rk356x.dtsi

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
 */

#include <dt-bindings/clock/rk3568-cru.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/phy/phy.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/power/rk3568-power.h>
#include <dt-bindings/soc/rockchip,boot-mode.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&gic>;
	#address-cells = <2>;
	#size-cells = <2>;

	aliases {
		gpio0 = &gpio0;
		gpio1 = &gpio1;
		gpio2 = &gpio2;
		gpio3 = &gpio3;
		gpio4 = &gpio4;
		i2c0 = &i2c0;
		i2c1 = &i2c1;
		i2c2 = &i2c2;
		i2c3 = &i2c3;
		i2c4 = &i2c4;
		i2c5 = &i2c5;
		serial0 = &uart0;
		serial1 = &uart1;
		serial2 = &uart2;
		serial3 = &uart3;
		serial4 = &uart4;
		serial5 = &uart5;
		serial6 = &uart6;
		serial7 = &uart7;
		serial8 = &uart8;
		serial9 = &uart9;
		spi0 = &spi0;
		spi1 = &spi1;
		spi2 = &spi2;
		spi3 = &spi3;
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		cpu0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x0>;
			clocks = <&scmi_clk 0>;
			#cooling-cells = <2>;
			enable-method = "psci";
			operating-points-v2 = <&cpu0_opp_table>;
		};

		cpu1: cpu@100 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x100>;
			#cooling-cells = <2>;
			enable-method = "psci";
			operating-points-v2 = <&cpu0_opp_table>;
		};

		cpu2: cpu@200 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x200>;
			#cooling-cells = <2>;
			enable-method = "psci";
			operating-points-v2 = <&cpu0_opp_table>;
		};

		cpu3: cpu@300 {
			device_type = "cpu";
			compatible = "arm,cortex-a55";
			reg = <0x0 0x300>;
			#cooling-cells = <2>;
			enable-method = "psci";
			operating-points-v2 = <&cpu0_opp_table>;
		};
	};

	cpu0_opp_table: opp-table-0 {
		compatible = "operating-points-v2";
		opp-shared;

		opp-408000000 {
			opp-hz = /bits/ 64 <408000000>;
			opp-microvolt = <900000 900000 1150000>;
			clock-latency-ns = <40000>;
		};

		opp-600000000 {
			opp-hz = /bits/ 64 <600000000>;
			opp-microvolt = <900000 900000 1150000>;
		};

		opp-816000000 {
			opp-hz = /bits/ 64 <816000000>;
			opp-microvolt = <900000 900000 1150000>;
			opp-suspend;
		};

		opp-1104000000 {
			opp-hz = /bits/ 64 <1104000000>;
			opp-microvolt = <900000 900000 1150000>;
		};

		opp-1416000000 {
			opp-hz = /bits/ 64 <1416000000>;
			opp-microvolt = <900000 900000 1150000>;
		};

		opp-1608000000 {
			opp-hz = /bits/ 64 <1608000000>;
			opp-microvolt = <975000 975000 1150000>;
		};

		opp-1800000000 {
			opp-hz = /bits/ 64 <1800000000>;
			opp-microvolt = <1050000 1050000 1150000>;
		};
	};

	firmware {
		scmi: scmi {
			compatible = "arm,scmi-smc";
			arm,smc-id = <0x82000010>;
			shmem = <&scmi_shmem>;
			#address-cells = <1>;
			#size-cells = <0>;

			scmi_clk: protocol@14 {
				reg = <0x14>;
				#clock-cells = <1>;
			};
		};
	};

	pmu {
		compatible = "arm,cortex-a55-pmu";
		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
		arm,no-tick-in-suspend;
	};

	xin24m: xin24m {
		compatible = "fixed-clock";
		clock-frequency = <24000000>;
		clock-output-names = "xin24m";
		#clock-cells = <0>;
	};

	xin32k: xin32k {
		compatible = "fixed-clock";
		clock-frequency = <32768>;
		clock-output-names = "xin32k";
		pinctrl-0 = <&clk32k_out0>;
		pinctrl-names = "default";
		#clock-cells = <0>;
	};

	sram@10f000 {
		compatible = "mmio-sram";
		reg = <0x0 0x0010f000 0x0 0x100>;
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0 0x0 0x0010f000 0x100>;

		scmi_shmem: sram@0 {
			compatible = "arm,scmi-shmem";
			reg = <0x0 0x100>;
		};
	};

	gic: interrupt-controller@fd400000 {
		compatible = "arm,gic-v3";
		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
		      <0x0 0xfd460000 0 0x80000>; /* GICR */
		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-controller;
		#interrupt-cells = <3>;
		mbi-alias = <0x0 0xfd410000>;
		mbi-ranges = <296 24>;
		msi-controller;
	};

	usb_host0_ehci: usb@fd800000 {
		compatible = "generic-ehci";
		reg = <0x0 0xfd800000 0x0 0x40000>;
		interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_USB2HOST0>, <&cru HCLK_USB2HOST0_ARB>,
			 <&cru PCLK_USB>;
		phys = <&u2phy1_otg>;
		phy-names = "usb";
		status = "disabled";
	};

	usb_host0_ohci: usb@fd840000 {
		compatible = "generic-ohci";
		reg = <0x0 0xfd840000 0x0 0x40000>;
		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_USB2HOST0>, <&cru HCLK_USB2HOST0_ARB>,
			 <&cru PCLK_USB>;
		phys = <&u2phy1_otg>;
		phy-names = "usb";
		status = "disabled";
	};

	usb_host1_ehci: usb@fd880000 {
		compatible = "generic-ehci";
		reg = <0x0 0xfd880000 0x0 0x40000>;
		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_USB2HOST1>, <&cru HCLK_USB2HOST1_ARB>,
			 <&cru PCLK_USB>;
		phys = <&u2phy1_host>;
		phy-names = "usb";
		status = "disabled";
	};

	usb_host1_ohci: usb@fd8c0000 {
		compatible = "generic-ohci";
		reg = <0x0 0xfd8c0000 0x0 0x40000>;
		interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_USB2HOST1>, <&cru HCLK_USB2HOST1_ARB>,
			 <&cru PCLK_USB>;
		phys = <&u2phy1_host>;
		phy-names = "usb";
		status = "disabled";
	};

	pmugrf: syscon@fdc20000 {
		compatible = "rockchip,rk3568-pmugrf", "syscon", "simple-mfd";
		reg = <0x0 0xfdc20000 0x0 0x10000>;

		pmu_io_domains: io-domains {
			compatible = "rockchip,rk3568-pmu-io-voltage-domain";
			status = "disabled";
		};
	};

	grf: syscon@fdc60000 {
		compatible = "rockchip,rk3568-grf", "syscon", "simple-mfd";
		reg = <0x0 0xfdc60000 0x0 0x10000>;
	};

	usb2phy0_grf: syscon@fdca0000 {
		compatible = "rockchip,rk3568-usb2phy-grf", "syscon";
		reg = <0x0 0xfdca0000 0x0 0x8000>;
	};

	usb2phy1_grf: syscon@fdca8000 {
		compatible = "rockchip,rk3568-usb2phy-grf", "syscon";
		reg = <0x0 0xfdca8000 0x0 0x8000>;
	};

	pmucru: clock-controller@fdd00000 {
		compatible = "rockchip,rk3568-pmucru";
		reg = <0x0 0xfdd00000 0x0 0x1000>;
		#clock-cells = <1>;
		#reset-cells = <1>;
	};

	cru: clock-controller@fdd20000 {
		compatible = "rockchip,rk3568-cru";
		reg = <0x0 0xfdd20000 0x0 0x1000>;
		#clock-cells = <1>;
		#reset-cells = <1>;
		assigned-clocks = <&cru PLL_GPLL>, <&pmucru PLL_PPLL>;
		assigned-clock-rates = <1200000000>, <200000000>;
		rockchip,grf = <&grf>;
	};

	i2c0: i2c@fdd40000 {
		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
		reg = <0x0 0xfdd40000 0x0 0x1000>;
		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
		clock-names = "i2c", "pclk";
		pinctrl-0 = <&i2c0_xfer>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	uart0: serial@fdd50000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfdd50000 0x0 0x100>;
		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&pmucru SCLK_UART0>, <&pmucru PCLK_UART0>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 0>, <&dmac0 1>;
		pinctrl-0 = <&uart0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	pwm0: pwm@fdd70000 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfdd70000 0x0 0x10>;
		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm0m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm1: pwm@fdd70010 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfdd70010 0x0 0x10>;
		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm1m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm2: pwm@fdd70020 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfdd70020 0x0 0x10>;
		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm2m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm3: pwm@fdd70030 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfdd70030 0x0 0x10>;
		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm3_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pmu: power-management@fdd90000 {
		compatible = "rockchip,rk3568-pmu", "syscon", "simple-mfd";
		reg = <0x0 0xfdd90000 0x0 0x1000>;

		power: power-controller {
			compatible = "rockchip,rk3568-power-controller";
			#power-domain-cells = <1>;
			#address-cells = <1>;
			#size-cells = <0>;

			/* These power domains are grouped by VD_GPU */
			power-domain@RK3568_PD_GPU {
				reg = <RK3568_PD_GPU>;
				clocks = <&cru ACLK_GPU_PRE>,
					 <&cru PCLK_GPU_PRE>;
				pm_qos = <&qos_gpu>;
				#power-domain-cells = <0>;
			};

			/* These power domains are grouped by VD_LOGIC */
			power-domain@RK3568_PD_VI {
				reg = <RK3568_PD_VI>;
				clocks = <&cru HCLK_VI>,
					 <&cru PCLK_VI>;
				pm_qos = <&qos_isp>,
					 <&qos_vicap0>,
					 <&qos_vicap1>;
				#power-domain-cells = <0>;
			};

			power-domain@RK3568_PD_VO {
				reg = <RK3568_PD_VO>;
				clocks = <&cru HCLK_VO>,
					 <&cru PCLK_VO>,
					 <&cru ACLK_VOP_PRE>;
				pm_qos = <&qos_hdcp>,
					 <&qos_vop_m0>,
					 <&qos_vop_m1>;
				#power-domain-cells = <0>;
			};

			power-domain@RK3568_PD_RGA {
				reg = <RK3568_PD_RGA>;
				clocks = <&cru HCLK_RGA_PRE>,
					 <&cru PCLK_RGA_PRE>;
				pm_qos = <&qos_ebc>,
					 <&qos_iep>,
					 <&qos_jpeg_dec>,
					 <&qos_jpeg_enc>,
					 <&qos_rga_rd>,
					 <&qos_rga_wr>;
				#power-domain-cells = <0>;
			};

			power-domain@RK3568_PD_VPU {
				reg = <RK3568_PD_VPU>;
				clocks = <&cru HCLK_VPU_PRE>;
				pm_qos = <&qos_vpu>;
				#power-domain-cells = <0>;
			};

			power-domain@RK3568_PD_RKVDEC {
				clocks = <&cru HCLK_RKVDEC_PRE>;
				reg = <RK3568_PD_RKVDEC>;
				pm_qos = <&qos_rkvdec>;
				#power-domain-cells = <0>;
			};

			power-domain@RK3568_PD_RKVENC {
				reg = <RK3568_PD_RKVENC>;
				clocks = <&cru HCLK_RKVENC_PRE>;
				pm_qos = <&qos_rkvenc_rd_m0>,
					 <&qos_rkvenc_rd_m1>,
					 <&qos_rkvenc_wr_m0>;
				#power-domain-cells = <0>;
			};
		};
	};

	sdmmc2: mmc@fe000000 {
		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0x0 0xfe000000 0x0 0x4000>;
		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_SDMMC2>, <&cru CLK_SDMMC2>,
			 <&cru SCLK_SDMMC2_DRV>, <&cru SCLK_SDMMC2_SAMPLE>;
		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
		fifo-depth = <0x100>;
		max-frequency = <150000000>;
		resets = <&cru SRST_SDMMC2>;
		reset-names = "reset";
		status = "disabled";
	};

	gmac1: ethernet@fe010000 {
		compatible = "rockchip,rk3568-gmac", "snps,dwmac-4.20a";
		reg = <0x0 0xfe010000 0x0 0x10000>;
		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "macirq", "eth_wake_irq";
		clocks = <&cru SCLK_GMAC1>, <&cru SCLK_GMAC1_RX_TX>,
			 <&cru SCLK_GMAC1_RX_TX>, <&cru CLK_MAC1_REFOUT>,
			 <&cru ACLK_GMAC1>, <&cru PCLK_GMAC1>,
			 <&cru SCLK_GMAC1_RX_TX>, <&cru CLK_GMAC1_PTP_REF>;
		clock-names = "stmmaceth", "mac_clk_rx",
			      "mac_clk_tx", "clk_mac_refout",
			      "aclk_mac", "pclk_mac",
			      "clk_mac_speed", "ptp_ref";
		resets = <&cru SRST_A_GMAC1>;
		reset-names = "stmmaceth";
		rockchip,grf = <&grf>;
		snps,axi-config = <&gmac1_stmmac_axi_setup>;
		snps,mixed-burst;
		snps,mtl-rx-config = <&gmac1_mtl_rx_setup>;
		snps,mtl-tx-config = <&gmac1_mtl_tx_setup>;
		snps,tso;
		status = "disabled";

		mdio1: mdio {
			compatible = "snps,dwmac-mdio";
			#address-cells = <0x1>;
			#size-cells = <0x0>;
		};

		gmac1_stmmac_axi_setup: stmmac-axi-config {
			snps,blen = <0 0 0 0 16 8 4>;
			snps,rd_osr_lmt = <8>;
			snps,wr_osr_lmt = <4>;
		};

		gmac1_mtl_rx_setup: rx-queues-config {
			snps,rx-queues-to-use = <1>;
			queue0 {};
		};

		gmac1_mtl_tx_setup: tx-queues-config {
			snps,tx-queues-to-use = <1>;
			queue0 {};
		};
	};

	qos_gpu: qos@fe128000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe128000 0x0 0x20>;
	};

	qos_rkvenc_rd_m0: qos@fe138080 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe138080 0x0 0x20>;
	};

	qos_rkvenc_rd_m1: qos@fe138100 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe138100 0x0 0x20>;
	};

	qos_rkvenc_wr_m0: qos@fe138180 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe138180 0x0 0x20>;
	};

	qos_isp: qos@fe148000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe148000 0x0 0x20>;
	};

	qos_vicap0: qos@fe148080 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe148080 0x0 0x20>;
	};

	qos_vicap1: qos@fe148100 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe148100 0x0 0x20>;
	};

	qos_vpu: qos@fe150000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe150000 0x0 0x20>;
	};

	qos_ebc: qos@fe158000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe158000 0x0 0x20>;
	};

	qos_iep: qos@fe158100 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe158100 0x0 0x20>;
	};

	qos_jpeg_dec: qos@fe158180 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe158180 0x0 0x20>;
	};

	qos_jpeg_enc: qos@fe158200 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe158200 0x0 0x20>;
	};

	qos_rga_rd: qos@fe158280 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe158280 0x0 0x20>;
	};

	qos_rga_wr: qos@fe158300 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe158300 0x0 0x20>;
	};

	qos_npu: qos@fe180000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe180000 0x0 0x20>;
	};

	qos_pcie2x1: qos@fe190000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe190000 0x0 0x20>;
	};

	qos_sata1: qos@fe190280 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe190280 0x0 0x20>;
	};

	qos_sata2: qos@fe190300 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe190300 0x0 0x20>;
	};

	qos_usb3_0: qos@fe190380 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe190380 0x0 0x20>;
	};

	qos_usb3_1: qos@fe190400 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe190400 0x0 0x20>;
	};

	qos_rkvdec: qos@fe198000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe198000 0x0 0x20>;
	};

	qos_hdcp: qos@fe1a8000 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe1a8000 0x0 0x20>;
	};

	qos_vop_m0: qos@fe1a8080 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe1a8080 0x0 0x20>;
	};

	qos_vop_m1: qos@fe1a8100 {
		compatible = "rockchip,rk3568-qos", "syscon";
		reg = <0x0 0xfe1a8100 0x0 0x20>;
	};

	sdmmc0: mmc@fe2b0000 {
		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0x0 0xfe2b0000 0x0 0x4000>;
		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_SDMMC0>, <&cru CLK_SDMMC0>,
			 <&cru SCLK_SDMMC0_DRV>, <&cru SCLK_SDMMC0_SAMPLE>;
		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
		fifo-depth = <0x100>;
		max-frequency = <150000000>;
		resets = <&cru SRST_SDMMC0>;
		reset-names = "reset";
		status = "disabled";
	};

	sdmmc1: mmc@fe2c0000 {
		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
		reg = <0x0 0xfe2c0000 0x0 0x4000>;
		interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru HCLK_SDMMC1>, <&cru CLK_SDMMC1>,
			 <&cru SCLK_SDMMC1_DRV>, <&cru SCLK_SDMMC1_SAMPLE>;
		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
		fifo-depth = <0x100>;
		max-frequency = <150000000>;
		resets = <&cru SRST_SDMMC1>;
		reset-names = "reset";
		status = "disabled";
	};

	sdhci: mmc@fe310000 {
		compatible = "rockchip,rk3568-dwcmshc";
		reg = <0x0 0xfe310000 0x0 0x10000>;
		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
		assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>;
		assigned-clock-rates = <200000000>, <24000000>;
		clocks = <&cru CCLK_EMMC>, <&cru HCLK_EMMC>,
			 <&cru ACLK_EMMC>, <&cru BCLK_EMMC>,
			 <&cru TCLK_EMMC>;
		clock-names = "core", "bus", "axi", "block", "timer";
		status = "disabled";
	};

	spdif: spdif@fe460000 {
		compatible = "rockchip,rk3568-spdif";
		reg = <0x0 0xfe460000 0x0 0x1000>;
		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
		clock-names = "mclk", "hclk";
		clocks = <&cru MCLK_SPDIF_8CH>, <&cru HCLK_SPDIF_8CH>;
		dmas = <&dmac1 1>;
		dma-names = "tx";
		pinctrl-names = "default";
		pinctrl-0 = <&spdifm0_tx>;
		#sound-dai-cells = <0>;
		status = "disabled";
	};

	i2s1_8ch: i2s@fe410000 {
		compatible = "rockchip,rk3568-i2s-tdm";
		reg = <0x0 0xfe410000 0x0 0x1000>;
		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
		assigned-clocks = <&cru CLK_I2S1_8CH_TX_SRC>, <&cru CLK_I2S1_8CH_RX_SRC>;
		assigned-clock-rates = <1188000000>, <1188000000>;
		clocks = <&cru MCLK_I2S1_8CH_TX>, <&cru MCLK_I2S1_8CH_RX>,
			 <&cru HCLK_I2S1_8CH>;
		clock-names = "mclk_tx", "mclk_rx", "hclk";
		dmas = <&dmac1 3>, <&dmac1 2>;
		dma-names = "rx", "tx";
		resets = <&cru SRST_M_I2S1_8CH_TX>, <&cru SRST_M_I2S1_8CH_RX>;
		reset-names = "tx-m", "rx-m";
		rockchip,grf = <&grf>;
		pinctrl-names = "default";
		pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_sclkrx
			     &i2s1m0_lrcktx &i2s1m0_lrckrx
			     &i2s1m0_sdi0   &i2s1m0_sdi1
			     &i2s1m0_sdi2   &i2s1m0_sdi3
			     &i2s1m0_sdo0   &i2s1m0_sdo1
			     &i2s1m0_sdo2   &i2s1m0_sdo3>;
		#sound-dai-cells = <0>;
		status = "disabled";
	};

	i2s3_2ch: i2s@fe430000 {
		compatible = "rockchip,rk3568-i2s-tdm";
		reg = <0x0 0xfe430000 0x0 0x1000>;
		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru MCLK_I2S3_2CH_TX>, <&cru MCLK_I2S3_2CH_RX>,
			 <&cru HCLK_I2S3_2CH>;
		clock-names = "mclk_tx", "mclk_rx", "hclk";
		dmas = <&dmac1 6>, <&dmac1 7>;
		dma-names = "tx", "rx";
		resets = <&cru SRST_M_I2S3_2CH_TX>, <&cru SRST_M_I2S3_2CH_RX>;
		reset-names = "tx-m", "rx-m";
		rockchip,grf = <&grf>;
		#sound-dai-cells = <0>;
		status = "disabled";
	};

	dmac0: dmac@fe530000 {
		compatible = "arm,pl330", "arm,primecell";
		reg = <0x0 0xfe530000 0x0 0x4000>;
		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
		arm,pl330-periph-burst;
		clocks = <&cru ACLK_BUS>;
		clock-names = "apb_pclk";
		#dma-cells = <1>;
	};

	dmac1: dmac@fe550000 {
		compatible = "arm,pl330", "arm,primecell";
		reg = <0x0 0xfe550000 0x0 0x4000>;
		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
		arm,pl330-periph-burst;
		clocks = <&cru ACLK_BUS>;
		clock-names = "apb_pclk";
		#dma-cells = <1>;
	};

	i2c1: i2c@fe5a0000 {
		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
		reg = <0x0 0xfe5a0000 0x0 0x1000>;
		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_I2C1>, <&cru PCLK_I2C1>;
		clock-names = "i2c", "pclk";
		pinctrl-0 = <&i2c1_xfer>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	i2c2: i2c@fe5b0000 {
		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
		reg = <0x0 0xfe5b0000 0x0 0x1000>;
		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_I2C2>, <&cru PCLK_I2C2>;
		clock-names = "i2c", "pclk";
		pinctrl-0 = <&i2c2m0_xfer>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	i2c3: i2c@fe5c0000 {
		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
		reg = <0x0 0xfe5c0000 0x0 0x1000>;
		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_I2C3>, <&cru PCLK_I2C3>;
		clock-names = "i2c", "pclk";
		pinctrl-0 = <&i2c3m0_xfer>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	i2c4: i2c@fe5d0000 {
		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
		reg = <0x0 0xfe5d0000 0x0 0x1000>;
		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_I2C4>, <&cru PCLK_I2C4>;
		clock-names = "i2c", "pclk";
		pinctrl-0 = <&i2c4m0_xfer>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	i2c5: i2c@fe5e0000 {
		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
		reg = <0x0 0xfe5e0000 0x0 0x1000>;
		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_I2C5>, <&cru PCLK_I2C5>;
		clock-names = "i2c", "pclk";
		pinctrl-0 = <&i2c5m0_xfer>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	wdt: watchdog@fe600000 {
		compatible = "rockchip,rk3568-wdt", "snps,dw-wdt";
		reg = <0x0 0xfe600000 0x0 0x100>;
		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru TCLK_WDT_NS>, <&cru PCLK_WDT_NS>;
		clock-names = "tclk", "pclk";
	};

	spi0: spi@fe610000 {
		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
		reg = <0x0 0xfe610000 0x0 0x1000>;
		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_SPI0>, <&cru PCLK_SPI0>;
		clock-names = "spiclk", "apb_pclk";
		dmas = <&dmac0 20>, <&dmac0 21>;
		dma-names = "tx", "rx";
		pinctrl-names = "default";
		pinctrl-0 = <&spi0m0_cs0 &spi0m0_cs1 &spi0m0_pins>;
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	spi1: spi@fe620000 {
		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
		reg = <0x0 0xfe620000 0x0 0x1000>;
		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_SPI1>, <&cru PCLK_SPI1>;
		clock-names = "spiclk", "apb_pclk";
		dmas = <&dmac0 22>, <&dmac0 23>;
		dma-names = "tx", "rx";
		pinctrl-names = "default";
		pinctrl-0 = <&spi1m0_cs0 &spi1m0_cs1 &spi1m0_pins>;
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	spi2: spi@fe630000 {
		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
		reg = <0x0 0xfe630000 0x0 0x1000>;
		interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_SPI2>, <&cru PCLK_SPI2>;
		clock-names = "spiclk", "apb_pclk";
		dmas = <&dmac0 24>, <&dmac0 25>;
		dma-names = "tx", "rx";
		pinctrl-names = "default";
		pinctrl-0 = <&spi2m0_cs0 &spi2m0_cs1 &spi2m0_pins>;
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	spi3: spi@fe640000 {
		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
		reg = <0x0 0xfe640000 0x0 0x1000>;
		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_SPI3>, <&cru PCLK_SPI3>;
		clock-names = "spiclk", "apb_pclk";
		dmas = <&dmac0 26>, <&dmac0 27>;
		dma-names = "tx", "rx";
		pinctrl-names = "default";
		pinctrl-0 = <&spi3m0_cs0 &spi3m0_cs1 &spi3m0_pins>;
		#address-cells = <1>;
		#size-cells = <0>;
		status = "disabled";
	};

	uart1: serial@fe650000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe650000 0x0 0x100>;
		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 2>, <&dmac0 3>;
		pinctrl-0 = <&uart1m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart2: serial@fe660000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe660000 0x0 0x100>;
		interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 4>, <&dmac0 5>;
		pinctrl-0 = <&uart2m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart3: serial@fe670000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe670000 0x0 0x100>;
		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 6>, <&dmac0 7>;
		pinctrl-0 = <&uart3m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart4: serial@fe680000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe680000 0x0 0x100>;
		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 8>, <&dmac0 9>;
		pinctrl-0 = <&uart4m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart5: serial@fe690000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe690000 0x0 0x100>;
		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 10>, <&dmac0 11>;
		pinctrl-0 = <&uart5m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart6: serial@fe6a0000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe6a0000 0x0 0x100>;
		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART6>, <&cru PCLK_UART6>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 12>, <&dmac0 13>;
		pinctrl-0 = <&uart6m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart7: serial@fe6b0000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe6b0000 0x0 0x100>;
		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART7>, <&cru PCLK_UART7>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 14>, <&dmac0 15>;
		pinctrl-0 = <&uart7m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart8: serial@fe6c0000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe6c0000 0x0 0x100>;
		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART8>, <&cru PCLK_UART8>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 16>, <&dmac0 17>;
		pinctrl-0 = <&uart8m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	uart9: serial@fe6d0000 {
		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
		reg = <0x0 0xfe6d0000 0x0 0x100>;
		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru SCLK_UART9>, <&cru PCLK_UART9>;
		clock-names = "baudclk", "apb_pclk";
		dmas = <&dmac0 18>, <&dmac0 19>;
		pinctrl-0 = <&uart9m0_xfer>;
		pinctrl-names = "default";
		reg-io-width = <4>;
		reg-shift = <2>;
		status = "disabled";
	};

	thermal_zones: thermal-zones {
		cpu_thermal: cpu-thermal {
			polling-delay-passive = <100>;
			polling-delay = <1000>;

			thermal-sensors = <&tsadc 0>;

			trips {
				cpu_alert0: cpu_alert0 {
					temperature = <70000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_alert1: cpu_alert1 {
					temperature = <75000>;
					hysteresis = <2000>;
					type = "passive";
				};
				cpu_crit: cpu_crit {
					temperature = <95000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};

			cooling-maps {
				map0 {
					trip = <&cpu_alert0>;
					cooling-device =
						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
				};
			};
		};

		gpu_thermal: gpu-thermal {
			polling-delay-passive = <20>; /* milliseconds */
			polling-delay = <1000>; /* milliseconds */

			thermal-sensors = <&tsadc 1>;
		};
	};

	tsadc: tsadc@fe710000 {
		compatible = "rockchip,rk3568-tsadc";
		reg = <0x0 0xfe710000 0x0 0x100>;
		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
		assigned-clocks = <&cru CLK_TSADC_TSEN>, <&cru CLK_TSADC>;
		assigned-clock-rates = <17000000>, <700000>;
		clocks = <&cru CLK_TSADC>, <&cru PCLK_TSADC>;
		clock-names = "tsadc", "apb_pclk";
		resets = <&cru SRST_P_TSADC>, <&cru SRST_TSADC>,
			 <&cru SRST_TSADCPHY>;
		rockchip,grf = <&grf>;
		rockchip,hw-tshut-temp = <95000>;
		pinctrl-names = "init", "default", "sleep";
		pinctrl-0 = <&tsadc_pin>;
		pinctrl-1 = <&tsadc_shutorg>;
		pinctrl-2 = <&tsadc_pin>;
		#thermal-sensor-cells = <1>;
		status = "disabled";
	};

	saradc: saradc@fe720000 {
		compatible = "rockchip,rk3568-saradc", "rockchip,rk3399-saradc";
		reg = <0x0 0xfe720000 0x0 0x100>;
		interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
		clock-names = "saradc", "apb_pclk";
		resets = <&cru SRST_P_SARADC>;
		reset-names = "saradc-apb";
		#io-channel-cells = <1>;
		status = "disabled";
	};

	pwm4: pwm@fe6e0000 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6e0000 0x0 0x10>;
		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm4_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm5: pwm@fe6e0010 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6e0010 0x0 0x10>;
		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm5_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm6: pwm@fe6e0020 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6e0020 0x0 0x10>;
		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm6_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm7: pwm@fe6e0030 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6e0030 0x0 0x10>;
		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm7_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm8: pwm@fe6f0000 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6f0000 0x0 0x10>;
		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm8m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm9: pwm@fe6f0010 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6f0010 0x0 0x10>;
		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm9m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm10: pwm@fe6f0020 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6f0020 0x0 0x10>;
		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm10m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm11: pwm@fe6f0030 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe6f0030 0x0 0x10>;
		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm11m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm12: pwm@fe700000 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe700000 0x0 0x10>;
		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm12m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm13: pwm@fe700010 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe700010 0x0 0x10>;
		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm13m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm14: pwm@fe700020 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe700020 0x0 0x10>;
		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm14m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	pwm15: pwm@fe700030 {
		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
		reg = <0x0 0xfe700030 0x0 0x10>;
		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
		clock-names = "pwm", "pclk";
		pinctrl-0 = <&pwm15m0_pins>;
		pinctrl-names = "default";
		#pwm-cells = <3>;
		status = "disabled";
	};

	u2phy0: usb2phy@fe8a0000 {
		compatible = "rockchip,rk3568-usb2phy";
		reg = <0x0 0xfe8a0000 0x0 0x10000>;
		clocks = <&pmucru CLK_USBPHY0_REF>;
		clock-names = "phyclk";
		clock-output-names = "clk_usbphy0_480m";
		interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
		rockchip,usbgrf = <&usb2phy0_grf>;
		#clock-cells = <0>;
		status = "disabled";

		u2phy0_host: host-port {
			#phy-cells = <0>;
			status = "disabled";
		};

		u2phy0_otg: otg-port {
			#phy-cells = <0>;
			status = "disabled";
		};
	};

	u2phy1: usb2phy@fe8b0000 {
		compatible = "rockchip,rk3568-usb2phy";
		reg = <0x0 0xfe8b0000 0x0 0x10000>;
		clocks = <&pmucru CLK_USBPHY1_REF>;
		clock-names = "phyclk";
		clock-output-names = "clk_usbphy1_480m";
		interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
		rockchip,usbgrf = <&usb2phy1_grf>;
		#clock-cells = <0>;
		status = "disabled";

		u2phy1_host: host-port {
			#phy-cells = <0>;
			status = "disabled";
		};

		u2phy1_otg: otg-port {
			#phy-cells = <0>;
			status = "disabled";
		};
	};

	pinctrl: pinctrl {
		compatible = "rockchip,rk3568-pinctrl";
		rockchip,grf = <&grf>;
		rockchip,pmu = <&pmugrf>;
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		gpio0: gpio@fdd60000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x0 0xfdd60000 0x0 0x100>;
			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		gpio1: gpio@fe740000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x0 0xfe740000 0x0 0x100>;
			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		gpio2: gpio@fe750000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x0 0xfe750000 0x0 0x100>;
			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		gpio3: gpio@fe760000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x0 0xfe760000 0x0 0x100>;
			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		gpio4: gpio@fe770000 {
			compatible = "rockchip,gpio-bank";
			reg = <0x0 0xfe770000 0x0 0x100>;
			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};
};

#include "rk3568-pinctrl.dtsi"