When a kthread function returns, it branches to do_exit(). However, the
unwinding information isn't valid anymore and any stack trace caused by
do_exit() may be incorrect. This patch adds a kernel_thread_exit()
function and annotated with '.cantunwind' so that the unwinder stops
when reaching it.
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are situations where the unwinder goes beyond stack boundaries and
unwinds random data. This patch moves the stack boundaries check after
the unwind_exec_insn() call and adds an extra check for possible
infinite loops (like "mov pc, lr" with pc == lr).

The patch also fixes a bug in the unwind instructions interpreter. The
0xb0 instruction can only set PC to LR if this wasn't already set by
a previous instruction (this is used on exceptions taken while in kernel
mode where svc_entry is annotated with ".save {r0 - pc}").
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Not discarding these sections when hotplug isn't available prevents the
kernel from building.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

From: Min Zhang <mzhang@mvista.com>

Add alignment fault fixup support for 32-bit Thumb-2 LDM, LDRD, POP,
PUSH, STM and STRD instructions.  Alignment fault fixup support for
the remaining 32-bit Thumb-2 load/store instruction cases is not
included since ARMv6 and later processors include hardware support
for loads and stores of unaligned words and halfwords.
Signed-off-by: NMin Zhang <mzhang@mvista.com>
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The cpu member of struct irq_desc was recently renamed to node. The
patch renames the ARM references to the old member.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This header file is needed for twd_base.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'for-rmk' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel

ia64 was assigning resources to root busses after allocations had
been made for child busses.  Calling pcibios_setup_root_windows() from
pcibios_fixup_bus() solves this problem by assigning the resources to
the root bus before child busses are scanned.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Tested-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This function was only used by pci_claim_resource(), and the last commit
deleted that use.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of starting from the iomem or ioport roots, start from the
parent bus' resources.  This fixes a bug where child resources would
appear above their parents resources if they had the same size.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Tested-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Convert ia64 to use int-ll64.h
  [IA64] Fix build error in paravirt_patchlist.c
  [IA64] ia64 does not need umount2() syscall
  [IA64] hook up new rt_tgsigqueueinfo syscall
  [IA64] msi_ia64.c dmar_msi_type should be static
  [IA64] remove obsolete hw_interrupt_type
  [IA64] remove obsolete irq_desc_t typedef
  [IA64] remove obsolete no_irq_type
  [IA64] unexport fpswa.h

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: early init for MFD running regulators
  mfd: fix tmio related warnings
  mfd: asic3: enable SD/SDIO cell
  mfd: asic3: enable DS1WM cell
  mfd: asic3: remove SD/SDIO controller register definitions
  mfd: asic3: use resource_size macro instead of local variable
  mfd: add ASIC3 IRQ numbers
  mfd: asic3: add clock handling for MFD cells
  mfd: asic3: add asic3_set_register common operation
  mfd: Fix Kconfig help text for WM8350
  mfd: add PCAP driver
  mfd: add U300 AB3100 core support
  drivers/mfd: remove obsolete irq_desc_t typedef
  mfd/pcf50633-gpio.c: add MODULE_LICENSE
  mfd: Mark WM8350 mask revision as readable to match silicon
  mfd: Mark clocks_init as non-init in twl4030-core.c
  mfd: Correct readability of WM8350 register 227

* 'kmemleak' of git://linux-arm.org/linux-2.6:
  kmemleak: Fix some typos in comments
  kmemleak: Rename kmemleak_panic to kmemleak_stop
  kmemleak: Only use GFP_KERNEL|GFP_ATOMIC for the internal allocations

For MFDs running regulator cores, we really want them to be brought up early
during boot.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMike Rapoport <mike@compulab.co.il>

We can not have .driver_data as const since platform_set_drvdata() doesnt take
a const.
The hclk mmc_data field can be const though.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This enables the ASIC3's SD/SDIO MFD cell, supported by the tmio_mmc driver.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This enables the ASIC3's DS1WM MFD cell, supported by the ds1wm driver.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Only the base addresses remain, as they are needed to set up
the IOMEM resources.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This should make the code a little bit easier to read.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

IRQ number definitions for PWM, LED, SPI and OWM (ds1wm).
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since ASIC3 has to work on both PXA and S3C and since their
struct clk implementations differ, we can't register out
clocks with the clkdev mechanism (yet?).
For now we have to keep clock handling internal to this
driver and enable/disable the clocks via the
mfd_cell->enable/disable functions.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Used to configure single bits of the SDHWCTRL_SDCONF and EXTCF_RESET/SELECT
registers needed for DS1WM, MMC/SDIO and PCMCIA functionality.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

More with the grammar.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.

It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.

This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Reviewed-by: NMike Rapoport <mike@compulab.co.il>
Reviewed-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The defines and typedefs (hw_interrupt_type, no_irq_type, irq_desc_t) have
been kept around for migration reasons.  After more than two years it's
time to remove them finally.

This patch cleans up one of the remaining users.  When all such patches
hit mainline we can remove the defines and typedefs finally.

Impact: cleanup

Convert the last remaining users and remove the typedef.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add the missing MODULE_LICENSE("GPL").
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

No impact unless someone has written additional kernel code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Impact: Fix section mismatch.

clocks_init() has been called from twl4030_probe() which is a non-init
function. Since probing can be done anytime so clocks_init will be
called anytime too. So we mark clock_init() as non-init.

LD      drivers/mfd/built-in.o
WARNING: drivers/mfd/built-in.o(.text+0x8dd9): Section mismatch in
reference from the function twl4030_probe() to the function
.init.text:clocks_init()
The function twl4030_probe() references
the function __init clocks_init().
This is often because twl4030_probe lacks a __init
annotation or the annotation of clocks_init is wrong.
Signed-off-by: NRakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This includes the USB current limit status override which is used in the
power management driver.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This is to avoid the confusion created by the "panic" word.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>

Kmemleak allocates memory for pointer tracking and it tries to avoid
using GFP_ATOMIC if the caller doesn't require it. However other gfp
flags may be passed by the caller which aren't required by kmemleak.
This patch filters the gfp flags so that only GFP_KERNEL | GFP_ATOMIC
are used.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NPekka Enberg <penberg@cs.helsinki.fi>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] cpumask: new cpumask operators for arch/x86/kernel/cpu/cpufreq/powernow-k8.c
  [CPUFREQ] cpumask: avoid playing with cpus_allowed in powernow-k8.c
  [CPUFREQ] cpumask: avoid cpumask games in arch/x86/kernel/cpu/cpufreq/speedstep-centrino.c
  [CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c
  [CPUFREQ] powernow-k8: get drv data for correct CPU
  [CPUFREQ] powernow-k8: read P-state from HW
  [CPUFREQ] reduce scope of ACPI_PSS_BIOS_BUG_MSG[]
  [CPUFREQ] Clean up convoluted code in arch/x86/kernel/tsc.c:time_cpufreq_notifier()
  [CPUFREQ] minor correction to cpu-freq documentation
  [CPUFREQ] powernow-k8.c: mess cleanup
  [CPUFREQ] Only set sampling_rate_max deprecated, sampling_rate_min is useful
  [CPUFREQ] powernow-k8: Set transition latency to 1 if ACPI tables export 0
  [CPUFREQ] ondemand: Uncouple minimal sampling rate from HZ in NO_HZ case

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
  [SCSI] aic79xx: make driver respect nvram for IU and QAS settings
  [SCSI] don't attach ULD to Dell Universal Xport
  [SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
  [SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
  [SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
  [SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
  [SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
  [SCSI] qla2xxx: Resolve a performance issue in interrupt
  [SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
  [SCSI] nsp_cs: time_out reaches -1
  [SCSI] qla2xxx: fix printk format warnings
  [SCSI] ncr53c8xx: div reaches -1
  [SCSI] compat: don't perform unneeded copy in sg_io code
  [SCSI] zfcp: Update FC pass-through support
  [SCSI] zfcp: Add FC pass-through support
  [SCSI] FC Pass Thru support

* 'linux-next' of git://git.infradead.org/ubi-2.6: (21 commits)
  UBI: add reboot notifier
  UBI: handle more error codes
  UBI: fix multiple spelling typos
  UBI: fix kmem_cache_free on error patch
  UBI: print amount of reserved PEBs
  UBI: improve messages in the WL worker
  UBI: make gluebi a separate module
  UBI: remove built-in gluebi
  UBI: add notification API
  UBI: do not switch to R/O mode on read errors
  UBI: fix and clean-up error paths in WL worker
  UBI: introduce new constants
  UBI: fix race condition
  UBI: minor serialization fix
  UBI: do not panic if volume check fails
  UBI: add dump_stack in checking code
  UBI: fix races in I/O debugging checks
  UBI: small debugging code optimization
  UBI: improve debugging messages
  UBI: re-name volumes_mutex to device_mutex
  ...

* 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: start using hrtimers
  hrtimer: export ktime_add_safe
  UBIFS: do not forget to register BDI device
  UBIFS: allow sync option in rootflags
  UBIFS: remove dead code
  UBIFS: use anonymous device
  UBIFS: return proper error code if the compr is not present
  UBIFS: return error if link and unlink race
  UBIFS: reset no_space flag after inode deletion

For it is only in linux-next at this stage.

Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>