The following patch gets rid of CONFIG_TSI108_BRIDGE.  I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.

(1) the reason to rewrite serial_in:

    TSI108 rev Z1 version ERRATA.  Reading the UART's Interrupt
    Identification Register (IIR) clears the Transmit Holding Register
    Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
    are not enabled in the Interrupt Enable Register (IER).  This leads to
    loss of the interrupts.  Interrupts are not cleared when reading UART
    registers as 32-bit word.

(2) the reason to rewrite serial_out:

    Check for UART_IER_UUE bit in the autoconfig routine.  This section
    of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
    reserved for internal use.  They are R/W bits.  In addition to
    incorrect identification, changing these bits (from 00) will make
    Tsi108/109 UART non-functional.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char.  Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl.  If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Also fixes all serial drivers.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Patch from Ben Dooks

Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch includes a number of updates to the AT91RM9200 serial driver.

Changes include:
1. Conversion to a platform_driver.  [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91.  This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support.  [David Brownell]

There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The locking for the uart_port is over complicated, and can be
simplified if we introduce a flag to indicate that a port is "dead"
and will be removed.

This also helps the validator because it removes a case of non-nested
unlock ordering.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Glen Turner reported that writing LFCR rather than the more
traditional CRLF causes issues with some terminals.

Since this aflicts many serial drivers, extract the common code
to a library function (uart_console_write) and arrange for each
driver to supply a "putchar" function.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since it can do things like BREAK and HUP, we implement
this as a serial uart driver.

This still needs interrupt probing code, as I haven't figured
out how interrupts will work or be probed for on SUN4V yet.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same reasoning as commit 747c8a55
but this time we're making uart_port flags a bitwise type - not
all of these flags correspond with the old ASYNC_ flags, so there
is the possibility for bugs if the wrong ASYNC_* constants are
used.  Always use UPF_* constants for uart_port->flags.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The previous change found a bug in the serial SAK handling - because
we were looking for UPF_SAK set in uart_info->flags, we would never
raise a SAK condition.  UPF_SAK is in uart_port->flags.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The potential for confusing the flags is fairly high.  Make
uart_info's flags a bitwise type so sparse can check that the
right flag definitions are used with the right structure.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

No one should write to the port->ops structure, so make it constant.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The functionality UPF_BOOT_ONLYMCA provided has been replaced by
the 8250_mca module, which only registers MCA ports if MCA is
present.

UPF_AUTOPROBE has no functional effect - in fact, it's never
tested.  Only ibmasm set the flag.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

semaphore to mutex conversion.

the conversion was generated via scripts, and the result was validated
automatically via a script as well.

build and boot tested.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Andrew Victor

This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.

This patch is the Serial driver.

This version uses the newly re-written GPL'ed hardware headers.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Sascha Hauer

This patch adds PORT_NETX for supporting the Hilscher netx embedded
UARTs.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: NPantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The PORT_* macros must be uniquely numbered.  This fixes the
definitions.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Proud member of Uglyhacks'R'US.
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NRussell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

When SUPPORT_SYSRQ is false, gcc can emit warnings for
the uart_handle_sysrq_char() that results.  Using an
empty inline returning zero kills the warning.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Patch from Sascha Hauer

This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use tabs for formatting like anywhere else in this file.

Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I think it's about time to make the build a little more vocal about the
expiry of these functions.  Due to recent discussions with problems in
the console initialisation vs power manglement, I'd like to move the
date forward to September.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add uart_insert_char(), which handles inserting characters into the
flip buffer.  This helper function handles the correct semantics
for handling overrun in addition to inserting normal characters.
Signed-off-by: NRussell King <rmk@arm.linux.org.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!