Kconfig 20.7 KB
Newer Older
1 2 3 4 5 6 7
config LEDS_GPIO_REGISTER
	bool
	help
	  This option provides the function gpio_led_register_device.
	  As this function is used by arch code it must not be compiled as a
	  module.

8
menuconfig NEW_LEDS
R
Richard Purdie 已提交
9 10
	bool "LED Support"
	help
11 12 13
	  Say Y to enable Linux LED support.  This allows control of supported
	  LEDs from both userspace and optionally, by kernel events (triggers).

14 15
if NEW_LEDS

R
Richard Purdie 已提交
16
config LEDS_CLASS
17
	tristate "LED Class Support"
R
Richard Purdie 已提交
18 19 20 21
	help
	  This option enables the led sysfs class in /sys/class/leds.  You'll
	  need this to do anything useful with LEDs.  If unsure, say N.

22 23 24 25 26 27 28 29 30 31
config LEDS_CLASS_FLASH
	tristate "LED Flash Class Support"
	depends on LEDS_CLASS
	help
	  This option enables the flash led sysfs class in /sys/class/leds.
	  It wrapps LED Class and adds flash LEDs specific sysfs attributes
	  and kernel internal API to it. You'll need this to provide support
	  for the flash related features of a LED device. It can be built
	  as a module.

32 33 34 35 36 37 38 39 40
config LEDS_BRIGHTNESS_HW_CHANGED
	bool "LED Class brightness_hw_changed attribute support"
	depends on LEDS_CLASS
	help
	  This option enables support for the brightness_hw_changed attribute
	  for led sysfs class devices under /sys/class/leds.

	  See Documentation/ABI/testing/sysfs-class-led for details.

B
Ben Dooks 已提交
41
comment "LED drivers"
42

H
Haojian Zhuang 已提交
43 44
config LEDS_88PM860X
	tristate "LED Support for Marvell 88PM860x PMIC"
J
Johannes Berg 已提交
45
	depends on LEDS_CLASS
R
Richard Purdie 已提交
46
	depends on MFD_88PM860X
H
Haojian Zhuang 已提交
47 48 49 50
	help
	  This option enables support for on-chip LED drivers found on Marvell
	  Semiconductor 88PM8606 PMIC.

51 52 53
config LEDS_AAT1290
	tristate "LED support for the AAT1290"
	depends on LEDS_CLASS_FLASH
R
Randy Dunlap 已提交
54
	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
55
	depends on GPIOLIB || COMPILE_TEST
56
	depends on OF
57
	depends on PINCTRL
58 59 60
	help
	 This option enables support for the LEDs on the AAT1290.

61 62 63
config LEDS_BCM6328
	tristate "LED Support for Broadcom BCM6328"
	depends on LEDS_CLASS
64
	depends on HAS_IOMEM
65 66 67 68 69
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6328
	  LED HW controller accessed via MMIO registers.

70 71 72
config LEDS_BCM6358
	tristate "LED Support for Broadcom BCM6358"
	depends on LEDS_CLASS
73
	depends on HAS_IOMEM
74 75 76 77 78
	depends on OF
	help
	  This option enables support for LEDs connected to the BCM6358
	  LED HW controller accessed via MMIO registers.

79 80 81 82 83 84 85 86 87 88
config LEDS_LM3530
	tristate "LCD Backlight driver for LM3530"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the LCD backlight using
	  LM3530 ambient light sensor chip. This ALS chip can be
	  controlled manually or using PWM input or using ambient
	  light automatically.

J
Johan Hovold 已提交
89 90 91 92 93 94 95 96 97 98 99 100 101
config LEDS_LM3533
	tristate "LED support for LM3533"
	depends on LEDS_CLASS
	depends on MFD_LM3533
	help
	  This option enables support for the LEDs on National Semiconductor /
	  TI LM3533 Lighting Power chips.

	  The LEDs can be controlled directly, through PWM input, or by the
	  ambient-light-sensor interface. The chip supports
	  hardware-accelerated blinking with maximum on and off periods of 9.8
	  and 77 seconds respectively.

102 103 104 105 106 107 108 109 110 111 112
config LEDS_LM3642
	tristate "LED support for LM3642 Chip"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to LM3642.
	  The LM3642 is a 4MHz fixed-frequency synchronous boost
	  converter plus 1.5A constant current driver for a high-current
	  white LED.


113 114
config LEDS_LOCOMO
	tristate "LED Support for Locomo device"
J
Johannes Berg 已提交
115
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
116
	depends on SHARP_LOCOMO
117 118 119 120
	help
	  This option enables support for the LEDs on Sharp Locomo.
	  Zaurus models SL-5500 and SL-5600.

121 122
config LEDS_MIKROTIK_RB532
	tristate "LED Support for Mikrotik Routerboard 532"
J
Johannes Berg 已提交
123
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
124
	depends on MIKROTIK_RB532
125 126 127 128
	help
	  This option enables support for the so called "User LED" of
	  Mikrotik's Routerboard 532.

129 130 131 132 133 134 135 136
config LEDS_MT6323
	tristate "LED Support for Mediatek MT6323 PMIC"
	depends on LEDS_CLASS
	depends on MFD_MT6397
	help
	  This option enables support for on-chip LED drivers found on
	  Mediatek MT6323 PMIC.

B
Ben Dooks 已提交
137 138
config LEDS_S3C24XX
	tristate "LED Support for Samsung S3C24XX GPIO LEDs"
J
Johannes Berg 已提交
139
	depends on LEDS_CLASS
140
	depends on ARCH_S3C24XX
B
Ben Dooks 已提交
141 142 143 144
	help
	  This option enables support for LEDs connected to GPIO lines
	  on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.

145 146
config LEDS_NET48XX
	tristate "LED Support for Soekris net48xx series Error LED"
J
Johannes Berg 已提交
147
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
148
	depends on SCx200_GPIO
149 150 151 152
	help
	  This option enables support for the Soekris net4801 and net4826 error
	  LED.

153 154
config LEDS_FSG
	tristate "LED Support for the Freecom FSG-3"
J
Johannes Berg 已提交
155
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
156
	depends on MACH_FSG
157 158 159
	help
	  This option enables support for the LEDs on the Freecom FSG-3.

160 161
config LEDS_WRAP
	tristate "LED Support for the WRAP series LEDs"
J
Johannes Berg 已提交
162
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
163
	depends on SCx200_GPIO
164 165 166
	help
	  This option enables support for the PCEngines WRAP programmable LEDs.

Y
Yoichi Yuasa 已提交
167 168
config LEDS_COBALT_QUBE
	tristate "LED Support for the Cobalt Qube series front LED"
J
Johannes Berg 已提交
169
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
170
	depends on MIPS_COBALT
171
	help
Y
Yoichi Yuasa 已提交
172
	  This option enables support for the front LED on Cobalt Qube series
173

174 175
config LEDS_COBALT_RAQ
	bool "LED Support for the Cobalt Raq series"
176
	depends on LEDS_CLASS=y && MIPS_COBALT
177 178 179 180
	select LEDS_TRIGGERS
	help
	  This option enables support for the Cobalt Raq series LEDs.

181 182
config LEDS_SUNFIRE
	tristate "LED support for SunFire servers."
J
Johannes Berg 已提交
183
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
184
	depends on SPARC64
185 186 187 188 189
	select LEDS_TRIGGERS
	help
	  This option enables support for the Left, Middle, and Right
	  LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.

190 191
config LEDS_IPAQ_MICRO
	tristate "LED Support for the Compaq iPAQ h3xxx"
192
	depends on LEDS_CLASS
193 194 195 196 197
	depends on MFD_IPAQ_MICRO
	help
	  Choose this option if you want to use the notification LED on
	  Compaq/HP iPAQ h3100 and h3600.

198 199
config LEDS_HP6XX
	tristate "LED Support for the HP Jornada 6xx"
J
Johannes Berg 已提交
200
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
201
	depends on SH_HP6XX
202
	help
203
	  This option enables LED support for the handheld
204 205
	  HP Jornada 620/660/680/690.

R
Riku Voipio 已提交
206 207
config LEDS_PCA9532
	tristate "LED driver for PCA9532 dimmer"
J
Johannes Berg 已提交
208
	depends on LEDS_CLASS
209
	depends on I2C && INPUT
R
Riku Voipio 已提交
210 211
	help
	  This option enables support for NXP pca9532
212
	  LED controller. It is generally only useful
R
Riku Voipio 已提交
213 214
	  as a platform driver

215 216 217 218 219 220 221 222 223 224
config LEDS_PCA9532_GPIO
	bool "Enable GPIO support for PCA9532"
	depends on LEDS_PCA9532
	depends on GPIOLIB
	help
	  Allow unused pins on PCA9532 to be used as gpio.

	  To use a pin as gpio pca9532_type in pca9532_platform data needs to
	  set to PCA9532_TYPE_GPIO.

225 226
config LEDS_GPIO
	tristate "LED Support for GPIO connected LEDs"
J
Johannes Berg 已提交
227
	depends on LEDS_CLASS
228
	depends on GPIOLIB || COMPILE_TEST
229 230 231
	help
	  This option enables support for the LEDs connected to GPIO
	  outputs. To be useful the particular board must have LEDs
232 233 234 235
	  and they must be connected to the GPIO lines.  The LEDs must be
	  defined as platform devices and/or OpenFirmware platform devices.
	  The code to use these bindings can be selected below.

236 237
config LEDS_LP3944
	tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
J
Johannes Berg 已提交
238
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
239
	depends on I2C
240
	help
241 242 243
	  This option enables support for LEDs connected to the National
	  Semiconductor LP3944 Lighting Management Unit (LMU) also known as
	  Fun Light Chip.
244 245 246 247

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp3944.

248 249 250 251 252 253 254 255 256 257 258 259 260
config LEDS_LP3952
	tristate "LED Support for TI LP3952 2 channel LED driver"
	depends on LEDS_CLASS
	depends on I2C
	depends on GPIOLIB
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to the Texas
	  Instruments LP3952 LED driver.

	  To compile this driver as a module, choose M here: the
	  module will be called leds-lp3952.

261
config LEDS_LP55XX_COMMON
262 263
	tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
	depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
264
	select FW_LOADER
265
	select FW_LOADER_USER_HELPER
266
	help
267
	  This option supports common operations for LP5521/5523/55231/5562/8501
268 269
	  devices.

270 271 272
config LEDS_LP5521
	tristate "LED Support for N.S. LP5521 LED driver chip"
	depends on LEDS_CLASS && I2C
273
	select LEDS_LP55XX_COMMON
274 275 276 277 278 279 280
	help
	  If you say yes here you get support for the National Semiconductor
	  LP5521 LED driver. It is 3 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

config LEDS_LP5523
281
	tristate "LED Support for TI/National LP5523/55231 LED driver chip"
282
	depends on LEDS_CLASS && I2C
283
	select LEDS_LP55XX_COMMON
284
	help
285 286 287
	  If you say yes here you get support for TI/National Semiconductor
	  LP5523/55231 LED driver.
	  It is 9 channel chip with programmable engines.
288 289 290
	  Driver provides direct control via LED class and interface for
	  programming the engines.

K
Kim, Milo 已提交
291 292 293 294 295 296 297 298 299 300
config LEDS_LP5562
	tristate "LED Support for TI LP5562 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP5562 LED driver.
	  It is 4 channels chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.

301 302 303 304 305 306 307 308 309 310 311 312
config LEDS_LP8501
	tristate "LED Support for TI LP8501 LED driver chip"
	depends on LEDS_CLASS && I2C
	select LEDS_LP55XX_COMMON
	help
	  If you say yes here you get support for TI LP8501 LED driver.
	  It is 9 channel chip with programmable engines.
	  Driver provides direct control via LED class and interface for
	  programming the engines.
	  It is similar as LP5523, but output power selection is available.
	  And register layout and engine program schemes are different.

K
Kim, Milo 已提交
313 314 315 316 317 318 319
config LEDS_LP8788
	tristate "LED support for the TI LP8788 PMIC"
	depends on LEDS_CLASS
	depends on MFD_LP8788
	help
	  This option enables support for the Keyboard LEDs on the LP8788 PMIC.

320 321
config LEDS_LP8860
	tristate "LED support for the TI LP8860 4 channel LED driver"
A
Axel Lin 已提交
322 323
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
324 325 326 327 328 329 330
	help
	  If you say yes here you get support for the TI LP8860 4 channel
	  LED driver.
	  This option enables support for the display cluster LEDs
	  on the LP8860 4 channel LED driver using the I2C communication
	  bus.

331
config LEDS_CLEVO_MAIL
332
	tristate "Mail LED on Clevo notebook"
J
Johannes Berg 已提交
333
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
334
	depends on X86 && SERIO_I8042 && DMI
335 336 337 338 339
	help
	  This driver makes the mail LED accessible from userspace
	  programs through the leds subsystem. This LED have three
	  known mode: off, blink at 0.5Hz and blink at 1Hz.

340 341 342 343 344
	  The driver supports two kinds of interface: using ledtrig-timer
	  or through /sys/class/leds/clevo::mail/brightness. As this LED
	  cannot change it's brightness it blinks instead. The brightness
	  value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
	  blink at 1Hz.
345 346 347

	  This module can drive the mail LED for the following notebooks:

348
	  	Clevo D400P
349 350 351 352 353 354 355
	  	Clevo D410J
	  	Clevo D410V
	  	Clevo D400V/D470V (not tested, but might work)
	  	Clevo M540N
	  	Clevo M5x0N (not tested, but might work)
	  	Positivo Mobile (Clevo M5x0V)

356
	  If your model is not listed here you can try the "nodetect"
357
	  module parameter.
358

359 360 361
	  To compile this driver as a module, choose M here: the
	  module will be called leds-clevo-mail.

362 363
config LEDS_PCA955X
	tristate "LED Support for PCA955x I2C chips"
J
Johannes Berg 已提交
364
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
365
	depends on I2C
366 367 368 369 370
	help
	  This option enables support for LEDs connected to PCA955x
	  LED driver chips accessed via the I2C bus.  Supported
	  devices include PCA9550, PCA9551, PCA9552, and PCA9553.

371
config LEDS_PCA963X
372
	tristate "LED support for PCA963x I2C chip"
373 374 375
	depends on LEDS_CLASS
	depends on I2C
	help
376 377 378
	  This option enables support for LEDs connected to the PCA963x
	  LED driver chip accessed via the I2C bus. Supported
	  devices include PCA9633 and PCA9634
379

M
Mark Brown 已提交
380 381
config LEDS_WM831X_STATUS
	tristate "LED support for status LEDs on WM831x PMICs"
J
Johannes Berg 已提交
382
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
383
	depends on MFD_WM831X
M
Mark Brown 已提交
384 385 386 387
	help
	  This option enables support for the status LEDs of the WM831x
          series of PMICs.

M
Mark Brown 已提交
388 389
config LEDS_WM8350
	tristate "LED Support for WM8350 AudioPlus PMIC"
J
Johannes Berg 已提交
390
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
391
	depends on MFD_WM8350
M
Mark Brown 已提交
392 393 394 395
	help
	  This option enables support for LEDs driven by the Wolfson
	  Microelectronics WM8350 AudioPlus PMIC.

396 397
config LEDS_DA903X
	tristate "LED Support for DA9030/DA9034 PMIC"
J
Johannes Berg 已提交
398
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
399
	depends on PMIC_DA903X
400 401 402 403
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9030/DA9034 PMICs.

404 405 406 407 408 409 410 411
config LEDS_DA9052
	tristate "Dialog DA9052/DA9053 LEDS"
	depends on LEDS_CLASS
	depends on PMIC_DA9052
	help
	  This option enables support for on-chip LED drivers found
	  on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.

412 413
config LEDS_DAC124S085
	tristate "LED Support for DAC124S085 SPI DAC"
J
Johannes Berg 已提交
414
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
415
	depends on SPI
416 417 418 419
	help
	  This option enables support for DAC124S085 SPI DAC from NatSemi,
	  which can be used to control up to four LEDs.

420 421
config LEDS_PWM
	tristate "PWM driven LED Support"
J
Johannes Berg 已提交
422
	depends on LEDS_CLASS
423
	depends on PWM
424 425 426
	help
	  This option enables support for pwm driven LEDs

427 428
config LEDS_REGULATOR
	tristate "REGULATOR driven LED support"
J
Johannes Berg 已提交
429
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
430
	depends on REGULATOR
431 432 433
	help
	  This option enables support for regulator driven LEDs.

K
Kim Kyuwon 已提交
434 435
config LEDS_BD2802
	tristate "LED driver for BD2802 RGB LED"
J
Johannes Berg 已提交
436
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
437
	depends on I2C
K
Kim Kyuwon 已提交
438 439 440 441
	help
	  This option enables support for BD2802GU RGB LED driver chips
	  accessed via the I2C bus.

442 443
config LEDS_INTEL_SS4200
	tristate "LED driver for Intel NAS SS4200 series"
J
Johannes Berg 已提交
444
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
445
	depends on PCI && DMI
446
	depends on X86
447 448
	help
	  This option enables support for the Intel SS4200 series of
449 450
	  Network Attached Storage servers. You may control the hard
	  drive or power LEDs on the front panel. Using this driver
451 452
	  can stop the front LED from blinking after startup.

453 454
config LEDS_LT3593
	tristate "LED driver for LT3593 controllers"
J
Johannes Berg 已提交
455
	depends on LEDS_CLASS
456
	depends on GPIOLIB || COMPILE_TEST
457 458 459 460 461
	help
	  This option enables support for LEDs driven by a Linear Technology
	  LT3593 controller. This controller uses a special one-wire pulse
	  coding protocol to set the brightness.

462 463
config LEDS_ADP5520
	tristate "LED Support for ADP5520/ADP5501 PMIC"
J
Johannes Berg 已提交
464
	depends on LEDS_CLASS
H
H Hartley Sweeten 已提交
465
	depends on PMIC_ADP5520
466 467 468 469 470 471 472
	help
	  This option enables support for on-chip LED drivers found
	  on Analog Devices ADP5520/ADP5501 PMICs.

	  To compile this driver as a module, choose M here: the module will
	  be called leds-adp5520.

473
config LEDS_MC13783
474
	tristate "LED Support for MC13XXX PMIC"
J
Johannes Berg 已提交
475
	depends on LEDS_CLASS
476
	depends on MFD_MC13XXX
477 478
	help
	  This option enable support for on-chip LED drivers found
479
	  on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
480

481 482
config LEDS_NS2
	tristate "LED support for Network Space v2 GPIO LEDs"
J
Johannes Berg 已提交
483
	depends on LEDS_CLASS
484
	depends on MACH_KIRKWOOD || MACH_ARMADA_370
485 486
	default y
	help
487 488 489 490 491 492 493
	  This option enables support for the dual-GPIO LEDs found on the
	  following LaCie/Seagate boards:

		Network Space v2 (and parents: Max, Mini)
		Internet Space v2
		d2 Network v2
		n090401 (Seagate NAS 4-Bay)
494

495 496
config LEDS_NETXBIG
	tristate "LED support for Big Network series LEDs"
497
	depends on LEDS_CLASS
498
	depends on MACH_KIRKWOOD
499 500 501 502 503 504
	default y
	help
	  This option enable support for LEDs found on the LaCie 2Big
	  and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
	  controlled through a GPIO extension bus.

P
Paul Parsons 已提交
505 506
config LEDS_ASIC3
	bool "LED support for the HTC ASIC3"
507
	depends on LEDS_CLASS=y
P
Paul Parsons 已提交
508 509 510 511 512 513 514 515
	depends on MFD_ASIC3
	default y
	help
	  This option enables support for the LEDs on the HTC ASIC3. The HTC
	  ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
	  cannot be used. This driver supports hardware blinking with an on+off
	  period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.

516 517 518 519 520 521 522 523
config LEDS_TCA6507
	tristate "LED Support for TCA6507 I2C chip"
	depends on LEDS_CLASS && I2C
	help
	  This option enables support for LEDs connected to TC6507
	  LED driver chips accessed via the I2C bus.
	  Driver support brightness control and hardware-assisted blinking.

524 525 526 527 528 529 530 531
config LEDS_TLC591XX
	tristate "LED driver for TLC59108 and TLC59116 controllers"
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
	  This option enables support for Texas Instruments TLC59108
	  and TLC59116 LED controllers.

532 533 534
config LEDS_MAX77693
	tristate "LED support for MAX77693 Flash"
	depends on LEDS_CLASS_FLASH
535
	depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
536 537 538 539 540 541 542
	depends on MFD_MAX77693
	depends on OF
	help
	  This option enables support for the flash part of the MAX77693
	  multifunction device. It has build in control for two leds in flash
	  and torch mode.

543 544 545 546 547 548 549
config LEDS_MAX8997
	tristate "LED support for MAX8997 PMIC"
	depends on LEDS_CLASS && MFD_MAX8997
	help
	  This option enables support for on-chip LED drivers on
	  MAXIM MAX8997 PMIC.

550 551
config LEDS_LM355x
	tristate "LED support for LM355x Chips, LM3554 and LM3556"
552 553 554
	depends on LEDS_CLASS && I2C
	select REGMAP_I2C
	help
555 556
	  This option enables support for LEDs connected to LM355x.
	  LM355x includes Torch, Flash and Indicator functions.
557

558 559
config LEDS_OT200
	tristate "LED support for the Bachmann OT200"
J
Jean Delvare 已提交
560
	depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
561 562 563 564
	help
	  This option enables support for the LEDs on the Bachmann OT200.
	  Say Y to enable LEDs on the Bachmann OT200.

565 566 567 568 569 570 571 572 573
config LEDS_MENF21BMC
	tristate "LED support for the MEN 14F021P00 BMC"
	depends on LEDS_CLASS && MFD_MENF21BMC
	help
	  Say Y here to include support for the MEN 14F021P00 BMC LEDs.

	  This driver can also be built as a module. If so the module
	  will be called leds-menf21bmc.

I
Ingi Kim 已提交
574 575
config LEDS_KTD2692
	tristate "LED support for KTD2692 flash LED controller"
576 577
	depends on LEDS_CLASS_FLASH && OF
	depends on GPIOLIB || COMPILE_TEST
I
Ingi Kim 已提交
578 579 580 581 582 583
	help
	  This option enables support for KTD2692 LED flash connected
	  through ExpressWire interface.

	  Say Y to enable this driver.

584 585 586 587 588 589 590 591 592 593
config LEDS_SEAD3
	tristate "LED support for the MIPS SEAD 3 board"
	depends on LEDS_CLASS && MIPS_SEAD3
	help
	  Say Y here to include support for the FLED and PLED LEDs on SEAD3 eval
	  boards.

	  This driver can also be built as a module. If so the module
	  will be called leds-sead3.

594 595 596 597 598 599 600 601 602 603 604 605
config LEDS_IS31FL319X
	tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
	depends on LEDS_CLASS && I2C && OF
	select REGMAP_I2C
	help
	  This option enables support for LEDs connected to ISSI IS31FL319x
	  fancy LED driver chips accessed via the I2C bus.
	  Driver supports individual PWM brightness control for each channel.

	  This driver can also be built as a module. If so the module will be
	  called leds-is31fl319x.

606 607 608 609
config LEDS_IS31FL32XX
	tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
	depends on LEDS_CLASS && I2C && OF
	help
610 611 612
	  Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
	  LED controllers. They are I2C devices with multiple constant-current
	  channels, each with independent 256-level PWM control.
613

614 615
comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"

616 617 618 619 620 621 622 623
config LEDS_BLINKM
	tristate "LED support for the BlinkM I2C RGB LED"
	depends on LEDS_CLASS
	depends on I2C
	help
	  This option enables support for the BlinkM RGB LED connected
	  through I2C. Say Y to enable support for the BlinkM LED.

624 625 626 627 628 629 630 631 632 633 634
config LEDS_POWERNV
	tristate "LED support for PowerNV Platform"
	depends on LEDS_CLASS
	depends on PPC_POWERNV
	depends on OF
	help
	  This option enables support for the system LEDs present on
	  PowerNV platforms. Say 'y' to enable this support in kernel.
	  To compile this driver as a module, choose 'm' here: the module
	  will be called leds-powernv.

635 636 637 638 639 640 641 642 643 644
config LEDS_SYSCON
	bool "LED support for LEDs on system controllers"
	depends on LEDS_CLASS=y
	depends on MFD_SYSCON
	depends on OF
	help
	  This option enabled support for the LEDs on syscon type
	  devices. This will only work with device tree enabled
	  devices.

645
config LEDS_VERSATILE
646
	tristate "LED support for the ARM Versatile and RealView"
647 648 649 650 651 652
	depends on ARCH_REALVIEW || ARCH_VERSATILE
	depends on LEDS_CLASS
	help
	  This option enabled support for the LEDs on the ARM Versatile
	  and RealView boards. Say Y to enabled these.

L
Linus Walleij 已提交
653 654
config LEDS_PM8058
	tristate "LED Support for the Qualcomm PM8058 PMIC"
655
	depends on MFD_PM8XXX
L
Linus Walleij 已提交
656 657 658 659 660
	depends on LEDS_CLASS
	help
	  Choose this option if you want to use the LED drivers in
	  the Qualcomm PM8058 PMIC.

661 662 663 664 665 666 667 668
config LEDS_MLXCPLD
	tristate "LED support for the Mellanox boards"
	depends on X86_64 && DMI
	depends on LEDS_CLASS
	help
	  This option enabled support for the LEDs on the Mellanox
	  boards. Say Y to enabled these.

669 670 671 672 673 674 675 676
config LEDS_USER
	tristate "Userspace LED support"
	depends on LEDS_CLASS
	help
	  This option enables support for userspace LEDs. Say 'y' to enable this
	  support in kernel. To compile this driver as a module, choose 'm' here:
	  the module will be called uleds.

677 678 679 680 681 682 683 684 685 686 687
config LEDS_NIC78BX
	tristate "LED support for NI PXI NIC78bx devices"
	depends on LEDS_CLASS
	depends on X86 && ACPI
	help
	  This option enables support for the User1 and User2 LEDs on NI
	  PXI NIC78bx devices.

	  To compile this driver as a module, choose M here: the module
	  will be called leds-nic78bx.

H
H Hartley Sweeten 已提交
688
comment "LED Triggers"
689
source "drivers/leds/trigger/Kconfig"
690

691
endif # NEW_LEDS