The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit
function. This was affecting rmmod command not to work for OMAP3
platforms.  The platform driver un-registration for OMAP3 platforms is
perfomed while removing the OHCI module from kernel.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Signed-of-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds support for Accesio USB to Serial adapters, which are built around
FTDI FT232 UARTs.  Tested with the Accesio USB-COM-4SM.
Signed-off-by: NRich Mattes <richmattes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The /sys/kernel/debug/usb/devices file doesn't know about Wireless or
SuperSpeed USB.  This patch (as1416b) teaches it, and updates the
Documentation/usb/proc_sub_info.txt file accordingly.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Vrabel <david.vrabel@csr.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are lots of ZTE USB id's currently not covered by usb/serial. Adds them,
to allow those devices to work properly on Linux.

While here, put the USB ID's for 0x2002/0x2003 at the sorted order.

This patch is based on zte.c file found on MF645.

PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented,
an USB ID for 0x0026.

Not sure why, but I think that 0053 is used by their devices in storage mode only.
So, I opted to keep the comment on this patch.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In today linux-next I got a compile error on usb/host/isp1362-hcd:

drivers/usb/host/isp1362-hcd.c: In function ‘isp1362_hub_control’:
drivers/usb/host/isp1362-hcd.c:1680: error: ‘ohci’ undeclared (first use in this function)

The problem is when the CONFIG_USB_OTG option is enabled.

ohci variable is never declared and there isn't any CONFIG_USB_OTG dependent code
besides the portion defined in isp1362_hub_control.

So I think that maybe USB OTG support is not needed/supported.

This patch removes the CONFIG_USB_OTG dependent block so the driver can compile cleanly.
Signed-off-by: NJavier Martinez Canillas <martinez.javier@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The composite gadget will OOPS if the host sends a control request
targetted to an interface of an un-configured composite device. This patch
prevents this.

The OOPS was observed during WHQL USB CV tests. With this patch, the device
STALLs as per requirement.

Failing test case: From host do the following. I used libusb-1.0

1) Set configuration to zero.
	libusb_control_transfer(device_handle,
		0, /* standard OUT */
		0x9, /* setConfiguration */
		0, 0, NULL, 0, 0);

2) Query current configuratioan.
	libusb_control_transfer(device_handle,
		0x80, /* standard IN*/
		0x8, /* getConfiguration */
		0, 0, data, 1, 0);

3) Send the non-standard ctrl transfer targetted to interface
	libusb_control_transfer(device_handle,
		0x81, /* standard IN to interface*/
		0x6, /* getDescriptor */
		0x2300, 0, data, 0x12, 0);
Signed-off-by: NRoger Quadros <roger.quadros@nokia.com>
Cc: stable <stable@kernel.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets.  When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports.  This prevents attached devices from going
to low power.  Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.

The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled.  However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.

The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware.  As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: NPali Rohár <pali.rohar@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This ioremap() was leaked on an error path.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The protocol code is set 00 in IAD and it's set to 01 in ACM control
interface descriptor in f_acm.c file. Due to this, windows is unable to
install the modem(ACM) driver based on class-subclass-protocol matching.

This patch corrects the protocol code in ACM IAD to the same as in
acm_control_interface_desc protocol code.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NPraveena Nadahally <praveen.nadahally@stericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In today linux-next I got a compile warning due a possible uninitialized variable

This patch solves the issue initializing the variable
Signed-off-by: NJavier Martinez Canillas <martinez.javier@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <damm@opensource.se>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updated Kconfig for langwell otg transceiver driver.
Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is
updated too.
Signed-off-by: NHao Wu <hao.wu@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds one new header file for the common data structure used in
Intel Penwell/Langwell MID Platform OTG Transceiver drivers. After switched
to the common data structure, Langwell/Penwell OTG Transceiver driver will
provide an unified interface to host/client driver.
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NHao Wu <hao.wu@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The "mutex" ftdi->sw_lock is used as a lock and a completion. Convert
it to a real semaphore which allows both.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Corrected the coding style.
Signed-off-by: NMihai Dontu <mihai.dontu@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.

Make ehci_halt a nop if the controller is not in host mode (otherwise it 
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt 
knows we are a tdi device.


Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset

Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset

PS : now we handle correctly the device -> host transition.
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: NMichael Prokop <mika@grml.org>
Acked-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1413) changes g_file_storage to avoid generating a bogus
automatic serial-number string descriptor.  If the user doesn't provide
a valid serial number via a module parameter then a warning is logged
and the gadget won't have any serial string descriptor at all.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
CC: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.

Standardize them a bit.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit f661c6f8 adds a check of the pipe type if
CONFIG_USB_DEBUG is enabled, but it doesn't output anything if this scenario
occurs.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The same expression is tested twice and the result is the same each time.
Instead test for use_dma_ppb as in the test above.

The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@expression@
expression E;
@@

(
* E
  || ... || E
|
* E
  && ... && E
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The __ref* tags may have been confusing for new kernel
developers (I was confused by them for sure) so adding a few
more sentences to comment to clear things up for people who
see those for the first time.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the configuration structure.

This fixes many section mismatches reported by modpost.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: updated for -next]
Signed-off-by: NMichał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the composite driver structure.

This fixes many section mismatches reported by modpost.
Signed-off-by: NMichał Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To accomplish this the function to register a gadget driver takes the bind
function as a second argument.  To make things clearer rename the function
to resemble platform_driver_probe.

This fixes many section mismatches like

	WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
	reference from the variable printer_driver to the function
	.init.text:printer_bind()
	The variable printer_driver references
	the function __init printer_bind()

All callers are fixed.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: NMichał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts a commit which proposed an invalid solution
for a section mismatch.  Next 3 commits will fix it correctly.

Conflicts:

	drivers/usb/gadget/mass_storage.c
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes some of the string registration from the
Multifunction Composite Gadget as composite layer can handle
the iManufacturer and iProduct for us.

This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes string registration from the Mass Storage
Gadget.  With recent changes to the composite framework, all
that we need is handled by the composite layer.  This means
composite registers a string ID for manufacturer and product.

This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The iManufatcurer, iProduct and iSerialNumber composite module
parameters were only used when the gadget driver registers
strings for manufacturer, product and serial number.  If the
gadget never bothered to set corresponding fields in USB device
descriptors those module parameters are ignored.

This commit makes the parameters work even if the strings ID
have not been assigned.  It also changes the way IDs are
overridden -- what IDs are overridden is now saved in
usb_composite_dev structure -- which makes it unnecessary to
modify the string tables the way previous code did.

The commit also adds a iProduct and iManufatcurer fields to the
usb_composite_device structure.  If they are set, appropriate
strings are reserved and added to device descriptor.  This makes
it unnecessary for gadget drivers to maintain code for setting
those.  If iProduct is not set it defaults to
usb_composite_device::name; if iManufatcurer is not set
a default "<system> <release> with <gadget-name>" is used.

The last thing is that if needs_serial field of
usb_composite_device is set and user failed to provided
iSerialNumber parameter a warning is issued.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes some of the string registration from the
FunctionFS Gadget as composite layer can handle the
iManufacturer and iProduct for us.

It also removes some of the module parameters which were
redundant as well as changes the name of others to better much
the module parameter of the composite layer.

Other then that, it also fixes formatting of multiline comments
to match the coding style.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The nofua parameter (optionally ignore SCSI WRITE FUA) was added
to the File Storage Gadget some time ago.  This patch adds the
same functionality to the Mass Storage Function.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The dev_attr_nofua file was created during fsg_bind() but
was never removed.  Made it a bit more symmetrical and added
code to remove the file in fsg_unbind().
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: NAndy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Found while debugging a USB problem and trying to find the mentioned function.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NPraveena Nadahally <praveen.nadahally@stericsson.com>
Signed-off-by: NParirajan Muthalagu <parirajan.muthalagu@stericsson.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add new driver to access the SAM-BA boot application of Atmel AT91SAM
devices.

The SAM-BA firmware cannot handle merged write requests so we cannot use
the generic write implementation (which uses the port write fifo).

Tested with the SAM-BA 2.10 tools and an Atmel at91sam9260-ek.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Tested-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

len is always greater than or equal to zero here.  First of all, it's
type is unsigned and also we only assign it numbers which are greater
than or equal to zero.

Removing the check lets us pull everything in an indent level.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NStephane duverger <stephane.duverger@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>