Only MULTIPLATFORM has phbs_remap_io.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

This also make klimit have the same type on 32-bit as on 64-bit,
namely unsigned long, and defines and initializes it in one place.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

This patch moves a bunch more files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc.  The file affected are:
	hvcall.h
	proc_ppc64.c
	sysfs.c
	lparcfg.c
	rtas_pci.c

The only changes apart from the move and corresponding Makefile
changes are:
	- #ifndef/#define in includes updated to _ASM_POWERPC_ form
	- trailing whitespace removed
	- comments giving full paths removed

Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.

This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.

That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

That DART (U3 iommu) code didn't properly scale the number of entries
when using !4k pages. That caused crashes when booting G5s with more
than 2Gb of RAM. This fixes it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch makes the kernel use a different kmem cache for PMD pages
as they are smaller than PTE pages. Avoids waste of memory.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>

This makes the memory examine/change command print the address as
8 digits instead of 16, and makes the memory dump command print
4 4-byte values per line instead of 2 8-byte values.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is at the request of the glibc folks, who want to use these bits
to select libraries optimized for the microarchitecture and new
instructions in these processors.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We were getting the last_jiffy per-cpu variable set ahead of the current
timebase in smp_space_timers on SMP machines.  This caused the loop in
timer_interrupt to loop virtually forever, since tb_ticks_since assumes
that it will never be called with the timebase behind the last_jiffy
value.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A couple of bugs crept in with the merge of smp.c...
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Gcc 4 doesn't like being told to inline a recursive function...
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch merges platform codes.  systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32.  Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs.  A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros.  It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files.  Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.

ppc_asm.h is now for use in .S files *only*, and a #error enforces
that.  As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.

While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.

Built and booted on pSeries, Maple and iSeries (ARCH=powerpc).  Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

scanlog.c is only compiled on pSeries.  Thus, this patch moves it to
platforms/pseries.

Built and booted on pSeries LPAR (ARCH=powerpc and ARCH=ppc64).  Built
for iSeries (ARCH=powerpc).
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere.  This patch, therefore, merges both headers.  Notable
points:
	- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64.  These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
	- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf.  These too should be merged and consolidated later.
	- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32.  In the merged version it's in
cacheflush.h
	- On ppc32 flush_icache_range() is a normal function from
misc.S.  On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush.  This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
	- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
	- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
	- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported).  Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely.  It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.

Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc).  Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).

Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc).  Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64).  Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We had a "64" that didn't get changed to BITS_PER_LONG, resulting
in find_next_bit not working correctly.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds code to work around some problems with old versions of
Open Firmware, such as on the early powermacs (7500 etc.) and the
"Longtrail" CHRP machine.  On these machines we have to claim
the physical and virtual address ranges explicitly when claiming
memory and then set up a V->P mapping.

The Longtrail has more problems: setprop doesn't work, and we have
to set an "allow-reclaim" variable to 0 in order to get claim on
physical memory ranges to fail if the memory is already claimed.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

14-eeh-device-bar-save.patch

After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device.  This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.

Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device.  Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

13-eeh-recovery-support-routines.patch

EEH Recovery support routines

This patch adds routines required to help drive the recovery of
EEH-frozen slots.  The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

12-eeh-event-dispatcher.patch

ppc64: EEH Recovery dispatcher thread

This patch adds a mechanism to create recovery threads when an
EEH event is received.  Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.

A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time.  This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

11-eeh-move-to-powerpc.patch

Move arch/ppc64/kernel/eeh.c to arch//powerpc/platforms/pseries/eeh.c
No other changes (except for Makefile to build it)
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

10-EEH-enable-bugfix.patch

Bugfix: With the curent linux-2.6.14-rc2-git6, EEH errors are
ignored because thier detection requires an unused, uninitialized
flag to be set.  This patch removes the unused flag.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

09-hotplug-bugfix.patch

In the current 2.6.14-rc2-git6 kernel, performing a Dynamic LPAR Add
of a hotplug slot will crash the system, with the following (abbreviated)
stack trace:

cpu 0x3: Vector: 700 (Program Check) at [c000000053dff7f0]
    pc: c0000000004f5974: .__alloc_bootmem+0x0/0xb0
    lr: c0000000000258a0: .update_dn_pci_info+0x108/0x118
        c0000000000257c8 .update_dn_pci_info+0x30/0x118 (unreliable)
        c0000000000258fc .pci_dn_reconfig_notifier+0x4c/0x64
        c000000000060754 .notifier_call_chain+0x68/0x9c

The root cause was that __init __alloc_bootmem() was called long after
boot had finished, resulting in a crash because this routine is undefined
after boot time.  The patch below fixes this crash, and adds some docs to
clarify the code.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

08-eeh-spin-counter.patch

One an EEH event is triggers, all further I/O to a device is blocked (until
reset).  Bad device drivers may end up spinning in their interrupt handlers,
trying to read an interrupt status register that will never change state.
This patch moves that spin counter to a per-device structure, and adds
some diagnostic prints to help locate the bad driver.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

07-eeh-report-race.patch

When a PCI slot is isolated, all PCI functions under that slot are affected.
If hese functions have separate device drivers, the EEH isolation event
might be reported multiple times. This patch adds a lock to prevent the
racing of such multiple reports. It also marks every device under the slot
as having experienced an EEH event, so that multiple reports may be
recognized more easily.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

06-eeh-empty-slot-error.patch

Performing PCI config-space reads to empty PCI slots can lead to reports of
"permanent failure" from the firmware. Ignore permanent failures on empty slots.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

05-eeh-slot-error-detail.patch

This patch encapsulates a section of code that reports the EEH event.
The new subroutine can be used in several places to report the error.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

04-eeh-statistics.patch

This minor patch adds some statistics-gathering counters that allow the
behaviour of the EEH subsystem o be monitored. While far from perfect,
it does provide a rudimentary device that makes understanding of the
current state of the system a bit easier.
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

03-eeh-addr-cache-cleanup.patch

This is a minor patch to clean up a buglet related to the PCI address cache.
(The buglet doesn't manifes itself unless there are also bugs elsewhere,
which is why its minor.).  Also:

-- Improved debug printing.
-- Declare some private routines as static
-- Adds reference counting to struct pci_dn->pcidev structure
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

02-eeh-minor-cleanup.patch

This patch performs some minor cleanup of the eeh.c file, including:
-- trim some trailing whitespace
-- remove extraneous #includes
-- use the macro PCI_DN uniformly, instead of the void pointer chase.
-- typos in comments
-- improved debug printk's
Signed-off-by: NLinas Vepstas <linas@linas.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

01-pci-dn-uniformization.patch

This patch changes the rtas_pci interface to use the new struct pci_dn
structure for two routines that work with pci device nodes.

This patch also does some minor janitorial work: it uses some handy macros
and cleans up some trailing whitespace in the affected file.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Early calls to __ioremap() will panic if the hash insertion fails. This
patch makes them return NULL instead. It happens with some pSeries users
who enabled CONFIG_BOOTX_TEXT. The later is getting an incorrect address
for the fame buffer and the hash insertion fails. With this patch, it
will display an error instead of crashing at boot.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix a few compile warnings

arch/ppc64/boot/addRamDisk.c:166: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:170: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:265: warning: unsigned int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:302: warning: unsigned int format, long unsigned int arg (arg 3)
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

A stripped vmlinux does not contain enough symbols to recreate the
System.map.  The System.map file is only used to determine the end of
the runtime memory size.  This is the same value (rounded up to
PAGE_SIZE) as ->memsiz in the ELF program header.

Also, the target vmlinux.initrd doesnt work in 2.6.14:

  arch/ppc64/boot/addRamDisk arch/ppc64/boot/ramdisk.image.gz vmlinux.strip arch/ppc64/boot/vmlinux.initrd
  Name of vmlinux output file missing.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use a local variable for the input filenames.
Signed-off-by: NOlaf Hering <olh@suse.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>