3c523.h 10.9 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
#ifndef _3c523_INCLUDE_
#define _3c523_INCLUDE_
/*
	This is basically a hacked version of ni52.h, for the 3c523
	Etherlink/MC.
*/

/*
 * Intel i82586 Ethernet definitions
 *
 * This is an extension to the Linux operating system, and is covered by the
 * same GNU General Public License that covers that work.
 *
 * Copyright 1995 by Chris Beauregard (cpbeaure@undergrad.math.uwaterloo.ca)
 *
 * See 3c523.c for details.
 *
 * $Header: /home/chrisb/linux-1.2.13-3c523/drivers/net/RCS/3c523.h,v 1.6 1996/01/20 05:09:00 chrisb Exp chrisb $
 */

/*
 * where to find the System Configuration Pointer (SCP)
 */
#define SCP_DEFAULT_ADDRESS 0xfffff4


/*
 * System Configuration Pointer Struct
 */

struct scp_struct
{
  unsigned short zero_dum0;	/* has to be zero */
  unsigned char  sysbus;	/* 0=16Bit,1=8Bit */
  unsigned char  zero_dum1;	/* has to be zero for 586 */
  unsigned short zero_dum2;
  unsigned short zero_dum3;
  char          *iscp;		/* pointer to the iscp-block */
};


/*
 * Intermediate System Configuration Pointer (ISCP)
 */
struct iscp_struct
{
  unsigned char  busy;          /* 586 clears after successful init */
  unsigned char  zero_dummy;    /* hast to be zero */
  unsigned short scb_offset;    /* pointeroffset to the scb_base */
  char          *scb_base;      /* base-address of all 16-bit offsets */
};

/*
 * System Control Block (SCB)
 */
struct scb_struct
{
  unsigned short status;        /* status word */
  unsigned short cmd;           /* command word */
  unsigned short cbl_offset;    /* pointeroffset, command block list */
  unsigned short rfa_offset;    /* pointeroffset, receive frame area */
  unsigned short crc_errs;      /* CRC-Error counter */
  unsigned short aln_errs;      /* alignmenterror counter */
  unsigned short rsc_errs;      /* Resourceerror counter */
  unsigned short ovrn_errs;     /* OVerrunerror counter */
};

/*
 * possible command values for the command word
 */
#define RUC_MASK	0x0070	/* mask for RU commands */
#define RUC_NOP		0x0000	/* NOP-command */
#define RUC_START	0x0010	/* start RU */
#define RUC_RESUME	0x0020	/* resume RU after suspend */
#define RUC_SUSPEND	0x0030	/* suspend RU */
#define RUC_ABORT	0x0040	/* abort receiver operation immediately */

#define CUC_MASK	0x0700	/* mask for CU command */
#define CUC_NOP		0x0000	/* NOP-command */
#define CUC_START	0x0100	/* start execution of 1. cmd on the CBL */
#define CUC_RESUME	0x0200	/* resume after suspend */
#define CUC_SUSPEND	0x0300	/* Suspend CU */
#define CUC_ABORT	0x0400	/* abort command operation immediately */

#define ACK_MASK	0xf000	/* mask for ACK command */
#define ACK_CX		0x8000	/* acknowledges STAT_CX */
#define ACK_FR		0x4000	/* ack. STAT_FR */
#define ACK_CNA		0x2000	/* ack. STAT_CNA */
#define ACK_RNR		0x1000	/* ack. STAT_RNR */

/*
 * possible status values for the status word
 */
#define STAT_MASK	0xf000	/* mask for cause of interrupt */
#define STAT_CX		0x8000	/* CU finished cmd with its I bit set */
#define STAT_FR		0x4000	/* RU finished receiving a frame */
#define STAT_CNA	0x2000	/* CU left active state */
#define STAT_RNR	0x1000	/* RU left ready state */

#define CU_STATUS	0x700	/* CU status, 0=idle */
#define CU_SUSPEND	0x100	/* CU is suspended */
#define CU_ACTIVE	0x200	/* CU is active */

#define RU_STATUS	0x70	/* RU status, 0=idle */
#define RU_SUSPEND	0x10	/* RU suspended */
#define RU_NOSPACE	0x20	/* RU no resources */
#define RU_READY	0x40	/* RU is ready */

/*
 * Receive Frame Descriptor (RFD)
 */
struct rfd_struct
{
  unsigned short status;	/* status word */
  unsigned short last;		/* Bit15,Last Frame on List / Bit14,suspend */
  unsigned short next;		/* linkoffset to next RFD */
  unsigned short rbd_offset;	/* pointeroffset to RBD-buffer */
  unsigned char  dest[6];	/* ethernet-address, destination */
  unsigned char  source[6];	/* ethernet-address, source */
  unsigned short length;	/* 802.3 frame-length */
  unsigned short zero_dummy;	/* dummy */
};

#define RFD_LAST     0x8000	/* last: last rfd in the list */
#define RFD_SUSP     0x4000	/* last: suspend RU after  */
#define RFD_ERRMASK  0x0fe1     /* status: errormask */
#define RFD_MATCHADD 0x0002     /* status: Destinationaddress !matches IA */
#define RFD_RNR      0x0200	/* status: receiver out of resources */

/*
 * Receive Buffer Descriptor (RBD)
 */
133
struct rbd_struct
L
Linus Torvalds 已提交
134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184
{
  unsigned short status;	/* status word,number of used bytes in buff */
  unsigned short next;		/* pointeroffset to next RBD */
  char          *buffer;	/* receive buffer address pointer */
  unsigned short size;		/* size of this buffer */
  unsigned short zero_dummy;    /* dummy */
};

#define RBD_LAST	0x8000	/* last buffer */
#define RBD_USED	0x4000	/* this buffer has data */
#define RBD_MASK	0x3fff	/* size-mask for length */

/*
 * Statusvalues for Commands/RFD
 */
#define STAT_COMPL   0x8000	/* status: frame/command is complete */
#define STAT_BUSY    0x4000	/* status: frame/command is busy */
#define STAT_OK      0x2000	/* status: frame/command is ok */

/*
 * Action-Commands
 */
#define CMD_NOP		0x0000	/* NOP */
#define CMD_IASETUP	0x0001	/* initial address setup command */
#define CMD_CONFIGURE	0x0002	/* configure command */
#define CMD_MCSETUP	0x0003	/* MC setup command */
#define CMD_XMIT	0x0004	/* transmit command */
#define CMD_TDR		0x0005	/* time domain reflectometer (TDR) command */
#define CMD_DUMP	0x0006	/* dump command */
#define CMD_DIAGNOSE	0x0007	/* diagnose command */

/*
 * Action command bits
 */
#define CMD_LAST	0x8000	/* indicates last command in the CBL */
#define CMD_SUSPEND	0x4000	/* suspend CU after this CB */
#define CMD_INT		0x2000	/* generate interrupt after execution */

/*
 * NOP - command
 */
struct nop_cmd_struct
{
  unsigned short cmd_status;	/* status of this command */
  unsigned short cmd_cmd;       /* the command itself (+bits) */
  unsigned short cmd_link;      /* offsetpointer to next command */
};

/*
 * IA Setup command
 */
185
struct iasetup_cmd_struct
L
Linus Torvalds 已提交
186 187 188 189 190 191 192 193
{
  unsigned short cmd_status;
  unsigned short cmd_cmd;
  unsigned short cmd_link;
  unsigned char  iaddr[6];
};

/*
194
 * Configure command
L
Linus Torvalds 已提交
195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215
 */
struct configure_cmd_struct
{
  unsigned short cmd_status;
  unsigned short cmd_cmd;
  unsigned short cmd_link;
  unsigned char  byte_cnt;   /* size of the config-cmd */
  unsigned char  fifo;       /* fifo/recv monitor */
  unsigned char  sav_bf;     /* save bad frames (bit7=1)*/
  unsigned char  adr_len;    /* adr_len(0-2),al_loc(3),pream(4-5),loopbak(6-7)*/
  unsigned char  priority;   /* lin_prio(0-2),exp_prio(4-6),bof_metd(7) */
  unsigned char  ifs;        /* inter frame spacing */
  unsigned char  time_low;   /* slot time low */
  unsigned char  time_high;  /* slot time high(0-2) and max. retries(4-7) */
  unsigned char  promisc;    /* promisc-mode(0) , et al (1-7) */
  unsigned char  carr_coll;  /* carrier(0-3)/collision(4-7) stuff */
  unsigned char  fram_len;   /* minimal frame len */
  unsigned char  dummy;	     /* dummy */
};

/*
216
 * Multicast Setup command
L
Linus Torvalds 已提交
217
 */
218
struct mcsetup_cmd_struct
L
Linus Torvalds 已提交
219 220 221 222 223 224 225 226 227
{
  unsigned short cmd_status;
  unsigned short cmd_cmd;
  unsigned short cmd_link;
  unsigned short mc_cnt;		/* number of bytes in the MC-List */
  unsigned char  mc_list[0][6];  	/* pointer to 6 bytes entries */
};

/*
228
 * transmit command
L
Linus Torvalds 已提交
229
 */
230
struct transmit_cmd_struct
L
Linus Torvalds 已提交
231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355
{
  unsigned short cmd_status;
  unsigned short cmd_cmd;
  unsigned short cmd_link;
  unsigned short tbd_offset;	/* pointeroffset to TBD */
  unsigned char  dest[6];       /* destination address of the frame */
  unsigned short length;	/* user defined: 802.3 length / Ether type */
};

#define TCMD_ERRMASK     0x0fa0
#define TCMD_MAXCOLLMASK 0x000f
#define TCMD_MAXCOLL     0x0020
#define TCMD_HEARTBEAT   0x0040
#define TCMD_DEFERRED    0x0080
#define TCMD_UNDERRUN    0x0100
#define TCMD_LOSTCTS     0x0200
#define TCMD_NOCARRIER   0x0400
#define TCMD_LATECOLL    0x0800

struct tdr_cmd_struct
{
  unsigned short cmd_status;
  unsigned short cmd_cmd;
  unsigned short cmd_link;
  unsigned short status;
};

#define TDR_LNK_OK	0x8000	/* No link problem identified */
#define TDR_XCVR_PRB	0x4000	/* indicates a transceiver problem */
#define TDR_ET_OPN	0x2000	/* open, no correct termination */
#define TDR_ET_SRT	0x1000	/* TDR detected a short circuit */
#define TDR_TIMEMASK	0x07ff	/* mask for the time field */

/*
 * Transmit Buffer Descriptor (TBD)
 */
struct tbd_struct
{
  unsigned short size;		/* size + EOF-Flag(15) */
  unsigned short next;          /* pointeroffset to next TBD */
  char          *buffer;        /* pointer to buffer */
};

#define TBD_LAST 0x8000         /* EOF-Flag, indicates last buffer in list */

/*************************************************************************/
/*
Verbatim from the Crynwyr stuff:

    The 3c523 responds with adapter code 0x6042 at slot
registers xxx0 and xxx1.  The setup register is at xxx2 and
contains the following bits:

0: card enable
2,1: csr address select
    00 = 0300
    01 = 1300
    10 = 2300
    11 = 3300
4,3: shared memory address select
    00 = 0c0000
    01 = 0c8000
    10 = 0d0000
    11 = 0d8000
5: set to disable on-board thinnet
7,6: (read-only) shows selected irq
    00 = 12
    01 = 7
    10 = 3
    11 = 9

The interrupt-select register is at xxx3 and uses one bit per irq.

0: int 12
1: int 7
2: int 3
3: int 9

    Again, the documentation stresses that the setup register
should never be written.  The interrupt-select register may be
written with the value corresponding to bits 7.6 in
the setup register to insure corret setup.
*/

/* Offsets from the base I/O address. */
#define	ELMC_SA		0	/* first 6 bytes are IEEE network address */
#define ELMC_CTRL	6	/* control & status register */
#define ELMC_REVISION	7	/* revision register, first 4 bits only */
#define ELMC_IO_EXTENT  8

/* these are the bit selects for the port register 2 */
#define ELMC_STATUS_ENABLED	0x01
#define ELMC_STATUS_CSR_SELECT	0x06
#define ELMC_STATUS_MEMORY_SELECT	0x18
#define ELMC_STATUS_DISABLE_THIN	0x20
#define ELMC_STATUS_IRQ_SELECT	0xc0

/* this is the card id used in the detection code.  You might recognize
it from @6042.adf */
#define ELMC_MCA_ID 0x6042

/*
   The following define the bits for the control & status register

   The bank select registers can be used if more than 16K of memory is
   on the card.  For some stupid reason, bank 3 is the one for the
   bottom 16K, and the card defaults to bank 0.  So we have to set the
   bank to 3 before the card will even think of operating.  To get bank
   3, set BS0 and BS1 to high (of course...)
*/
#define ELMC_CTRL_BS0	0x01	/* RW bank select */
#define ELMC_CTRL_BS1	0x02	/* RW bank select */
#define ELMC_CTRL_INTE	0x04	/* RW interrupt enable, assert high */
#define ELMC_CTRL_INT	0x08	/* R interrupt active, assert high */
/*#define ELMC_CTRL_*	0x10*/	/* reserved */
#define ELMC_CTRL_LBK	0x20	/* RW loopback enable, assert high */
#define ELMC_CTRL_CA	0x40	/* RW channel attention, assert high */
#define ELMC_CTRL_RST	0x80	/* RW 82586 reset, assert low */

/* some handy compound bits */

/* normal operation should have bank 3 and RST high, ints enabled */
#define ELMC_NORMAL (ELMC_CTRL_INTE|ELMC_CTRL_RST|0x3)

#endif /* _3c523_INCLUDE_ */
反馈
建议
客服 返回
顶部