase\n");
+		pci_err(dev, "could not find iobase\n");
 		return -ENODEV;
 	}
 
@@ -1022,9 +1019,7 @@ static int pci_endrun_init(struct pci_dev *dev)
 	/* EndRun device */
 	if (deviceID == 0x07000200) {
 		number_uarts = ioread8(p + 4);
-		dev_dbg(&dev->dev,
-			"%d ports detected on EndRun PCI Express device\n",
-			number_uarts);
+		pci_dbg(dev, "%d ports detected on EndRun PCI Express device\n", number_uarts);
 	}
 	pci_iounmap(dev, p);
 	return number_uarts;
@@ -1054,9 +1049,7 @@ static int pci_oxsemi_tornado_init(struct pci_dev *dev)
 	/* Tornado device */
 	if (deviceID == 0x07000200) {
 		number_uarts = ioread8(p + 4);
-		dev_dbg(&dev->dev,
-			"%d ports detected on Oxford PCI Express device\n",
-			number_uarts);
+		pci_dbg(dev, "%d ports detected on Oxford PCI Express device\n", number_uarts);
 	}
 	pci_iounmap(dev, p);
 	return number_uarts;
@@ -1116,15 +1109,15 @@ static struct quatech_feature quatech_cards[] = {
 	{ 0, }
 };
 
-static int pci_quatech_amcc(u16 devid)
+static int pci_quatech_amcc(struct pci_dev *dev)
 {
 	struct quatech_feature *qf = &quatech_cards[0];
 	while (qf->devid) {
-		if (qf->devid == devid)
+		if (qf->devid == dev->device)
 			return qf->amcc;
 		qf++;
 	}
-	pr_err("quatech: unknown port type '0x%04X'.\n", devid);
+	pci_err(dev, "unknown port type '0x%04X'.\n", dev->device);
 	return 0;
 };
 
@@ -1287,7 +1280,7 @@ static int pci_quatech_rs422(struct uart_8250_port *port)
 
 static int pci_quatech_init(struct pci_dev *dev)
 {
-	if (pci_quatech_amcc(dev->device)) {
+	if (pci_quatech_amcc(dev)) {
 		unsigned long base = pci_resource_start(dev, 0);
 		if (base) {
 			u32 tmp;
@@ -1311,7 +1304,7 @@ static int pci_quatech_setup(struct serial_private *priv,
 	port->port.uartclk = pci_quatech_clock(port);
 	/* For now just warn about RS422 */
 	if (pci_quatech_rs422(port))
-		pr_warn("quatech: software control of RS422 features not currently supported.\n");
+		pci_warn(priv->dev, "software control of RS422 features not currently supported.\n");
 	return pci_default_setup(priv, board, port, idx);
 }
 
@@ -1521,7 +1514,7 @@ static int pci_fintek_setup(struct serial_private *priv,
 	/* Get the io address from configuration space */
 	pci_read_config_word(pdev, config_base + 4, &iobase);
 
-	dev_dbg(&pdev->dev, "%s: idx=%d iobase=0x%x", __func__, idx, iobase);
+	pci_dbg(pdev, "idx=%d iobase=0x%x", idx, iobase);
 
 	port->port.iotype = UPIO_PORT;
 	port->port.iobase = iobase;
@@ -1685,7 +1678,7 @@ static int skip_tx_en_setup(struct serial_private *priv,
 			struct uart_8250_port *port, int idx)
 {
 	port->port.quirks |= UPQ_NO_TXEN_TEST;
-	dev_dbg(&priv->dev->dev,
+	pci_dbg(priv->dev,
 		"serial8250: skipping TxEn test for device [%04x:%04x] subsystem [%04x:%04x]\n",
 		priv->dev->vendor, priv->dev->device,
 		priv->dev->subsystem_vendor, priv->dev->subsystem_device);
@@ -3994,12 +3987,12 @@ pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board)
 		uart.port.irq = 0;
 	} else {
 		if (pci_match_id(pci_use_msi, dev)) {
-			dev_dbg(&dev->dev, "Using MSI(-X) interrupts\n");
+			pci_dbg(dev, "Using MSI(-X) interrupts\n");
 			pci_set_master(dev);
 			uart.port.flags &= ~UPF_SHARE_IRQ;
 			rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES);
 		} else {
-			dev_dbg(&dev->dev, "Using legacy interrupts\n");
+			pci_dbg(dev, "Using legacy interrupts\n");
 			rc = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_LEGACY);
 		}
 		if (rc < 0) {
@@ -4017,12 +4010,12 @@ pciserial_init_ports(struct pci_dev *dev, const struct pciserial_board *board)
 		if (quirk->setup(priv, board, &uart, i))
 			break;
 
-		dev_dbg(&dev->dev, "Setup PCI port: port %lx, irq %d, type %d\n",
+		pci_dbg(dev, "Setup PCI port: port %lx, irq %d, type %d\n",
 			uart.port.iobase, uart.port.irq, uart.port.iotype);
 
 		priv->line[i] = serial8250_register_8250_port(&uart);
 		if (priv->line[i] < 0) {
-			dev_err(&dev->dev,
+			pci_err(dev,
 				"Couldn't register serial port %lx, irq %d, type %d, error %d\n",
 				uart.port.iobase, uart.port.irq,
 				uart.port.iotype, priv->line[i]);
@@ -4118,8 +4111,7 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
 	}
 
 	if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
-		dev_err(&dev->dev, "invalid driver_data: %ld\n",
-			ent->driver_data);
+		pci_err(dev, "invalid driver_data: %ld\n", ent->driver_data);
 		return -EINVAL;
 	}
 
@@ -4202,7 +4194,7 @@ static int pciserial_resume_one(struct device *dev)
 		err = pci_enable_device(pdev);
 		/* FIXME: We cannot simply error out here */
 		if (err)
-			dev_err(dev, "Unable to re-enable ports, trying to continue.\n");
+			pci_err(pdev, "Unable to re-enable ports, trying to continue.\n");
 		pciserial_resume_ports(priv);
 	}
 	return 0;