提交 02ed21ae 编写于 作者: M Michael Neuling 提交者: Michael Ellerman

powerpc/powernv: Define and set POWER9 HFSCR doorbell bit

Define and set the POWER9 HFSCR doorbell bit so that guests can use
msgsndp.

ISA 3.0 calls this MSGP, so name it accordingly in the code.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
上级 1f0f2e72
...@@ -309,6 +309,7 @@ ...@@ -309,6 +309,7 @@
/* HFSCR and FSCR bit numbers are the same */ /* HFSCR and FSCR bit numbers are the same */
#define FSCR_LM_LG 11 /* Enable Load Monitor Registers */ #define FSCR_LM_LG 11 /* Enable Load Monitor Registers */
#define FSCR_MSGP_LG 10 /* Enable MSGP */
#define FSCR_TAR_LG 8 /* Enable Target Address Register */ #define FSCR_TAR_LG 8 /* Enable Target Address Register */
#define FSCR_EBB_LG 7 /* Enable Event Based Branching */ #define FSCR_EBB_LG 7 /* Enable Event Based Branching */
#define FSCR_TM_LG 5 /* Enable Transactional Memory */ #define FSCR_TM_LG 5 /* Enable Transactional Memory */
...@@ -324,6 +325,7 @@ ...@@ -324,6 +325,7 @@
#define FSCR_DSCR __MASK(FSCR_DSCR_LG) #define FSCR_DSCR __MASK(FSCR_DSCR_LG)
#define SPRN_HFSCR 0xbe /* HV=1 Facility Status & Control Register */ #define SPRN_HFSCR 0xbe /* HV=1 Facility Status & Control Register */
#define HFSCR_LM __MASK(FSCR_LM_LG) #define HFSCR_LM __MASK(FSCR_LM_LG)
#define HFSCR_MSGP __MASK(FSCR_MSGP_LG)
#define HFSCR_TAR __MASK(FSCR_TAR_LG) #define HFSCR_TAR __MASK(FSCR_TAR_LG)
#define HFSCR_EBB __MASK(FSCR_EBB_LG) #define HFSCR_EBB __MASK(FSCR_EBB_LG)
#define HFSCR_TM __MASK(FSCR_TM_LG) #define HFSCR_TM __MASK(FSCR_TM_LG)
......
...@@ -174,7 +174,7 @@ __init_FSCR: ...@@ -174,7 +174,7 @@ __init_FSCR:
__init_HFSCR: __init_HFSCR:
mfspr r3,SPRN_HFSCR mfspr r3,SPRN_HFSCR
ori r3,r3,HFSCR_TAR|HFSCR_TM|HFSCR_BHRB|HFSCR_PM|\ ori r3,r3,HFSCR_TAR|HFSCR_TM|HFSCR_BHRB|HFSCR_PM|\
HFSCR_DSCR|HFSCR_VECVSX|HFSCR_FP|HFSCR_EBB HFSCR_DSCR|HFSCR_VECVSX|HFSCR_FP|HFSCR_EBB|HFSCR_MSGP
mtspr SPRN_HFSCR,r3 mtspr SPRN_HFSCR,r3
blr blr
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册