提交 0cf736a1 编写于 作者: V Vikas Gupta 提交者: Jakub Kicinski

bnxt_en: fix the handling of PCIE-AER

Fix the sequence required for PCIE-AER. While slot reset occurs, firmware
might not be ready and the driver needs to check for its recovery.  We
also need to remap the health registers for some chips and clear the
resource reservations.  The resources will be allocated again during
bnxt_io_resume().

Fixes: fb1e6e56 ("bnxt_en: Fix AER recovery.")
Signed-off-by: NVikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
上级 b4c66425
......@@ -13922,7 +13922,9 @@ static pci_ers_result_t bnxt_io_slot_reset(struct pci_dev *pdev)
pci_ers_result_t result = PCI_ERS_RESULT_DISCONNECT;
struct net_device *netdev = pci_get_drvdata(pdev);
struct bnxt *bp = netdev_priv(netdev);
int err = 0, off;
int retry = 0;
int err = 0;
int off;
netdev_info(bp->dev, "PCI Slot Reset\n");
......@@ -13950,11 +13952,36 @@ static pci_ers_result_t bnxt_io_slot_reset(struct pci_dev *pdev)
pci_restore_state(pdev);
pci_save_state(pdev);
bnxt_inv_fw_health_reg(bp);
bnxt_try_map_fw_health_reg(bp);
/* In some PCIe AER scenarios, firmware may take up to
* 10 seconds to become ready in the worst case.
*/
do {
err = bnxt_try_recover_fw(bp);
if (!err)
break;
retry++;
} while (retry < BNXT_FW_SLOT_RESET_RETRY);
if (err) {
dev_err(&pdev->dev, "Firmware not ready\n");
goto reset_exit;
}
err = bnxt_hwrm_func_reset(bp);
if (!err)
result = PCI_ERS_RESULT_RECOVERED;
bnxt_ulp_irq_stop(bp);
bnxt_clear_int_mode(bp);
err = bnxt_init_int_mode(bp);
bnxt_ulp_irq_restart(bp, err);
}
reset_exit:
bnxt_clear_reservations(bp, true);
rtnl_unlock();
return result;
......
......@@ -1621,6 +1621,7 @@ struct bnxt_fw_health {
#define BNXT_FW_RETRY 5
#define BNXT_FW_IF_RETRY 10
#define BNXT_FW_SLOT_RESET_RETRY 4
enum board_idx {
BCM57301,
......
......@@ -476,7 +476,8 @@ static int __hwrm_send(struct bnxt *bp, struct bnxt_hwrm_ctx *ctx)
memset(ctx->resp, 0, PAGE_SIZE);
req_type = le16_to_cpu(ctx->req->req_type);
if (BNXT_NO_FW_ACCESS(bp) && req_type != HWRM_FUNC_RESET) {
if (BNXT_NO_FW_ACCESS(bp) &&
(req_type != HWRM_FUNC_RESET && req_type != HWRM_VER_GET)) {
netdev_dbg(bp->dev, "hwrm req_type 0x%x skipped, FW channel down\n",
req_type);
goto exit;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册