Kconfig 27.8 KB
Newer Older
1
source "arch/powerpc/platforms/Kconfig.cputype"
2

3 4 5 6
config PPC32
	bool
	default y if !PPC64

7 8 9 10
config 32BIT
	bool
	default y if PPC32

11 12 13 14
config 64BIT
	bool
	default y if PPC64

15 16 17 18 19
config WORD_SIZE
	int
	default 64 if PPC64
	default 32 if !PPC64

20 21 22
config ARCH_PHYS_ADDR_T_64BIT
       def_bool PPC64 || PHYS_64BIT

23 24 25
config ARCH_DMA_ADDR_T_64BIT
	def_bool ARCH_PHYS_ADDR_T_64BIT

26 27 28 29
config MMU
	bool
	default y

30
config HAVE_SETUP_PER_CPU_AREA
31 32
	def_bool PPC64

33
config NEED_PER_CPU_EMBED_FIRST_CHUNK
34 35
	def_bool PPC64

36 37
config NR_IRQS
	int "Number of virtual interrupt numbers"
38
	range 32 32768
39 40 41 42 43 44 45
	default "512"
	help
	  This defines the number of virtual interrupt numbers the kernel
	  can manage. Virtual interrupt numbers are what you see in
	  /proc/interrupts. If you configure your system to have too few,
	  drivers will fail to load or worse - handle with care.

46 47 48 49
config STACKTRACE_SUPPORT
	bool
	default y

A
Arnd Bergmann 已提交
50 51 52
config HAVE_LATENCYTOP_SUPPORT
	def_bool y

53 54 55 56 57 58 59 60
config TRACE_IRQFLAGS_SUPPORT
	bool
	default y

config LOCKDEP_SUPPORT
	bool
	default y

61 62 63 64 65 66 67
config RWSEM_GENERIC_SPINLOCK
	bool

config RWSEM_XCHGADD_ALGORITHM
	bool
	default y

N
Nick Piggin 已提交
68 69 70 71 72
config GENERIC_LOCKBREAK
	bool
	default y
	depends on SMP && PREEMPT

73 74
config ARCH_HAS_ILOG2_U32
	bool
75
	default y
76 77 78

config ARCH_HAS_ILOG2_U64
	bool
79
	default y if 64BIT
80

81 82 83 84
config GENERIC_HWEIGHT
	bool
	default y

85 86 87
config PPC
	bool
	default y
88
	select ARCH_MIGHT_HAVE_PC_PARPORT
89
	select ARCH_MIGHT_HAVE_PC_SERIO
90
	select BINFMT_ELF
91
	select OF
92
	select OF_EARLY_FLATTREE
93
	select OF_RESERVED_MEM
S
Steven Rostedt 已提交
94 95
	select HAVE_FTRACE_MCOUNT_RECORD
	select HAVE_DYNAMIC_FTRACE
96
	select HAVE_FUNCTION_TRACER
97
	select HAVE_FUNCTION_GRAPH_TRACER
98
	select SYSCTL_EXCEPTION_TRACE
M
Michael Buesch 已提交
99
	select ARCH_WANT_OPTIONAL_GPIOLIB
100
	select VIRT_TO_BUS if !PPC64
S
Sam Ravnborg 已提交
101
	select HAVE_IDE
B
Benjamin Herrenschmidt 已提交
102
	select HAVE_IOREMAP_PROT
103
	select HAVE_EFFICIENT_UNALIGNED_ACCESS if !CPU_LITTLE_ENDIAN
M
Mathieu Desnoyers 已提交
104
	select HAVE_KPROBES
105
	select HAVE_ARCH_KGDB
106
	select HAVE_KRETPROBES
107
	select HAVE_ARCH_TRACEHOOK
Y
Yinghai Lu 已提交
108
	select HAVE_MEMBLOCK
T
Tejun Heo 已提交
109
	select HAVE_MEMBLOCK_NODE_MAP
110
	select HAVE_DMA_ATTRS
111
	select HAVE_DMA_API_DEBUG
S
Steven Rostedt 已提交
112
	select HAVE_OPROFILE
113
	select HAVE_DEBUG_KMEMLEAK
114
	select GENERIC_ATOMIC64 if PPC32
115
	select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
116
	select HAVE_PERF_EVENTS
117
	select HAVE_REGS_AND_STACK_ACCESS_API
118
	select HAVE_HW_BREAKPOINT if PERF_EVENTS && PPC_BOOK3S_64
119
	select ARCH_WANT_IPC_PARSE_VERSION
G
Grant Likely 已提交
120
	select SPARSE_IRQ
121
	select IRQ_DOMAIN
122 123
	select GENERIC_IRQ_SHOW
	select GENERIC_IRQ_SHOW_LEVEL
T
Thomas Gleixner 已提交
124
	select IRQ_FORCED_THREADING
125
	select HAVE_RCU_TABLE_FREE if SMP
126
	select HAVE_SYSCALL_TRACEPOINTS
127
	select HAVE_BPF_JIT if PPC64
128
	select HAVE_ARCH_JUMP_LABEL
129
	select ARCH_HAVE_NMI_SAFE_CMPXCHG
130
	select GENERIC_SMP_IDLE_THREAD
131
	select GENERIC_CMOS_UPDATE
132
	select GENERIC_TIME_VSYSCALL_OLD
133
	select GENERIC_CLOCKEVENTS
134 135
	select GENERIC_CLOCKEVENTS_BROADCAST if SMP
	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
136 137
	select GENERIC_STRNCPY_FROM_USER
	select GENERIC_STRNLEN_USER
138 139
	select HAVE_MOD_ARCH_SPECIFIC
	select MODULES_USE_ELF_RELA
140
	select CLONE_BACKWARDS
141
	select ARCH_USE_BUILTIN_BSWAP
142
	select OLD_SIGSUSPEND
143
	select OLD_SIGACTION if PPC32
144
	select HAVE_DEBUG_STACKOVERFLOW
145
	select HAVE_IRQ_EXIT_ON_IRQ_STACK
146
	select ARCH_USE_CMPXCHG_LOCKREF if PPC64
147
	select HAVE_ARCH_AUDITSYSCALL
148

149 150 151
config GENERIC_CSUM
	def_bool CPU_LITTLE_ENDIAN

152 153
config EARLY_PRINTK
	bool
154
	default y
155

156 157 158 159
config PANIC_TIMEOUT
	int
	default 180

160 161 162
config COMPAT
	bool
	default y if PPC64
163
	select COMPAT_BINFMT_ELF
164
	select ARCH_WANT_OLD_COMPAT_IPC
165
	select COMPAT_OLD_SIGACTION
166 167 168 169 170 171 172 173 174 175 176

config SYSVIPC_COMPAT
	bool
	depends on COMPAT && SYSVIPC
	default y

# All PPC32s use generic nvram driver through ppc_md
config GENERIC_NVRAM
	bool
	default y if PPC32

177
config SCHED_OMIT_FRAME_POINTER
178 179 180 181 182
	bool
	default y

config ARCH_MAY_HAVE_PC_FDC
	bool
183
	default !PPC_PSERIES || PCI
184

185 186 187 188 189 190 191 192 193 194 195 196
config PPC_OF
	def_bool y

config PPC_UDBG_16550
	bool
	default n

config GENERIC_TBSYNC
	bool
	default y if PPC32 && SMP
	default n

197 198 199 200
config AUDIT_ARCH
	bool
	default y

201 202 203 204 205
config GENERIC_BUG
	bool
	default y
	depends on BUG

206
config SYS_SUPPORTS_APM_EMULATION
K
Kumar Gala 已提交
207
	default y if PMAC_APM_EMU
208 209
	bool

210 211 212 213 214 215
config EPAPR_BOOT
	bool
	help
	  Used to allow a board to specify it wants an ePAPR compliant wrapper.
	default n

216 217 218 219 220 221
config DEFAULT_UIMAGE
	bool
	help
	  Used to allow a board to specify it wants a uImage built by default
	default n

222 223
config ARCH_HIBERNATION_POSSIBLE
	bool
224 225
	default y

J
Johannes Berg 已提交
226 227
config ARCH_SUSPEND_POSSIBLE
	def_bool y
228
	depends on ADB_PMU || PPC_EFIKA || PPC_LITE5200 || PPC_83xx || \
229 230
		   (PPC_85xx && !PPC_E500MC) || PPC_86xx || PPC_PSERIES \
		   || 44x || 40x
J
Johannes Berg 已提交
231

232 233 234 235 236 237 238 239 240 241 242 243 244
config PPC_DCR_NATIVE
	bool
	default n

config PPC_DCR_MMIO
	bool
	default n

config PPC_DCR
	bool
	depends on PPC_DCR_NATIVE || PPC_DCR_MMIO
	default y

245 246
config PPC_OF_PLATFORM_PCI
	bool
247
	depends on PCI
248 249 250
	depends on PPC64 # not supported on 32 bits yet
	default n

A
Akinobu Mita 已提交
251 252 253
config ARCH_SUPPORTS_DEBUG_PAGEALLOC
	def_bool y

254 255 256
config ARCH_SUPPORTS_UPROBES
	def_bool y

257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283
config PPC_ADV_DEBUG_REGS
	bool
	depends on 40x || BOOKE
	default y

config PPC_ADV_DEBUG_IACS
	int
	depends on PPC_ADV_DEBUG_REGS
	default 4 if 44x
	default 2

config PPC_ADV_DEBUG_DACS
	int
	depends on PPC_ADV_DEBUG_REGS
	default 2

config PPC_ADV_DEBUG_DVCS
	int
	depends on PPC_ADV_DEBUG_REGS
	default 2 if 44x
	default 0

config PPC_ADV_DEBUG_DAC_RANGE
	bool
	depends on PPC_ADV_DEBUG_REGS && 44x
	default y

284 285 286 287
config PPC_EMULATE_SSTEP
	bool
	default y if KPROBES || UPROBES || XMON || HAVE_HW_BREAKPOINT

288 289
source "init/Kconfig"

290 291
source "kernel/Kconfig.freezer"

292
source "arch/powerpc/sysdev/Kconfig"
293
source "arch/powerpc/platforms/Kconfig"
294 295 296 297 298 299 300 301 302 303 304

menu "Kernel options"

config HIGHMEM
	bool "High memory support"
	depends on PPC32

source kernel/Kconfig.hz
source kernel/Kconfig.preempt
source "fs/Kconfig.binfmt"

305 306 307 308 309
config HUGETLB_PAGE_SIZE_VARIABLE
	bool
	depends on HUGETLB_PAGE
	default y

310 311
config MATH_EMULATION
	bool "Math emulation"
312
	depends on 4xx || 8xx || PPC_MPC832x || BOOKE
313 314 315 316 317 318 319 320
	---help---
	  Some PowerPC chips designed for embedded applications do not have
	  a floating-point unit and therefore do not implement the
	  floating-point instructions in the PowerPC instruction set.  If you
	  say Y here, the kernel will include code to emulate a floating-point
	  unit, which will allow programs that use floating-point
	  instructions to run.

321 322 323 324
	  This is also useful to emulate missing (optional) instructions
	  such as fsqrt on cores that do have an FPU but do not implement
	  them (such as Freescale BookE).

325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344
choice
	prompt "Math emulation options"
	default MATH_EMULATION_FULL
	depends on MATH_EMULATION

config	MATH_EMULATION_FULL
	bool "Emulate all the floating point instructions"
	---help---
	  Select this option will enable the kernel to support to emulate
	  all the floating point instructions. If your SoC doesn't have
	  a FPU, you should select this.

config MATH_EMULATION_HW_UNIMPLEMENTED
	bool "Just emulate the FPU unimplemented instructions"
	---help---
	  Select this if you know there does have a hardware FPU on your
	  SoC, but some floating point instructions are not implemented by that.

endchoice

345 346 347 348
config PPC_TRANSACTIONAL_MEM
       bool "Transactional Memory support for POWERPC"
       depends on PPC_BOOK3S_64
       depends on SMP
349 350
       select ALTIVEC
       select VSX
351 352 353 354
       default n
       ---help---
         Support user-mode Transactional Memory on POWERPC.

355 356 357
config IOMMU_HELPER
	def_bool PPC64

358 359 360 361 362 363 364 365 366 367
config SWIOTLB
	bool "SWIOTLB support"
	default n
	select IOMMU_HELPER
	---help---
	  Support for IO bounce buffering for systems without an IOMMU.
	  This allows us to DMA to the full physical address space on
	  platforms where the size of a physical address is larger
	  than the bus address.  Not all platforms support this.

368 369
config HOTPLUG_CPU
	bool "Support for enabling/disabling CPUs"
370
	depends on SMP && (PPC_PSERIES || \
371
	PPC_PMAC || PPC_POWERNV || (PPC_85xx && !PPC_E500MC))
372 373 374 375 376 377
	---help---
	  Say Y here to be able to disable and re-enable individual
	  CPUs at runtime on SMP machines.

	  Say N if you are unsure.

378 379 380 381
config ARCH_CPU_PROBE_RELEASE
	def_bool y
	depends on HOTPLUG_CPU

382 383 384
config ARCH_ENABLE_MEMORY_HOTPLUG
	def_bool y

385 386 387
config ARCH_HAS_WALK_MEMORY
	def_bool y

388 389 390
config ARCH_ENABLE_MEMORY_HOTREMOVE
	def_bool y

391 392 393 394 395 396
config PPC64_SUPPORTS_MEMORY_FAILURE
	bool "Add support for memory hwpoison"
	depends on PPC_BOOK3S_64
	default "y" if PPC_POWERNV
	select ARCH_SUPPORTS_MEMORY_FAILURE

397
config KEXEC
398 399
	bool "kexec system call"
	depends on (PPC_BOOK3S || FSL_BOOKE || (44x && !SMP))
400 401 402
	help
	  kexec is a system call that implements the ability to shutdown your
	  current kernel, and to start another kernel.  It is like a reboot
403
	  but it is independent of the system firmware.   And like a reboot
404 405
	  you can start any kernel with it, not just Linux.

406
	  The name comes from the similarity to the exec system call.
407 408 409

	  It is an ongoing process to be certain the hardware in a machine
	  is properly shutdown, so do not be surprised if this code does not
410 411 412
	  initially work for you.  As of this writing the exact hardware
	  interface is strongly in flux, so no good recommendation can be
	  made.
413

414
config CRASH_DUMP
415
	bool "Build a kdump crash kernel"
S
Suzuki Poulose 已提交
416
	depends on PPC64 || 6xx || FSL_BOOKE || (44x && !SMP)
417
	select RELOCATABLE if (PPC64 && !COMPILE_TEST) || 44x || FSL_BOOKE
418 419
	help
	  Build a kernel suitable for use as a kdump capture kernel.
420 421
	  The same kernel binary can be used as production kernel and dump
	  capture kernel.
422

423 424
config FA_DUMP
	bool "Firmware-assisted dump"
425
	depends on PPC64 && PPC_RTAS && CRASH_DUMP && KEXEC
426
	help
427 428 429 430 431 432
	  A robust mechanism to get reliable kernel crash dump with
	  assistance from firmware. This approach does not use kexec,
	  instead firmware assists in booting the kdump kernel
	  while preserving memory contents. Firmware-assisted dump
	  is meant to be a kdump replacement offering robustness and
	  speed not possible without system firmware assistance.
433 434 435

	  If unsure, say "N"

436 437
config IRQ_ALL_CPUS
	bool "Distribute interrupts on all CPUs by default"
P
Paul Bolle 已提交
438
	depends on SMP
439 440 441 442 443 444
	help
	  This option gives the kernel permission to distribute IRQs across
	  multiple CPUs.  Saying N here will route all IRQs to the first
	  CPU.  Generally saying Y is safe, although some problems have been
	  reported with SMP Power Macintoshes with this option enabled.

445 446 447 448 449
config NUMA
	bool "NUMA support"
	depends on PPC64
	default y if SMP && PPC_PSERIES

Y
Yasunori Goto 已提交
450 451
config NODES_SHIFT
	int
452
	default "8" if PPC64
Y
Yasunori Goto 已提交
453 454 455
	default "4"
	depends on NEED_MULTIPLE_NODES

456 457 458 459
config USE_PERCPU_NUMA_NODE_ID
	def_bool y
	depends on NUMA

460 461 462 463
config HAVE_MEMORYLESS_NODES
	def_bool y
	depends on NUMA

464 465 466 467 468
config ARCH_SELECT_MEMORY_MODEL
	def_bool y
	depends on PPC64

config ARCH_FLATMEM_ENABLE
469 470
	def_bool y
	depends on (PPC64 && !NUMA) || PPC32
471

472
config ARCH_SPARSEMEM_ENABLE
473
	def_bool y
474
	depends on PPC64
A
Andy Whitcroft 已提交
475
	select SPARSEMEM_VMEMMAP_ENABLE
476

477
config ARCH_SPARSEMEM_DEFAULT
478
	def_bool y
479
	depends on (SMP && PPC_PSERIES) || PPC_PS3
480

481
config SYS_SUPPORTS_HUGETLBFS
B
Becky Bruce 已提交
482
	bool
483

484
source "mm/Kconfig"
485

M
Mike Kravetz 已提交
486 487 488 489
config ARCH_MEMORY_PROBE
	def_bool y
	depends on MEMORY_HOTPLUG

490 491 492 493 494 495 496 497 498
# Some NUMA nodes have memory ranges that span
# other nodes.  Even though a pfn is valid and
# between a node's start and end pfns, it may not
# reside on that node.  See memmap_init_zone()
# for details.
config NODES_SPAN_OTHER_NODES
	def_bool y
	depends on NEED_MULTIPLE_NODES

499 500 501 502 503
config PPC_HAS_HASH_64K
	bool
	depends on PPC64
	default n

504 505 506 507 508 509 510 511 512 513 514 515
config STDBINUTILS
	bool "Using standard binutils settings"
	depends on 44x
	default y
	help
	  Turning this option off allows you to select 256KB PAGE_SIZE on 44x.
	  Note, that kernel will be able to run only those applications,
	  which had been compiled using binutils later than 2.17.50.0.3 with
	  '-zmax-page-size' set to 256K (the default is 64K). Or, if using
	  the older binutils, you can patch them with a trivial patch, which
	  changes the ELF_MAXPAGESIZE definition from 0x10000 to 0x40000.

516 517 518
choice
	prompt "Page size"
	default PPC_4K_PAGES
519
	help
520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547
	  Select the kernel logical page size. Increasing the page size
	  will reduce software overhead at each page boundary, allow
	  hardware prefetch mechanisms to be more effective, and allow
	  larger dma transfers increasing IO efficiency and reducing
	  overhead. However the utilization of memory will increase.
	  For example, each cached file will using a multiple of the
	  page size to hold its contents and the difference between the
	  end of file and the end of page is wasted.

	  Some dedicated systems, such as software raid serving with
	  accelerated calculations, have shown significant increases.

	  If you configure a 64 bit kernel for 64k pages but the
	  processor does not support them, then the kernel will simulate
	  them with 4k pages, loading them on demand, but with the
	  reduced software overhead and larger internal fragmentation.
	  For the 32 bit kernel, a large page option will not be offered
	  unless it is supported by the configured processor.

	  If unsure, choose 4K_PAGES.

config PPC_4K_PAGES
	bool "4k page size"

config PPC_16K_PAGES
	bool "16k page size" if 44x

config PPC_64K_PAGES
548
	bool "64k page size" if 44x || PPC_STD_MMU_64 || PPC_BOOK3E_64
549
	depends on !PPC_FSL_BOOK3E
550 551
	select PPC_HAS_HASH_64K if PPC_STD_MMU_64

552 553
config PPC_256K_PAGES
	bool "256k page size" if 44x
554
	depends on !STDBINUTILS
555 556 557 558 559 560 561 562 563 564
	help
	  Make the page size 256k.

	  As the ELF standard only requires alignment to support page
	  sizes up to 64k, you will need to compile all of your user
	  space applications with a non-standard binutils settings
	  (see the STDBINUTILS description for details).

	  Say N unless you know what you are doing.

565
endchoice
566

567 568
config FORCE_MAX_ZONEORDER
	int "Maximum zone order"
569 570 571 572 573 574 575 576 577 578
	range 9 64 if PPC64 && PPC_64K_PAGES
	default "9" if PPC64 && PPC_64K_PAGES
	range 13 64 if PPC64 && !PPC_64K_PAGES
	default "13" if PPC64 && !PPC_64K_PAGES
	range 9 64 if PPC32 && PPC_16K_PAGES
	default "9" if PPC32 && PPC_16K_PAGES
	range 7 64 if PPC32 && PPC_64K_PAGES
	default "7" if PPC32 && PPC_64K_PAGES
	range 5 64 if PPC32 && PPC_256K_PAGES
	default "5" if PPC32 && PPC_256K_PAGES
J
Johannes Berg 已提交
579
	range 11 64
580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595
	default "11"
	help
	  The kernel memory allocator divides physically contiguous memory
	  blocks into "zones", where each zone is a power of two number of
	  pages.  This option selects the largest power of two that the kernel
	  keeps in the memory allocator.  If you need to allocate very large
	  blocks of physically contiguous memory, then you may need to
	  increase this value.

	  This config option is actually maximum order plus one. For example,
	  a value of 11 means that the largest free memory block is 2^10 pages.

	  The page size is not necessarily 4KB.  For example, on 64-bit
	  systems, 64KB pages can be enabled via CONFIG_PPC_64K_PAGES.  Keep
	  this in mind when choosing a value for this option.

596 597
config PPC_SUBPAGE_PROT
	bool "Support setting protections for 4k subpages"
598
	depends on PPC_STD_MMU_64 && PPC_64K_PAGES
599 600 601 602 603
	help
	  This option adds support for a system call to allow user programs
	  to set access permissions (read/write, readonly, or no access)
	  on the 4k subpages of each 64k page.

604 605 606 607 608 609 610 611
config SCHED_SMT
	bool "SMT (Hyperthreading) scheduler support"
	depends on PPC64 && SMP
	help
	  SMT scheduler support improves the CPU scheduler's decision making
	  when dealing with POWER5 cpus at a cost of slightly increased
	  overhead in some places. If unsure say N here.

612 613 614
config PPC_DENORMALISATION
	bool "PowerPC denormalisation exception handling"
	depends on PPC_BOOK3S_64
615
	default "y" if PPC_POWERNV
616 617 618 619
	---help---
	  Add support for handling denormalisation of single precision
	  values.  Useful for bare metal only.  If unsure say Y here.

620 621 622 623 624 625 626 627 628 629 630 631 632
config CMDLINE_BOOL
	bool "Default bootloader kernel arguments"

config CMDLINE
	string "Initial kernel command string"
	depends on CMDLINE_BOOL
	default "console=ttyS0,9600 console=tty0 root=/dev/sda2"
	help
	  On some platforms, there is currently no way for the boot loader to
	  pass arguments to the kernel. For these platforms, you can supply
	  some command-line options at build time by entering them here.  In
	  most cases you will need to specify the root device here.

633 634 635 636 637 638 639 640 641
config CMDLINE_FORCE
	bool "Always use the default kernel command string"
	depends on CMDLINE_BOOL
	help
	  Always use the default kernel command string, even if the boot
	  loader passes other arguments to the kernel.
	  This is useful if you cannot or don't want to change the
	  command-line options your boot loader passes to the kernel.

642 643 644 645 646 647 648 649 650 651 652 653 654
config EXTRA_TARGETS
	string "Additional default image types"
	help
	  List additional targets to be built by the bootwrapper here (separated
	  by spaces).  This is useful for targets that depend of device tree
	  files in the .dts directory.

	  Targets in this list will be build as part of the default build
	  target, or when the user does a 'make zImage' or a
	  'make zImage.initrd'.

	  If unsure, leave blank

655 656 657 658
config ARCH_WANTS_FREEZER_CONTROL
	def_bool y
	depends on ADB_PMU

659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681
source kernel/power/Kconfig

config SECCOMP
	bool "Enable seccomp to safely compute untrusted bytecode"
	depends on PROC_FS
	default y
	help
	  This kernel feature is useful for number crunching applications
	  that may need to compute untrusted bytecode during their
	  execution. By using pipes or other transports made available to
	  the process as file descriptors supporting the read/write
	  syscalls, it's possible to isolate those applications in
	  their own address space using seccomp. Once seccomp is
	  enabled via /proc/<pid>/seccomp, it cannot be disabled
	  and the task is only allowed to execute a few safe syscalls
	  defined by each seccomp mode.

	  If unsure, say Y. Only embedded should say N here.

endmenu

config ISA_DMA_API
	bool
682
	default PCI
683 684 685 686 687

menu "Bus options"

config ISA
	bool "Support for ISA-bus hardware"
P
Paul Bolle 已提交
688
	depends on PPC_CHRP
689
	select PPC_I8259
690 691 692 693
	help
	  Find out whether you have ISA slots on your motherboard.  ISA is the
	  name of a bus system, i.e. the way the CPU talks to the other stuff
	  inside your box.  If you have an Apple machine, say N here; if you
P
Paul Bolle 已提交
694 695
	  have an IBM RS/6000 or pSeries machine, say Y.  If you have an
	  embedded board, consult your board documentation.
696

697 698 699 700
config ZONE_DMA
	bool
	default y

701 702 703
config NEED_DMA_MAP_STATE
	def_bool (PPC64 || NOT_COHERENT_CACHE)

704 705 706
config NEED_SG_DMA_LENGTH
	def_bool y

707 708
config GENERIC_ISA_DMA
	bool
709
	depends on ISA_DMA_API
710 711
	default y

712 713 714
config PPC_INDIRECT_PCI
	bool
	depends on PCI
715
	default y if 40x || 44x
716 717
	default n

718 719 720 721 722 723
config EISA
	bool

config SBUS
	bool

724 725 726
config FSL_SOC
	bool

727 728 729
config FSL_PCI
 	bool
	select PPC_INDIRECT_PCI
730
	select PCI_QUIRKS
731

732 733 734 735 736 737 738 739
config FSL_PMC
	bool
	default y
	depends on SUSPEND && (PPC_85xx || PPC_86xx)
	help
	  Freescale MPC85xx/MPC86xx power management controller support
	  (suspend/resume). For MPC83xx see platforms/83xx/suspend.c

740 741 742 743 744 745 746 747 748
config PPC4xx_CPM
	bool
	default y
	depends on SUSPEND && (44x || 40x)
	help
	  PPC4xx Clock Power Management (CPM) support (suspend/resume).
	  It also enables support for two different idle states (idle-wait
	  and idle-doze).

749 750 751
config 4xx_SOC
	bool

752
config FSL_LBC
753 754
	bool "Freescale Local Bus support"
	depends on FSL_SOC
755
	help
756 757 758
	  Enables reporting of errors from the Freescale local bus
	  controller.  Also contains some common code used by
	  drivers for specific local bus peripherals.
759

760 761 762 763 764 765
config FSL_GTM
	bool
	depends on PPC_83xx || QUICC_ENGINE || CPM2
	help
	  Freescale General-purpose Timers support

766 767 768 769
# Yes MCA RS/6000s exist but Linux-PPC does not currently support any
config MCA
	bool

J
John Rigby 已提交
770 771 772 773 774 775
# Platforms that what PCI turned unconditionally just do select PCI
# in their config node.  Platforms that want to choose at config
# time should select PPC_PCI_CHOICE
config PPC_PCI_CHOICE
	bool

776
config PCI
J
John Rigby 已提交
777 778
	bool "PCI support" if PPC_PCI_CHOICE
	default y if !40x && !CPM2 && !8xx && !PPC_83xx \
779
		&& !PPC_85xx && !PPC_86xx && !GAMECUBE_COMMON
780
	default PCI_QSPAN if !4xx && !CPM2 && 8xx
781
	select GENERIC_PCI_IOMAP
782 783 784 785 786 787 788
	help
	  Find out whether your system includes a PCI bus. PCI is the name of
	  a bus system, i.e. the way the CPU talks to the other stuff inside
	  your box.  If you say Y here, the kernel will include drivers and
	  infrastructure code to support PCI bus devices.

config PCI_DOMAINS
789 790 791 792
	def_bool PCI

config PCI_SYSCALL
	def_bool PCI
793 794 795 796

config PCI_QSPAN
	bool "QSpan PCI"
	depends on !4xx && !CPM2 && 8xx
797
	select PPC_I8259
798 799 800 801 802 803 804
	help
	  Say Y here if you have a system based on a Motorola 8xx-series
	  embedded processor with a QSPAN PCI interface, otherwise say N.

config PCI_8260
	bool
	depends on PCI && 8260
805
	select PPC_INDIRECT_PCI
806 807
	default y

808 809
source "drivers/pci/pcie/Kconfig"

810 811 812 813 814 815
source "drivers/pci/Kconfig"

source "drivers/pcmcia/Kconfig"

source "drivers/pci/hotplug/Kconfig"

816 817 818 819 820
config HAS_RAPIDIO
	bool
	default n

config RAPIDIO
821
	tristate "RapidIO support"
822
	depends on HAS_RAPIDIO || PCI
823 824 825 826
	help
	  If you say Y here, the kernel will include drivers and
	  infrastructure code to support RapidIO interconnect devices.

827 828
config FSL_RIO
	bool "Freescale Embedded SRIO Controller support"
829
	depends on RAPIDIO = y && HAS_RAPIDIO
830 831 832 833 834
	default "n"
	---help---
	  Include support for RapidIO controller on Freescale embedded
	  processors (MPC8548, MPC8641, etc).

835 836
source "drivers/rapidio/Kconfig"

837 838
endmenu

839 840 841 842
config NONSTATIC_KERNEL
	bool
	default n

843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874
menu "Advanced setup"
	depends on PPC32

config ADVANCED_OPTIONS
	bool "Prompt for advanced kernel configuration options"
	help
	  This option will enable prompting for a variety of advanced kernel
	  configuration options.  These options can cause the kernel to not
	  work if they are set incorrectly, but can be used to optimize certain
	  aspects of kernel memory management.

	  Unless you know what you are doing, say N here.

comment "Default settings for advanced configuration options are used"
	depends on !ADVANCED_OPTIONS

config LOWMEM_SIZE_BOOL
	bool "Set maximum low memory"
	depends on ADVANCED_OPTIONS
	help
	  This option allows you to set the maximum amount of memory which
	  will be used as "low memory", that is, memory which the kernel can
	  access directly, without having to set up a kernel virtual mapping.
	  This can be useful in optimizing the layout of kernel virtual
	  memory.

	  Say N here unless you know what you are doing.

config LOWMEM_SIZE
	hex "Maximum low memory size (in bytes)" if LOWMEM_SIZE_BOOL
	default "0x30000000"

875 876 877 878 879 880 881 882 883 884 885 886 887
config LOWMEM_CAM_NUM_BOOL
	bool "Set number of CAMs to use to map low memory"
	depends on ADVANCED_OPTIONS && FSL_BOOKE
	help
	  This option allows you to set the maximum number of CAM slots that
	  will be used to map low memory.  There are a limited number of slots
	  available and even more limited number that will fit in the L1 MMU.
	  However, using more entries will allow mapping more low memory.  This
	  can be useful in optimizing the layout of kernel virtual memory.

	  Say N here unless you know what you are doing.

config LOWMEM_CAM_NUM
888
	depends on FSL_BOOKE
889 890 891
	int "Number of CAMs to use to map low memory" if LOWMEM_CAM_NUM_BOOL
	default 3

892
config DYNAMIC_MEMSTART
893 894
	bool "Enable page aligned dynamic load address for kernel"
	depends on ADVANCED_OPTIONS && FLATMEM && (FSL_BOOKE || 44x)
895 896 897 898 899 900 901 902 903 904 905 906 907
	select NONSTATIC_KERNEL
	help
	  This option enables the kernel to be loaded at any page aligned
	  physical address. The kernel creates a mapping from KERNELBASE to 
	  the address where the kernel is loaded. The page size here implies
	  the TLB page size of the mapping for kernel on the particular platform.
	  Please refer to the init code for finding the TLB page size.

	  DYNAMIC_MEMSTART is an easy way of implementing pseudo-RELOCATABLE
	  kernel image, where the only restriction is the page aligned kernel
	  load address. When this option is enabled, the compile time physical 
	  address CONFIG_PHYSICAL_START is ignored.

908 909
	  This option is overridden by CONFIG_RELOCATABLE

910
config RELOCATABLE
911
	bool "Build a relocatable kernel"
912
	depends on ADVANCED_OPTIONS && FLATMEM && (44x || FSL_BOOKE)
913
	select NONSTATIC_KERNEL
914 915
	help
	  This builds a kernel image that is capable of running at the
916 917
	  location the kernel is loaded at, without any alignment restrictions.
	  This feature is a superset of DYNAMIC_MEMSTART and hence overrides it.
918 919 920 921 922 923 924 925 926

	  One use is for the kexec on panic case where the recovery kernel
	  must live at a different physical address than the primary
	  kernel.

	  Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
	  it has been loaded at and the compile time physical addresses
	  CONFIG_PHYSICAL_START is ignored.  However CONFIG_PHYSICAL_START
	  setting can still be useful to bootwrappers that need to know the
927 928 929 930 931
	  load address of the kernel (eg. u-boot/mkimage).

config RELOCATABLE_PPC32
	def_bool y
	depends on PPC32 && RELOCATABLE
932 933 934 935 936 937 938 939 940 941 942 943 944 945 946

config PAGE_OFFSET_BOOL
	bool "Set custom page offset address"
	depends on ADVANCED_OPTIONS
	help
	  This option allows you to set the kernel virtual address at which
	  the kernel will map low memory.  This can be useful in optimizing
	  the virtual memory layout of the system.

	  Say N here unless you know what you are doing.

config PAGE_OFFSET
	hex "Virtual address of memory base" if PAGE_OFFSET_BOOL
	default "0xc0000000"

947 948 949 950 951
config KERNEL_START_BOOL
	bool "Set custom kernel base address"
	depends on ADVANCED_OPTIONS
	help
	  This option allows you to set the kernel virtual address at which
952 953 954
	  the kernel will be loaded.  Normally this should match PAGE_OFFSET
	  however there are times (like kdump) that one might not want them
	  to be the same.
955 956 957 958 959

	  Say N here unless you know what you are doing.

config KERNEL_START
	hex "Virtual address of kernel base" if KERNEL_START_BOOL
960
	default PAGE_OFFSET if PAGE_OFFSET_BOOL
961
	default "0xc2000000" if CRASH_DUMP && !NONSTATIC_KERNEL
962 963
	default "0xc0000000"

964 965 966 967 968 969 970 971 972 973
config PHYSICAL_START_BOOL
	bool "Set physical address where the kernel is loaded"
	depends on ADVANCED_OPTIONS && FLATMEM && FSL_BOOKE
	help
	  This gives the physical address where the kernel is loaded.

	  Say N here unless you know what you are doing.

config PHYSICAL_START
	hex "Physical address where the kernel is loaded" if PHYSICAL_START_BOOL
974
	default "0x02000000" if PPC_STD_MMU && CRASH_DUMP && !NONSTATIC_KERNEL
975 976 977 978
	default "0x00000000"

config PHYSICAL_ALIGN
	hex
979
	default "0x04000000" if FSL_BOOKE
980 981 982 983 984
	help
	  This value puts the alignment restrictions on physical address
	  where kernel is loaded and run from. Kernel is compiled for an
	  address which meets above alignment restriction.

985 986 987 988 989 990 991 992 993 994 995 996
config TASK_SIZE_BOOL
	bool "Set custom user task size"
	depends on ADVANCED_OPTIONS
	help
	  This option allows you to set the amount of virtual address space
	  allocated to user tasks.  This can be useful in optimizing the
	  virtual memory layout of the system.

	  Say N here unless you know what you are doing.

config TASK_SIZE
	hex "Size of user task space" if TASK_SIZE_BOOL
P
Paul Bolle 已提交
997
	default "0x80000000" if PPC_8xx
998
	default "0xc0000000"
999

1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011
config CONSISTENT_SIZE_BOOL
	bool "Set custom consistent memory pool size"
	depends on ADVANCED_OPTIONS && NOT_COHERENT_CACHE
	help
	  This option allows you to set the size of the
	  consistent memory pool.  This pool of virtual memory
	  is used to make consistent memory allocations.

config CONSISTENT_SIZE
	hex "Size of consistent memory pool" if CONSISTENT_SIZE_BOOL
	default "0x00200000" if NOT_COHERENT_CACHE

1012 1013 1014 1015 1016
config PIN_TLB
	bool "Pinned Kernel TLBs (860 ONLY)"
	depends on ADVANCED_OPTIONS && 8xx
endmenu

S
Stephen Rothwell 已提交
1017
if PPC64
1018 1019
config RELOCATABLE
	bool "Build a relocatable kernel"
1020
	depends on !COMPILE_TEST
1021
	select NONSTATIC_KERNEL
1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032
	help
	  This builds a kernel image that is capable of running anywhere
	  in the RMA (real memory area) at any 16k-aligned base address.
	  The kernel is linked as a position-independent executable (PIE)
	  and contains dynamic relocations which are processed early
	  in the bootup process.

	  One use is for the kexec on panic case where the recovery kernel
	  must live at a different physical address than the primary
	  kernel.

1033
# This value must have zeroes in the bottom 60 bits otherwise lots will break
1034 1035 1036
config PAGE_OFFSET
	hex
	default "0xc000000000000000"
S
Stephen Rothwell 已提交
1037 1038
config KERNEL_START
	hex
S
Stephen Rothwell 已提交
1039
	default "0xc000000000000000"
1040 1041 1042
config PHYSICAL_START
	hex
	default "0x00000000"
S
Stephen Rothwell 已提交
1043 1044
endif

1045 1046 1047
config	ARCH_RANDOM
	def_bool n

1048 1049 1050 1051 1052 1053
source "net/Kconfig"

source "drivers/Kconfig"

source "fs/Kconfig"

1054 1055
source "arch/powerpc/sysdev/qe_lib/Kconfig"

1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067
source "lib/Kconfig"

source "arch/powerpc/Kconfig.debug"

source "security/Kconfig"

config KEYS_COMPAT
	bool
	depends on COMPAT && KEYS
	default y

source "crypto/Kconfig"
1068

1069 1070 1071
config PPC_LIB_RHEAP
	bool

1072
source "arch/powerpc/kvm/Kconfig"