Kconfig 16.2 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4
config MMU
	bool
	default y

5 6 7 8
config ZONE_DMA
	bool
	default y

L
Linus Torvalds 已提交
9 10 11 12 13 14 15
config RWSEM_GENERIC_SPINLOCK
	bool
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool

16 17 18
config GENERIC_CMOS_UPDATE
	def_bool y

19
config ARCH_USES_GETTIMEOFFSET
J
Jesper Nilsson 已提交
20
	def_bool n
21

22 23 24 25
config GENERIC_IOMAP
       bool
       default y

26 27 28 29 30 31 32 33
config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

34 35 36 37
config GENERIC_HWEIGHT
	bool
	default y

L
Linus Torvalds 已提交
38 39 40 41
config GENERIC_CALIBRATE_DELAY
	bool
	default y

A
Al Viro 已提交
42 43 44
config NO_IOPORT
	def_bool y

45 46 47 48
config FORCE_MAX_ZONEORDER
	int
	default 6

L
Linus Torvalds 已提交
49 50 51
config CRIS
	bool
	default y
S
Sam Ravnborg 已提交
52
	select HAVE_IDE
T
Thomas Gleixner 已提交
53
	select HAVE_GENERIC_HARDIRQS
54
	select GENERIC_IRQ_SHOW
L
Linus Torvalds 已提交
55

56 57 58 59
config HZ
	int
	default 100

L
Linus Torvalds 已提交
60 61
source "init/Kconfig"

62 63
source "kernel/Kconfig.freezer"

L
Linus Torvalds 已提交
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
menu "General setup"

source "fs/Kconfig.binfmt"

config ETRAX_CMDLINE
	string "Kernel command line"
	default "root=/dev/mtdblock3"
	help
	  Pass additional commands to the kernel.

config ETRAX_WATCHDOG
	bool "Enable ETRAX watchdog"
	help
	  Enable the built-in watchdog timer support on ETRAX based embedded
	  network computers.

config ETRAX_WATCHDOG_NICE_DOGGY
	bool "Disable watchdog during Oops printouts"
	depends on ETRAX_WATCHDOG
	help
	  By enabling this you make sure that the watchdog does not bite while
	  printing oopses. Recommended for development systems but not for
	  production releases.

config ETRAX_FAST_TIMER
       bool "Enable ETRAX fast timer API"
       help
         This options enables the API to a fast timer implementation using
	 timer1 to get sub jiffie resolution timers (primarily one-shot
	 timers).
	 This is needed if CONFIG_ETRAX_SERIAL_FAST_TIMER is enabled.

96 97
config ETRAX_KMALLOCED_MODULES
	bool "Enable module allocation with kmalloc"
L
Linus Torvalds 已提交
98
	help
99 100 101 102
	  Enable module allocation with kmalloc instead of vmalloc.

config OOM_REBOOT
       bool "Enable reboot at out of memory"
L
Linus Torvalds 已提交
103

104
source "kernel/Kconfig.preempt"
L
Linus Torvalds 已提交
105

106 107
source mm/Kconfig

L
Linus Torvalds 已提交
108 109 110 111 112 113 114 115 116 117
endmenu

menu "Hardware setup"

choice
	prompt "Processor type"
	default ETRAX100LX

config ETRAX100LX
	bool "ETRAX-100LX-v1"
J
Jesper Nilsson 已提交
118
	select ARCH_USES_GETTIMEOFFSET
L
Linus Torvalds 已提交
119 120 121 122 123
	help
	  Support version 1 of the ETRAX 100LX.

config ETRAX100LX_V2
	bool "ETRAX-100LX-v2"
J
Jesper Nilsson 已提交
124
	select ARCH_USES_GETTIMEOFFSET
L
Linus Torvalds 已提交
125 126 127 128 129
	help
	  Support version 2 of the ETRAX 100LX.

config SVINTO_SIM
	bool "ETRAX-100LX-for-xsim-simulator"
J
Jesper Nilsson 已提交
130
	select ARCH_USES_GETTIMEOFFSET
L
Linus Torvalds 已提交
131 132 133
	help
	  Support the xsim ETRAX Simulator.

134 135 136 137 138 139 140 141 142 143
config ETRAXFS
	bool "ETRAX-FS-V32"
	help
	  Support CRIS V32.

config CRIS_MACH_ARTPEC3
        bool "ARTPEC-3"
        help
          Support Axis ARTPEC-3.

L
Linus Torvalds 已提交
144 145
endchoice

146 147 148 149 150
config ETRAX_VCS_SIM
	bool "VCS Simulator"
	help
	  Setup hardware to be run in the VCS simulator.

L
Linus Torvalds 已提交
151 152 153 154 155
config ETRAX_ARCH_V10
       bool
       default y if ETRAX100LX || ETRAX100LX_V2
       default n if !(ETRAX100LX || ETRAX100LX_V2)

156 157 158 159 160
config ETRAX_ARCH_V32
       bool
       default y if (ETRAXFS || CRIS_MACH_ARTPEC3)
       default n if !(ETRAXFS || CRIS_MACH_ARTPEC3)

L
Linus Torvalds 已提交
161 162 163 164 165 166
config ETRAX_DRAM_SIZE
	int "DRAM size (dec, in MB)"
	default "8"
	help
	  Size of DRAM (decimal in MB) typically 2, 8 or 16.

167 168 169 170 171 172 173
config ETRAX_VMEM_SIZE
       int "Video memory size (dec, in MB)"
       depends on ETRAX_ARCH_V32 && !ETRAXFS
       default 8 if !ETRAXFS
       help
	Size of Video accessible memory (decimal, in MB).

L
Linus Torvalds 已提交
174
config ETRAX_FLASH_BUSWIDTH
175
	int "Buswidth of NOR flash in bytes"
L
Linus Torvalds 已提交
176 177
	default "2"
	help
178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251
	  Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2.

config ETRAX_NANDFLASH_BUSWIDTH
	int "Buswidth of NAND flash in bytes"
	default "1"
	help
	  Width in bytes of the NAND flash (1 or 2).

config ETRAX_FLASH1_SIZE
       int "FLASH1 size (dec, in MB. 0 = Unknown)"
       default "0"

choice
	prompt "Product debug-port"
	default ETRAX_DEBUG_PORT0

config ETRAX_DEBUG_PORT0
	bool "Serial-0"
	help
	  Choose a serial port for the ETRAX debug console.  Default to
	  port 0.

config ETRAX_DEBUG_PORT1
	bool "Serial-1"
	help
	  Use serial port 1 for the console.

config ETRAX_DEBUG_PORT2
	bool "Serial-2"
	help
	  Use serial port 2 for the console.

config ETRAX_DEBUG_PORT3
	bool "Serial-3"
	help
	  Use serial port 3 for the console.

config ETRAX_DEBUG_PORT_NULL
	bool "disabled"
	help
	  Disable serial-port debugging.

endchoice

choice
	prompt "Kernel GDB port"
	depends on ETRAX_KGDB
	default ETRAX_KGDB_PORT0
	help
	  Choose a serial port for kernel debugging.  NOTE: This port should
	  not be enabled under Drivers for built-in interfaces (as it has its
	  own initialization code) and should not be the same as the debug port.

config ETRAX_KGDB_PORT0
	bool "Serial-0"
	help
	  Use serial port 0 for kernel debugging.

config ETRAX_KGDB_PORT1
	bool "Serial-1"
	help
	  Use serial port 1 for kernel debugging.

config ETRAX_KGDB_PORT2
	bool "Serial-2"
	help
	  Use serial port 2 for kernel debugging.

config ETRAX_KGDB_PORT3
	bool "Serial-3"
	help
	  Use serial port 3 for kernel debugging.

endchoice
L
Linus Torvalds 已提交
252 253

source arch/cris/arch-v10/Kconfig
254
source arch/cris/arch-v32/Kconfig
L
Linus Torvalds 已提交
255 256 257

endmenu

258 259
source "net/Kconfig"

L
Linus Torvalds 已提交
260 261
# bring in ETRAX built-in drivers
menu "Drivers for built-in interfaces"
262 263
source arch/cris/arch-v10/drivers/Kconfig
source arch/cris/arch-v32/drivers/Kconfig
L
Linus Torvalds 已提交
264

265 266 267 268 269 270 271 272 273 274 275 276 277
config ETRAX_AXISFLASHMAP
	bool "Axis flash-map support"
	select MTD
	select MTD_CFI
	select MTD_CFI_AMDSTD
	select MTD_JEDECPROBE if ETRAX_ARCH_V32
	select MTD_CHAR
	select MTD_BLOCK
	select MTD_COMPLEX_MAPPINGS
	help
	  This option enables MTD mapping of flash devices.  Needed to use
	  flash memories.  If unsure, say Y.

278 279 280 281 282 283 284 285 286 287 288 289
config ETRAX_RTC
	bool "Real Time Clock support"
	depends on ETRAX_I2C
	help
	  Enables drivers for the Real-Time Clock battery-backed chips on
	  some products. The kernel reads the time when booting, and
	  the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a
	  rtc_time struct (see <file:include/asm-cris/rtc.h>) on the /dev/rtc
	  device.  You can check the time with cat /proc/rtc, but
	  normal time reading should be done using libc function time and
	  friends.

290 291 292
choice
	prompt "RTC chip"
	depends on ETRAX_RTC
293
	default ETRAX_DS1302
294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309

config ETRAX_DS1302
	depends on ETRAX_ARCH_V10
	bool "DS1302"
	help
	  Enables the driver for the DS1302 Real-Time Clock battery-backed
	  chip on some products.

config ETRAX_PCF8563
	bool "PCF8563"
	help
	  Enables the driver for the PCF8563 Real-Time Clock battery-backed
	  chip on some products.

endchoice

310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340
config ETRAX_SYNCHRONOUS_SERIAL
	bool "Synchronous serial-port support"
	help
	  Select this to enable the synchronous serial port driver.

config ETRAX_SYNCHRONOUS_SERIAL_PORT0
	bool "Synchronous serial port 0 enabled"
	depends on ETRAX_SYNCHRONOUS_SERIAL
	help
	  Enabled synchronous serial port 0.

config ETRAX_SYNCHRONOUS_SERIAL0_DMA
	bool "Enable DMA on synchronous serial port 0."
	depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
	help
	  A synchronous serial port can run in manual or DMA mode.
	  Selecting this option will make it run in DMA mode.

config ETRAX_SYNCHRONOUS_SERIAL_PORT1
	bool "Synchronous serial port 1 enabled"
	depends on ETRAX_SYNCHRONOUS_SERIAL && (ETRAXFS || ETRAX_ARCH_V10)
	help
	  Enabled synchronous serial port 1.

config ETRAX_SYNCHRONOUS_SERIAL1_DMA
	bool "Enable DMA on synchronous serial port 1."
	depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
	help
	  A synchronous serial port can run in manual or DMA mode.
	  Selecting this option will make it run in DMA mode.

341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433
choice
	prompt "Network LED behavior"
	depends on ETRAX_ETHERNET
	default ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY

config ETRAX_NETWORK_LED_ON_WHEN_LINK
	bool "LED_on_when_link"
	help
	  Selecting LED_on_when_link will light the LED when there is a
	  connection and will flash off when there is activity.

	  Selecting LED_on_when_activity will light the LED only when
	  there is activity.

	  This setting will also affect the behaviour of other activity LEDs
	  e.g. Bluetooth.

config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
	bool "LED_on_when_activity"
	help
	  Selecting LED_on_when_link will light the LED when there is a
	  connection and will flash off when there is activity.

	  Selecting LED_on_when_activity will light the LED only when
	  there is activity.

	  This setting will also affect the behaviour of other activity LEDs
	  e.g. Bluetooth.

endchoice

choice
	prompt "Ser0 DMA out channel"
	depends on ETRAX_SERIAL_PORT0
	default ETRAX_SERIAL_PORT0_DMA6_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT0_NO_DMA_OUT if ETRAX_ARCH_V10

config ETRAX_SERIAL_PORT0_NO_DMA_OUT
	bool "Ser0 uses no DMA for output"
	help
	  Do not use DMA for ser0 output.

config ETRAX_SERIAL_PORT0_DMA6_OUT
	bool "Ser0 uses DMA6 for output"
	depends on ETRAXFS
	help
	  Enables the DMA6 output channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT0_DMA0_OUT
	bool "Ser0 uses DMA0 for output"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA0 output channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser0 DMA in channel "
	depends on ETRAX_SERIAL_PORT0
	default ETRAX_SERIAL_PORT0_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT0_DMA7_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser0.

config ETRAX_SERIAL_PORT0_NO_DMA_IN
	bool "Ser0 uses no DMA for input"
	help
	  Do not use DMA for ser0 input.

config ETRAX_SERIAL_PORT0_DMA7_IN
	bool "Ser0 uses DMA7 for input"
	depends on ETRAXFS
	help
	  Enables the DMA7 input channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT0_DMA1_IN
	bool "Ser0 uses DMA1 for input"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA1 input channel for ser0 (ttyS0).
	  If you do not enable DMA, an interrupt for each character will be
434
	  used when receiving data.
435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser1 DMA in channel "
	depends on ETRAX_SERIAL_PORT1
	default ETRAX_SERIAL_PORT1_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT1_DMA9_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser1.

config ETRAX_SERIAL_PORT1_NO_DMA_IN
	bool "Ser1 uses no DMA for input"
	help
	  Do not use DMA for ser1 input.

config ETRAX_SERIAL_PORT1_DMA5_IN
	bool "Ser1 uses DMA5 for input"
	depends on ETRAX_ARCH_V32
	help
	  Enables the DMA5 input channel for ser1 (ttyS1).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want this on, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT1_DMA9_IN
	depends on ETRAX_ARCH_V10
	bool "Ser1 uses DMA9 for input"

endchoice


choice
	prompt "Ser1 DMA out channel"
	depends on ETRAX_SERIAL_PORT1
	default ETRAX_SERIAL_PORT1_NO_DMA_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT1_DMA8_OUT if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser1.

config ETRAX_SERIAL_PORT1_NO_DMA_OUT
	bool "Ser1 uses no DMA for output"
	help
	  Do not use DMA for ser1 output.

config ETRAX_SERIAL_PORT1_DMA8_OUT
	depends on ETRAX_ARCH_V10
	bool "Ser1 uses DMA8 for output"

config ETRAX_SERIAL_PORT1_DMA4_OUT
	depends on ETRAX_ARCH_V32
	bool "Ser1 uses DMA4 for output"
	help
	  Enables the DMA4 output channel for ser1 (ttyS1).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want this on, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser2 DMA out channel"
	depends on ETRAX_SERIAL_PORT2
	default ETRAX_SERIAL_PORT2_NO_DMA_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT2_DMA2_OUT if ETRAX_ARCH_V10

config ETRAX_SERIAL_PORT2_NO_DMA_OUT
	bool "Ser2 uses no DMA for output"
	help
	  Do not use DMA for ser2 output.

config ETRAX_SERIAL_PORT2_DMA2_OUT
	bool "Ser2 uses DMA2 for output"
	depends on ETRAXFS || ETRAX_ARCH_V10
	help
	  Enables the DMA2 output channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT2_DMA6_OUT
	bool "Ser2 uses DMA6 for output"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA6 output channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser2 DMA in channel"
	depends on ETRAX_SERIAL_PORT2
	default ETRAX_SERIAL_PORT2_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT2_DMA3_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser2.

config ETRAX_SERIAL_PORT2_NO_DMA_IN
	bool "Ser2 uses no DMA for input"
	help
	  Do not use DMA for ser2 input.

config ETRAX_SERIAL_PORT2_DMA3_IN
	bool "Ser2 uses DMA3 for input"
	depends on ETRAXFS || ETRAX_ARCH_V10
	help
	  Enables the DMA3 input channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT2_DMA7_IN
	bool "Ser2 uses DMA7 for input"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA7 input channel for ser2 (ttyS2).
	  If you do not enable DMA, an interrupt for each character will be
561
	  used when receiving data.
562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser3 DMA in channel"
	depends on ETRAX_SERIAL_PORT3
	default ETRAX_SERIAL_PORT3_NO_DMA_IN if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT3_DMA5_IN if ETRAX_ARCH_V10
	help
	  What DMA channel to use for ser3.

config ETRAX_SERIAL_PORT3_NO_DMA_IN
	bool "Ser3 uses no DMA for input"
	help
	  Do not use DMA for ser3 input.

config ETRAX_SERIAL_PORT3_DMA5_IN
	depends on ETRAX_ARCH_V10
	bool "DMA 5"

config ETRAX_SERIAL_PORT3_DMA9_IN
	bool "Ser3 uses DMA9 for input"
	depends on ETRAXFS
	help
	  Enables the DMA9 input channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when receiving data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT3_DMA3_IN
	bool "Ser3 uses DMA3 for input"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA3 input channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
600
	  used when receiving data.
601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

choice
	prompt "Ser3 DMA out channel"
	depends on ETRAX_SERIAL_PORT3
	default ETRAX_SERIAL_PORT3_NO_DMA_OUT if ETRAX_ARCH_V32
	default ETRAX_SERIAL_PORT3_DMA4_OUT if ETRAX_ARCH_V10

config ETRAX_SERIAL_PORT3_NO_DMA_OUT
	bool "Ser3 uses no DMA for output"
	help
	  Do not use DMA for ser3 output.

config ETRAX_SERIAL_PORT3_DMA4_OUT
	depends on ETRAX_ARCH_V10
	bool "DMA 4"

config ETRAX_SERIAL_PORT3_DMA8_OUT
	bool "Ser3 uses DMA8 for output"
	depends on ETRAXFS
	help
	  Enables the DMA8 output channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

config ETRAX_SERIAL_PORT3_DMA2_OUT
	bool "Ser3 uses DMA2 for output"
	depends on CRIS_MACH_ARTPEC3
	help
	  Enables the DMA2 output channel for ser3 (ttyS3).
	  If you do not enable DMA, an interrupt for each character will be
	  used when transmitting data.
	  Normally you want to use DMA, unless you use the DMA channel for
	  something else.

endchoice

L
Linus Torvalds 已提交
643 644 645 646 647 648 649 650 651 652 653 654 655 656 657
endmenu

source "drivers/base/Kconfig"

# standard linux drivers
source "drivers/mtd/Kconfig"

source "drivers/parport/Kconfig"

source "drivers/pnp/Kconfig"

source "drivers/block/Kconfig"

source "drivers/ide/Kconfig"

658
source "drivers/net/Kconfig"
L
Linus Torvalds 已提交
659

660 661 662 663
source "drivers/i2c/Kconfig"

source "drivers/rtc/Kconfig"

L
Linus Torvalds 已提交
664 665 666 667 668 669 670 671 672 673 674
#
# input before char - char/joystick depends on it. As does USB.
#
source "drivers/input/Kconfig"

source "drivers/char/Kconfig"

source "fs/Kconfig"

source "drivers/usb/Kconfig"

675 676
source "drivers/uwb/Kconfig"

677 678
source "drivers/staging/Kconfig"

L
Linus Torvalds 已提交
679 680 681 682 683 684 685
source "arch/cris/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

source "lib/Kconfig"