rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

According to datasheet, the S2MPS13X and S2MPS14X should update write
buffer via setting WUDR bit to high after ctrl register is written.

If not, ALARM interrupt of rtc-s5m doesn't happen first time when i use
tools/testing/selftests/timers/rtctest.c test program and hour format is
used to 12 hour mode in Odroid-XU3 board.

One more issue is the RTC doesn't keep time on Odroid-XU3 board when i
turn on board after power off even if RTC battery is connected. It can
be solved as setting WUDR & RUDR bits to high at the same time after
RTC_CTRL register is written. It's same with condition of only writing
ALARM registers, so this is for only S2MPS14 and we should set WUDR &
A_UDR bits to high on S2MPS13.

I can't find any reasonable description about this like fix from
datasheet, but can find similar codes from rtc driver source of
hardkernel kernel and vendor kernel.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v3.16
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add support for RTC controller found on Xilinx Zynq Ultrascale+ MPSoC
platform.
Signed-off-by: NSuneel Garapati <suneel.garapati@xilinx.com>
Acked-by: NMoritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

adds file for description on device node bindings for RTC
found on Xilinx Zynq Ultrascale+ MPSoC.
Signed-off-by: NSuneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The RTC month value is 1-indexed, but the kernel assumes it is 0-indexed.
This may result in the RTC not rolling over correctly.
Signed-off-by: NBibek Basu <bbasu@nvidia.com>
Signed-off-by: NFelix Janda <felix.janda@posteo.de>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

With the SA1100 and PXA RTC drivers be mutually exclusive and no
longer sharing hardware, PXA27x/PXA3xx platforms must use the PXA RTC
driver as the SA1100 platform device is no longer registered.

This change should be almost transparent to userspace. Former users of
pxa-rtc should be aware that 2 RTCs will be available on their kernels,
rtc0 being sa1100-rtc and rtc1 being pxa-rtc. Any userspace relying on
the fact that rtc0 was pxa-rtc should be fixed.

As a consequence:
 - the first reboot after the switch will have the wrong time,
 - on dual boot platform where the other OS programs some logic into the
   sa1100 rtc IP, a lack of fix in userspace, ie. a kernel changing
   sa1100-rtc thinking it is pxa-rtc could have dire consequence, such
   as wiping the other OS data partition.

(Thanks to Robert Jarmik for help on the above commit text.)
Signed-off-by: NRob Herring <robh@kernel.org>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Now that register definitions have been moved to the driver, regs-rtc.h is
no longer used and can be removed.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Now that register definitions have been moved to the driver, we can remove
them from machine specific code.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

SA1100 and PXA differ only in register offsets which are currently
hardcoded in a machine specific header. Some arm64 platforms (PXA1928)
have this RTC block as well (and not the PXA270 variant).

Convert the driver to use ioremap and set the register offsets dynamically.
Since we are touching all the register accesses, convert them all to
readl_relaxed/writel_relaxed.
Signed-off-by: NRob Herring <robh@kernel.org>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The drivers for the SA1100 and PXA RTCs are now mutually exclusive, so
add the memory resource for the sa1100-rtc device. Since the memory
resource is already present in the pxa_rtc_resources, that makes
sa1100_rtc_resources and pxa_rtc_resources equivalent, so use
pxa_rtc_resources for both devices and remove the duplicate
sa1100_rtc_resources.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Currently, the rtc-sa1100 and rtc-pxa drivers co-exist as rtc-pxa has a
superset of functionality. Having 2 drivers sharing the same memory
resource is not allowed by the driver model if resources are properly
declared. This problem was avoided by not adding memory resources to the
SA1100 RTC driver, but that prevents clean-up of the SA1100 driver.

This commit converts the PXA RTC to use the exported SA1100 RTC
functions. Now the sa1100-rtc and pxa-rtc devices are mutually
exclusive, so we must remove the sa1100-rtc from pxa27x and pxa3xx.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rtc-linux@googlegroups.com
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Factor out the RTC initialization from the platform device specific
parts in order to share the RTC device ops with other drivers.
Specifically, it will be shared with rtc-pxa driver.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: rtc-linux@googlegroups.com
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

If ds3232 work on some platform that is not implementing
irq_set_wake, ds3232 will get a WARNING trace in resume.
So fix ds3232->suspended state to false when irq_set_irq_wake
return error.

WARNING: CPU: 0 PID: 729 at kernel/irq/manage.c:604 irq_set_irq_wake+0x4b/0x8c()
Unbalanced IRQ 201 wake disable
Modules linked in:
CPU: 0 PID: 729 Comm: sh Not tainted 3.12.19-rt30+ #25
[<800107d9>] (unwind_backtrace+0x1/0x88) from [<8000e4ef>] (show_stack+0xb/0xc)
[<8000e4ef>] (show_stack+0xb/0xc) from [<802b5fa9>] (dump_stack+0x4d/0x60)
[<802b5fa9>] (dump_stack+0x4d/0x60) from [<800186dd>] (warn_slowpath_common+0x45/0x64)
[<800186dd>] (warn_slowpath_common+0x45/0x64) from [<80018717>] (warn_slowpath_fmt+0x1b/0x24)
[<80018717>] (warn_slowpath_fmt+0x1b/0x24) from [<8003a8d3>] (irq_set_irq_wake+0x4b/0x8c)
[<8003a8d3>] (irq_set_irq_wake+0x4b/0x8c) from [<80204fcb>] (ds3232_resume+0x2d/0x36)
[<80204fcb>] (ds3232_resume+0x2d/0x36) from [<801954c7>] (dpm_run_callback.isra.13+0xb/0x28)
[<801954c7>] (dpm_run_callback.isra.13+0xb/0x28) from [<80195b1b>] (device_resume+0x7b/0xa2)
[<80195b1b>] (device_resume+0x7b/0xa2) from [<80195f0f>] (dpm_resume+0xbb/0x19c)
[<80195f0f>] (dpm_resume+0xbb/0x19c) from [<801960d9>] (dpm_resume_end+0x9/0x12)
[<801960d9>] (dpm_resume_end+0x9/0x12) from [<80037e1d>] (suspend_devices_and_enter+0x17d/0x1d0)
[<80037e1d>] (suspend_devices_and_enter+0x17d/0x1d0) from [<80037ee1>] (pm_suspend+0x71/0x128)
[<80037ee1>] (pm_suspend+0x71/0x128) from [<80037449>] (state_store+0x6d/0x80)
[<80037449>] (state_store+0x6d/0x80) from [<800af4d5>] (sysfs_write_file+0x9f/0xde)
[<800af4d5>] (sysfs_write_file+0x9f/0xde) from [<8007a437>] (vfs_write+0x7b/0x104)
[<8007a437>] (vfs_write+0x7b/0x104) from [<8007a7f7>] (SyS_write+0x27/0x48)
[<8007a7f7>] (SyS_write+0x27/0x48) from [<8000c121>] (ret_fast_syscall+0x1/0x44)
Signed-off-by: NWang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

It's unnecessary the code that assigns info->rtc_clk to NULL in
s3c_rtc_remove.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

It's missed to call clk_unprepare() about info->rtc_src_clk in
s3c_rtc_remove and to call clk_disable_unprepare about info->rtc_clk in
error routine of s3c_rtc_probe.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The clock enable/disable codes for alarm have been removed from
commit 24e14554 ("drivers/rtc/rtc-s3c.c: delete duplicate clock
control") and the clocks are disabled even if alarm is set, so alarm
interrupt can't happen.

The s3c_rtc_setaie function can be called several times with 'enabled'
argument having same value, so it needs to check whether clocks are
enabled or not.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v4.1
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

This driver is using device tree but is not including of.h
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

According to the Armada38x functional errata FE-3124064, writing to
the RTC TIME register may fail. As a workaround, after writing to RTC
TIME register, issue a dummy write of 0x0 twice to the RTC Status
register.  This is the updated implementation of the Errata that
eliminates the need of the long 100ms delay during the RTC set time
procedure.

[gregory.clement@free-electrons.com]: removed the mutex and use the
spinlock again
Signed-off-by: NNadav Haklai <nadavh@marvell.com>
Reviewed-by: NNeta Zur Hershkovits <neta@marvell.com>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Check time validity when reading time as this is when we need to know.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

RX8025_BIT_CTRL2_CTFG was set to 0 only when it was already 0.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

irq_freq is already initialized to 1 in rtc_device_register()
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Wait for the user to set the time to reset the validity bits. Until then,
the time may be invalid.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

rx8025_init_client is modifying ctrl[0] and writing it to RX8025_REG_CTRL2
but ctrl[0] is actually RX8025_REG_CTRL1.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Instead of bailing out, disable alarms and continue when
devm_request_threaded_irq() fails. This allows to still provide some
functionality.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Remove useless error messages, at that point, the user already knows
something went wrong but will not be able to do anything about it anyway.
It is also highly unlikely that some registers are readable/writable
but not some other ones.

Also, transform rx8025_read_reg to be more resemblant to
i2c_smbus_read_byte_data()
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Stop setting the time to epoch when it is invalid. The proper way to handle
that is to return an error when it is invalid instead of returning an
incorrect value.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The datasheet specifies that transfer mode must be 0 for write and either
0x4 (simplified read) or 0 (standard read). 0x8 is not specified, use
standard mode.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The hardware is only capable of handling dates between 2000 and 2099,
enforce that.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Use BIT() instead of hand coding.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

It is useless to print a message when probe fails as the user is already
aware that it failed.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Use devm_request_threaded_irq() so it is not necessary to call free_irq()
explicitly.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The driver currently emulates the concept of threaded IRQ using a
workqueue, switch to threaded IRQ instead.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Remove the useless includes and order the remaining ones alphabetically.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c

Spinlock acquisition/release is moved out of the loop body to get
atomic states of NVRAM reading and writing operations.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>