Convert the driver to blk-mq.
Beside of moving to the modern block interface this change boosts
also the performance of the driver.

nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron NAND 256MiB 3,3V 8-bit
nand: 256MiB, SLC, page size: 2048, OOB size: 64

root@debian-armhf:~# dd if=/dev/ubiblock0_0 of=/dev/zero bs=1M
243+1 records in
243+1 records out
255080448 bytes (255 MB) copied, 4.39295 s, 58.1 MB/s

vs.

root@debian-armhf:~# dd if=/dev/ubiblock0_0 of=/dev/zero bs=1M
243+1 records in
243+1 records out
255080448 bytes (255 MB) copied, 2.87676 s, 88.7 MB/s

Cc: hch@infradead.org
Cc: axboe@fb.com
Cc: tom.leiming@gmail.com
Signed-off-by: NRichard Weinberger <richard@nod.at>
Tested-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: NJens Axboe <axboe@fb.com>
Acked-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>

Adds a new set of functions to deal with scatter gather.
ubi_eba_read_leb_sg() will read from a LEB into a scatter gather list.
The new data structure struct ubi_sgl will be used within UBI to
hold the scatter gather list itself and metadata to have a cursor
within the list.
Signed-off-by: NRichard Weinberger <richard@nod.at>
Tested-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>

By using UBI_METAONLY in rename_volumes() it is now possible to rename
an UBI volume atomically while it is open for writing.
This is useful for firmware upgrades.

Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: NRichard Weinberger <richard@nod.at>
Tested-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NChristoph Fritz <chf.fritz@googlemail.com>
Tested-by: NAndrew Murray <amurray@embedded-bits.co.uk>

UBI_METAONLY is a new open mode for UBI volumes, it indicates
that only meta data is being changed.
Meta data in terms of UBI volumes means data which is stored in the
UBI volume table but not on the volume itself.
While it does not interfere with UBI_READONLY and UBI_READWRITE
it is not allowed to use UBI_METAONLY together with UBI_EXCLUSIVE.

Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: NRichard Weinberger <richard@nod.at>
Tested-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Tested-by: NChristoph Fritz <chf.fritz@googlemail.com>
Tested-by: NAndrew Murray <amurray@embedded-bits.co.uk>

In the case when alloc_netdev fails we return NULL to a caller. But there is no
check for NULL in the probe drivers. This patch changes NULL to an error
pointer. The function description is amended to reflect what we may get
returned.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Use the return value of dma_map_single(), rather than calling
  virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers.  This is unsafe because:

- In general, register writes are not serialised with DMA, so we still
  have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
  be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
  RX DMA at the next packet boundary

I applied this patch to the driver to detect DMA writes to freed
buffers:

> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
>  	/* Free Rx skb ringbuffer */
>  	if (mdp->rx_skbuff) {
>  		for (i = 0; i < mdp->num_rx_ring; i++)
> +			memcpy(mdp->rx_skbuff[i]->data,
> +			       "Hello, world", 12);
> +		msleep(100);
> +		for (i = 0; i < mdp->num_rx_ring; i++) {
> +			WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> +				       "Hello, world", 12));
>  			dev_kfree_skb(mdp->rx_skbuff[i]);
> +		}
>  	}
>  	kfree(mdp->rx_skbuff);
>  	mdp->rx_skbuff = NULL;

then ran the loop:

    while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.  The
warning fired several times a minute.

To fix these issues:

- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
  perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
  frame, disable egress and wait a reasonable time to reach a
  packet boundary before resetting
- Update statistics before resetting

(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse.  These errors are visible in the
statistics anyway.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.

Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.

Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: NAhmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: NAhmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.

This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: NAhmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.

Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.

While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]

In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]

Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.

[1] http://article.gmane.org/gmane.linux.network/239442
    http://www.webcitation.org/6Vr2yagAQ

[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
    889b77f7

[3] Stacktrace:

 <IRQ>  [<ffffffff8158de87>] dump_stack+0x45/0x57
 [<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
 [<ffffffff815904b1>] __schedule+0x5f1/0x700
 [<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
 [<ffffffff81590684>] schedule+0x24/0x70
 [<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
 [<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
 [<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
 [<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
 [<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
 [<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
 [<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
 [<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
 [<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
 [<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
 [<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
 [<ffffffff81069f65>] ? local_clock+0x15/0x30
 [<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
 [<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
 [<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
 [<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
 [<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
 [<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
 [<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
 [<ffffffff81004dfd>] handle_irq+0x1d/0x30
 [<ffffffff81004727>] do_IRQ+0x57/0x100
 [<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: NAhmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Commit 69ad0dd7
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date:   Mon May 19 13:59:59 2014 -0300

    net: mv643xx_eth: Use dma_map_single() to map the skb fragments

caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.

This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.

This commit also fixes the error path in txq_init() to release the
resources properly.

Fixes: 69ad0dd7 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq().  This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it.  Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.

I could easily trigger a crash by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done

and 'ping -f' toward the sh_eth port from another machine.

To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
  should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
  and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
  sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
  handlers before clearing EESIPR in sh_eth_close() and
  sh_eth_set_ringparam()

After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned.  Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.

What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.

I could easily trigger this by running the loop:

   while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding.  This could result in leaking sensitive
data.  We also pass different lengths to dma_map_single() and
dma_unmap_single().

Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.

Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.

Fixes: d9ba8f9e (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Array of platform_device_id elements should be terminated with empty
element.

Fixes: 5bccae6e ("rtc: s5m-rtc: add real-time clock driver for s5m8767")
Signed-off-by: NAndrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Do not wait for channel command buffers in IPA commands.
The potential wait could be done while holding a spin lock and causes
in recent kernels such a bug if kernel lock debugging is enabled:

kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c:
794
kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager
kernel: 2 locks held by NetworkManager/2031:
kernel:  #0:  (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50
kernel:  #1:  (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50
kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1
kernel:        00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000
               00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a
               0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b
               00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000
               0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0
kernel: Call Trace:
kernel: ([<00000000001128b0>] show_trace+0xf8/0x158)
kernel:  [<000000000011297a>] show_stack+0x6a/0xe8
kernel:  [<00000000007e995a>] dump_stack+0x82/0xb0
kernel:  [<000000000017d668>] ___might_sleep+0x170/0x228
kernel:  [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth]
kernel:  [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth]
kernel:  [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3]
kernel:  [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3]
kernel:  [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3]
kernel:  [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50
kernel:  [<00000000006cff90>] __dev_open+0xe0/0x140
kernel:  [<00000000006d02a0>] __dev_change_flags+0xa0/0x178
kernel:  [<00000000006d03a8>] dev_change_flags+0x30/0x70
kernel:  [<00000000006e14ee>] do_setlink+0x346/0x9a0
...

The device driver has plenty of command buffers available
per channel for channel command communication.
In the extremely rare case when there is no command buffer
available, return a NULL pointer and issue a warning
in the kernel log. The caller handles the case when
a NULL pointer is encountered and returns an error.

In the case the wait for command buffer is possible
(because no lock is held as in the OSN case), still wait
until a channel command buffer is available.
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the functions that are registering and unregistering MAC
addresses in the qeth-handled hardware, remove callback functions
that are unnesessary, as only the return code is analyzed.
Translate hardware response codes to semi-standard 'errno'-like
codes for readability.

Add kernel-doc description to the internal API function
qeth_send_control_data().
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Reviewed-by: NThomas-Mich Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ip6_route_output() always returns a valid dst pointer unlike in IPv4
case. So the validation has to be different from the IPv4 path. Correcting
that error in this patch.

This was picked up by a static checker with a following warning -

   drivers/net/ipvlan/ipvlan_core.c:380 ipvlan_process_v6_outbound()
        warn: 'dst' isn't an ERR_PTR
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.

If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: NMike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: d75b1ade ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ffcc3936 ("dm: enhance internal suspend and resume interface")
attempted to handle multiple internal suspends on the same device, but
it did that incorrectly.  When these functions are called in this order
on the same device the device is no longer suspended, but it should be:
	dm_internal_suspend_noflush
	dm_internal_suspend_noflush
	dm_internal_resume

Fix this bug by maintaining an 'internal_suspend_count' and resuming
the device when this count drops to zero.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Use ATTRIBUTE_GROUPS macro to simplify the code a bit.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

Use module_pci_driver to simplify the code a bit.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NJean Delvare <jdelvare@suse.de>

On many motherboards, for an unknown reason, the thermal sensor seems
to be disabled and will return a constant temperature value of 36.5
degrees Celsius. Don't bind to the device in that case, so that we
don't report this bogus value to userspace.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

Use devm_hwmon_device_register_with_groups() to simplify the code a
bit.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.

Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Tested-by: NRomain Dolbeau <romain@dolbeau.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register.  The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 02b2aaaa.

This interface was determined to be flawed and required too invasive a
fix for the RC cycle. This will be revisited in 3.20.
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>

Introduce a new variable to count the number of allocated migration
structures.  The existing variable cache->nr_migrations became
overloaded.  It was used to:

 i) track of the number of migrations in flight for the purposes of
    quiescing during suspend.

 ii) to estimate the amount of background IO occuring.

Recent discard changes meant that REQ_DISCARD bios are processed with
a migration.  Discards are not background IO so nr_migrations was not
incremented.  However this could cause quiescing to complete early.

(i) is now handled with a new variable cache->nr_allocated_migrations.
cache->nr_migrations has been renamed cache->nr_io_migrations.
cleanup_migration() is now called free_io_migration(), since it
decrements that variable.

Also, remove the unused cache->next_migration variable that got replaced
with with prealloc_structs a while ago.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

If a DM table is reloaded with an inactive table when the device is not
suspended (normal procedure for LVM2), then there will be two dm-bufio
objects that can diverge.  This can lead to a situation where the
inactive table uses bufio to read metadata at the same time the active
table writes metadata -- resulting in the inactive table having stale
metadata buffers once it is promoted to the active table slot.

Fix this by using reference counting and a global list of cache metadata
objects to ensure there is only one metadata object per metadata device.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Introduce selftests for overlays using sub-devices present
in children nodes.
Signed-off-by: NPantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

James reported:
> After e513cc1c module: Remove stop_machine from module unloading,
> module_refcount() is returning (unsigned long)-1 when called from within
> a routine that runs in module_exit.  This is confusing the scsi device
> put code which is coded to detect a module_refcount() of zero for
> running within a module exit routine and not try to do another
> module_put.  The fix is to restore the original behaviour of
> module_refcount() and return zero if we're running inside an exit
> routine.

The correct fix is to turn try_module_get() into __module_get(), and
always do the module_put().
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

cppcheck found the following issue:
(warning) Logical conjunction always evaluates to false:
  alloc_len < 4 && alloc_len > 65535.

..the test should be instead:

  if (alloc_len < 4 || alloc_len > 65536)

This error was introduced by recent commit 38d5c833
("scsi_debug: add Report supported opcodes+tmfs; Compare and write")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

radeon_vm_map_gart can use rdev->gart.pages_entry instead.

Also move the masking of the page address to radeon_vm_map_gart from its
callers.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>