- 21 5月, 2010 12 次提交
-
-
由 Cliff Cai 提交于
Signed-off-by: NCliff Cai <cliff.cai@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
when we fail to probe(), we can call musb_exit_debugfs(). Allow that by removing section annotations. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
... and simplify the was we read/write from/to DMA COUNT register. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
we can support the musb-specific test modes on the vendor specific range of test selector as stated on USB Specification Table 9-7 Test Mode Selectors. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
for now only a simple register dump entry (which can be rather useful on debugging) and a way to start test modes. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Cliff Cai 提交于
Rather than hardcoding the gpio levels for vrsel, allow the platform resources to handle this so boards can be active high or low. Signed-off-by: NCliff Cai <cliff.cai@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Maulik Mankad 提交于
This patch adds CONFIG_ARCH_OMAP4 macro within MUSB driver. Signed-off-by: NMaulik Mankad <x0082077@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: Olof Johansson <olof@lixom.net> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Maulik Mankad 提交于
This patch updates the Makefile to build the MUSB driver for OMAP4. It also sets the Kconfig options for OMAP4. Signed-off-by: NMaulik Mankad <x0082077@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: Olof Johansson <olof@lixom.net> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Maulik Mankad 提交于
Program the OTG_INTERFSEL register based on transcevier type passed from board file. Adapt signature of musb_platform_init() function for davinci, blackfin and tusb6010. Signed-off-by: NMaulik Mankad <x0082077@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: Olof Johansson <olof@lixom.net> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
boards might want to optimize their fifo configuration to the particular needs of that specific board. Allow that by moving all related data structures to <linux/usb/musb.h> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1349b) clears up the confusion in many USB host controller drivers between port features and port statuses. In mosty cases it's true that the status bit is in the position given by the corresponding feature value, but that's not always true and it's not guaranteed in the USB spec. There's no functional change, just replacing expressions of the form (1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Eric Lescouet 提交于
The usbcore headers: hcd.h and hub.h are shared between usbcore, HCDs and a couple of other drivers (e.g. USBIP modules). So, it makes sense to move them into a more public location and to cleanup dependency of those modules on kernel internal headers. This patch moves hcd.h from drivers/usb/core into include/linux/usb/ Signed-of-by: NEric Lescouet <eric@lescouet.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 01 5月, 2010 11 次提交
-
-
由 Tony Lindgren 提交于
Commit 18eabe23 introduced DMA buffer ownership. Fix tusb6010 accordingly. To compile, also dummy musb_platform_save and restore functions need to be added. Also change the order of musb_read_fifo() to happen after dma_cache_maint to have the DMA operations completed before moving the remaining unaligned bytes with PIO. The DMA access and PIO touch different areas of the FIFO, so this change only makes the code a bit easier to follow. Tested on n810 and g_ether with variable size ping test. The test seems to fail for some ping sizes, but that seems to be a different problem. Signed-off-by: NTony Lindgren <tony@atomide.com> Acked-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
This function forgets to call usb_remove_hcd() or musb_gadget_cleanup() iff sysfs_create_group() fails. [ felipe.balbi@nokia.com : review the entire error path not only when we fail hcd or gadget ] Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
CONFIG_ARCH_DAVINCI now embraces both the "real" DaVinci and DA8xx/OMAP-L1x -- on which the DaVinci glue layer won't work. Change the Makefile dependency to CONFIG_ARCH_DAVINCI_DMx which corresponds to "real" DaVinci. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
musb_platform_exit() is called twice from musb_init_controller() iff controller initialization fails. Move the call (and the DevCtl register writes surrounding it) from musb_free() to musb_remove(). Fix mispalced and now incorrect 'goto's in musb_init_controller(). Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Remove duplicate/unbalanced call to clk_put() from musb_platform_exit() -- clk_put() gets called from musb_core.c anyway... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
This function forgets to call clk_disable() iff reading the USB module version register returns 0. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Resetting 'musb->clock' to NULL in musb_shutdown() prevents musb_platform_exit() from properly disabling the clock when unloading the driver -- don't do it. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Remove duplicate/unbalanced calls to clk_disable()/clk_put() in musb_free(): - clk_disable() is called by musb_platform_exit() just prior to this call; - clk_put() is called by the callers of musb_free() prior to calling it... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Dan Carpenter 提交于
We assign "urb->hcpriv = qh;" a few lines down. I'm pretty sure we want it "urb->hcpriv" to be NULL not a freed value. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ajay Kumar Gupta 提交于
Added the missing BUS_CONTROL register in musb save/restore routines. Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Commit a5073b52 (musb_gadget: fix unhandled endpoint 0 IRQs) misses this change to blackfin.c: stop faking successful result of blackfin_interrupt() and emitting a debug message on an unhandled interrupt. Signed-off-by: NSergei Shtylyov <sshtylyov@mvista.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 19 3月, 2010 5 次提交
-
-
由 Felipe Balbi 提交于
... and avoid a compilation if we disable host side of musb. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Mike Frysinger 提交于
The recent commit "usb: musb: Add context save and restore support" added some stubs for the Blackfin code so things would compile, but it also added a bunch of warnings due to missing return statements. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Mike Frysinger 提交于
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY. However, it has no ULPI support - so there are no registers at all. That means accesses to ULPI_BUSCONTROL have to be abstracted away like other MUSB registers. This fixes building for Blackfin parts again. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Acked-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Tony Lindgren 提交于
CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3. But since drivers/usb/musb/omap2430.c use CONFIG_PM for these registers and functions, do the same for the header. Otherwise we get the following for most omap3 defconfigs: drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do' drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while' drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do' drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while' Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sonic Zhang 提交于
The recent commit "usb: musb: Fix for isochronous IN transfer" (f82a689f) seems to have been against an older kernel version. It uses the old style naming of variables. Unfortunately, this breaks building for most MUSB users out there since "bDesiredMode" has been renamed to "desired_mode". Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Acked-by: NFelipe Balbi <felipe.balbi@nokia.com> Acked-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 03 3月, 2010 11 次提交
-
-
由 Roel Kluin 提交于
The removed part always evaluates to false. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
-
由 Cliff Cai 提交于
Trying to use double buffer modes in RTL versions <2.0 may result in infinite hangs or data corruption. So avoid them with older versions. Signed-off-by: NCliff Cai <cliff.cai@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Cliff Cai 提交于
All current Blackfin parts are using RTL v1.9, but they don't expose the hardware registers to probe this dynamically. So hardcode the version to v1.9 for now. Need to move the local hwvers related defines higher up in the header so that sub-musb headers may utilize them. Signed-off-by: NCliff Cai <cliff.cai@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
we were printing the info about musb probe too early where it was still possible for things to go wrong. Move the down right before the return 0 statement. While at that also convert pr_info to dev_info. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
when probe() fails, we should iounmap() the mapped address. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
Trivial patch, no functional changes. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
... and even added a flag to struct musb, so let's use that. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Felipe Balbi 提交于
we have those addresses already ioremaped, so let's use our __raw_readl/writel wrappers. Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ajay Kumar Gupta 提交于
Adding support for MUSB register save and restore during system suspend and resume. Changes: - Added musb_save/restore_context() functions - Added platform specific musb_platform_save/restore_context() to handle platform specific jobs. - Maintaining BlackFin compatibility by adding read/write functions for registers which are not available in BlackFin Tested system suspend and resume on OMAP3EVM board. Signed-off-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Roel Kluin 提交于
Test whether tusb_dma is not NULL before dereferencing Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ajay Kumar Gupta 提交于
Some of the board might use external Vbus power supply on musb interface which would require to program ULPI_BUSCONTROL register. Adding 'extvbus' flag which can be set from such boards which will be checked at musb driver files before programming ULPI_BUSCONTROL. Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-