superio.c 13.8 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4 5 6 7 8 9 10 11 12 13
/*      National Semiconductor NS87560UBD Super I/O controller used in
 *      HP [BCJ]x000 workstations.
 *
 *      This chip is a horrid piece of engineering, and National
 *      denies any knowledge of its existence. Thus no datasheet is
 *      available off www.national.com. 
 *
 *	(C) Copyright 2000 Linuxcare, Inc.
 * 	(C) Copyright 2000 Linuxcare Canada, Inc.
 *	(C) Copyright 2000 Martin K. Petersen <mkp@linuxcare.com>
 * 	(C) Copyright 2000 Alex deVries <alex@onefishtwo.ca>
 *      (C) Copyright 2001 John Marvin <jsm fc hp com>
 *      (C) Copyright 2003 Grant Grundler <grundler parisc-linux org>
14
 *	(C) Copyright 2005 Kyle McMartin <kyle@parisc-linux.org>
15
 *	(C) Copyright 2006 Helge Deller <deller@gmx.de>
L
Linus Torvalds 已提交
16 17 18 19 20 21 22 23 24 25 26 27
 *
 *	This program is free software; you can redistribute it and/or
 *	modify it under the terms of the GNU General Public License as
 *	published by the Free Software Foundation; either version 2 of
 *	the License, or (at your option) any later version.  
 *
 *	The initial version of this is by Martin Peterson.  Alex deVries
 *	has spent a bit of time trying to coax it into working.
 *
 *      Major changes to get basic interrupt infrastructure working to
 *      hopefully be able to support all SuperIO devices. Currently
 *      works with serial. -- John Marvin <jsm@fc.hp.com>
28 29 30
 *
 *	Converted superio_init() to be a PCI_FIXUP_FINAL callee.
 *         -- Kyle McMartin <kyle@parisc-linux.org>
L
Linus Torvalds 已提交
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
 */


/* NOTES:
 * 
 * Function 0 is an IDE controller. It is identical to a PC87415 IDE
 * controller (and identifies itself as such).
 *
 * Function 1 is a "Legacy I/O" controller. Under this function is a
 * whole mess of legacy I/O peripherals. Of course, HP hasn't enabled
 * all the functionality in hardware, but the following is available:
 *
 *      Two 16550A compatible serial controllers
 *      An IEEE 1284 compatible parallel port
 *      A floppy disk controller
 *
 * Function 2 is a USB controller.
 *
 * We must be incredibly careful during initialization.  Since all
 * interrupts are routed through function 1 (which is not allowed by
 * the PCI spec), we need to program the PICs on the legacy I/O port
 * *before* we attempt to set up IDE and USB.  @#$!&
 *
 * According to HP, devices are only enabled by firmware if they have
 * a physical device connected.
 *
 * Configuration register bits:
 *     0x5A: FDC, SP1, IDE1, SP2, IDE2, PAR, Reserved, P92
 *     0x5B: RTC, 8259, 8254, DMA1, DMA2, KBC, P61, APM
 *
 */

#include <linux/errno.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/serial.h>
#include <linux/pci.h>
#include <linux/parport.h>
#include <linux/parport_pc.h>
#include <linux/termios.h>
#include <linux/tty.h>
#include <linux/serial_core.h>
76
#include <linux/serial_8250.h>
L
Linus Torvalds 已提交
77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93
#include <linux/delay.h>

#include <asm/io.h>
#include <asm/hardware.h>
#include <asm/superio.h>

static struct superio_device sio_dev;


#undef DEBUG_SUPERIO_INIT

#ifdef DEBUG_SUPERIO_INIT
#define DBG_INIT(x...)  printk(x)
#else
#define DBG_INIT(x...)
#endif

94 95 96
#define SUPERIO	"SuperIO"
#define PFX	SUPERIO ": "

L
Linus Torvalds 已提交
97
static irqreturn_t
98
superio_interrupt(int parent_irq, void *devp)
L
Linus Torvalds 已提交
99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124
{
	u8 results;
	u8 local_irq;

	/* Poll the 8259 to see if there's an interrupt. */
	outb (OCW3_POLL,IC_PIC1+0);

	results = inb(IC_PIC1+0);

	/*
	 * Bit    7:	1 = active Interrupt; 0 = no Interrupt pending
	 * Bits 6-3:	zero
	 * Bits 2-0:	highest priority, active requesting interrupt ID (0-7)
	 */
	if ((results & 0x80) == 0) {
		/* I suspect "spurious" interrupts are from unmasking an IRQ.
		 * We don't know if an interrupt was/is pending and thus
		 * just call the handler for that IRQ as if it were pending.
		 */
		return IRQ_NONE;
	}

	/* Check to see which device is interrupting */
	local_irq = results & 0x0f;

	if (local_irq == 2 || local_irq > 7) {
125
		printk(KERN_ERR PFX "slave interrupted!\n");
L
Linus Torvalds 已提交
126 127 128 129 130 131 132 133 134 135
		return IRQ_HANDLED;
	}

	if (local_irq == 7) {

		/* Could be spurious. Check in service bits */

		outb(OCW3_ISR,IC_PIC1+0);
		results = inb(IC_PIC1+0);
		if ((results & 0x80) == 0) { /* if ISR7 not set: spurious */
136
			printk(KERN_WARNING PFX "spurious interrupt!\n");
L
Linus Torvalds 已提交
137 138 139 140 141
			return IRQ_HANDLED;
		}
	}

	/* Call the appropriate device's interrupt */
142
	generic_handle_irq(local_irq);
L
Linus Torvalds 已提交
143 144 145 146 147 148 149 150 151

	/* set EOI - forces a new interrupt if a lower priority device
	 * still needs service.
	 */
	outb((OCW2_SEOI|local_irq),IC_PIC1 + 0);
	return IRQ_HANDLED;
}

/* Initialize Super I/O device */
152 153
static void
superio_init(struct pci_dev *pcidev)
L
Linus Torvalds 已提交
154
{
155
	struct superio_device *sio = &sio_dev;
L
Linus Torvalds 已提交
156 157
	struct pci_dev *pdev = sio->lio_pdev;
	u16 word;
158
	int ret;
L
Linus Torvalds 已提交
159

H
Helge Deller 已提交
160
	if (sio->suckyio_irq_enabled)
L
Linus Torvalds 已提交
161 162
		return;

163 164
	BUG_ON(!pdev);
	BUG_ON(!sio->usb_pdev);
L
Linus Torvalds 已提交
165 166 167 168 169 170 171

	/* use the IRQ iosapic found for USB INT D... */
	pdev->irq = sio->usb_pdev->irq;

	/* ...then properly fixup the USB to point at suckyio PIC */
	sio->usb_pdev->irq = superio_fixup_irq(sio->usb_pdev);

172
	printk(KERN_INFO PFX "Found NS87560 Legacy I/O device at %s (IRQ %i)\n",
173
	       pci_name(pdev), pdev->irq);
L
Linus Torvalds 已提交
174 175 176

	pci_read_config_dword (pdev, SIO_SP1BAR, &sio->sp1_base);
	sio->sp1_base &= ~1;
177
	printk(KERN_INFO PFX "Serial port 1 at 0x%x\n", sio->sp1_base);
L
Linus Torvalds 已提交
178 179 180

	pci_read_config_dword (pdev, SIO_SP2BAR, &sio->sp2_base);
	sio->sp2_base &= ~1;
181
	printk(KERN_INFO PFX "Serial port 2 at 0x%x\n", sio->sp2_base);
L
Linus Torvalds 已提交
182 183 184

	pci_read_config_dword (pdev, SIO_PPBAR, &sio->pp_base);
	sio->pp_base &= ~1;
185
	printk(KERN_INFO PFX "Parallel port at 0x%x\n", sio->pp_base);
L
Linus Torvalds 已提交
186 187 188

	pci_read_config_dword (pdev, SIO_FDCBAR, &sio->fdc_base);
	sio->fdc_base &= ~1;
189
	printk(KERN_INFO PFX "Floppy controller at 0x%x\n", sio->fdc_base);
L
Linus Torvalds 已提交
190 191
	pci_read_config_dword (pdev, SIO_ACPIBAR, &sio->acpi_base);
	sio->acpi_base &= ~1;
192
	printk(KERN_INFO PFX "ACPI at 0x%x\n", sio->acpi_base);
L
Linus Torvalds 已提交
193 194 195 196 197 198

	request_region (IC_PIC1, 0x1f, "pic1");
	request_region (IC_PIC2, 0x1f, "pic2");
	request_region (sio->acpi_base, 0x1f, "acpi");

	/* Enable the legacy I/O function */
H
Helge Deller 已提交
199
	pci_read_config_word (pdev, PCI_COMMAND, &word);
L
Linus Torvalds 已提交
200 201 202 203
	word |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY | PCI_COMMAND_IO;
	pci_write_config_word (pdev, PCI_COMMAND, word);

	pci_set_master (pdev);
204 205
	ret = pci_enable_device(pdev);
	BUG_ON(ret < 0);	/* not too much we can do about this... */
L
Linus Torvalds 已提交
206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272

	/*
	 * Next project is programming the onboard interrupt controllers.
	 * PDC hasn't done this for us, since it's using polled I/O.
	 *
	 * XXX Use dword writes to avoid bugs in Elroy or Suckyio Config
	 *     space access.  PCI is by nature a 32-bit bus and config
	 *     space can be sensitive to that.
	 */

	/* 0x64 - 0x67 :
		DMA Rtg 2
		DMA Rtg 3
		DMA Chan Ctl
		TRIGGER_1    == 0x82   USB & IDE level triggered, rest to edge
	*/
	pci_write_config_dword (pdev, 0x64,         0x82000000U);

	/* 0x68 - 0x6b :
		TRIGGER_2    == 0x00   all edge triggered (not used)
		CFG_IR_SER   == 0x43   SerPort1 = IRQ3, SerPort2 = IRQ4
		CFG_IR_PF    == 0x65   ParPort  = IRQ5, FloppyCtlr = IRQ6
		CFG_IR_IDE   == 0x07   IDE1 = IRQ7, reserved
	*/
	pci_write_config_dword (pdev, TRIGGER_2,    0x07654300U);

	/* 0x6c - 0x6f :
		CFG_IR_INTAB == 0x00
		CFG_IR_INTCD == 0x10   USB = IRQ1
		CFG_IR_PS2   == 0x00
		CFG_IR_FXBUS == 0x00
	*/
	pci_write_config_dword (pdev, CFG_IR_INTAB, 0x00001000U);

	/* 0x70 - 0x73 :
		CFG_IR_USB   == 0x00  not used. USB is connected to INTD.
		CFG_IR_ACPI  == 0x00  not used.
		DMA Priority == 0x4c88  Power on default value. NFC.
	*/
	pci_write_config_dword (pdev, CFG_IR_USB, 0x4c880000U);

	/* PIC1 Initialization Command Word register programming */
	outb (0x11,IC_PIC1+0);	/* ICW1: ICW4 write req | ICW1 */
	outb (0x00,IC_PIC1+1);	/* ICW2: interrupt vector table - not used */
	outb (0x04,IC_PIC1+1);	/* ICW3: Cascade */
	outb (0x01,IC_PIC1+1);	/* ICW4: x86 mode */

	/* PIC1 Program Operational Control Words */
	outb (0xff,IC_PIC1+1);	/* OCW1: Mask all interrupts */
	outb (0xc2,IC_PIC1+0);  /* OCW2: priority (3-7,0-2) */

	/* PIC2 Initialization Command Word register programming */
	outb (0x11,IC_PIC2+0);	/* ICW1: ICW4 write req | ICW1 */
	outb (0x00,IC_PIC2+1);	/* ICW2: N/A */
	outb (0x02,IC_PIC2+1);	/* ICW3: Slave ID code */
	outb (0x01,IC_PIC2+1);	/* ICW4: x86 mode */
		
	/* Program Operational Control Words */
	outb (0xff,IC_PIC1+1);	/* OCW1: Mask all interrupts */
	outb (0x68,IC_PIC1+0);	/* OCW3: OCW3 select | ESMM | SMM */

	/* Write master mask reg */
	outb (0xff,IC_PIC1+1);

	/* Setup USB power regulation */
	outb(1, sio->acpi_base + USB_REG_CR);
	if (inb(sio->acpi_base + USB_REG_CR) & 1)
273
		printk(KERN_INFO PFX "USB regulator enabled\n");
L
Linus Torvalds 已提交
274
	else
275
		printk(KERN_ERR PFX "USB regulator not initialized!\n");
L
Linus Torvalds 已提交
276

P
Peter Zijlstra 已提交
277
	if (request_irq(pdev->irq, superio_interrupt, 0,
278
			SUPERIO, (void *)sio)) {
L
Linus Torvalds 已提交
279

280
		printk(KERN_ERR PFX "could not get irq\n");
L
Linus Torvalds 已提交
281 282 283 284 285 286
		BUG();
		return;
	}

	sio->suckyio_irq_enabled = 1;
}
287
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO, superio_init);
L
Linus Torvalds 已提交
288

289
static void superio_mask_irq(struct irq_data *d)
L
Linus Torvalds 已提交
290
{
291
	unsigned int irq = d->irq;
L
Linus Torvalds 已提交
292 293 294
	u8 r8;

	if ((irq < 1) || (irq == 2) || (irq > 7)) {
295
		printk(KERN_ERR PFX "Illegal irq number.\n");
L
Linus Torvalds 已提交
296 297 298 299 300 301 302 303 304 305 306
		BUG();
		return;
	}

	/* Mask interrupt */

	r8 = inb(IC_PIC1+1);
	r8 |= (1 << irq);
	outb (r8,IC_PIC1+1);
}

307
static void superio_unmask_irq(struct irq_data *d)
L
Linus Torvalds 已提交
308
{
309
	unsigned int irq = d->irq;
L
Linus Torvalds 已提交
310 311 312
	u8 r8;

	if ((irq < 1) || (irq == 2) || (irq > 7)) {
313
		printk(KERN_ERR PFX "Illegal irq number (%d).\n", irq);
L
Linus Torvalds 已提交
314 315 316 317 318 319 320 321 322 323
		BUG();
		return;
	}

	/* Unmask interrupt */
	r8 = inb(IC_PIC1+1);
	r8 &= ~(1 << irq);
	outb (r8,IC_PIC1+1);
}

324
static struct irq_chip superio_interrupt_type = {
325 326 327
	.name		=	SUPERIO,
	.irq_unmask	=	superio_unmask_irq,
	.irq_mask	=	superio_mask_irq,
L
Linus Torvalds 已提交
328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350
};

#ifdef DEBUG_SUPERIO_INIT
static unsigned short expected_device[3] = {
	PCI_DEVICE_ID_NS_87415,
	PCI_DEVICE_ID_NS_87560_LIO,
	PCI_DEVICE_ID_NS_87560_USB
};
#endif

int superio_fixup_irq(struct pci_dev *pcidev)
{
	int local_irq, i;

#ifdef DEBUG_SUPERIO_INIT
	int fn;
	fn = PCI_FUNC(pcidev->devfn);

	/* Verify the function number matches the expected device id. */
	if (expected_device[fn] != pcidev->device) {
		BUG();
		return -1;
	}
351
	printk("superio_fixup_irq(%s) ven 0x%x dev 0x%x from %pf\n",
L
Linus Torvalds 已提交
352 353 354 355 356 357
		pci_name(pcidev),
		pcidev->vendor, pcidev->device,
		__builtin_return_address(0));
#endif

	for (i = 0; i < 16; i++) {
T
Thomas Gleixner 已提交
358 359
		irq_set_chip_and_handler(i, &superio_interrupt_type,
					 handle_simple_irq);
L
Linus Torvalds 已提交
360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387
	}

	/*
	 * We don't allocate a SuperIO irq for the legacy IO function,
	 * since it is a "bridge". Instead, we will allocate irq's for
	 * each legacy device as they are initialized.
	 */

	switch(pcidev->device) {
	case PCI_DEVICE_ID_NS_87415:		/* Function 0 */
		local_irq = IDE_IRQ;
		break;
	case PCI_DEVICE_ID_NS_87560_LIO:	/* Function 1 */
		sio_dev.lio_pdev = pcidev;	/* save for superio_init() */
		return -1;
	case PCI_DEVICE_ID_NS_87560_USB:	/* Function 2 */
		sio_dev.usb_pdev = pcidev;	/* save for superio_init() */
		local_irq = USB_IRQ;
		break;
	default:
		local_irq = -1;
		BUG();
		break;
	}

	return local_irq;
}

388
static void __init superio_serial_init(void)
L
Linus Torvalds 已提交
389 390 391
{
#ifdef CONFIG_SERIAL_8250
	int retval;
392 393 394 395 396 397
	struct uart_port serial_port;

	memset(&serial_port, 0, sizeof(serial_port));
	serial_port.iotype	= UPIO_PORT;
	serial_port.type	= PORT_16550A;
	serial_port.uartclk	= 115200*16;
398 399
	serial_port.flags	= UPF_FIXED_PORT | UPF_FIXED_TYPE |
				  UPF_BOOT_AUTOCONF;
400 401 402 403 404 405

	/* serial port #1 */
	serial_port.iobase	= sio_dev.sp1_base;
	serial_port.irq		= SP1_IRQ;
	serial_port.line	= 0;
	retval = early_serial_setup(&serial_port);
L
Linus Torvalds 已提交
406
	if (retval < 0) {
407
		printk(KERN_WARNING PFX "Register Serial #0 failed.\n");
L
Linus Torvalds 已提交
408 409 410
		return;
	}

411 412 413 414 415
	/* serial port #2 */
	serial_port.iobase	= sio_dev.sp2_base;
	serial_port.irq		= SP2_IRQ;
	serial_port.line	= 1;
	retval = early_serial_setup(&serial_port);
L
Linus Torvalds 已提交
416
	if (retval < 0)
417
		printk(KERN_WARNING PFX "Register Serial #1 failed.\n");
L
Linus Torvalds 已提交
418 419 420 421
#endif /* CONFIG_SERIAL_8250 */
}


422
static void __init superio_parport_init(void)
L
Linus Torvalds 已提交
423 424 425 426 427 428
{
#ifdef CONFIG_PARPORT_PC
	if (!parport_pc_probe_port(sio_dev.pp_base,
			0 /*base_hi*/,
			PAR_IRQ, 
			PARPORT_DMA_NONE /* dma */,
429 430
			NULL /*struct pci_dev* */,
			0 /* shared irq flags */))
L
Linus Torvalds 已提交
431

432
		printk(KERN_WARNING PFX "Probing parallel port failed.\n");
L
Linus Torvalds 已提交
433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449
#endif	/* CONFIG_PARPORT_PC */
}


static void superio_fixup_pci(struct pci_dev *pdev)
{
	u8 prog;

	pdev->class |= 0x5;
	pci_write_config_byte(pdev, PCI_CLASS_PROG, pdev->class);

	pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
	printk("PCI: Enabled native mode for NS87415 (pif=0x%x)\n", prog);
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415, superio_fixup_pci);


450
static int __init
451
superio_probe(struct pci_dev *dev, const struct pci_device_id *id)
L
Linus Torvalds 已提交
452
{
453
	struct superio_device *sio = &sio_dev;
L
Linus Torvalds 已提交
454 455 456 457 458 459 460 461 462 463 464 465

	/*
	** superio_probe(00:0e.0) ven 0x100b dev 0x2 sv 0x0 sd 0x0 class 0x1018a
	** superio_probe(00:0e.1) ven 0x100b dev 0xe sv 0x0 sd 0x0 class 0x68000
	** superio_probe(00:0e.2) ven 0x100b dev 0x12 sv 0x0 sd 0x0 class 0xc0310
	*/
	DBG_INIT("superio_probe(%s) ven 0x%x dev 0x%x sv 0x%x sd 0x%x class 0x%x\n",
		pci_name(dev),
		dev->vendor, dev->device,
		dev->subsystem_vendor, dev->subsystem_device,
		dev->class);

466
	BUG_ON(!sio->suckyio_irq_enabled);	/* Enabled by PCI_FIXUP_FINAL */
L
Linus Torvalds 已提交
467 468 469 470 471 472 473 474 475 476 477 478 479 480

	if (dev->device == PCI_DEVICE_ID_NS_87560_LIO) {	/* Function 1 */
		superio_parport_init();
		superio_serial_init();
		/* REVISIT XXX : superio_fdc_init() ? */
		return 0;
	} else if (dev->device == PCI_DEVICE_ID_NS_87415) {	/* Function 0 */
		DBG_INIT("superio_probe: ignoring IDE 87415\n");
	} else if (dev->device == PCI_DEVICE_ID_NS_87560_USB) {	/* Function 2 */
		DBG_INIT("superio_probe: ignoring USB OHCI controller\n");
	} else {
		DBG_INIT("superio_probe: WTF? Fire Extinguisher?\n");
	}

481
	/* Let appropriate other driver claim this device. */
L
Linus Torvalds 已提交
482 483 484
	return -ENODEV;
}

485
static const struct pci_device_id superio_tbl[] = {
486 487 488
	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO) },
	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_USB) },
	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415) },
L
Linus Torvalds 已提交
489 490 491 492
	{ 0, }
};

static struct pci_driver superio_driver = {
493
	.name =         SUPERIO,
494 495
	.id_table =     superio_tbl,
	.probe =        superio_probe,
L
Linus Torvalds 已提交
496 497
};

498
module_pci_driver(superio_driver);